Abstract: In this paper, a new approach for target recognition based on the Empirical mode decomposition (EMD) algorithm of Huang etal. [11] and the energy tracking operator of Teager [13]-[14] is introduced. The conjunction of these two methods is called Teager-Huang analysis. This approach is well suited for nonstationary signals analysis. The impulse response (IR) of target is first band pass filtered into subsignals (components) called Intrinsic mode functions (IMFs) with well defined Instantaneous frequency (IF) and Instantaneous amplitude (IA). Each IMF is a zero-mean AM-FM component. In second step, the energy of each IMF is tracked using the Teager energy operator (TEO). IF and IA, useful to describe the time-varying characteristics of the signal, are estimated using the Energy separation algorithm (ESA) algorithm of Maragos et al .[16]-[17]. In third step, a set of features such as skewness and kurtosis are extracted from the IF, IA and IMF energy functions. The Teager-Huang analysis is tested on set of synthetic IRs of Sonar targets with different physical characteristics (density, velocity, shape,? ). PCA is first applied to features to discriminate between manufactured and natural targets. The manufactured patterns are classified into spheres and cylinders. One hundred percent of correct recognition is achieved with twenty three echoes where sixteen IRs, used for training, are free noise and seven IRs, used for testing phase, are corrupted with white Gaussian noise.
Abstract: In this paper, growth and collapse of a vapour bubble
generated due to a local energy input inside a rigid cylinder and in
the absence of buoyancy forces is investigated using Boundary
Integral Equation Method and Finite Difference Method .The fluid is
treated as potential flow and Boundary Integral Equation Method is
used to solve Laplace-s equation for velocity potential. Different
ratios of the diameter of the rigid cylinder to the maximum radius of
the bubble are considered. Results show that during the collapse
phase of the bubble inside a vertical rigid cylinder, two liquid micro
jets are developed on the top and bottom sides of the vapour bubble
and are directed inward. It is found that by increasing the ratio of the
cylinder diameter to the maximum radius of the bubble, the rate of
the growth and collapse phases of the bubble increases and the life
time of the bubble decreases.
Abstract: In a previously developed fast vortex method, the
diffusion of the vortex sheet induced at the solid wall by the no-slip
boundary conditions was modeled according to the approximation
solution of Koumoutsakos and converted into discrete blobs in the
vicinity of the wall. This scheme had been successfully applied to a
simulation of the flow induced with an impulsively initiated circular
cylinder. In this work, further modifications on this vortex method are
attempted, including replacing the approximation solution by the
boundary-element-method solution, incorporating a new algorithm for
handling the over-weak vortex blobs, and diffusing the vortex sheet
circulation in a new way suitable for high-curvature solid bodies. The
accuracy is thus largely improved. The predictions of lift and drag
coefficients for a uniform flow past a NASA airfoil agree well with the
existing literature.
Abstract: The present energy situation and the concerns
about global warming has stimulated active research interest
in non-petroleum, carbon free compounds and non-polluting
fuels, particularly for transportation, power generation, and
agricultural sectors. Environmental concerns and limited
amount of petroleum fuels have caused interests in the
development of alternative fuels for internal combustion (IC)
engines. The petroleum crude reserves however, are declining
and consumption of transport fuels particularly in the
developing countries is increasing at high rates. Severe
shortage of liquid fuels derived from petroleum may be faced
in the second half of this century. Recently more and more
stringent environmental regulations being enacted in the USA
and Europe have led to the research and development
activities on clean alternative fuels. Among the gaseous fuels
hydrogen is considered to be one of the clean alternative fuel.
Hydrogen is an interesting candidate for future internal
combustion engine based power trains. In this experimental
investigation, the performance and combustion analysis were
carried out on a direct injection (DI) diesel engine using
hydrogen with diesel following the TMI(Time Manifold
Injection) technique at different injection timings of 10
degree,45 degree and 80 degree ATDC using an electronic
control unit (ECU) and injection durations were controlled.
Further, the tests have been carried out at a constant speed of
1500rpm at different load conditions and it can be observed
that brake thermal efficiency increases with increase in load
conditions with a maximum gain of 15% at full load
conditions during all injection strategies of hydrogen. It was
also observed that with the increase in hydrogen energy share
BSEC started reducing and it reduced to a maximum of 9% as
compared to baseline diesel at 10deg ATDC injection during
maximum injection proving the exceptional combustion
properties of hydrogen.
