Abstract: Rapid urbanization changes the land use/land cover pattern of a developing region. Due to these land surface changes, stream flow of the rivers also changes. It is important to investigate the factors affecting hydrological characteristics of the river basin for better river basin management planning. This study is aimed to understand the effect of Land Use/Land Cover (LU/LC) changes on stream flow of Upper Bhima River basin which is highly stressed in terms of water resources. In this study, Upper Bhima River basin is divided into two adjacent sub-watersheds: Mula-Mutha (urbanized) sub-watershed and Bhima (non-urbanized) sub-watershed. First of all, LU/LC changes were estimated over 1980, 2002, and 2009 for both Mula-Mutha and Bhima sub-watersheds. Further, stream flow simulations were done using Soil and Water Assessment Tool (SWAT) for the streams draining both watersheds. Results revealed that stream flow was relatively higher for urbanized sub-watershed. Through Sensitivity Analysis it was observed that out of all the parameters used, base flow was the most sensitive parameter towards LU/LC changes.
Abstract: Most thermal power plants use steam as working fluid in their power cycle. Therefore, in addition to fuel, water is the other main input for thermal plants. Water and steam must be highly pure in order to protect the systems from corrosion, scaling and biofouling. Pure process water is produced in water treatment plants having many several treatment methods. Treatment plant design is selected depending on raw water source and required water quality. Although working principle of fossil-fuel fired thermal power plants are same, there is no standard design and equipment arrangement valid for all thermal power plant utility systems. Besides that, there are many other technology evaluation and selection criteria for designing the most optimal water systems meeting the requirements such as local conditions, environmental restrictions, electricity and other consumables availability and transport, process water sources and scarcity, land use constraints etc. Aim of this study is explaining the adopted methodology for technology selection for process water preparation and industrial waste water treatment plant in a thermal power plant project located in Tufanbeyli, Adana Province in Turkey. Thermal power plant is fired with indigenous lignite coal extracted from adjacent lignite reserves. This paper addresses all above-mentioned factors affecting the thermal power plant water treatment facilities (demineralization + waste water treatment) design and describes the ultimate design of Tufanbeyli Thermal Power Plant Water Treatment Plant.
Abstract: In recent decades, rapid and incorrect changes in land-use have been associated with consequences such as natural resources degradation and environmental pollution. Detecting changes in land-use is one of the tools for natural resource management and assessment of changes in ecosystems. The target of this research is studying the land-use changes in Haraz basin with an area of 677000 hectares in a 15 years period (1996 to 2011) using LANDSAT data. Therefore, the quality of the images was first evaluated. Various enhancement methods for creating synthetic bonds were used in the analysis. Separate training sites were selected for each image. Then the images of each period were classified in 9 classes using supervised classification method and the maximum likelihood algorithm. Finally, the changes were extracted in GIS environment. The results showed that these changes are an alarm for the HARAZ basin status in future. The reason is that 27% of the area has been changed, which is related to changing the range lands to bare land and dry farming and also changing the dense forest to sparse forest, horticulture, farming land and residential area.
Abstract: Environmental performance of artisanal brick manufacture was studied by Lifecycle Assessment (LCA) methodology and Computational Fluid Dynamics (CFD) analysis in Mexico. The main objective of this paper is to evaluate the environmental impact during artisanal brick manufacture. LCA cradle-to-gate approach was complemented with CFD analysis to carry out an Environmental Impact Assessment (EIA). The lifecycle includes the stages of extraction, baking and transportation to the gate. The functional unit of this study was the production of a single brick in Chihuahua, Mexico and the impact categories studied were carcinogens, respiratory organics and inorganics, climate change radiation, ozone layer depletion, ecotoxicity, acidification/ eutrophication, land use, mineral use and fossil fuels. Laboratory techniques for fuel characterization, gas measurements in situ, and AP42 emission factors were employed in order to calculate gas emissions for inventory data. The results revealed that the categories with greater impacts are ecotoxicity and carcinogens. The CFD analysis is helpful in predicting the thermal diffusion and contaminants from a defined source. LCA-CFD synergy complemented the EIA and allowed us to identify the problem of thermal efficiency within the system.
