Abstract: Chua’s circuit is one of the most important electronic devices that are used for Chaos and Bifurcation studies. A central role of secure communication is devoted to it. Since the adaptive control is used vastly in the linear systems control, here we introduce a new trend of application of adaptive method in the chaos controlling field. In this paper, we try to derive a new adaptive control scheme for Chua’s circuit controlling because control of chaos is often very important in practical operations. The novelty of this approach is for sake of its robustness against the external perturbations which is simulated as an additive noise in all measured states and can be generalized to other chaotic systems. Our approach is based on Lyapunov analysis and the adaptation law is considered for the feedback gain. Because of this, we have named it NAFT (Nonlinear Adaptive Feedback Technique). At last, simulations show the capability of the presented technique for Chua’s circuit.
Abstract: Moisture is an important consideration in many
aspects ranging from irrigation, soil chemistry, golf course, corrosion
and erosion, road conditions, weather predictions, livestock feed
moisture levels, water seepage etc. Vegetation and crops always
depend more on the moisture available at the root level than on
precipitation occurrence. In this paper, design of an instrument is
discussed which tells about the variation in the moisture contents of
soil. This is done by measuring the amount of water content in soil by
finding the variation in capacitance of soil with the help of a
capacitive sensor. The greatest advantage of soil moisture sensor is
reduced water consumption. The sensor is also be used to set lower
and upper threshold to maintain optimum soil moisture saturation and
minimize water wilting, contributes to deeper plant root growth
,reduced soil run off /leaching and less favorable condition for insects
and fungal diseases. Capacitance method is preferred because, it
provides absolute amount of water content and also measures water
content at any depth.
Abstract: In this paper, we are interested in attitude control of a satellite, which using wheels of reaction, by state feedback. First, we develop a method allowing us to put the control and its integral in the state-feedback form. Then, by using the theorem of Gronwall- Bellman, we put the sufficient conditions so that the nonlinear system modeling the satellite is stabilisable and observed by state feedback.
Abstract: In this paper, novel techniques in increasing the accuracy
and speed of convergence of a Feed forward Back propagation
Artificial Neural Network (FFBPNN) with polynomial activation
function reported in literature is presented. These technique was
subsequently used to determine the coefficients of Autoregressive
Moving Average (ARMA) and Autoregressive (AR) system. The
results obtained by introducing sequential and batch method of weight
initialization, batch method of weight and coefficient update, adaptive
momentum and learning rate technique gives more accurate result
and significant reduction in convergence time when compared t the
traditional method of back propagation algorithm, thereby making
FFBPNN an appropriate technique for online ARMA coefficient
determination.
Abstract: Solidification cracking and hydrogen cracking are some defects generated in the fusion welding of ultrahigh carbon steels. However, friction stir welding (FSW) of such steels, being a solid-state technique, has been demonstrated to alleviate such problems encountered in traditional welding. FSW include different process parameters that must be carefully defined prior processing. These parameters included but not restricted to: tool feed, tool RPM, tool geometry, tool tilt angle. These parameters form a key factor behind avoiding warm holes and voids behind the tool and in achieving a defect-free weld. More importantly, these parameters directly affect the microstructure of the weld and hence the final mechanical properties of weld. For that, 3D finite element (FE) thermo-mechanical model was developed using DEFORM 3D to simulate FSW of carbon steel. At points of interest in the joint, tracking is done for history of critical state variables such as temperature, stresses, and strain rates. Typical results found include the ability to simulate different weld zones. Simulations predictions were successfully compared to experimental FSW tests. It is believed that such a numerical model can be used to optimize FSW processing parameters to favor desirable defect free weld with better mechanical properties.