Abstract: Simultaneous transient conduction and radiation heat
transfer with heat generation is investigated. Analysis is carried out
for both steady and unsteady situations. two-dimensional gray
cylindrical enclosure with an absorbing, emitting, and isotropically
scattering medium is considered. Enclosure boundaries are assumed
at specified temperatures. The heat generation rate is considered
uniform and constant throughout the medium. The lattice Boltzmann
method (LBM) was used to solve the energy equation of a transient
conduction-radiation heat transfer problem. The control volume finite
element method (CVFEM) was used to compute the radiative
information. To study the compatibility of the LBM for the energy
equation and the CVFEM for the radiative transfer equation, transient
conduction and radiation heat transfer problems in 2-D cylindrical
geometries were considered. In order to establish the suitability of the
LBM, the energy equation of the present problem was also solved
using the the finite difference method (FDM) of the computational
fluid dynamics. The CVFEM used in the radiative heat transfer was
employed to compute the radiative information required for the
solution of the energy equation using the LBM or the FDM (of the
CFD). To study the compatibility and suitability of the LBM for the
solution of energy equation and the CVFEM for the radiative
information, results were analyzed for the effects of various
parameters such as the boundary emissivity. The results of the LBMCVFEM
combination were found to be in excellent agreement with
the FDM-CVFEM combination. The number of iterations and the
steady state temperature in both of the combinations were found
comparable. Results are found for situations with and without heat
generation. Heat generation is found to have significant bearing on
temperature distribution.
Abstract: In this work the numerical simulation of transient heat
transfer in a cylindrical probe is done. An experiment was conducted
introducing a steel cylinder in a heating chamber and registering its
surface temperature along the time during one hour. In parallel, a
mathematical model was solved for one dimension transient heat
transfer in cylindrical coordinates, considering the boundary
conditions of the test. The model was solved using finite difference
method, because the thermal conductivity in the cylindrical steel bar
and the convection heat transfer coefficient used in the model are
considered temperature dependant functions, and both conditions
prevent the use of the analytical solution. The comparison between
theoretical and experimental results showed the average deviation is
below 2%. It was concluded that numerical methods are useful in
order to solve engineering complex problems. For constant k and h,
the experimental methodology used here can be used as a tool for
teaching heat transfer in mechanical engineering, using mathematical
simplified models with analytical solutions.
Abstract: This paper in essence presents comparative
experimental data on the mechanical performance of steel and
synthetic fibre-reinforced concrete under compression, tensile split
and flexure. URW1050 steel fibre and HPP45 synthetic fibre, both
with the same concrete design mix, have been used to make cube
specimens for a compression test, cylinders for a tensile split test and
beam specimens for a flexural test. The experimental data
demonstrated steel fibre reinforced concrete to be stronger in flexure
at early stages, whilst both fibre reinforced concrete types displayed
comparatively the same performance in compression, tensile splitting
and 28-day flexural strength. In terms of post-crack controlHPP45
was preferable.
Abstract: A zero dimensional model has been used to investigate
the combustion performance of a single cylinder direct injection
diesel engine fueled by biofuels with options like supercharging and
exhaust gas recirculation. The numerical simulation was performed at
constant speed. The indicated pressure, temperature diagrams are
plotted and compared for different fuels. The emissions of soot and
nitrous oxide are computed with phenomenological models. The
experimental work was also carried out with biodiesel (palm stearin
methyl ester) diesel blends, ethanol diesel blends to validate
simulation results with experimental results, and observed that the
present model is successful in predicting the engine performance with
biofuels.
Abstract: In this paper, mesh-free element free Galerkin (EFG) method is extended to solve two-dimensional potential flow problems. Two ideal fluid flow problems (i.e. flow over a rigid cylinder and flow over a sphere) have been formulated using variational approach. Penalty and Lagrange multiplier techniques have been utilized for the enforcement of essential boundary conditions. Four point Gauss quadrature have been used for the integration on two-dimensional domain (Ω) and nodal integration scheme has been used to enforce the essential boundary conditions on the edges (┌). The results obtained by EFG method are compared with those obtained by finite element method. The effects of scaling and penalty parameters on EFG results have also been discussed in detail.
Abstract: Helical milling operations are used to generate or
enlarge boreholes by means of a milling tool. The bore diameter can be
adjusted through the diameter of the helical path. The kinematics of
helical milling on a three axis machine tool is analysed firstly. The
relationships between processing parameters, cutting tool geometry
characters with machined hole feature are formulated. The feed motion
of the cutting tool has been decomposed to plane circular feed and
axial linear motion. In this paper, the time varying cutting forces acted
on the side cutting edges and end cutting edges of the flat end cylinder
miller is analysed using a discrete method separately. These two
components then are combined to produce the cutting force model
considering the complicated interaction between the cutters and
workpiece. The time varying cutting force model describes the
instantaneous cutting force during processing. This model could be
used to predict cutting force, calculate statics deflection of cutter and
workpiece, and also could be the foundation of dynamics model and
predicting chatter limitation of the helical milling operations.
