Abstract: This paper presents the use of phasor bond graphs to
obtain the steady-state behavior of a synchronous generator. The
phasor bond graph elements are built using 2D multibonds, which
represent the real and imaginary part of the phasor. The dynamic
bond graph model of a salient-pole synchronous generator is showed,
and verified viz. a sudden short-circuit test. The reduction of the
dynamic model into a phasor representation is described. The
previous test is executed on the phasor bond graph model, and its
steady-state values are compared with the dynamic response. Besides,
the widely used power (torque)-angle curves are obtained by means
of the phasor bond graph model, to test the usefulness of this model.
Abstract: This paper proposes a phasor representation of
electrical networks by using bond graph methodology. A so-called
phasor bond graph is built up by means of two-dimensional bonds,
which represent the complex plane. Impedances or admittances are
used instead of the standard bond graph elements. A procedure to
obtain the steady-state values from a phasor bond graph model is
presented. Besides the presentation of a phasor bond graph library in
SIDOPS code, also an application example is discussed.
Abstract: A bond graph model of a two degrees of freedom
PUMA is described. System inversion gives the system input
required to generate a given system output. In order to get the system
inversion of the PUMA manipulator, a linearization of the nonlinear
bond graph is obtained. Hence, the bicausality of the linearized bond
graph of the PUMA manipulator is applied. Thus, the bicausal bond
graph provides a systematic way of generating the equations of the
system inversion. Simulation results to verify the calculated input for
a given output are shown.
Abstract: The steady state response of bond graphs representing
passive and active suspension is presented. A bond graph with
preferred derivative causality assignment to get the steady state
is proposed. A general junction structure of this bond graph
is proposed. The proposed methodology to passive and active
suspensions is applied.
Abstract: In this paper, a bond graph dynamic model for a valvecontrolled
hydraulic cylinder has been developed. A simplified bond
graph model of the inter-actuator interactions in a multi-cylinder
hydraulic system has also been presented. The overall bond graph
model of a valve-controlled hydraulic cylinder was developed by
combining the bond graph sub-models of the pump, spool valve and
the actuator using junction structures. Causality was then assigned
in order to obtain a computational model which could be simulated.
The causal bond graph model of the hydraulic cylinder was verified
by comparing the open loop state responses to those of an ODE
model which had been developed in literature based on the same
assumptions. The results were found to correlate very well both
in the shape of the curves, magnitude and the response times,
thus indicating that the developed model represents the hydraulic
dynamics of a valve-controlled cylinder. A simplified model for interactuator
interaction was presented by connecting an effort source with
constant pump pressure to the zero-junction from which the cylinders
in a multi-cylinder system are supplied with a constant pressure from
the pump. On simulating the state responses of the developed model
under different situations of cylinder operations, indicated that such
a simple model can be used to predict the inter-actuator interactions.
Abstract: The main objective developed in this paper is to find a
graphic technique for modeling, simulation and diagnosis of the
industrial systems. This importance is much apparent when it is about
a complex system such as the nuclear reactor with pressurized water
of several form with various several non-linearity and time scales. In
this case the analytical approach is heavy and does not give a fast
idea on the evolution of the system. The tool Bond Graph enabled us
to transform the analytical model into graphic model and the
software of simulation SYMBOLS 2000 specific to the Bond Graphs
made it possible to validate and have the results given by the
technical specifications. We introduce the analysis of the problem
involved in the faults localization and identification in the complex
industrial processes. We propose a method of fault detection applied
to the diagnosis and to determine the gravity of a detected fault. We
show the possibilities of application of the new diagnosis approaches
to the complex system control. The industrial systems became
increasingly complex with the faults diagnosis procedures in the
physical systems prove to become very complex as soon as the
systems considered are not elementary any more. Indeed, in front of
this complexity, we chose to make recourse to Fault Detection and
Isolation method (FDI) by the analysis of the problem of its control
and to conceive a reliable system of diagnosis making it possible to
apprehend the complex dynamic systems spatially distributed applied
to the standard pressurized water nuclear reactor.
Abstract: This paper focuses on the development of bond graph
dynamic model of the mechanical dynamics of an excavating mechanism
previously designed to be used with small tractors, which are
fabricated in the Engineering Workshops of Jomo Kenyatta University
of Agriculture and Technology. To develop a mechanical dynamics
model of the manipulator, forward recursive equations similar to
those applied in iterative Newton-Euler method were used to obtain
kinematic relationships between the time rates of joint variables
and the generalized cartesian velocities for the centroids of the
links. Representing the obtained kinematic relationships in bondgraphic
form, while considering the link weights and momenta as
the elements led to a detailed bond graph model of the manipulator.
The bond graph method was found to reduce significantly the number
of recursive computations performed on a 3 DOF manipulator for a
mechanical dynamic model to result, hence indicating that bond graph
method is more computationally efficient than the Newton-Euler
method in developing dynamic models of 3 DOF planar manipulators.
The model was verified by comparing the joint torque expressions
of a two link planar manipulator to those obtained using Newton-
Euler and Lagrangian methods as analyzed in robotic textbooks. The
expressions were found to agree indicating that the model captures
the aspects of rigid body dynamics of the manipulator. Based on
the model developed, actuator sizing and valve sizing methodologies
were developed and used to obtain the optimal sizes of the pistons
and spool valve ports respectively. It was found that using the pump
with the sized flow rate capacity, the engine of the tractor is able to
power the excavating mechanism in digging a sandy-loom soil.
Abstract: A methodology to design a nonlinear observer in a
bond graph approach is proposed. The class of nonlinear observer
with multivariable nonlinearities is considered. A junction structure
of the bond graph observer is proposed. The proposed methodology
to an electrical transformer and a DC motor including the nonlinear
saturation is applied. Nonlinear observers for the transformer and DC
motor based on multivariable circle criterion in the physical domain
are proposed. In order to show the saturation effects on the
transformer and DC motor, simulation results are obtained. Finally,
the paper describes that convergence of the estimates to the true
states is achieved.
Abstract: This paper reviews various approaches that have been
used for the modeling and simulation of large-scale engineering
systems and determines their appropriateness in the development of a
RICS modeling and simulation tool. Bond graphs, linear graphs,
block diagrams, differential and difference equations, modeling
languages, cellular automata and agents are reviewed. This tool
should be based on linear graph representation and supports symbolic
programming, functional programming, the development of noncausal
models and the incorporation of decentralized approaches.