Abstract: This paper presents a novel approach for tuning unified power flow controller (UPFC) based damping controller in order to enhance the damping of power system low frequency oscillations. The design problem of damping controller is formulated as an optimization problem according to the eigenvalue-based objective function which is solved using iteration particle swarm optimization (IPSO). The effectiveness of the proposed controller is demonstrated through eigenvalue analysis and nonlinear time-domain simulation studies under a wide range of loading conditions. The simulation study shows that the designed controller by IPSO performs better than CPSO in finding the solution. Moreover, the system performance analysis under different operating conditions show that the δE based controller is superior to the mB based controller.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: The parametrical study of Shrouded Contra-rotating
Rotor was done in this paper based on 2D axisymmetric simulations.
The calculations were made with an actuator disk as double rotor
model. It objects to explore and quantify the effects of different shroud
geometry parameters mainly using the performance of power loading
(PL), which could evaluate the whole propulsion system capability as
5 Newtontotal thrust generationfor hover demand. The numerical
results show that:The increase of nozzle radius is desired but limited
by the flow separation, its optimal design is around 1.15 times rotor
radius, the viscosity effects greatly constraint the influence of nozzle
shape, the divergent angle around 10.5° performs best for chosen
nozzle length;The parameters of inlet such as leading edge curvature,
radius and internal shape do not affect thrust great but play an
important role in pressure distribution which could produce most part
of shroud thrust, they should be chosen according to the reduction of
adverse pressure gradients to reduce the risk of boundary separation.
Abstract: One of Effective parameters on the performance of linear induction motors is number of poles which must be selected and optimized to increase power efficiency and motor performance significantly. In this paper a double-sided linear induction motor with different poles number by using MAXWELL3D software is designed and with finite element method is analyzed electromagnetically. Then for dynamic simulation, linear motor by using MATLAB software is simulated. The results show that by adding poles number, system time response is increased and motor after more time reaches to steady state. Also propulsion force of motor is increased.
Abstract: Full - Scale Accelerated Loading System, one part of
“the Eleventh - Five - Year National Grand Technology Infrastructure
Program" is a facility to evaluate the performance and service life of
different kinds of pavements subjected to traffic loading under full -
controlled environment. While simulating the environments of frigid
zone and permafrost zone, the accurate control of air temperature, road
temperature and roadbed temperature are the key points and also
aporias for the designment. In this paper, numerical simulations are
used to determine the design parameters of the frozen soil simulation
system. At first, a brief introduction of the Full - Scale Accelerate
Loading System was given. Then, the temperature control method of
frozen soil simulation system was proposed. Finally, by using finite
element simulations, the optimal design of frozen soil simulation
system was obtained. This proposed design, which was obtained by
finite element simulations, provided significant referents to the
ultimate design of the environment simulation system.
Abstract: In designing river intakes and diversion structures, it is paramount that the sediments entering the intake are minimized or, if possible, completely separated. Due to high water velocity, sediments can significantly damage hydraulic structures especially when mechanical equipment like pumps and turbines are used. This subsequently results in wasting water, electricity and further costs. Therefore, it is prudent to investigate and analyze the performance of lateral intakes affected by sediment control structures. Laboratory experiments, despite their vast potential and benefits, can face certain limitations and challenges. Some of these include: limitations in equipment and facilities, space constraints, equipment errors including lack of adequate precision or mal-operation, and finally, human error. Research has shown that in order to achieve the ultimate goal of intake structure design – which is to design longlasting and proficient structures – the best combination of sediment control structures (such as sill and submerged vanes) along with parameters that increase their performance (such as diversion angle and location) should be determined. Cost, difficulty of execution and environmental impacts should also be included in evaluating the optimal design. This solution can then be applied to similar problems in the future. Subsequently, the model used to arrive at the optimal design requires high level of accuracy and precision in order to avoid improper design and execution of projects. Process of creating and executing the design should be as comprehensive and applicable as possible. Therefore, it is important that influential parameters and vital criteria is fully understood and applied at all stages of choosing the optimal design. In this article, influential parameters on optimal performance of the intake, advantages and disadvantages, and efficiency of a given design are studied. Then, a multi-criterion decision matrix is utilized to choose the optimal model that can be used to determine the proper parameters in constructing the intake.
