Abstract: An adaptive Helmholtz resonator was designed and
adapted to hydraulics. The resonator was controlled by open- and
closed-loop controls so that 20 dB attenuation of the peak-to-peak
value of the pulsating pressure was maintained. The closed-loop
control was noted to be better, albeit it was slower because of its low
pressure and temperature variation, which caused variation in the
effective bulk modulus of the hydraulic system. Low-pressure
hydraulics contains air, which affects the stiffness of the hydraulics,
and temperature variation changes the viscosity of the oil. Thus, an
open-loop control loses its efficiency if a condition such as
temperature or the amount of air changes after calibration. The
instability of the low-pressure hydraulic system reduced the
operational frequency range of the Helmholtz resonator when
compared with the results of an analytical model.
Different dampers for hydraulics are presented. Then analytical
models of a hydraulic pipe and a hydraulic pipe with a Helmholtz
resonator are presented. The analytical models are based on the wave
equation of sound pressure. Finally, control methods and the results
of experiments are presented.
Abstract: Permanent magnet synchronous machines are known
as a good candidate for hybrid electric vehicles due to their unique
merits. However they have two major drawbacks i.e. high cost and
small speed range. In this paper an optimal design of a permanent
magnet machine is presented. A reduction of permanent magnet
material for a constant torque and an extension in speed and torque
ranges are chosen as the optimization aims. For this purpose the
analytical model of the permanent magnet synchronous machine is
derived and the appropriate design algorithm is devised. The genetic
algorithm is then employed to optimize some machine specifications.
Finally the finite element method is used to validate the designed
machine.
Abstract: In this paper we present modeling and simulation for
physical vapor deposition for metallic bipolar plates. In the models
we discuss the application of different models to simulate the
transport of chemical reactions of the gas species in the gas chamber.
The so called sputter process is an extremely sensitive process to
deposit thin layers to metallic plates. We have taken into account
lower order models to obtain first results with respect to the gas
fluxes and the kinetics in the chamber.
The model equations can be treated analytically in some
circumstances and complicated multi-dimensional models are solved
numerically with a software-package (UG unstructed grids, see [1]).
Because of multi-scaling and multi-physical behavior of the models,
we discuss adapted schemes to solve more accurate in the different
domains and scales. The results are discussed with physical
experiments to give a valid model for the assumed growth of thin
layers.
Abstract: In this paper, the telegraph equation is solved numerically by cubic B-spline quasi-interpolation .We obtain the numerical scheme, by using the derivative of the quasi-interpolation to approximate the spatial derivative of the dependent variable and a low order forward difference to approximate the temporal derivative of the dependent variable. The advantage of the resulting scheme is that the algorithm is very simple so it is very easy to implement. The results of numerical experiments are presented, and are compared with analytical solutions by calculating errors L2 and L∞ norms to confirm the good accuracy of the presented scheme.
Abstract: The velocity of a moving point in a general path is the vector quantity, which has both magnitude and direction. The magnitude or the direction of the velocity vector can change over time as a result of acceleration that the time rate of velocity changes. Acceleration analysis is important because inertial forces and inertial torques are proportional to rectilinear and angular accelerations accordingly. The loads must be determined in advance to ensure that a machine is adequately designed to handle these dynamic loads. For planar motion, the vector direction of acceleration is commonly separated into two elements: tangential and centripetal or radial components of a point on a rotating body. All textbooks in physics, kinematics and dynamics of machinery consider the magnitude of a radial acceleration at condition when a point rotates with a constant angular velocity and it means without acceleration. The magnitude of the tangential acceleration considered on a basis of acceleration for a rotating point. Such condition of presentation of magnitudes for two components of acceleration logically and mathematically is not correct and may cause further confusion in calculation. This paper presents new analytical expressions of the radial and absolute accelerations of a rotating point with acceleration and covers the gap in theoretical study of acceleration analysis.
Abstract: Efficient handoff algorithms are a cost-effective way
of enhancing the capacity and QoS of cellular system. The higher
value of hysteresis effectively prevents unnecessary handoffs but
causes undesired cell dragging. This undesired cell dragging causes
interference or could lead to dropped calls in microcellular
environment. The problems are further exacerbated by the corner
effect phenomenon which causes the signal level to drop by 20-30 dB
in 10-20 meters. Thus, in order to maintain reliable communication
in a microcellular system new and better handoff algorithms must be
developed. A fuzzy based handoff algorithm is proposed in this paper
as a solution to this problem. Handoff on the basis of ratio of slopes
of normal signal loss to the actual signal loss is presented. The fuzzy
based solution is supported by comparing its results with the results
obtained in analytical solution.
