Abstract: An experiment of vented gas explosions involving two
different cylinder vessel volumes (0.2 and 0.0065 m3) was reported,
with equivalence ratio (Φ) ranged from 0.3 to 1.6. Both vessels were
closed at the rear end and fitted at the other side with a circular
orifice plate that gives a constant vent coefficient (K =Av/V2/3) of
16.4. It was shown that end ignition gives higher overpressures than
central ignition, even though most of the published work on venting
uses central ignition. For propane and ethylene, it is found that rich
mixtures gave the highest overpressures and these mixtures are not
considered in current vent design guidance; which the guideline is
based on mixtures giving the maximum flame temperature. A strong
influence of the vessel volume at constant K was found for methane,
propane, ethylene and hydrogen-air explosions. It can be concluded
that self- acceleration of the flame, which is dependent on the
distance of a flame from the ignition and the ‘suction’ at the vent
opening are significant factors affecting the vent flow during
explosion development in vented gas explosion. This additional
volume influence on vented explosions is not taken into account in
the current vent design guidance.
Abstract: This study investigated climatic factors associated
with influenza cases in Southern Thailand. The main aim for use
regression analysis to investigate possible causual relationship of
climatic factors and variability between the border of the Andaman
Sea and the Gulf of Thailand. Southern Thailand had the highest
Influenza incidences among four regions (i.e. north, northeast, central
and southern Thailand). In this study, there were 14 climatic factors:
mean relative humidity, maximum relative humidity, minimum
relative humidity, rainfall, rainy days, daily maximum rainfall,
pressure, maximum wind speed, mean wind speed, sunshine duration,
mean temperature, maximum temperature, minimum temperature,
and temperature difference (i.e. maximum – minimum temperature).
Multiple stepwise regression technique was used to fit the statistical
model. The results indicated that the mean wind speed and the
minimum relative humidity were positively associated with the
number of influenza cases on the Andaman Sea side. The maximum
wind speed was positively associated with the number of influenza
cases on the Gulf of Thailand side.
Abstract: The hydrodynamic processes in bubbly liquid flowing
in tubes and nozzles are studied theoretically and numerically. The
principal regularities of non-stationary processes of boiling liquid
outflow are established under conditions of experiments when the
depressurization of a tube with high pressure inside occurs. The
steady-state solution of bubbly liquid flow in the nozzle of round
cross section with high pressure and temperature conditions inside
bubbles is studied accounting for phase transition and chemical
reactions.
Abstract: Gas condensate Reservoirs show complicated thermodynamic behavior when their pressure reduces to under dew point pressure. Condensate blockage around the producing well cause significant reduction of production rate as well bottom-hole pressure drops below saturation pressure. The main objective of this work was to examine the well test analysis of naturally fractured lean gas condensate reservoir and investigate the effect of condensate formed around the well-bore on behavior of single phase pseudo pressure and its derivative curves. In this work a naturally fractured lean gas condensate reservoir is simulated with compositional simulator. Different sensitivity analysis done on Corry parameters and result of simulator is feed to analytical well testing software. For consideration of these phenomena eighteen compositional models with Capillary number effect are constructed. Matrix relative permeability obeys Corry relative permeability and relative permeability in fracture is linear. Well testing behavior of these models are studied and interpreted. Results show different sensitivity analysis on relative permeability of matrix does not have strong effect on well testing behavior even most part of the matrix around the well is occupied with condensate.
Abstract: In order to investigate a PROX microreactor
performance, two-dimensional modeling of the reacting flow
between two parallel plates is performed through a finite volume
method using an improved SIMPLE algorithm. A three-step surface
kinetics including hydrogen oxidation, carbon monoxide oxidation
and water-gas shift reaction is applied for a Pt-Fe/γ-Al2O3 catalyst
and operating temperatures of about 100ºC. Flow pattern, pressure
field, temperature distribution, and mole fractions of species are
found in the whole domain for all cases. Also, the required reactive
length for removing carbon monoxide from about 2% to less than 10
ppm is found. Furthermore, effects of hydraulic diameter, wall
temperature, and inlet mole fraction of air and water are investigated
by considering carbon monoxide selectivity and conversion. It is
found that air and water addition may improve the performance of
the microreactor in carbon monoxide removal in such operating
conditions; this is in agreement with the pervious published results.
