Abstract: In the present paper, a numerical investigation has
been carried out to classify and clarify the effects of paramount
parameters on turbulent impinging slot jets. The effects of nozzle-s
exit turbulent intensity, distance between nozzle and impinging plate
are studied at Reynolds number 5000 and 20000. In addition, the
effect of Mach number that is varied between 0.3-0.8 at a constant
Reynolds number 133000 is investigated to elucidate the effect of
compressibility in impinging jet upon a flat plate. The wall that is
located at the same level with nozzle-s exit confines the flow. A
compressible finite volume solver is implemented for simulation the
flow behavior. One equation Spalart-Allmaras turbulent model is
used to simulate turbulent flow at this study. Assessment of the
Spalart-Allmaras turbulent model at high nozzle to plate distance,
and giving enough insights to characterize the effect of Mach number
at high Reynolds number for the complex impinging jet flow are the
remarkable results of this study.
Abstract: In this study, the numerical solution of unsteady flow
between two concentric rotating spheres with suction and blowing at
their boundaries is presented. The spheres are rotating about a
common axis of rotation while their angular velocities are constant.
The Navier-Stokes equations are solved by employing the finite
difference method and implicit scheme. The resulting flow patterns
are presented for various values of the flow parameters including
rotational Reynolds number Re , and a blowing/suction Reynolds
number Rew . Viscous torques at the inner and the outer spheres are
calculated, too. It is seen that increasing the amount of suction and
blowing decrease the size of eddies generated in the annulus.
Abstract: In this work, we experimentally study heat transfer
from exhaust particulate air of detergent spray drying tower to water
by using coiled tube heat exchanger. Water flows in the coiled
tubes, where air loaded with detergent particles of 43 micrometers
in diameter flows within the shell. Four coiled tubes with different
coil pitches are used in a counter-current flow configuration. We
investigate heat transfer coefficients of inside and outside the heat
transfer surfaces through 400 experiments. The correlations between
Nusselt number and Reynolds number, Prandtl number, mass flow
rate of particulates to mass flow rate of air ratio and coiled tube
pitch parameter are proposed. The correlations procured can be used
to predicted heat transfer between tube and shell of the heat
exchanger.
Abstract: This paper presents results obtained from the
numerical solution for the flow past an oscillating circular cylinder at
Reynolds number of 200. The frequency of oscillation was fixed to
the vortex shedding frequency from a fixed cylinder, f0, while the
amplitudes of oscillations were varied from to 1.1a, where a
represents the radius of the cylinder. The response of the flow
through the fluid forces acting on the surface of the cylinder are
investigated. The lock-on phenomenon is captured at low oscillation
amplitudes.
Abstract: The purpose of the present study is to analyze the
effect of the target plate-s curvature on the heat transfer in laminar
confined impinging jet flows. Numerical results from two
dimensional compressible finite volume solver are compared
between three different shapes of impinging plates: Flat, Concave
and Convex plates. The remarkable result of this study proves that
the stagnation Nusselt number in laminar range of Reynolds number
based on the slot width is maximum in convex surface and is
minimum in concave plate. These results refuse the previous data in
literature stating the amount of the stagnation Nusselt number is
greater in concave surface related to flat plate configuration.
Abstract: Circle grid space filling plate is a flow conditioner with a fractal pattern and used to eliminate turbulence originating from pipe fittings in experimental fluid flow applications. In this paper, steady state, incompressible, swirling turbulent flow through circle grid space filling plate has been studied. The solution and the analysis were carried out using finite volume CFD solver FLUENT 6.2. Three turbulence models were used in the numerical investigation and their results were compared with the pressure drop correlation of BS EN ISO 5167-2:2003. The turbulence models investigated here are the standard k-ε, realizable k-ε, and the Reynolds Stress Model (RSM). The results showed that the RSM model gave the best agreement with the ISO pressure drop correlation. The effects of circle grids space filling plate thickness and Reynolds number on the flow characteristics have been investigated as well.
Abstract: Study fluid flow and heat transfer characteristics of
microchannel in a primary Cross-corrugated(CC) surface recuperators
with corrugations and without corrugations, using CFD method. The
pitch-over-height ratios P/H of Cross-corrugated (CC) surface is from
1.5 to 4.0, included angles β=75º. The study was performed using CFD
software FLUENT to create unit model and simulate fluid
temperature, velocity, heat transfer coefficient and other parameters.
The results from these simulations were compared to experimental
data. It is concluded that, when the Reynolds number is constant, if
increase P/H, j/f will decrease, also the decreasing trend will become
weak. Under the condition of P/H=2.2, if increase the inlet velocity j/f
will decrease; in addition, the heat transfer performance in surface
with corrugation will increase 10% compared to that without
corrugation. The study results can provide the basis to optimize the
design, select the type of heat transfer surface, the scale structure, and
heat-transfer surface arrangement for recuperators.
Abstract: The study concerns an experimental investigation in
the laboratory of the water erosion using a rainfall simulator. We
have focused our attention on the influence of rainfall intensity on
some hydraulic characteristics. The results obtained allow us to
conclude that there is a significant correlation between rainfall
intensity and hydraulic characteristics of runoff (Reynolds number,
Froude number) and sediment concentration.
Abstract: In this work, stationary hot-wire measurements are
carried out to investigate the characteristics of a round free jet in its
potential core region (0 ≤ x/d ≤ 10). Measurements are carried out on
an incompressible round jet for a range of Reynolds numbers from
4000 to 8000, calculated based on the jet exit mean velocity and the
nozzle diameter. The effect of flow velocity on the development
characteristics of the jet in the core region is analyzed. Timeaveraged
statistics, spectra of velocity and its higher order moments
are presented and explained.