Abstract: This paper proposes an analytical method for the
dynamics of generating firms- alliance networks along with business
phases. Dynamics in network developments have previously been
discussed in the research areas of organizational strategy rather than in
the areas of regional cluster, where the static properties of the
networks are often discussed. The analytical method introduces the
concept of business phases into innovation processes and uses
relationships called prior experiences; this idea was developed in
organizational strategy to investigate the state of networks from the
viewpoints of tradeoffs between link stabilization and node
exploration. This paper also discusses the results of the analytical
method using five cases of the network developments of firms. The
idea of Embeddedness helps interpret the backgrounds of the
analytical results. The analytical method is useful for policymakers of
regional clusters to establish concrete evaluation targets and a
viewpoint for comparisons of policy programs.
Abstract: Bandwidth allocation in wired network is less complex
and to allocate bandwidth in wireless networks is complex and
challenging, due to the mobility of source end system.This paper
proposes a new approach to bandwidth allocation to higher and lower
priority mobile nodes.In our proposal bandwidth allocation to new
mobile node is based on bandwidth utilization of existing mobile
nodes.The first section of the paper focuses on introduction to
bandwidth allocation in wireless networks and presents the existing
solutions available for allocation of bandwidth. The second section
proposes the new solution for the bandwidth allocation to higher and
lower priority nodes. Finally this paper ends with the analytical
evaluation of the proposed solution.
Abstract: The aim of this paper is to develop a new two dimensional time accurate Euler solver for shock tube applications. The solver was developed to study the performance of a newly built short-duration hypersonic test facility at Universiti Tenaga Nasional “UNITEN" in Malaysia. The facility has been designed, built, and commissioned for different values of diaphragm pressure ratios in order to get wide range of Mach number. The developed solver uses second order accurate cell-vertex finite volume spatial discretization and forth order accurate Runge-Kutta temporal integration and it is designed to simulate the flow process for similar driver/driven gases (e.g. air-air as working fluids). The solver is validated against analytical solution and experimental measurements in the high speed flow test facility. Further investigations were made on the flow process inside the shock tube by using the solver. The shock wave motion, reflection and interaction were investigated and their influence on the performance of the shock tube was determined. The results provide very good estimates for both shock speed and shock pressure obtained after diaphragm rupture. Also detailed information on the gasdynamic processes over the full length of the facility is available. The agreements obtained have been reasonable.
Abstract: Falling has been one of the major concerns and threats
to the independence of the elderly in their daily lives. With the
worldwide significant growth of the aging population, it is essential
to have a promising solution of fall detection which is able to operate
at high accuracy in real-time and supports large scale implementation
using multiple cameras. Field Programmable Gate Array (FPGA) is a
highly promising tool to be used as a hardware accelerator in many
emerging embedded vision based system. Thus, it is the main
objective of this paper to present an FPGA-based solution of visual
based fall detection to meet stringent real-time requirements with
high accuracy. The hardware architecture of visual based fall
detection which utilizes the pixel locality to reduce memory accesses
is proposed. By exploiting the parallel and pipeline architecture of
FPGA, our hardware implementation of visual based fall detection
using FGPA is able to achieve a performance of 60fps for a series of
video analytical functions at VGA resolutions (640x480). The results
of this work show that FPGA has great potentials and impacts in
enabling large scale vision system in the future healthcare industry
due to its flexibility and scalability.
Abstract: Recently, bianisotropic media again received
increasing importance in electromagnetic theory because of advances
in material science which enable the manufacturing of complex
bianisotropic materials. By using Maxwell's equations and
corresponding boundary conditions, the electromagnetic field
distribution in bianisotropic solenoid coils is determined and the
influence of the bianisotropic behaviour of coil to the impedance and
Q-factor is considered. Bianisotropic media are the largest class of
linear media which is able to describe the macroscopic material
properties of artificial dielectrics, artificial magnetics, artificial chiral
materials, left-handed materials, metamaterials, and other composite
materials. Several special cases of coils, filled with complex
substance, have been analyzed. Results obtained by using the
analytical approach are compared with values calculated by
numerical methods, especially by our new hybrid EEM/BEM method
and FEM.
