Abstract: A numerical study of natural convection heat transfer
in water filled cavity has been examined in 3-Dfor single phase liquid
cooling system by using an array of parallel plate fins mounted to one
wall of a cavity. The heat generated by a heat source represents a
computer CPU with dimensions of 37.5∗37.5mm mounted on
substrate. A cold plate is used as a heat sink installed on the opposite
vertical end of the enclosure. The air flow inside the computer case is
created by an exhaust fan. A turbulent air flow is assumed and k-ε
model is applied. The fins are installed on the substrate to enhance
the heat transfer. The applied power energy range used is between 15
- 40W. In order to determine the thermal behaviour of the cooling
system, the effect of the heat input and the number of the parallel
plate fins are investigated. The results illustrate that as the fin number
increases the maximum heat source temperature decreases. However,
when the fin number increases to critical value the temperature start
to increase due to the fins are too closely spaced and that cause the
obstruction of water flow. The introduction of parallel plate fins
reduces the maximum heat source temperature by 10% compared to
the case without fins. The cooling system maintains the maximum
chip temperature at 64.68°C when the heat input was at 40W that is
much lower than the recommended computer chips limit temperature
of no more than 85°C and hence the performance of the CPU is
enhanced.
Abstract: The aim of present study was to monitor the presence
of Trichodina sp. in Rainbow trout, Oncorhynchus mykiss collected
from various fish farms in the western provinces of Iran during
January, 2013- January, 2014. Out of 675 sampled fish 335, (49.16%)
were infested with Trichodina. The highest prevalence was observed
in the spring and winter followed by autumn and summer. In general,
the intensity of infection was low except in cases where outbreaks of
Trichodiniasis endangered the survival of fish in some ponds. In light
infestation Trichodina is usually present on gills, fins and skin of
apparently healthy fish. Clinical signs of Trichodiniasis only appear
on fish with heavy infections and cases of moderate ones that are
usually exposed to one or more stress factors including, rough
handling during transportation from ponds, overcrowdness,
malnutrition, high of free ammonia and low of oxygen concentration.
Clinical signs of Trichodiniasis in sampled fish were sluggish
movement, loss of appetite, black coloration, necrosis and ulcer on
different parts of the body, detached scales and excessive
accumulation of mucous in gill pouches. The most obvious
histopathological changes in diseased fish were sloughing of the
epidermal layer, aggregation of leucocytes and melanine-carrying
cells (between the dermis and hypodermis) and proliferative changes
including hyperplasia and hypertrophy of the epithelial lining cells of
gill filaments which resulted in fusion of secondary lamellae. Control
of Trichodiniasis, has been achieved by formalin bath treatment at a
concentration of 250 ppm for one hour.
Abstract: Polyethylene (PE), Polypropylene (PP), Polyethylene
(vinyl acetate) (EVA) and PE-ionomer nanocomposite samples were
prepared by mixing of the polymer with organofilized
montmorillonite fillers Cloisite 93A and Dellite 67G. The amount of
each modified montmorillonite (MMT) was fixed to 5% (w/w). The
twin-screw kneader was used for the compounding of polymer matrix
and chosen nanofillers. The level of MMT exfoliation was studied by
the transmission electron microscopy (TEM) observations. The
mechanical properties of prepared materials were evaluated by
dynamical mechanical analysis at 30°C and by the measurement of
tensile properties (stress and strain at break).
Abstract: This study applies the inverse method and three- dimensional CFD commercial software in conjunction with the experimental temperature data to investigate the heat transfer and fluid flow characteristics of the plate-fin heat sink in a closed rectangular enclosure for various values of fin height. The inverse method with the finite difference method and the experimental temperature data is applied to determine the heat transfer coefficient. The k-ε turbulence model is used to obtain the heat transfer and fluid flow characteristics within the fins. To validate the accuracy of the results obtained, the comparison of the average heat transfer coefficient is made. The calculated temperature at selected measurement locations on the plate-fin is also compared with experimental data.
Abstract: Finned-tube heat exchangers are predominantly used in space conditioning systems, as well as other applications requiring heat exchange between two fluids. The design of finned-tube heat exchangers requires the selection of over a dozen design parameters by the designer such as tube pitch, tube diameter, tube thickness, etc… Finned-tube heat exchangers are common devices; however, their performance characteristics are complicated. In this paper numerical studies have been carried out to analyze the performances of finned tube heat exchanger (without fins considered for experimental purpose) by predicting the characteristics of temperature difference and pressure drop. In this study, a design considering 5 design variables and also maximizing the temperature difference and pressure drop was suggested by applying DOE. During this process, L18 orthogonal array was adopted. Parametric analytical studies have been carried out using ANOVA to determine the relative importance of each variable with respect to the temperature difference and the pressure drop. Following the results, the final design was suggested by predicting the optimum design therefore confirming the optimized condition.