Abstract: Deep cold rolling (DCR) and low plasticity burnishing (LPB) process are cold working processes, which easily produce a smooth and work-hardened surface by plastic deformation of surface irregularities. The present study focuses on the surface roughness and surface hardness aspects of AISI 4140 work material, using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in order to identify the predominant factors amongst the selected parameters. They were then categorized in order of significance followed by setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. In the present work, the influence of main process parameters (force, feed rate, number of tool passes/overruns, initial roughness of the work piece, ball material, ball diameter and lubricant used) on the surface roughness and the hardness of AISI 4140 steel were studied for both LPB and DCR process and the results are compared. It was observed that by using LPB process surface hardness has been improved by 167% and in DCR process surface hardness has been improved by 442%. It was also found that the force, ball diameter, number of tool passes and initial roughness of the workpiece are the most pronounced parameters, which has a significant effect on the work piece-s surface during deep cold rolling and low plasticity burnishing process.
Abstract: The effect of cassava root ensiled with cassava top or
legumes on voluntary feed intake and milk production were
determined in 12 dairy cows using a 4×3 change-over design.
Experimental period were 30 days long and consisted of 14 days of
adaptation. Silage was prepared from cassava root mixed with
cassava top or legumes at ratio 60:40. Cows were allotted at random
to receive ad libitum one of four rations: T1) control, T2) cassava
root +cassava top-silages, T3) cassava root +hamata - silages and T4)
cassava root +Thapra stylo-silages.
The dry matter intake (BW0.75) was higher (P< 0.05) in cow fed
with silages diets compared with T1. However, the intake of T2 was
higher among treatments. Milk production was lowest in cow fed
with T1. Among silages based diets, milk production was not
significantly different but 4%FCM was higher in cow fed T2. Milk
compositions were not affected by feeding diets.
It is concluded that feeding cassava root ensiled with its leaves as
a supplement increased dry matter intake and significantly improved
4%FCM. The combination of cassava root and legume silages did not
improve the feed intake but did increase the milk production.
Abstract: Interactive public displays give access as an
innovative media to promote enhanced communication between
people and information. However, digital public displays are subject
to a few constraints, such as content presentation. Content
presentation needs to be developed to be more interesting to attract
people’s attention and motivate people to interact with the display. In
this paper, we proposed idea to implement contents with interaction
elements for vision-based digital public display. Vision-based
techniques are applied as a sensor to detect passers-by and theme
contents are suggested to attract their attention for encouraging them
to interact with the announcement content. Virtual object, gesture
detection and projection installation are applied for attracting
attention from passers-by. Preliminary study showed positive
feedback of interactive content designing towards the public display.
This new trend would be a valuable innovation as delivery of
announcement content and information communication through this
media is proven to be more engaging.
Abstract: This paper presents the exergy analysis of a
desalination unit using humidification-dehumidification process.
Here, this unit is considered as a thermal system with three main
components, which are the heating unit by using a solar collector, the
evaporator or the humidifier, and the condenser or the dehumidifier.
In these components the exergy is a measure of the quality or grade
of energy and it can be destroyed in them. According to the second
law of thermodynamics this destroyed part is due to irreversibilities
which must be determined to obtain the exergetic efficiency of the
system.
In the current paper a computer program has been developed using
visual basic to determine the exergy destruction and the exergetic
efficiencies of the components of the desalination unit at variable
operation conditions such as feed water temperature, outlet air
temperature, air to feed water mass ratio and salinity, in addition to
cooling water mass flow rate and inlet temperature, as well as
quantity of solar irradiance.
The results obtained indicate that the exergy efficiency of the
humidifier increases by increasing the mass ratio and decreasing the
outlet air temperature. In the other hand the exergy efficiency of the
condenser increases with the increase of this ratio and also with the
increase of the outlet air temperature.