Abstract: Noise has adverse effect on human health and
comfort. Noise not only cause hearing impairment, but it also acts as
a causal factor for stress and raising systolic pressure. Additionally it
can be a causal factor in work accidents, both by marking hazards
and warning signals and by impeding concentration. Industry
workers also suffer psychological and physical stress as well as
hearing loss due to industrial noise. This paper proposes an approach
to enable engineers to point out quantitatively the noisiest source for
modification, while multiple machines are operating simultaneously.
The model with the point source and spherical radiation in a free field
was adopted to formulate the problem. The procedure works very
well in ideal cases (point source and free field). However, most of the
industrial noise problems are complicated by the fact that the noise is
confined in a room. Reflections from the walls, floor, ceiling, and
equipment in a room create a reverberant sound field that alters the
sound wave characteristics from those for the free field. So the model
was validated for relatively low absorption room at NIT Kurukshetra
Central Workshop. The results of validation pointed out that the
estimated sound power of noise sources under simultaneous
conditions were on lower side, within the error limits 3.56 - 6.35 %.
Thus suggesting the use of this methodology for practical
implementation in industry. To demonstrate the application of the
above analytical procedure for estimating the sound power of noise
sources under simultaneous operating conditions, a manufacturing
facility (Railway Workshop at Yamunanagar, India) having five
sound sources (machines) on its workshop floor is considered in this
study. The findings of the case study had identified the two most
effective candidates (noise sources) for noise control in the Railway
Workshop Yamunanagar, India. The study suggests that the
modification in the design and/or replacement of these two identified
noisiest sources (machine) would be necessary so as to achieve an
effective reduction in noise levels. Further, the estimated data allows
engineers to better understand the noise situations of the workplace
and to revise the map when changes occur in noise level due to a
workplace re-layout.
Abstract: Wavelet transform has been extensively used in
machine fault diagnosis and prognosis owing to its strength to deal
with non-stationary signals. The existing Wavelet transform based
schemes for fault diagnosis employ wavelet decomposition of the
entire vibration frequency which not only involve huge
computational overhead in extracting the features but also increases
the dimensionality of the feature vector. This increase in the
dimensionality has the tendency to 'over-fit' the training data and
could mislead the fault diagnostic model. In this paper a novel
technique, envelope wavelet packet transform (EWPT) is proposed in
which features are extracted based on wavelet packet transform of the
filtered envelope signal rather than the overall vibration signal. It not
only reduces the computational overhead in terms of reduced number
of wavelet decomposition levels and features but also improves the
fault detection accuracy. Analytical expressions are provided for the
optimal frequency resolution and decomposition level selection in
EWPT. Experimental results with both actual and simulated machine
fault data demonstrate significant gain in fault detection ability by
EWPT at reduced complexity compared to existing techniques.
Abstract: The possibilities of mobile technology generate new
demands for vocational teacher trainers to transform their approach
to work and to incorporate its usage into their ordinary educational
practice. This paper presents findings of a focus discussion group
(FDG) session on the usage of iPads within a school of vocational
teacher education (SoVTE). It aims to clarify how the teacher
trainers are using iPads and what has changed in their work during
the usage of iPads. The analytical framework bases on content
analysis and expansive learning cycle. It was not only found what
kind of a role iPads played in their daily practices but it brought also
into attention how a cultural change regarding the usage of social
media and mobile technology was desperately needed in the whole
work community. Thus, the FGD was abducted for developing the
knowledge practices of the community of the SoVTE.
Abstract: Timing driven physical design, synthesis, and
optimization tools need efficient closed-form delay models for
estimating the delay associated with each net in an integrated circuit
(IC) design. The total number of nets in a modern IC design has
increased dramatically and exceeded millions. Therefore efficient
modeling of interconnection is needed for high speed IC-s. This
paper presents closed–form expressions for RC and RLC
interconnection trees in current mode signaling, which can be
implemented in VLSI design tool. These analytical model
expressions can be used for accurate calculation of delay after the
design clock tree has been laid out and the design is fully routed.
Evaluation of these analytical models is several orders of magnitude
faster than simulation using SPICE.