Abstract: In this study, heat release performances of the three extruded-type heat sinks can be used in inverter for solar power generation were evaluated. Numbers of fins in the heat sinks (namely E-38, E-47 and E-76) were 38, 47 and 76, respectively. Heat transfer areas of them were 1.8, 1.9 and 2.8m2. The heat release performances of E-38, E-47 and E-76 heat sinks were measured as 79.6, 81.6 and 83.2%, respectively. The results of heat release performance show that the larger amount of heat transfer area the higher heat release rate. While on the other, in this experiment, variations of mass flow rates caused by different cross sectional areas of the three heat sinks may not be the major parameter of the heat release. Despite the 47.4% increment of heat transfer area of E-76 heat sink than that of E-47 one, its heat release rate was higher by only 2.0%; this suggests that its heat transfer area need to be optimized.
Abstract: This article deals with numerical simulation of the
floor heating convector in 3D. Numerical simulation is focused on
cooling mode of the floor heating convector. Geometrical model
represents section of the heat exchanger – two fins with the gap
between, pipes are not involved. Two types of fin are examined –
sinusoidal and angular shape with different fin spacing. Results of fin
spacing in case of constant Reynolds number are presented. For the
numerical simulation was used commercial software Ansys Fluent.
Abstract: This study investigated morphology of the Spanner Barb (Puntius lateristriga Valenciennes, 1842) and water quality at Thepchana waterfall. This study was conducted at Thepchana Waterfall, Khao Nan National Park from March to May 2007. There were 40 Spanner Barb collected with 20 males and 20 females. Males had an average of 5.57 cm in standard length, 6.62 cm in total length and 5.18 g in total body weight. Females had an average of 7.25 cm in standard length, 8.24 cm in total length and 10.96 g in total body weight. The length (L) – weight (W) relationships for combining sexes, males and females were LogW = -2.137 + 3.355logL, log W = -0.068 + 3.297logL, and log W = -2.068 + 3.297logL, respectively. The Spanner Barb were smaller size fish with a compressed form; terminal mouth; villiform teeth; ctenoid scale; concave tail; general body color yellowish olive, with slight reddish tint to fins; vertical band beginning below dorsal and horizontal stripe from base of tail almost to vertical band. They also had a vertical band midway between the eye and first vertical band. There was a black spot above anal fin. The bladder looked like J-shape. Inside of the bladder was found small insects and insect lava. The body length and the bowels length was 1:1 ratio. The water temperature ranged from 25.00 – 27.00 °C which was appropriate for their habitat characteristics. Acid - alkalinity ranged from 6.65 – 6.90 mg/l. Dissolved oxygen ranged from 4.55 – 4.70 mg/l. Water hardness ranged from 31.00 – 48.00 mg/l. The amount of ammonia was about 0.25 mg/l.
Abstract: A numerical investigation has carried out to understand the melting characteristics of phase change material (PCM) in a fin type latent heat storage with the addition of embedded aluminum spiral fillers. It is known that melting performance of PCM can be significantly improved by increasing the number of embedded metallic fins in the latent heat storage system but to certain values where only lead to small improvement in heat transfer rate. Hence, adding aluminum spiral fillers within the fin gap can be an option to improve heat transfer internally. This paper presents extensive computational visualizations on the PCM melting patterns of the proposed fin-spiral fillers configuration. The aim of this investigation is to understand the PCM-s melting behaviors by observing the natural convection currents movement and melting fronts formation. Fluent 6.3 simulation software was utilized in producing twodimensional visualizations of melting fractions, temperature distributions and flow fields to illustrate the melting process internally. The results show that adding aluminum spiral fillers in Fin type latent heat storage can promoted small but more active natural convection currents and improve melting of PCM.
Abstract: The pigments covered by film-forming polymers have
opened a prospect to improve the quality of water-based printing
inks. In this study such pigments were prepared by the initiated
polymerization of styrene and methacrylate derivative monomers in
the aqueous pigment dispersions. The formation of polymer films
covering pigment cores depends on the polymerization time and the
ratio of pigment to monomers. At the time of 4 hours and the ratio of
1/10 almost pigment particles are coated by the polymer. The formed
polymer covers of pigments have the average thickness of 5.95 nm.