Abstract: One of the approaches to democratization is the fostering of civil society organizations. In Africa, civil society organizations did not fully play their role in the continent-s democratization process due to many factors including the repressive regulations imposed on them by governing parties. In Ethiopia, for the first time in the country-s political history, the civil society played a very active role in the 2005 multi-party election. The involvement of the civil society in this election has far-reaching consequences. One of the objectives of this paper is to assess the consequences of such involvement for both the civil society and the political society in the country. The paper also examines the peculiarities of civil society formation in Africa in general, and in Ethiopia in particular by assessing both the “traditional" and “modern" civil society organizations.
Abstract: In pressure vessels contain hydrogen, the role of
hydrogen will be important because of hydrogen cracking problem. It
is difficult to predict what is happened in metallurgical field spite of a
lot of studies have been searched. The main role in controlling the
mass diffusion as driving force is related to stress. In this study, finite
element analysis is implemented to estimate material-s behavior
associated with hydrogen embrittlement. For this purpose, one model
of a pressure vessel is introduced that it has definite boundary and
initial conditions. In fact, finite element is employed to solve the
sequentially coupled mass diffusion with stress near a crack front in a
pressure vessel. Modeling simulation intergrarnular fracture of AISI
4135 steel due to hydrogen is investigated. So, distribution of
hydrogen and stress are obtained and they indicate that their
maximum amounts occur near the crack front. This phenomenon is
happened exactly the region between elastic and plastic field.
Therefore, hydrogen is highly mobile and can diffuse through crystal
lattice so that this zone is potential to trap high volume of hydrogen.
Consequently, crack growth and fast fracture will be happened.
Abstract: This paper considers a robust recovery of sparse frequencies
from partial phase-only measurements. With the proposed
method, sparse frequencies can be reconstructed, which makes full
use of the sparse distribution in the Fourier representation of the
complex-valued time signal. Simulation experiments illustrate the
proposed method-s advantages over conventional methods in both
noiseless and additive white Gaussian noise cases.
Abstract: Capacity and efficiency of any refrigerating system
diminish rapidly as the difference between the evaporating and
condensing temperature is increased by reduction in the evaporator
temperature. The single stage vapour compression refrigeration
system is limited to an evaporator temperature of -40 0C. Below
temperature of -40 0C the either cascade refrigeration system or multi
stage vapour compression system is employed. Present work
describes thermal design of main three heat exchangers namely
condenser (HTS), cascade condenser and evaporator (LTS) of
R404A-R508B and R410A-R23 cascade refrigeration system. Heat
transfer area of condenser (HTS), cascade condenser and evaporator
(LTS) for both systems have been compared and the effect of
condensing and evaporating temperature on heat-transfer area for
both systems have been studied under same operating condition. The
results shows that the required heat-transfer area of condenser and
cascade condenser for R410A-R23 cascade system is lower than the
R404A-R508B cascade system but heat transfer area of evaporator is
similar for both the system. The heat transfer area of condenser and
cascade condenser decreases with increase in condensing temperature
(Tc), whereas the heat transfer area of cascade condenser and
evaporator increases with increase in evaporating temperature (Te).