Abstract: Reservoirs are being contaminated all around the world with point source and Non-Point Source (NPS) pollution. The most common NPS pollutants are sediments and nutrients. Krishnagiri Reservoir (KR) has been chosen for the present case study, which is located in the tropical semi-arid climatic zone of Tamil Nadu, South India. It is the main source of surface water in Krishnagiri district to meet the freshwater demands. The reservoir has lost about 40% of its water holding capacity due to sedimentation over the period of 50 years. Hence, from the research and management perspective, there is a need for a sound knowledge on the spatial and seasonal variations of KR water quality. The present study encompasses the specific objectives as (i) to investigate the longitudinal heterogeneity and seasonal variations of physicochemical parameters, nutrients and biological characteristics of KR water and (ii) to examine the extent of degradation of water quality in KR. 15 sampling points were identified by uniform stratified method and a systematic monthly sampling strategy was selected due to high dynamic nature in its hydrological characteristics. The physicochemical parameters, major ions, nutrients and Chlorophyll a (Chl a) were analysed. Trophic status of KR was classified by using Carlson's Trophic State Index (TSI). All statistical analyses were performed by using Statistical Package for Social Sciences programme, version-16.0. Spatial maps were prepared for Chl a using Arc GIS. Observations in KR pointed out that electrical conductivity and major ions are highly variable factors as it receives inflow from the catchment with different land use activities. The study of major ions in KR exhibited different trends in their values and it could be concluded that as the monsoon progresses the major ions in the water decreases or water quality stabilizes. The inflow point of KR showed comparatively higher concentration of nutrients including nitrate, soluble reactive phosphorus (SRP), total phosphors (TP), total suspended phosphorus (TSP) and total dissolved phosphorus (TDP) during monsoon seasons. This evidently showed the input of significant amount of nutrients from the catchment side through agricultural runoff. High concentration of TDP and TSP at the lacustrine zone of the reservoir during summer season evidently revealed that there was a significant release of phosphorus from the bottom sediments. Carlson’s TSI of KR ranged between 81 and 92 during northeast monsoon and summer seasons. High and permanent Cyanobacterial bloom in KR could be mainly due to the internal loading of phosphorus from the bottom sediments. According to Carlson’s TSI classification Krishnagiri reservoir was ranked in the hyper-eutrophic category. This study provides necessary basic data on the spatio-temporal variations of water quality in KR and also proves the impact of point and NPS pollution from the catchment area. High TSI warrants a greater threat for the recovery of internal P loading and hyper-eutrophic condition of KR. Several expensive internal measures for the reduction of internal loading of P were introduced by many scientists. However, the outcome of the present research suggests for the innovative algae harvesting technique for the removal of sediment nutrients.
Abstract: Acreage response function are modeled taking account of expected harvest prices, weather related variables and other non-price variables allowing for partial adjustment possibility. At the outset, based on the literature on price expectation formation, we explored suitable formulations for estimating the farmer’s expected prices. Assuming that farmers form expectations rationally, the prices of food and biofuel crops are modeled using time-series methods for possible ARCH/GARCH effects to account for volatility. The prices projected on the basis of the models are then inserted to proxy for the expected prices in the acreage response functions. Food crop acreages in different growing states are found sensitive to their prices relative to those of one or more of the biofuel crops considered. The required percentage improvement in food crop yields is worked to offset the acreage loss.