Abstract: Sediment formation and its transport along the river course is considered as important hydraulic consideration in river engineering. Their impact on the morphology of rivers on one hand and important considerations of which in the design and construction of the hydraulic structures on the other has attracted the attention of experts in arid and semi-arid regions. Under certain conditions where the momentum energy of the flow stream reaches a specific rate, the sediment materials start to be transported with the flow. This can usually be analyzed in two different categories of suspended and bed load materials. Sedimentation phenomenon along the waterways and the conveyance of vast volume of materials into the canal networks can potentially influence water abstraction in the intake structures. This can pose a serious threat to operational sustainability and water delivery performance in the canal networks. The situation is serious where ineffective watershed management (poor vegetation cover in the water basin) is the underlying cause of soil erosion which feeds the materials into the waterways that intern would necessitate comprehensive study. The present paper aims to present an analytical investigation of the sediment process in the waterways on one hand and estimation of the sediment load transport into the lined canals using the SHARC software on the other. For this reason, the paper focuses on the comparative analysis of the hydraulic behaviors of the Sabilli main canal that feeds the pumping station with that of the Western canal in the Greater Dezful region to identify effective factors in sedimentation and ways of mitigating their impact on water abstraction in the canal systems. The method involved use of observational data available in the Dezful Dastmashoon hydrometric station along a 6 km waterway of the Sabilli main canal using the SHARC software to estimate the suspended load concentration and bed load materials. Results showed the transport of a significant volume of sediment loads from the waterways into the canal system which is assumed to have arisen from the absence of stilling basin on one hand and the gravity flow on the other has caused serious challenges. This is contrary to what occurs in the Sabilli canal, where the design feature which incorporates a settling basin just before the pumping station is the major cause of reduced sediment load transport into the canal system.Results showed that modification of the present design features by constructing a settling basin just upstream of the western intake structure can considerably reduce the entry of sediment materials into the canal system. Not only this can result in the sustainability of the hydraulic structures but can also improve operational performance of water conveyance and distribution system, all of which are the pre-requisite to secure reliable and equitable water delivery regime for the command area.
Abstract: This paper addresses the problems encountered by conventional distance relays when protecting double-circuit transmission lines. The problems arise principally as a result of the mutual coupling between the two circuits under different fault conditions; this mutual coupling is highly nonlinear in nature. An adaptive protection scheme is proposed for such lines based on application of artificial neural network (ANN). ANN has the ability to classify the nonlinear relationship between measured signals by identifying different patterns of the associated signals. One of the key points of the present work is that only current signals measured at local end have been used to detect and classify the faults in the double circuit transmission line with double end infeed. The adaptive protection scheme is tested under a specific fault type, but varying fault location, fault resistance, fault inception angle and with remote end infeed. An improved performance is experienced once the neural network is trained adequately, which performs precisely when faced with different system parameters and conditions. The entire test results clearly show that the fault is detected and classified within a quarter cycle; thus the proposed adaptive protection technique is well suited for double circuit transmission line fault detection & classification. Results of performance studies show that the proposed neural network-based module can improve the performance of conventional fault selection algorithms.
Abstract: In recent years, rapid advances in software and hardware in the field of information technology along with a digital imaging revolution in the medical domain facilitate the generation and storage of large collections of images by hospitals and clinics. To search these large image collections effectively and efficiently poses significant technical challenges, and it raises the necessity of constructing intelligent retrieval systems. Content-based Image Retrieval (CBIR) consists of retrieving the most visually similar images to a given query image from a database of images[5]. Medical CBIR (content-based image retrieval) applications pose unique challenges but at the same time offer many new opportunities. On one hand, while one can easily understand news or sports videos, a medical image is often completely incomprehensible to untrained eyes.
Abstract: A mathematical model of the surface roughness
has been developed by using response surface methodology
(RSM) in grinding of AISI D2 cold work tool steels. Analysis
of variance (ANOVA) was used to check the validity of the
model. Low and high value for work speed and feed rate are
decided from design of experiment. The influences of all
machining parameters on surface roughness have been
analyzed based on the developed mathematical model. The
developed prediction equation shows that both the feed rate
and work speed are the most important factor that influences
the surface roughness. The surface roughness was found to be
the lowers with the used of low feed rate and low work speed.
Accuracy of the best model was proved with the testing data.