Abstract: The paper presents a comparative performance of the
models developed to predict 28 days compressive strengths using
neural network techniques for data taken from literature (ANN-I) and
data developed experimentally for SCC containing bottom ash as
partial replacement of fine aggregates (ANN-II). The data used in the
models are arranged in the format of six and eight input parameters
that cover the contents of cement, sand, coarse aggregate, fly ash as
partial replacement of cement, bottom ash as partial replacement of
sand, water and water/powder ratio, superplasticizer dosage and an
output parameter that is 28-days compressive strength and
compressive strengths at 7 days, 28 days, 90 days and 365 days,
respectively for ANN-I and ANN-II. The importance of different
input parameters is also given for predicting the strengths at various
ages using neural network. The model developed from literature data
could be easily extended to the experimental data, with bottom ash as
partial replacement of sand with some modifications.
Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: In this paper, we propose a method to reduce the
various kinds of noise while gathering and recording the
electrocardiogram (ECG) signal. Because of the defects of former
method in the noise elimination of ECG signal, we use translation
invariant (TI) multiwavelet denoising method to the noise elimination.
The advantage of the proposed method is that it may not only remain
the geometrical characteristics of the original ECG signal and keep the
amplitudes of various ECG waveforms efficiently, but also suppress
impulsive noise to some extent. The simulation results indicate that the
proposed method are better than former removing noise method in
aspects of remaining geometrical characteristics of ECG signal and the
signal-to-noise ratio (SNR).
Abstract: Hospitals in southern Hualien teamed with the
Hypertension Joint Care Network. Working with the network, the
team provided a special designed health education to the individual
who had been identified as a hypertension patient in the outpatient
department. Some metabolism improvements achieved. This is a
retrospective study by purposively taking 106 patients from a hospital
between 2008 and 2010. Records of before and after education
intervention of the objects was collected and analyzed to see the how
the intervention affected the patients- hypertension control via clinical
parameter monitoring. The results showed that the clinical indicators,
the LDL-C, the cholesterol and the systolic blood pressure were
significantly improved. The study provides evidence for the
effectiveness of the network in controlling hypertension.
Abstract: The rheological properties of light crude oil and its mixture with water were investigated experimentally. These rheological properties include steady flow behavior, yield stress, transient flow behavior, and viscoelastic behavior. A RheoStress RS600 rheometer was employed in all of the rheological examination tests. The light crude oil exhibits a Newtonian and for emulsion exhibits a non-Newtonian shear thinning behavior over the examined shear rate range of 0.1–120 s-1. In first time, a series of samples of crude oil from the Algerian Sahara has been tested and the results expressed in terms of τ=f(γ) have demonstrated their Newtonian character for the temperature included in [20°C, 70°C]. In second time and at T=20°C, the oil-water emulsions (30%, 50% and 70%) by volume of water), thermodynamically stable, have demonstrated a non-Newtonian rheological behavior that is to say, Herschel-Bulkley and Bingham types. For each type of crude oil-water emulsion, the rheological parameters are calculated by numerical treatment of results.
Abstract: Tribological behavior and wear regimes of ascast
and heattreted Al-Cu-Mg matrix composites containing SiC
particles were studied using a pin-on-disc wear testing apparatus
against an EN32 steel counterface giving emphasis on wear rate as
a function of applied pressures (0.2, 0.6, 1.0 and 1.4 MPa) at
different sliding distances (1000, 2000, 3000, 4000 and 5000
meters) and at a fixed sliding speed of 3.35m/s. The results showed
that the composite exhibited lower wear rate than that of the matrix
alloy and the wear rate of the composites is noted to be invariant to
the sliding distance and is reducing by heat treatment. Wear
regimes such as low, mild and severe wear were observed as per the
Archard-s wear calculations. It is very interesting to note that the
mild wear is almost constant in all the wear regimes.
Abstract: Sensors possess several properties of physical
measures. Whether devices that convert a sensed signal into an
electrical signal, chemical sensors and biosensors, thus all these
sensors can be considered as an interface between the physical and
electrical equipment. The problem is the analysis of the multitudes of
saved settings as input variables. However, they do not all have the
same level of influence on the outputs. In order to identify the most
sensitive parameters, those that can guide users in gathering
information on the ground and in the process of model calibration
and sensitivity analysis for the effect of each change made.