Abstract: Climate change remains a challenging matter for the human and the built environment in the 21st century, where the need to consider adaptation to climate change in the development process is paramount. However, there remains a lack of information regarding how we should prepare responses to this issue, such as through developing organized and sophisticated tools enabling the adaptation process. This study aims to build a systematic framework approach to investigate the potentials that Neighborhood Sustainability Assessment tools (NSA) might offer in enabling both the analysis of the emerging adaptive capacity to climate change. The analysis of the framework presented in this paper aims to discuss this issue in three main phases. The first part attempts to link sustainability and climate change, in the context of adaptive capacity. It is argued that in deciding to promote sustainability in the context of climate change, both the resilience and vulnerability processes become central. However, there is still a gap in the current literature regarding how the sustainable development process can respond to climate change. As well as how the resilience of practical strategies might be evaluated. It is suggested that the integration of the sustainability assessment processes with both the resilience thinking process, and vulnerability might provide important components for addressing the adaptive capacity to climate change. A critical review of existing literature is presented illustrating the current lack of work in this field, integrating these three concepts in the context of addressing the adaptive capacity to climate change. The second part aims to identify the most appropriate scale at which to address the built environment for the climate change adaptation. It is suggested that the neighborhood scale can be considered as more suitable than either the building or urban scales. It then presents the example of NSAs, and discusses the need to explore their potential role in promoting the adaptive capacity to climate change. The third part of the framework presents a comparison among three example NSAs, BREEAM Communities, LEED-ND, and CASBEE-UD. These three tools have been selected as the most developed and comprehensive assessment tools that are currently available for the neighborhood scale. This study concludes that NSAs are likely to present the basis for an organized framework to address the practical process for analyzing and yet promoting Adaptive Capacity to Climate Change. It is further argued that vulnerability (exposure & sensitivity) and resilience (Interdependence & Recovery) form essential aspects to be addressed in the future assessment of NSA’s capability to adapt to both short and long term climate change impacts. Finally, it is acknowledged that further work is now required to understand impact assessment in terms of the range of physical sectors (Water, Energy, Transportation, Building, Land Use and Ecosystems), Actor and stakeholder engagement as well as a detailed evaluation of the NSA indicators, together with a barriers diagnosis process.
Abstract: Flash flood is occurred in short time rainfall interval:
from 1 hour to 12 hours in small and medium basins. Flash floods
typically have two characteristics: large water flow and big flow
velocity. Flash flood is occurred at hill valley site (strip of lowland of
terrain) in a catchment with large enough distribution area, steep
basin slope, and heavy rainfall. The risk of flash floods is determined
through Gridded Basin Flash Flood Potential Index (GBFFPI). Flash
Flood Potential Index (FFPI) is determined through terrain slope
flash flood index, soil erosion flash flood index, land cover flash
floods index, land use flash flood index, rainfall flash flood index.
Determining GBFFPI, each cell in a map can be considered as outlet
of a water accumulation basin. GBFFPI of the cell is determined as
basin average value of FFPI of the corresponding water accumulation
basin. Based on GIS, a tool is developed to compute GBFFPI using
ArcObjects SDK for .NET. The maps of GBFFPI are built in two
types: GBFFPI including rainfall flash flood index (real time flash
flood warning) or GBFFPI excluding rainfall flash flood index.
GBFFPI Tool can be used to determine a high flash flood potential
site in a large region as quick as possible. The GBFFPI is improved
from conventional FFPI. The advantage of GBFFPI is that GBFFPI is
taking into account the basin response (interaction of cells) and
determines more true flash flood site (strip of lowland of terrain)
while conventional FFPI is taking into account single cell and does
not consider the interaction between cells. The GBFFPI Map of
QuangNam, QuangNgai, DaNang, Hue is built and exported to
Google Earth. The obtained map proves scientific basis of GBFFPI.
Abstract: In this research, we propose to conduct diagnostic and
predictive analysis about the key factors and consequences of urban
population relocation. To achieve this goal, urban simulation models
extract the urban development trends as land use change patterns from
a variety of data sources. The results are treated as part of urban big
data with other information such as population change and economic
conditions. Multiple data mining methods are deployed on this data to
analyze nonlinear relationships between parameters. The result
determines the driving force of population relocation with respect to
urban sprawl and urban sustainability and their related parameters.