Abstract: The importance of machining process in today-s
industry requires the establishment of more practical approaches to
clearly represent the intimate and severe contact on the tool-chipworkpiece
interfaces. Mathematical models are developed using the
measured force signals to relate each of the tool-chip friction
components on the rake face to the operating cutting parameters in
rough turning operation using multilayers coated carbide inserts.
Nonlinear modeling proved to have high capability to detect the
nonlinear functional variability embedded in the experimental data.
While feedrate is found to be the most influential parameter on the
friction coefficient and its related force components, both cutting
speed and depth of cut are found to have slight influence. Greater
deformed chip thickness is found to lower the value of friction
coefficient as the sliding length on the tool-chip interface is reduced.
Abstract: This paper reports the tensile fracture location
characterizations of dissimilar friction stir welds between 5754
aluminium alloy and C11000 copper. The welds were produced using
three shoulder diameter tools; namely, 15, 18 and 25 mm by varying
the process parameters. The rotational speeds considered were 600,
950 and 1200 rpm while the feed rates employed were 50, 150 and
300 mm/min to represent the low, medium and high settings
respectively. The tensile fracture locations were evaluated using the
optical microscope to identify the fracture locations and were
characterized. It was observed that 70% of the tensile samples failed
in the Thermo Mechanically Affected Zone (TMAZ) of copper at the
weld joints. Further evaluation of the fracture surfaces of the pulled
tensile samples revealed that welds with low Ultimate Tensile
Strength either have defects or intermetallics present at their joint
interfaces.
Abstract: Power loss reduction is one of the main targets in power industry and so in this paper, the problem of finding the optimal configuration of a radial distribution system for loss reduction is considered. Optimal reconfiguration involves the selection of the best set of branches to be opened ,one each from each loop, for reducing resistive line losses , and reliving overloads on feeders by shifting the load to adjacent feeders. However ,since there are many candidate switching combinations in the system ,the feeder reconfiguration is a complicated problem. In this paper a new approach is proposed based on a simple optimum loss calculation by determining optimal trees of the given network. From graph theory a distribution network can be represented with a graph that consists a set of nodes and branches. In fact this problem can be viewed as a problem of determining an optimal tree of the graph which simultaneously ensure radial structure of each candidate topology .In this method the refined genetic algorithm is also set up and some improvements of algorithm are made on chromosome coding. In this paper an implementation of the algorithm presented by [7] is applied by modifying in load flow program and a comparison of this method with the proposed method is employed. In [7] an algorithm is proposed that the choice of the switches to be opened is based on simple heuristic rules. This algorithm reduce the number of load flow runs and also reduce the switching combinations to a fewer number and gives the optimum solution. To demonstrate the validity of these methods computer simulations with PSAT and MATLAB programs are carried out on 33-bus test system. The results show that the performance of the proposed method is better than [7] method and also other methods.
