Abstract: In this investigation, a hypoeutectic AlSi11Cu alloy was printed. This alloy was obtained in powder form with an average particle size of 40 µm. Bars 20 mm in diameter and 100 mm in length were printed with the building direction parallel to the bars' longitudinal direction. The microstructural characterization demonstrated an Al matrix surrounded by a Si network forming a coral-like pattern. The microstructure of the alloy showed a heterogeneous behavior with a mixture of columnar and equiaxed grains. Likewise, the texture indicated that the columnar grains were preferentially oriented towards the building direction, while the equiaxed followed a texture dominated by the cube component. On the other hand, the as-printed material strength showed higher values than those obtained in the same alloy using conventional processes such as casting. In addition, strength and ductility differences were found in the printed material, depending on the measurement direction. The highest values were obtained in the radial direction (565 MPa maximum strength and 4.8% elongation to failure). The lowest values corresponded to the transverse direction (508 MPa maximum strength and 3.2 elongation to failure), which corroborate the material anisotropy.
Abstract: Earing defect in drawing process is highly undesirable not only because it adds on an additional trimming operation but also because the uneven material flow demands extra care. The objective of this work is to study the earing problem in the Deep Drawing of circular cup and to optimize the blank shape to reduce the earing. A finite element model is developed for 3-D numerical simulation of cup forming process in ABAQUS. Extra-deep-drawing (EDD) steel sheet has been used for simulation. Properties and tool design parameters were used as input for simulation. Earing was observed in the simulated cup and it was measured at various angles with respect to rolling direction. To reduce the earing defect initial blank shape was modified with the help of anisotropy coefficient. Modified blanks showed notable reduction in earing.
Abstract: In this work, the plastic behaviour of cold-rolled zinc
coated dual-phase steel sheets DP600 and DP800 grades is firstly
investigated with the help of uniaxial, hydraulic bulge and Forming
Limit Curve (FLC) tests. The uniaxial tensile tests were performed in
three angular orientations with respect to the rolling direction to
evaluate the strain-hardening and plastic anisotropy. True stressstrain
curves at large strains were determined from hydraulic bulge
testing and fitted to a work-hardening equation. The limit strains are
defined at both localized necking and fracture conditions according to
Nakajima’s hemispherical punch procedure. Also, an elasto-plastic
localization model is proposed in order to predict strain and stress
based forming limit curves. The investigated dual-phase sheets
showed a good formability in the biaxial stretching and drawing FLC
regions. For both DP600 and DP800 sheets, the corresponding
numerical predictions overestimated and underestimated the
experimental limit strains in the biaxial stretching and drawing FLC
regions, respectively. This can be attributed to the restricted failure
necking condition adopted in the numerical model, which is not
suitable to describe the tensile and shear fracture mechanisms in
advanced high strength steels under equibiaxial and biaxial stretching
conditions.
Abstract: This article is concerned with the determination of the static interaction of a vertically loaded rigid circular disc embedded at the interface of a horizontal layer sandwiched in between two different transversely isotropic half-spaces called as tri-material full-space. The axes of symmetry of different regions are assumed to be normal to the horizontal interfaces and parallel to the movement direction. With the use of a potential function method, and by implementing Hankel integral transforms in the radial direction, the government partial differential equation for the solely scalar potential function is transformed to an ordinary 4th order differential equation, and the mixed boundary conditions are transformed into a pair of integral equations called dual integral equations, which can be reduced to a Fredholm integral equation of the second kind, which is solved analytically. Then, the displacements and stresses are given in the form of improper line integrals, which is due to inverse Hankel integral transforms. It is shown that the present solutions are in exact agreement with the existing solutions for a homogeneous full-space with transversely isotropic material. To confirm the accuracy of the numerical evaluation of the integrals involved, the numerical results are compared with the solutions exists for the homogeneous full-space. Then, some different cases with different degrees of material anisotropy are compared to portray the effect of degree of anisotropy.
Abstract: Polarization-interferometric nonlinear confocal
microscopy is proposed for measuring a nano-sized particle with
optical anisotropy. The anisotropy in the particle was
spectroscopically imaged through a three-dimensional distribution of
third-order nonlinear dielectric polarization photoinduced.