The size increasing percentage of the coated particles after a week is
4.5 %, about fourteen-fold lower than of the original ones. The
obtained results indicate that the coated pigments are improved
dispersion stability in water medium along with a guarantee for the
optical colour.
Abstract: The forced convection heat transfer in high porosity metal-foam filled tube heat exchangers are studied in this paper. The Brinkman Darcy momentum model and two energy equations for both solid and fluid phases in porous media are employed .The study shows that using metal-foams can significantly improve the heat transfer in heat exchangers.
Abstract: Pyrolysis of waste tire is one of alternative technique
to produce petrochemicals, such as light olefins, mixed C4, and monoaromatics.
Noble metals supported on acid zeolite catalysts were
reported as potential catalysts to produce the high valuable products
from waste tire pyrolysis. Especially, Pd supported on HBeta gave a
high yield of olefins, mixed C4, and mono-aromatics. Due to the high
prices of noble metals, the objective of this work was to investigate
whether or not a non-noble Ni metal can be used as a substitute of a
noble metal, Pd, supported on HBeta as a catalyst for waste tire pyrolysis.
Ni metal was selected in this work because Ni has high activity
in cracking, isomerization, hydrogenation and the ring opening of
hydrocarbons Moreover, Ni is an element in the same group as Pd
noble metal, which is VIIIB group, aiming to produce high valuable
products similarly obtained from Pd. The amount of Ni was varied as
5, 10, and 20% by weight, for comparison with a fixed 1 wt% Pd,
using incipient wetness impregnation. The results showed that as a
petrochemical-producing catalyst, 10%Ni/HBeta performed better
than 1%Pd/HBeta because it did not only produce the highest yield of
olefins and cooking gases, but the yields were also higher than
1%Pd/HBeta. 5%Ni/HBeta can be used as a substitute of
1%Pd/HBeta for similar crude production because its crude contains
the similar amounts of naphtha and saturated HCs, although it gave
no concentration of light mono-aromatics (C6-C11) in the oil. Additionally,
10%Ni/HBeta that gave high olefins and cooking gases was
found to give a fairly high concentration of the light mono-aromatics
in the oil.
Abstract: This article deals with the numerical simulation of the
floor heating convector in 3D. Presented convector can operate in
two modes – cooling mode and heating mode. This initial numerical
simulation is focused on cooling mode of the convector. Models with
different temperature of the fins are compared and three various
shapes of the fins are examined as well. The objective of the work is
to predict air flow and heat transfer inside convector for further
optimalization of these devices. For the numerical simulation was
used commercial software Ansys Fluent.
Abstract: This paper presents the analysis of duct design using
static and dynamic approaches. The static approach is used to find
out applicability between the design and material applied. The
material used in this paper is Thermoplastic Olefins (TPO). For the
dynamic approach, the focusing is only on the CFD simulations. The
fatigue life in this design and material applied also covered.
Abstract: At very high speeds, bubbles form in the underwater vehicles because of sharp trailing edges or of places where the local pressure is lower than the vapor pressure. These bubbles are called cavities and the size of the cavities grows as the velocity increases. A properly designed cavitator can induce the formation of a single big cavity all over the vehicle. Such a vehicle travelling in the vaporous cavity is called a supercavitating vehicle and the present research work mainly focuses on the dynamic modeling of such vehicles. Cavitation of the fins is also accounted and the effect of the same on trajectory is well explained. The entire dynamics has been developed using the state space approach and emphasis is given on the effect of size and angle of attack of the cavitator. Control law has been established for the motion of the vehicle using Non-linear Dynamic Inverse (NDI) with cavitator as the control surface.
Abstract: The counter flow solar air heaters, with four
transverse fins and wire mesh layers are constructed and investigated
experimentally for thermal efficiency at a geographic location of
Cyprus in the city of Famagusta. The absorber plate is replaced by
sixteen steel wire mesh layers, 0.18 x 0.18cm in cross section
opening and a 0.02cm in diameter. The wire mesh layers arranged in
three groups, first and second include 6 layers, while the third include
4 layers. All layers fixed in the duct parallel to the glazing and each
group separated from the others by wood frame thickness of 0.5cm to
reduce the pressure drop. The transverse fins arranged in a way to
force the air to flow through the bed like eight letter path with flow
depth 3cm. The proposed design has increased the heat transfer rate,
but on other hand causes a high pressure drop. The obtained results
show that, for air mass flow rate range between 0.011-0.036kg/s, the
thermal efficiency increases with increasing the air mass flow. The
maximum efficiency obtained is 65.6% for the mass flow rate of
0.036kg/s. Moreover, the temperature difference between the outlet
flow and the ambient temperature, ΔT, reduces as the air mass flow
rate increase. The maximum difference between the outlet and
ambient temperature obtained was 43°C for double pass for minimum
mass flow rate of 0.011kg/s. Comparison with a conventional solar
air heater collector shows a significantly development in the thermal
efficiency.