This work sets the stage for developing a comprehensive urban
simulation model for catering to specific questions by targeted users. It
contributes towards achieving sustainability as a whole.
Abstract: The aim of sustainable architecture is to design
buildings with the least adverse effects on the environment and
provide better conditions for people. What building forms make the
best use of land? This question was addressed in the late 1960s at the
center of Land Use and Built Form Studies in Cambridge. This led to
a number of influential papers which had a great influence on the
practice of urban design. This paper concentrates on the results of
sustainability caused by climatic conditions in Iranian traditional
architecture in hot-arid regions. As people spent a significant amount
of their time in houses, it was very important to have such houses to
fulfill their needs physically and spiritually as well as satisfying their
cultural and religious aspects of their lifestyles. In a vast country such
as Iran with different climatic zones, traditional builders have
presented series of logical solutions for human comfort. These
solutions have been able to response to the environmental problems
for a long period of time. As a result, by considering the experience
in traditional architecture of hot–arid climate in Iran, it is possible to
attain sustainable architecture.
Abstract: Polycyclic Aromatic Hydrocarbons (PAHs) are
formed mainly because of incomplete combustion of organic
materials during industrial, domestic activities or natural occurrence.
Their toxicity and contamination of terrestrial and aquatic ecosystem
have been established. However, with limited validity index, previous
research has focused on PAHs isomer pair ratios of variable
physicochemical properties in source identification. The objective of
this investigation was to determine the empirical validity of Pearson
Correlation Coefficient (PCC) and Cluster Analysis (CA) in PAHs
source identification along soil samples of different land uses.
Therefore, 16 PAHs grouped, as Endocrine Disruption Substances
(EDSs) were determined in 10 sample stations in top and sub soils
seasonally. PAHs was determined the use of Varian 300 gas
chromatograph interfaced with flame ionization detector. Instruments
and reagents used are of standard and chromatographic grades
respectively. PCC and CA results showed that the classification of
PAHs along pyrolitic and petrogenic organics used in source
signature is about the predominance PAHs in environmental matrix.
Therefore, the distribution of PAHs in the studied stations revealed
the presence of trace quantities of the vast majority of the sixteen
PAHs, which may ultimately inhabit the actual source signature
authentication. Therefore, factors to be considered when evaluating
possible sources of PAHs could be; type and extent of bacterial
metabolism, transformation products/substrates, and environmental
factors such as salinity, pH, oxygen concentration, nutrients, light
intensity, temperature, co-substrates, and environmental medium are
hereby recommended as factors to be considered when evaluating
possible sources of PAHs.
Abstract: With the increasing population and intensive land use,
huge traffic demand is generating worldwide both in developing and
developed countries. As a developing country, Bangladesh is also
facing the same problem in recent years by producing huge numbers
of daily trips. As a matter of fact, extensive traffic demand is
increasing day by day. Also, transport system in Dhaka is
heterogeneous, reflecting the heterogeneity in the socio-economic
and land use patterns. Trips produced here are for different purposes
such as work, business, educational etc. Due to the significant
concentration of educational institutions a large share of the trips are
generated by educational purpose. And one of the major percentages
of educational trips is produced by university going students and
most of them are travelled by car, bus, train, taxi, rickshaw etc. The
aim of the study was to find out the university students’ perception on
public transit ridership. A survey was conducted among 330 students
from eight different universities. It was found out that 26% of the
trips produced by university going students are travelled by public
bus service and only 5% are by train. Percentage of car share is 16%
and 12% of the trips are travelled by private taxi. It has been
observed from the study, students those who prefer bus instead of
other options, 42 percent of their family resides outside Dhaka. And
those who prefer walking, of them, over 40 percent students’ family
reside outside of Dhaka and of them over 85 percent students have a
tendency to live in a mess. On the contrary, students travelling by car
represents, most of their family reside in Dhaka. The study also
revealed that the most important reason that restricts students not to
use public transit is poor service. Negative attitudes such as
discomfort, uneasiness in using public transit also reduces the usage
of public transit. The poor waiting area is another major cause of not
using public transit. Insufficient security also plays a significant role
in not using public transit. On the contrary, the fare is not a problem
for students those who use public transit as a mode of transportation.