Abstract: In the crack growth analysis, the Stress Intensity
Factor (SIF) is a fundamental prerequisite. In the present study, the
mode I stress intensity factor (SIF) of three-dimensional penny-
Shaped crack is obtained in an isotropic elastic cylindrical medium
with arbitrary dimensions under arbitrary loading at the top of the
cylinder, by the semi-analytical method based on the Rayleigh-Ritz
method. This method that is based on minimizing the potential
energy amount of the whole of the system, gives a very close results
to the previous studies. Defining the displacements (elastic fields) by
hypothetical functions in a defined coordinate system is the base of
this research. So for creating the singularity conditions at the tip of
the crack the appropriate terms should be found.
Abstract: A Finite Volume method based on Characteristic Fluxes for compressible fluids is developed. An explicit cell-centered resolution is adopted, where second and third order accuracy is provided by using two different MUSCL schemes with Minmod, Sweby or Superbee limiters for the hyperbolic part. Few different times integrator is used and be describe in this paper. Resolution is performed on a generic unstructured Cartesian grid, where solid boundaries are handled by a Cut-Cell method. Interfaces are explicitely advected in a non-diffusive way, ensuring local mass conservation. An improved cell cutting has been developed to handle boundaries of arbitrary geometrical complexity. Instead of using a polygon clipping algorithm, we use the Voxel traversal algorithm coupled with a local floodfill scanline to intersect 2D or 3D boundary surface meshes with the fixed Cartesian grid. Small cells stability problem near the boundaries is solved using a fully conservative merging method. Inflow and outflow conditions are also implemented in the model. The solver is validated on 2D academic test cases, such as the flow past a cylinder. The latter test cases are performed both in the frame of the body and in a fixed frame where the body is moving across the mesh. Adaptive Cartesian grid is provided by Paramesh without complex geometries for the moment.
Abstract: An experiment of vented gas explosions involving two
different cylinder vessel volumes (0.2 and 0.0065 m3) was reported,
with equivalence ratio (Φ) ranged from 0.3 to 1.6. Both vessels were
closed at the rear end and fitted at the other side with a circular
orifice plate that gives a constant vent coefficient (K =Av/V2/3) of
16.4. It was shown that end ignition gives higher overpressures than
central ignition, even though most of the published work on venting
uses central ignition. For propane and ethylene, it is found that rich
mixtures gave the highest overpressures and these mixtures are not
considered in current vent design guidance; which the guideline is
based on mixtures giving the maximum flame temperature. A strong
influence of the vessel volume at constant K was found for methane,
propane, ethylene and hydrogen-air explosions. It can be concluded
that self- acceleration of the flame, which is dependent on the
distance of a flame from the ignition and the ‘suction’ at the vent
opening are significant factors affecting the vent flow during
explosion development in vented gas explosion. This additional
volume influence on vented explosions is not taken into account in
the current vent design guidance.
Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: A prototype model of an emulsion separator was
designed and manufactured. Generally, it is a cylinder filled with
different fractal modules. The emulsion was fed into the reactor by a
peristaltic pump through an inlet placed at the boundary between the
two phases. For hydrodynamic design and sizing of the reactor the
assumptions of the theory of filtration were used and methods to
describe the separation process were developed. Based on this
methodology and using numerical methods and software of Autodesk
the process is simulated in different operating modes. The basic
hydrodynamic characteristics - speed and performance for different
types of fractal systems and decisions to optimize the design of the
reactor were also defined.
Abstract: A piston cylinder based high pressure differential
thermal analyzer system is developed to investigate phase
transformations, melting, glass transitions, crystallization behavior of
inorganic materials, glassy systems etc., at ambient to 4 GPa and at
room temperature to 1073 K. The pressure is calibrated by the phase
transition of bismuth and ytterbium and temperature is calibrated
by using thermocouple data chart. The system developed is
calibrated using benzoic acid, ammonium nitrate and it has a
pressure and temperature control of ± 8.9 x 10 -4 GPa , ± 2 K
respectively. The phase transition of Asx Te100-x chalcogenides,
ferrous oxide and strontium boride are studied using the
indigenously developed system.