Abstract: Stair climbing is one of critical issues for field robots to
widen applicable areas. This paper presents optimal design on
kinematic parameters of a new robotic platform for stair climbing. The
robotic platform climbs various stairs by body flip locomotion with
caterpillar type main platform. Kinematic parameters such as platform
length, platform height, and caterpillar rotation speed are optimized to
maximize stair climbing stability. Three types of stairs are used to
simulate typical user conditions. The optimal design process is
conducted based on Taguchi methodology, and resulting parameters
with optimized objective function are presented. In near future, a
prototype is assembled for real environment testing.
Abstract: Environmental pollution problems have been globally
main concern in all fields including economy, society and culture into
the 21st century. Beginning with the Kyoto Protocol, the reduction on
the emissions of greenhouse gas such as CO2 and SOX has been a
principal challenge of our day. As most buildings unlike durable goods
in other industries have a characteristic and long life cycle, they
consume energy in quantity and emit much CO2. Thus, for green
building construction, more research is needed to reduce the CO2
emissions at each stage in the life cycle. However, recent studies are
focused on the use and maintenance phase. Also, there is a lack of
research on the initial design stage, especially the structure design.
Therefore, in this study, we propose an optimal design plan
considering CO2 emissions and cost in composite buildings
simultaneously by applying to the structural design of actual building.
Abstract: Coagulation of water involves the use of coagulating
agents to bring the suspended matter in the raw water together for
settling and the filtration stage. Present study is aimed to examine the
effects of aluminum sulfate as coagulant in conjunction with Moringa
Oleifera Coagulant Protein as coagulant aid on turbidity, hardness,
and bacteria in turbid water. A conventional jar test apparatus was
employed for the tests. The best removal was observed at a pH of 7
to 7.5 for all turbidities. Turbidity removal efficiency was resulted
between % 80 to % 99 by Moringa Oleifera Coagulant Protein as
coagulant aid. Dosage of coagulant and coagulant aid decreased with
increasing turbidity. In addition, Moringa Oleifera Coagulant Protein
significantly has reduced the required dosage of primary coagulant.
Residual Al+3 in treated water were less than 0.2 mg/l and meets the
environmental protection agency guidelines. The results showed that
turbidity reduction of % 85.9- % 98 paralleled by a primary
Escherichia coli reduction of 1-3 log units (99.2 – 99.97%) was
obtained within the first 1 to 2 h of treatment. In conclusions,
Moringa Oleifera Coagulant Protein as coagulant aid can be used for
drinking water treatment without the risk of organic or nutrient
release. We demonstrated that optimal design method is an efficient
approach for optimization of coagulation-flocculation process and
appropriate for raw water treatment.
Abstract: The Prediction of aerodynamic characteristics and
shape optimization of airfoil under the ground effect have been carried
out by integration of computational fluid dynamics and the multiobjective
Pareto-based genetic algorithm. The main flow
characteristics around an airfoil of WIG craft are lift force, lift-to-drag
ratio and static height stability (H.S). However, they show a strong
trade-off phenomenon so that it is not easy to satisfy the design
requirements simultaneously. This difficulty can be resolved by the
optimal design. The above mentioned three characteristics are chosen
as the objective functions and NACA0015 airfoil is considered as a
baseline model in the present study. The profile of airfoil is
constructed by Bezier curves with fourteen control points and these
control points are adopted as the design variables. For multi-objective
optimization problems, the optimal solutions are not unique but a set
of non-dominated optima and they are called Pareto frontiers or Pareto
sets. As the results of optimization, forty numbers of non- dominated
Pareto optima can be obtained at thirty evolutions.
Abstract: This paper describes the shape optimization of impeller
blades for a anti-heeling bidirectional axial flow pump used in ships.
In general, a bidirectional axial pump has an efficiency much lower
than the classical unidirectional pump because of the symmetry of the
blade type. In this paper, by focusing on a pump impeller, the shape of
blades is redesigned to reach a higher efficiency in a bidirectional axial
pump. The commercial code employed in this simulation is CFX v.13.