Students also think stations are not far away from their home or
institution and they do not need to wait long for the buses or trains. It
was also found accessibility to public transit is moderate.
Abstract: A biosphere reserve is developed to create harmony
amongst economic development, community development, and
environmental protection, through partnership between human and
nature. Giam Siak Kecil Bukit Batu Biosphere Reserve (GSKBB BR)
in Riau Province, Indonesia, is unique in that it has peat soil
dominating the area, many springs essential for human livelihood,
high biodiversity. Furthermore, it is the only biosphere reserve
covering privately managed production forest areas. In this research, we aimed at analyzing the threat of deforestation
and forest fire, and the potential of CO2 emission at GSKBB BR. We
used Landsat image, arcView software, and ERDAS IMAGINE 8.5
Software to conduct spatial analysis of land cover and land use
changes, calculated CO2 emission based on emission potential from
each land cover and land use type, and exercised simple linear
regression to demonstrate the relation between CO2 emission
potential and deforestation. The result showed that, beside in the buffer zone and transition
area, deforestation also occurred in the core area. Spatial analysis of
land cover and land use changes from years 2010, 2012, and 2014
revealed that there were changes of land cover and land use from
natural forest and industrial plantation forest to other land use types,
such as garden, mixed garden, settlement, paddy fields, burnt areas,
and dry agricultural land. Deforestation in core area, particularly at
the Giam Siak Kecil Wildlife Reserve and Bukit Batu Wildlife
Reserve, occurred in the form of changes from natural forest in to
garden, mixed garden, shrubs, swamp shrubs, dry agricultural land,
open area, and burnt area. In the buffer zone and transition area,
changes also happened, what once swamp forest changed into garden,
mixed garden, open area, shrubs, swamp shrubs, and dry agricultural
land. Spatial analysis on land cover and land use changes indicated
that deforestation rate in the biosphere reserve from 2010 to 2014 had
reached 16 119 ha/year. Beside deforestation, threat toward the
biosphere reserve area also came from forest fire. The occurrence of forest fire in 2014 had burned 101 723 ha of the
area, in which 9 355 ha of core area, and 92 368 ha of buffer zone
and transition area. Deforestation and forest fire had increased CO2
emission as much as 24 903 855 ton/year.
Abstract: Residential block construction of big cities in China
began in the 1950s, and four models had far-reaching influence on
modern residential block in its development process, including unit
compound and residential district in 1950s to 1980s, and gated
community and open community in 1990s to now. Based on analysis
of the four models’ fabric, the article takes residential blocks in
Hangzhou west area as an example and carries on the studies from
urban structure level and block spacial level, mainly including urban
road network, land use, community function, road organization, public
space and building fabric. At last, the article puts forward “Semi-open
Sub-community” strategy to improve the current fabric.
Abstract: Aurèsregion is one of the arid and semi-arid areas that
have suffered climate crises and overexploitation of natural resources
they have led to significant land degradation. The use of remote sensing data allowed us to analyze the land and
its spatiotemporal changes in the Aurès between 1987 and 2013, for
this work, we adopted a method of analysis based on the exploitation
of the images satellite Landsat TM 1987 and Landsat OLI 2013, from
the supervised classification likelihood coupled with field surveys of
the mission of May and September of 2013. Using ENVI EX software by the superposition of the ground cover
maps from 1987 and 2013, one can extract a spatial map change of
different land cover units. The results show that between 1987 and
2013 vegetation has suffered negative changes are the significant
degradation of forests and steppe rangelands, and sandy soils and
bare land recorded a considerable increase. The spatial change map land cover units between 1987 and 2013
allows us to understand the extensive or regressive orientation of
vegetation and soil, this map shows that dense forests give his place
to clear forests and steppe vegetation develops from a degraded forest
vegetation and bare, sandy soils earn big steppe surfaces that explain
its remarkable extension.