Mathematical models used for processing become very complex.
In this paper a fuzzy rule-based system is proposed as a solution
for this problem. The system collects the available signals
information from sensors. Moreover, the system allows the study of
the influence of the various factors that take part in the decision
system. Since its inception fuzzy set theory has been regarded as a
formalism suitable to deal with the imprecision intrinsic to many
problems. At the same time, fuzzy sets allow to use symbolic models.
In this study an example was applied for resolving variety of
physiological parameters that define human health state. The
application system was done for medical diagnosis help. The inputs
are the signals expressed the cardiovascular system parameters, blood
pressure, Respiratory system paramsystem was done, it will be able
to predict the state of patient according any input values.
Abstract: Analysis of blood vessel mechanics in normal and
diseased conditions is essential for disease research, medical device
design and treatment planning. In this work, 3D finite element
models of normal vessel and atherosclerotic vessel with 50% plaque
deposition were developed. The developed models were meshed
using finite number of tetrahedral elements. The developed models
were simulated using actual blood pressure signals. Based on the
transient analysis performed on the developed models, the parameters
such as total displacement, strain energy density and entropy per unit
volume were obtained. Further, the obtained parameters were used to
develop artificial neural network models for analyzing normal and
atherosclerotic blood vessels. In this paper, the objectives of the
study, methodology and significant observations are presented.
Abstract: Kombucha Tea Ferment (KT), was given to male
albino rats, (1ml/Kg of body weight), via gavages, during 2 weeks
before intraperitoneal administration of 3.5 mg/Kg body weight
CdCl2 and/or whole body γ-irradiation with 4Gy, and during 4 weeks
after each treatment. Hepatic and nephritic pathological changes
included significant increases of serum alanine transaminase (ALT),
aspartate transaminase (AST), and alkaline phosphatase (ALP)
activities, and creatinine and urea contents with significant decrease
in serum total antioxidant capacity (TAC). Increase in oxidative
stress markers in liver and kidney tissues expressed by significant
increase in malondialdehyde (MDA) and nitric oxide (NO) contents
associated to significant depletion in superoxide dismutase (SOD)
and catalase (CAT) activities, and reduced glutathione (GSH) content
were recorded. KT administration results in recovery of all the
pathological changes. It could be concluded that KT might protect
liver and kidney from oxidative damage induced by exposure to
cadmium and/ or γ-irradiation.
Abstract: This paper evaluates the dividend payments for general
claim size distributions in the presence of a dividend barrier. The
surplus of a company is modeled using the classical risk process
perturbed by diffusion, and in addition, it is assumed to accrue interest
at a constant rate. After presenting the integro-differential equation
with initial conditions that dividend payments satisfies, the paper
derives a useful expression of the dividend payments by employing
the theory of Volterra equation. Furthermore, the optimal value of
dividend barrier is found. Finally, numerical examples illustrate the
optimality of optimal dividend barrier and the effects of parameters
on dividend payments.
Abstract: Wood as a natural renewable material is vulnerable to
degradation by microorganisms and susceptible to change in
dimension by water. In order to effectively improve the durability of
wood, an active reagent, maleic anhydride (Man) was selected for
wood modification. Man was first dissolved into a solvent, and then
penetrated into wood porous structure under a vacuum/pressure
condition. After a final catalyst-thermal treatment, wood modification
was finished. The test results indicate that acetone is a good solvent for
transporting Man into wood matrix. SEM observation proved that
wood samples treated by Man kept a good cellular structure, indicating
a well penetration of Man into wood cell walls. FTIR analysis
suggested that Man reacted with hydroxyl groups on wood cell walls
by its ring-ether group, resulting in reduction of amount of hydroxyl
groups and resultant good dimensional stability as well as fine decay
resistance. Consequently, Man modifying wood to improve its
durability is an effective method.