Abstract: The purpose of this study is to investigate the
efficiency of a double-layer roof in collecting solar energy as an
application to the areas such as raising high-end temperature of
organic Rankine cycle (ORC). The by-product of the solar roof is to
reduce building air-conditioning loads. The experimental apparatus
are arranged to evaluate the effects of the solar roof in absorbing solar
energy. The flow channel is basically formed by an aluminum plate on
top of a plywood plate. The geometric configurations in which the
effects of absorbing energy is analyzed include: a bare uncovered
aluminum plate, a glass-covered aluminum plate, a
glass-covered/black-painted aluminum plate, a plate with variable
lengths, a flow channel with stuffed material (in an attempt on
enhancement of heat conduction), and a flow channel with variable
slanted angles. The experimental results show that the efficiency of
energy collection varies from 0.6 % to 11 % for the geometric
configurations mentioned above. An additional study is carried out
using CFD simulation to investigate the effects of fins on the
aluminum plate. It shows that due to vastly enhanced heat conduction,
the efficiency can reach ~23 % if 50 fins are installed on the aluminum
plate. The study shows that a double-layer roof can efficiently absorb
solar energy and substantially reduce building air-conditioning
loads. On the high end of an organic Rankine cycle, a solar pond is
used to replace the warm surface water of the sea as OTEC (ocean
thermal energy conversion) is the driving energy for the ORC. The
energy collected from the double-layered solar roof can be pumped
into the pond and raise the pond temperature as the pond surface area is
equivalently increased by nearly one-fourth of the total area of the
double-layer solar roof. The effect of raising solar pond temperature is
especially prominent if the double-layer solar roofs are installed in a
community area.
Abstract: Hydrothermally synthesized high silica borosilicates
with the MFI structure was subjected to several characterization
techniques. The effect of boron on the structure and acidity of
HZSM-5 catalyst were studied by XRD, SEM, N2 adsorption, solid
state NMR, NH3-TPD. It was confirmed that boron had entered the
framework in the boron samples. The results also revealed that strong
acidity was weakened and weak acidity was strengthened by the
boron added zeolite framework compared with parent catalyst. The
catalytic performance was carried out in a fixed bed at 460°C for
methanol to propylene (MTP) reaction. The results of MTP reaction
showed a great increment of the propylene selectivity and excellent
stability for the B-HZSM-5. The catalyst exhibited about 81%
selectivity to C2
= - C4
= olefins with 40% selectivity of propylene as
major component at near 100% methanol conversion, and the stable
performance in the studied period was 100h.
Abstract: A new design of a planar passive T-micromixer with fin-shaped baffles in the mixing channel is presented. The mixing efficiency and the level of pressure loss in the channel have been investigated by numerical simulations in the range of Reynolds number (Re) 1 to 50. A Mixing index (Mi) has been defined to quantify the mixing efficiency, which results over 85% at both ends of the Re range, what demonstrates the micromixer can enhance mixing using the mechanisms of diffusion (lower Re) and convection (higher Re). Three geometric dimensions: radius of baffle, baffles pitch and height of the channel define the design parameters, and the mixing index and pressure loss are the performance parameters used to optimize the micromixer geometry with a multi-criteria optimization method. The Pareto front of designs with the optimum trade-offs, maximum mixing index with minimum pressure loss, is obtained. Experiments for qualitative and quantitative validation have been implemented.
Abstract: A novel methodology has been used to design an
evaporator coil of a refrigerant. The methodology used is through a
complete Computer Aided Design /Computer Aided Engineering
approach, by means of a Computational Fluid Dynamic/Finite
Element Analysis model which is executed many times for the
thermal-fluid exploration of several designs' configuration by an
commercial optimizer. Hence the design is carried out automatically
by parallel computations, with an optimization package taking the
decisions rather than the design engineer. The engineer instead takes
decision regarding the physical settings and initializing of the
computational models to employ, the number and the extension of the
geometrical parameters of the coil fins and the optimization tools to
be employed. The final design of the coil geometry found to be better
than the initial design.