The analysis of remote sensing data highlights the profound
changes in our environment over time and quantitative monitoring of
the risk of desertification.
Abstract: Land Use Land Cover (LULC) changes due to human
activities and natural causes have become a major environmental
concern. Assessment of temporal remote sensing data provides
information about LULC impacts on environment. Land Surface
Temperature (LST) is one of the important components for modeling
environmental changes in climatological, hydrological, and
agricultural studies. In this study, LULC changes (September 7, 1984
and July 8, 2014) especially in agricultural lands together with
population changes (1985-2014) and LST status were investigated
using remotely sensed and census data in South Marmara Watershed,
Turkey. LULC changes were determined using Landsat TM and
Landsat OLI data acquired in 1984 and 2014 summers. Six-band TM
and OLI images were classified using supervised classification
method to prepare LULC map including five classes including Forest
(F), Grazing Land (G), Agricultural Land (A), Water Surface (W),
Residential Area-Bare Soil (R-B) classes. The LST image was also
derived from thermal bands of the same dates.
LULC classification results showed that forest areas, agricultural
lands, water surfaces and residential area-bare soils were increased as
65751 ha, 20163 ha, 1924 ha and 20462 ha respectively. In
comparison, a dramatic decrement occurred in grazing land (107985
ha) within three decades. The population increased 29% between
years 1984-2014 in whole study area. Along with the natural causes,
migration also caused this increase since the study area has an
important employment potential. LULC was transformed among the
classes due to the expansion in residential, commercial and industrial
areas as well as political decisions. In the study, results showed that
agricultural lands around the settlement areas transformed to
residential areas in 30 years.
The LST images showed that mean temperatures were ranged
between 26-32°C in 1984 and 27-33°C in 2014. Minimum
temperature of agricultural lands was increased 3°C and reached to
23°C. In contrast, maximum temperature of A class decreased to
41°C from 44°C. Considering temperatures of the 2014 R-B class and
1984 status of same areas, it was seen that mean, min and max
temperatures increased by 2°C.
As a result, the dynamism of population, LULC and LST resulted
in increasing mean and maximum surface temperatures, living
spaces/industrial areas and agricultural lands.
Abstract: Construction and reconstruction of settlements and
individual municipalities, environmental management and the
creation, deployment of the forces of production and building
transport and technical equipment requires a large expenditure of
material and human resources. That is why the economic aspects of
the majority decision in these planes built in the foreground and are
often decisive. Thereby but more serious is that the economic aspects
of the settlement, the creation and function remain in their whole,
unprocessed, and cannot speak of a set of individual techniques and
methods traditional indicators and experiments with new approaches.
This is true both at the level of the national economy, and in their
own urban designs. Still a few remain identified specific economic
shaping patterns of settlement and the less it is possible to speak of
their control. Also practical assessing economics of specific solutions
are often used non-apt indicators in addition to economics usually
identifies with the lowest acquisition cost or high-intensity land use
with little regard for functional efficiency and little studied much
higher operating and maintenance costs".
Abstract: In present study, it was aimed to determine potential
agricultural lands (PALs) in Gokceada (Imroz) Island of Canakkale
province, Turkey. Seven-band Landsat 8 OLI images acquired on
July 12 and August 13, 2013, and their 14-band combination image
were used to identify current Land Use Land Cover (LULC) status.