CFD result of pump torque, head, and hydraulic efficiency was
compared. The orthogonal array (OA) and analysis of variance
(ANOVA) techniques and surrogate model based optimization using
orthogonal polynomial, are employed to determine the main effects
and their optimal design variables. According to the optimal design,
we confirm an effective design variable in impeller blades and explain
the optimal solution, the usefulness for satisfying the constraints of
pump torque and head.
Abstract: In this paper the vibration behaviors of a structure equipped with a tuned liquid column damper (TLCD) under a harmonic type of earthquake loading are studied. However, due to inherent nonlinear liquid damping, it is no doubt that a great deal of computational effort is required to search the optimum parameters of the TLCD, numerically. Therefore by linearization the equation of motion of the single degree of freedom structure equipped with the TLCD, the closed form solutions of the TLCD-structure system are derived. To find the reliability of the analytical method, the results have been compared with other researcher and have good agreement. Further, the effects of optimal design parameters such as length ratio and mass ratio on the performance of the TLCD for controlling the responses of a structure are investigated by using the harmonic type of earthquake excitation. Finally, the Citicorp Center which has a very flexible structure is used as an example to illustrate the design procedure for the TLCD under the earthquake excitation.
Abstract: In the real application of active control systems to
mitigate the response of structures subjected to sever external
excitations such as earthquake and wind induced vibrations, since the
capacity of actuators is limited then the actuators saturate. Hence, in
designing controllers for linear and nonlinear structures under sever
earthquakes, the actuator saturation should be considered as a
constraint. In this paper optimal design of active controllers for
nonlinear structures by considering the actuator saturation has been
studied. To this end a method has been proposed based on defining
an optimization problem which considers the minimizing of the
maximum displacement of the structure as objective when a limited
capacity for actuator has been used as a constraint in optimization
problem. To evaluate the effectiveness of the proposed method, a
single degree of freedom (SDF) structure with a bilinear hysteretic
behavior has been simulated under a white noise ground acceleration
of different amplitudes. Active tendon control mechanism, comprised
of pre-stressed tendons and an actuator, and extended nonlinear
Newmark method based instantaneous optimal control algorithm
have been used as active control mechanism and algorithm. To
enhance the efficiency of the controllers, the weights corresponding
to displacement, velocity, acceleration and control force in the
performance index have been found by using the Distributed Genetic
Algorithm (DGA). According to the results it has been concluded
that the proposed method has been effective in considering the
actuator saturation in designing optimal controllers for nonlinear
frames. Also it has been shown that the actuator capacity and the
average value of required control force are two important factors in
designing nonlinear controllers for considering the actuator
saturation.
Abstract: Permanent magnet synchronous machines are known
as a good candidate for hybrid electric vehicles due to their unique
merits. However they have two major drawbacks i.e. high cost and
small speed range. In this paper an optimal design of a permanent
magnet machine is presented. A reduction of permanent magnet
material for a constant torque and an extension in speed and torque
ranges are chosen as the optimization aims. For this purpose the
analytical model of the permanent magnet synchronous machine is
derived and the appropriate design algorithm is devised. The genetic
algorithm is then employed to optimize some machine specifications.
Finally the finite element method is used to validate the designed
machine.
Abstract: Multi-energy systems will enhance the system
reliability and power quality. This paper presents an integrated
approach for the design and operation of distributed energy resources
(DER) systems, based on energy hub modeling. A multi-objective
optimization model is developed by considering an integrated view of
electricity and natural gas network to analyze the optimal design and
operating condition of DER systems, by considering two conflicting
objectives, namely, minimization of total cost and the minimization
of environmental impact which is assessed in terms of CO2
emissions. The mathematical model considers energy demands of the
site, local climate data, and utility tariff structure, as well as technical
and financial characteristics of the candidate DER technologies. To
provide energy demands, energy systems including photovoltaic, and
co-generation systems, boiler, central power grid are considered. As
an illustrative example, a hotel in Iran demonstrates potential
applications of the proposed method. The results prove that
increasing the satisfaction degree of environmental objective leads to
increased total cost.