Abstract: Bicycle configuration is not as large as those of motorcycles or automobiles, while it indeed composes a complicated dynamic system. People-s requirements on comfortability, controllability and safety grow higher as the research and development technologies improve. The shock absorber affects the vehicle suspension performances enormously. The absorber takes the vibration energy and releases it at a suitable time, keeping the wheel under a proper contact condition with road surface, maintaining the vehicle chassis stability. Suspension design for mountain bicycles is more difficult than that of city bikes since it encounters dynamic variations on road and loading conditions. Riders need a stiff damper as they exert to tread on the pedals when climbing, while a soft damper when they descend downhill. Various switchable shock absorbers are proposed in markets, however riders have to manually switch them among soft, hard and lock positions. This study proposes a novel design of the bicycle shock absorber, which provides automatic smooth tuning of the damping coefficient, from a predetermined lower bound to theoretically unlimited. An automatic quick releasing valve is involved in this design so that it can release the peak pressure when the suspension fork runs into a square-wave type obstacle and prevent the chassis from damage, avoiding the rider skeleton from injury. This design achieves the automatic tuning process by innovative plunger valve and fluidic passage arrangements without any electronic devices. Theoretical modelling of the damper and spring are established in this study. Design parameters of the valves and fluidic passages are determined. Relations between design parameters and shock absorber performances are discussed in this paper. The analytical results give directions to the shock absorber manufacture.
Abstract: Analysis of reciprocating equipment piston rod leads
to nonlinear elastic-plastic deformation analysis of rod with initial
imperfection under axial dynamic load. In this paper a new and
effective model and analytical formulations are presented to evaluate
dynamic deformation and elastic-plastic stresses of reciprocating
machine piston rod. This new method has capability to account for
geometric nonlinearity, elastic-plastic deformation and dynamic
effects. Proposed method can be used for evaluation of piston rod
performance for various reciprocating machines under different
operation situations. Rod load curves and maximum allowable rod
load are calculated with presented method for a refinery type
reciprocating compressor. Useful recommendations and guidelines
for rod load, rod load reversal and rod drop monitoring are also
addressed.
Abstract: An unstructured finite volume numerical model is
presented here for simulating shallow-water flows with wetting and
drying fronts. The model is based on the Green-s theorem in
combination with Chorin-s projection method. A 2nd-order upwind
scheme coupled with a Least Square technique is used to handle
convection terms. An Wetting and drying treatment is used in the
present model to ensures the total mass conservation. To test it-s
capacity and reliability, the present model is used to solve the
Parabolic Bowl problem. We compare our numerical solutions with
the corresponding analytical and existing standard numerical results.
Excellent agreements are found in all the cases.
Abstract: The main goal of the present work is to decrease the
computational burden for optimum design of steel frames with
frequency constraints using a new type of neural networks called
Wavelet Neural Network. It is contested to train a suitable neural
network for frequency approximation work as the analysis program.
The combination of wavelet theory and Neural Networks (NN)
has lead to the development of wavelet neural networks.
Wavelet neural networks are feed-forward networks using
wavelet as activation function. Wavelets are mathematical
functions within suitable inner parameters, which help them to
approximate arbitrary functions. WNN was used to predict the
frequency of the structures. In WNN a RAtional function with
Second order Poles (RASP) wavelet was used as a transfer
function. It is shown that the convergence speed was faster
than other neural networks. Also comparisons of WNN with
the embedded Artificial Neural Network (ANN) and with
approximate techniques and also with analytical solutions are
available in the literature.
Abstract: Proper management of residues originated from
industrial activities is considered as one of the serious challenges
faced by industrial societies due to their potential hazards to the
environment. Common disposal methods for industrial solid wastes
(ISWs) encompass various combinations of solely management
options, i.e. recycling, incineration, composting, and sanitary
landfilling. Indeed, the procedure used to evaluate and nominate the
best practical methods should be based on environmental, technical,
economical, and social assessments. In this paper an environmentaltechnical
assessment model is developed using analytical network
process (ANP) to facilitate the decision making practice for ISWs
generated at Gilan province, Iran. Using the results of performed
surveys on industrial units located at Gilan, the various groups of
solid wastes in the research area were characterized, and four
different ISW management scenarios were studied. The evaluation
process was conducted using the above-mentioned model in the
Super Decisions software (version 2.0.8) environment. The results
indicates that the best ISW management scenario for Gilan province
is consist of recycling the metal industries residues, composting the
putrescible portion of ISWs, combustion of paper, wood, fabric and
polymeric wastes as well as energy extraction in the incineration
plant, and finally landfilling the rest of the waste stream in addition
with rejected materials from recycling and compost production plants
and ashes from the incineration unit.