Principal Component Analysis (PCA) was applied to three Landsat
datasets in order to reduce the correlation between the bands. A total
of six Original and PCA images were classified using supervised
classification method to obtain the LULC maps including 6 main
classes (“Forest”, “Agriculture”, “Water Surface”, “Residential Area-
Bare Soil”, “Reforestation” and “Other”). Accuracy assessment was
performed by checking the accuracy of 120 randomized points for
each LULC maps. The best overall accuracy and Kappa statistic
values (90.83%, 0.8791% respectively) were found for PCA images
which were generated from 14-bands combined images called 3-
B/JA.
Digital Elevation Model (DEM) with 15 m spatial resolution
(ASTER) was used to consider topographical characteristics. Soil
properties were obtained by digitizing 1:25000 scaled soil maps of
Rural Services Directorate General. Potential Agricultural Lands
(PALs) were determined using Geographic information Systems
(GIS). Procedure was applied considering that “Other” class of
LULC map may be used for agricultural purposes in the future
properties. Overlaying analysis was conducted using Slope (S), Land
Use Capability Class (LUCC), Other Soil Properties (OSP) and Land
Use Capability Sub-Class (SUBC) properties.
A total of 901.62 ha areas within “Other” class (15798.2 ha) of
LULC map were determined as PALs. These lands were ranked as
“Very Suitable”, “Suitable”, “Moderate Suitable” and “Low
Suitable”. It was determined that the 8.03 ha were classified as “Very
Suitable” while 18.59 ha as suitable and 11.44 ha as “Moderate
Suitable” for PALs. In addition, 756.56 ha were found to be “Low
Suitable”. The results obtained from this preliminary study can serve
as basis for further studies.
Abstract: Due to rapid pressured of population growth, city has
started to lose its old tradition. City becomes congested with
uncomfortably living. Urban renewal refers orderly development of
settlements as well as land redevelopment. For this paper Chittagong
city has been selected as study area. It had a great tradition but it has
been losing its concord. Land use pattern of this place is also
haphazard due to lack of planning intervention. Renewal plan is
needed to ascertain suitable redevelopment and to recommend on
preservation of city heritage structure. The goal of this study is to
prepare a renewal plan using local planning approach. Social impact
methods have been used to achieve this goal. Both primary and
secondary data are used to achieve the goal. This study may find out
a complete solution for healthy living in old Part of city. This study
will help to preserve its tradition and makes urban lives more livable.
Abstract: Soil quality monitoring is a science-based soil
management tool that assesses soil ecosystem health.
A soil monitoring program in Auckland, New Zealand’s largest
city extends from 1995 to the present. The objective of this study was
to firstly determine changes in soil parameters (basic soil properties
and heavy metals) that were assessed from rural land in 1995-2000
and repeated in 2008-2012. The second objective was to determine
differences in soil parameters across various land uses including
native bush, rural (horticulture, pasture and plantation forestry) and
urban land uses using soil data collected in more recent years (2009-
2013).
Across rural land, mean concentrations of Olsen P had
significantly increased in the second sampling period and was
identified as the indicator of most concern, followed by soil
macroporosity, particularly for horticultural and pastoral land. Mean
concentrations of Cd were also greatest for pastoral and horticultural
land and a positive correlation existed between these two parameters,
which highlights the importance of analysing basic soil parameters in
conjunction with heavy metals. In contrast, mean concentrations of
As, Cr, Pb, Ni and Zn were greatest for urban sites. Native bush sites
had the lowest concentrations of heavy metals and were used to
calculate a ‘pollution index’ (PI). The mean PI was classified as high
(PI > 3) for Cd and Ni and moderate for Pb, Zn, Cr, Cu, As and Hg,
indicating high levels of heavy metal pollution across both rural and
urban soils. From a land use perspective, the mean ‘integrated
pollution index’ was highest for urban sites at 2.9 followed by
pasture, horticulture and plantation forests at 2.7, 2.6 and 0.9,
respectively.
It is recommended that soil sampling continues over time because
a longer spanning record will allow further identification of where
soil problems exist and where resources need to be targeted in the
future. Findings from this study will also inform policy and science
direction in regional councils.