Abstract: In the recent past Learning Classifier Systems have
been successfully used for data mining. Learning Classifier System
(LCS) is basically a machine learning technique which combines
evolutionary computing, reinforcement learning, supervised or
unsupervised learning and heuristics to produce adaptive systems. A
LCS learns by interacting with an environment from which it
receives feedback in the form of numerical reward. Learning is
achieved by trying to maximize the amount of reward received. All
LCSs models more or less, comprise four main components; a finite
population of condition–action rules, called classifiers; the
performance component, which governs the interaction with the
environment; the credit assignment component, which distributes the
reward received from the environment to the classifiers accountable
for the rewards obtained; the discovery component, which is
responsible for discovering better rules and improving existing ones
through a genetic algorithm. The concatenate of the production rules
in the LCS form the genotype, and therefore the GA should operate
on a population of classifier systems. This approach is known as the
'Pittsburgh' Classifier Systems. Other LCS that perform their GA at
the rule level within a population are known as 'Mitchigan' Classifier
Systems. The most predominant representation of the discovered
knowledge is the standard production rules (PRs) in the form of IF P
THEN D. The PRs, however, are unable to handle exceptions and do
not exhibit variable precision. The Censored Production Rules
(CPRs), an extension of PRs, were proposed by Michalski and
Winston that exhibit variable precision and supports an efficient
mechanism for handling exceptions. A CPR is an augmented
production rule of the form: IF P THEN D UNLESS C, where
Censor C is an exception to the rule. Such rules are employed in
situations, in which conditional statement IF P THEN D holds
frequently and the assertion C holds rarely. By using a rule of this
type we are free to ignore the exception conditions, when the
resources needed to establish its presence are tight or there is simply
no information available as to whether it holds or not. Thus, the IF P
THEN D part of CPR expresses important information, while the
UNLESS C part acts only as a switch and changes the polarity of D
to ~D. In this paper Pittsburgh style LCSs approach is used for
automated discovery of CPRs. An appropriate encoding scheme is
suggested to represent a chromosome consisting of fixed size set of
CPRs. Suitable genetic operators are designed for the set of CPRs
and individual CPRs and also appropriate fitness function is proposed
that incorporates basic constraints on CPR. Experimental results are
presented to demonstrate the performance of the proposed learning
classifier system.
Abstract: This paper presents a experiment to estimate the
influences of cutting conditions in microstructure changes of
machining austenitic 304 stainless steel, especially for wear insert. The
wear insert were prefabricated with a width of 0.5 mm. And the forces,
temperature distribution, RS, and microstructure changes were
measured by force dynamometer, infrared thermal camera, X-ray
diffraction, XRD, SEM, respectively. The results told that the different
combinations of machining condition have a significant influence on
machined surface microstructure changes. In addition to that, the
ANOVA and AOMwere used to tell the different influences of cutting
speed, feed rate, and wear insert.
Abstract: In this paper, we investigate the study of techniques
for scheduling users for resource allocation in the case of multiple
input and multiple output (MIMO) packet transmission systems. In
these systems, transmit antennas are assigned to one user or
dynamically to different users using spatial multiplexing. The
allocation of all transmit antennas to one user cannot take full
advantages of multi-user diversity. Therefore, we developed the case
when resources are allocated dynamically. At each time slot users
have to feed back their channel information on an uplink feedback
channel. Channel information considered available in the schedulers
is the zero forcing (ZF) post detection signal to interference plus
noise ratio. Our analysis study concerns the round robin and the
opportunistic schemes.
In this paper, we present an overview and a complete capacity
analysis of these schemes. The main results in our study are to give
an analytical form of system capacity using the ZF receiver at the
user terminal. Simulations have been carried out to validate all
proposed analytical solutions and to compare the performance of
these schemes.
Abstract: Feeder is one of the airships of the Multibody Advanced Airship for Transport (MAAT) system, under development within the EU FP7 project. MAAT is based on a modular concept composed of two different parts that have the possibility to join; respectively they are the so-called Cruiser and Feeder, designed on the lighter than air principle. Feeder, also named ATEN (Airship Transport Elevator Network), is the smaller one which joins the bigger one, Cruiser, also named PTAH (Photovoltaic modular Transport Airship for High altitude),envisaged to happen at 15km altitude. During the MAAT design phase, the aerodynamic studies of the both airships and their interactions are analyzed. The objective of these studies is to understand the aerodynamic behavior of all the preselected configurations, as an important element in the overall MAAT system design. The most of these configurations are only simulated by CFD, while the most feasible one is experimentally analyzed in order to validate and thrust the CFD predictions. This paper presents the numerical and experimental investigation of the Feeder “conical like" shape configuration. The experiments are focused on the aerodynamic force coefficients and the pressure distribution over the Feeder outer surface, while the numerical simulation cover also the analysis of the velocity and pressure distribution. Finally, the wind tunnel experiment is compared with its CFD model in order to validate such specific simulations with respective experiments and to better understand the difference between the wind tunnel and in-flight circumstances.