Abstract: A model is presented to find the optimal design of the
mixed renewable warranty policy for non-repairable Weibull life
products. The optimal design considers the conflict of interests
between the customer and the manufacturer: the customer interests
are longer full rebate coverage period and longer total warranty
coverage period, the manufacturer interests are lower warranty cost
and lower risk. The design factors are full rebate and total warranty
coverage periods. Results showed that mixed policy is better than full
rebate policy in terms of risk and total warranty coverage period in all
of the three bathtub regions. In addition, results showed that linear
policy is better than mixed policy in infant mortality and constant
failure regions while the mixed policy is better than linear policy in
ageing region of the model. Furthermore, the results showed that
using burn-in period for infant mortality products reduces warranty
cost and risk.
Abstract: Since the actuator capacity is limited, in the real
application of active control systems under sever earthquakes it is
conceivable that the actuators saturate, hence the actuator saturation
should be considered as a constraint in design of optimal controllers.
In this paper optimal design of active controllers for nonlinear
structures by considering actuator saturation, has been studied. The
proposed method for designing optimal controllers is based on
defining an optimization problem which the objective has been to
minimize the maximum displacement of structure when a limited
capacity for actuator has been used. To this end a single degree of
freedom (SDF) structure with a bilinear hysteretic behavior has been
simulated under a white noise ground acceleration of different
amplitudes. Active tendon control mechanism, comprised of prestressed
tendons and an actuator, and extended nonlinear Newmark
method based instantaneous optimal control algorithm have been
used. To achieve the best results, the weights corresponding to
displacement, velocity, acceleration and control force in the
performance index have been optimized by the Distributed Genetic
Algorithm (DGA). Results show the effectiveness of the proposed
method in considering actuator saturation. Also based on the
numerical simulations it can be concluded that the actuator capacity
and the average value of required control force are two important
factors in designing nonlinear controllers which consider the actuator
saturation.
Abstract: Giving birth is a natural process and most women have to go through it. Gynecologist or Midwife usually uses the leg holder to position the cervix in the stitching process. In some part of rural areas in Indonesia, the labor process normally being done at homes by calling in a midwife or gynecologist. The facilities for this kind of labor process is not yet sufficient, as the use of leg holder supposedly on the obstetric bed. The reality is that it is impossible to bring in the obstetric bed to the patient-s house at the time they call for giving birth or the time when the stitching of the cervix need to be done. This research is redesigning the leg holder through Biomechanics and ergonomic approaches to obtain the optimal design which is suitable to the user of a developing country such as Indonesia.
Abstract: The scientific perspective, the practice area of physical education and sports activities improve power capacity in all its forms of expression, being a generator of the research topics. Today theories that strength training athletes and slow down development progress will affect the strength and flexibility are discredited. On the other hand there are sectors and / or samples whose results are sports of the way higher manifestation of power as a result of the composition of the force and velocity, being based in this respect on the systematic and continuous development of both bio-motric capacities said. Training of force for children was and is controversial. Teama de accidentări sau a stopării premature a procesului de creştere a făcut ca în trecut copiii să fie ţinuţi departe de lucrul cu diferite greutăţi.Fear of injury or premature stop the growth process in the past made the children to be kept away from working with different weights. Recent studies have shown that the risk of accidents is relatively small and the strength training can help prevent them. For example, most accidents occur at the level of athletics ligaments and tendons. From this point of view, it can be said that a progressive intervention of force training, optimal design, will help enhancing their process, such as athlete much better prepared to meet training requests and competitions. Preparation of force provides a solid basis for further phases in the highest performance.
Abstract: This paper examines many mathematical methods for
molding the hourly price forward curve (HPFC); the model will be
constructed by numerous regression methods, like polynomial
regression, radial basic function neural networks & a furrier series.
Examination the models goodness of fit will be done by means of
statistical & graphical tools. The criteria for choosing the model will
depend on minimize the Root Mean Squared Error (RMSE), using the
correlation analysis approach for the regression analysis the optimal
model will be distinct, which are robust against model
misspecification. Learning & supervision technique employed to
determine the form of the optimal parameters corresponding to each
measure of overall loss. By using all the numerical methods that
mentioned previously; the explicit expressions for the optimal model
derived and the optimal designs will be implemented.