Abstract: To compare Healing Effects of an
Ayurvedic Preparation and Silver Sulfadiazine on burn wounds in
Albino Rats.
Methods: Albino rats– 30 male / female rats weighing between
150-200 g were used in the study. They were individually housed and
maintained on normal diet and water ad libitum. Partial thickness
burn wounds were inflicted, on overnight-starved animals under
pentobarbitone (30mg/kg, i.p.) anaesthesia, by pouring hot molten
wax at 80oC into a plastic cylinder of 300 mm2 circular openings
placed on the shaven back of the animal. Apart from the drugs under
investigation no local/ systemic chemotherapeutic cover will be
provided to animals. All the animals were assessed for the percentage
of wound contraction, signs of infection, scab formation and
histopathological examination.
Results: Percentage of wound healing was significantly better in
the test ointment group compared to the standard. Signs of infection
were observed in more animals in the test ointment group compared
to the standard. Scab formation also took place earlier in the test
ointment group compared to standard. Epithelial regeneration and
healing profile was better in the test ointment compared to the
standard. Moreover the test ointment group did not show any raised
margins in the wound or blackish discoloration as was observed in
silver sulfadiazine group.
Conclusion: The burn wound healing effect of the ayurvedic
ointment under study is better in comparison to standard therapy of
silver sulfadiazine. The problem of infection encountered with the
test ointment can be overcome by changing the concentrations and
proportions of the ingredients in the test ointment which constitutes
the further plan of the study.
Abstract: Due to the stringent legislation for emission of diesel
engines and also increasing demand on fuel consumption, the
importance of detailed 3D simulation of fuel injection, mixing and
combustion have been increased in the recent years. In the present
work, FIRE code has been used to study the detailed modeling of
spray and mixture formation in a Caterpillar heavy-duty diesel
engine. The paper provides an overview of the submodels
implemented, which account for liquid spray atomization, droplet
secondary break-up, droplet collision, impingement, turbulent
dispersion and evaporation. The simulation was performed from
intake valve closing (IVC) to exhaust valve opening (EVO). The
predicted in-cylinder pressure is validated by comparing with
existing experimental data. A good agreement between the predicted
and experimental values ensures the accuracy of the numerical
predictions collected with the present work. Predictions of engine
emissions were also performed and a good quantitative agreement
between measured and predicted NOx and soot emission data were
obtained with the use of the present Zeldowich mechanism and
Hiroyasu model. In addition, the results reported in this paper
illustrate that the numerical simulation can be one of the most
powerful and beneficial tools for the internal combustion engine
design, optimization and performance analysis.
Abstract: Structural behavior of ring stiffened thick walled
cylinders made of functionally graded materials (FGMs) is
investigated in this paper. Functionally graded materials are inhomogeneous composites which are usually made from a mixture
of metal and ceramic. The gradient compositional variation of the
constituents from one surface to the other provides an elegant solution to the problem of high transverse shear stresses that are
induced when two dissimilar materials with large differences in material properties are bonded. FGM formation of the cylinder is
modeled by power-law exponent and the variation of characteristics is supposed to be in radial direction.
A finite element formulation is derived for the analysis. According to the property variation of the constituent materials in the radial
direction of the wall, it is not convenient to use conventional elements to model and analyze the structure of the stiffened FGM
cylinders. In this paper a new cylindrical super-element is used to model the finite element formulation and analyze the static and
modal behavior of stiffened FGM thick walled cylinders. By using
this super-element the number of elements, which are needed for
modeling, will reduce significantly and the process time is less in comparison with conventional finite element formulations. Results for static and modal analysis are evaluated and verified by
comparison to finite element formulation with conventional
elements. Comparison indicates a good conformity between results.
Abstract: There is a acute water problem especially in the dry
season in and around Perundurai (Erode district, Tamil Nadu, India)
where there are more number of tannery units. Hence an attempt was
made to use the waste water from tannery industry for construction
purpose. The mechanical properties such as compressive strength,
tensile strength, flexural strength etc were studied by casting various
concrete specimens in form of cube, cylinders and beams etc and
were found to be satisfactory. Hence some special properties such as
chloride attack, sulphate attack and chemical attack are considered
and comparatively studied with the conventional potable water. In
this experimental study the results of specimens prepared by using
treated and untreated tannery effluent were compared with the
concrete specimens prepared by using potable water. It was observed
that the concrete had some reduction in strength while subjected to
chloride attack, sulphate attack and chemical attack. So admixtures
were selected and optimized in suitable proportion to counter act the
adverse effects and the results were found to be satisfactory.