Abstract: This paper describes an experimental, theoretical
model and numerical study of concentrated vortex flow past a sphere
in a hydraulic check valve. The phenomenon of the rotation of the
ball around the axis of the device through which liquid flows has
been found. That is, due to the rotation of the sphere in the check
valve vibration is caused. We observe the rotation of the sphere
around the longitudinal axis of the check valve. This rotation is
induced by a vortex shedding from the sphere. We will discuss
computational simulation and experimental investigations of this
strong sphere rotation. The frequency of the sphere vibration and
interaction with the check valve wall has been measured as a function
of the wide range Reynolds Number. The validity of the
computational simulation and of the assumptions on which it is based
has been proved experimentally. This study demonstrates the
possibility to control the vibrations in a hydraulic system and proves
to be very effective suppression of the self-excited vibration.
Abstract: To achieve reliable solutions, today-s numerical and
experimental activities need developing more accurate methods and
utilizing expensive facilities, respectfully in microchannels. The analytical
study can be considered as an alternative approach to alleviate
the preceding difficulties. Among the analytical solutions, those with
high robustness and low complexities are certainly more attractive.
The perturbation theory has been used by many researchers to analyze
microflows. In present work, a compressible microflow with constant
heat flux boundary condition is analyzed. The flow is assumed to be
fully developed and steady. The Mach and Reynolds numbers are also
assumed to be very small. For this case, the creeping phenomenon
may have some effect on the velocity profile. To achieve robustness
solution it is assumed that the flow is quasi-isothermal. In this study,
the creeping term which appears in the slip boundary condition
is formulated by different mathematical formulas. The difference
between this work and the previous ones is that the creeping term
is taken into account and presented in non-dimensionalized form.
The results obtained from perturbation theory are presented based
on four non-dimensionalized parameters including the Reynolds,
Mach, Prandtl and Brinkman numbers. The axial velocity, normal
velocity and pressure profiles are obtained. Solutions for velocities
and pressure for two cases with different Br numbers are compared
with each other and the results show that the effect of creeping
phenomenon on the velocity profile becomes more important when
Br number is less than O(ε).
Abstract: The present work describes a computational study of
aerodynamic characteristics of GLC305 airfoil clean and with 16.7
min ice shape (rime 212) and 22.5 min ice shape (glaze 944).The
performance of turbulence models SA, Kε, Kω Std, and Kω SST
model are observed against experimental flow fields at different
Mach numbers 0.12, 0.21, 0.28 in a range of Reynolds numbers
3x106, 6x106, and 10.5x106 on clean and iced aircraft airfoil
GLC305. Numerical predictions include lift, drag and pitching
moment coefficients at different Mach numbers and at different angle
of attacks were done. Accuracy of solutions with respect to the
effects of turbulence models, variation of Mach number, initial
conditions, grid resolution and grid spacing near the wall made the
study much sensitive. Navier Stokes equation based computational
technique is used. Results are very close to the experimental results.
It has seen that SA and SST models are more efficient than Kε and
Kω standard in under study problem.
Abstract: Radial flow reactor was focused for large scale
methanol synthesis and in which the heat transfer type was cross-flow.
The effects of operating conditions including the reactor inlet air
temperature, the heating pipe temperature and the air flow rate on the
cross-flow heat transfer was investigated and the results showed that
the temperature profile of the area in front of the heating pipe was
slightly affected by all the operating conditions. The main area whose
temperature profile was influenced was the area behind the heating
pipe. The heat transfer direction according to the air flow directions. In
order to provide the basis for radial flow reactor design calculation, the
dimensionless number group method was used for data fitting of the
bed effective thermal conductivity and the wall heat transfer
coefficient which was calculated by the mathematical model with the
product of Reynolds number and Prandtl number. The comparison of
experimental data and calculated value showed that the calculated
value fit the experimental data very well and the formulas could be
used for reactor designing calculation.
Abstract: The purpose of this study was to explore the complex
flow structure a novel active-type micromixer that based on concept of
Wankle-type rotor. The characteristics of this micromixer are two
folds; a rapid mixing of reagents in a limited space due to the
generation of multiple vortices and a graduate increment in dynamic
pressure as the mixed reagents is delivered to the output ports.
Present micro-mixer is consisted of a rotor with shape of triangle
column, a blending chamber and several inlet and outlet ports. The
geometry of blending chamber is designed to make the rotor can be
freely internal rotated with a constant eccentricity ratio. When the
shape of the blending chamber and the rotor are fixed, the effects of
rotating speed of rotor and the relative locations of ports on the mixing
efficiency are numerical studied. The governing equations are
unsteady, two-dimensional incompressible Navier-Stokes equation
and the working fluid is the water. The species concentration equation
is also solved to reveal the mass transfer process of reagents in various
regions then to evaluate the mixing efficiency.
The dynamic mesh technique was implemented to model the
dynamic volume shrinkage and expansion of three individual
sub-regions of blending chamber when the rotor conducted a complete
rotating cycle. Six types of ports configuration on the mixing
efficiency are considered in a range of Reynolds number from 10 to
300. The rapid mixing process was accomplished with the multiple
vortex structures within a tiny space due to the equilibrium of shear
force, viscous force and inertial force. Results showed that the highest
mixing efficiency could be attained in the following conditions: two
inlet and two outlet ports configuration, that is an included angle of 60
degrees between two inlets and an included angle of 120 degrees
between inlet and outlet ports when Re=10.
Abstract: In this paper, fluid flow patterns of steady incompressible flow inside shear driven cavity are studied. The numerical simulations are conducted by using lattice Boltzmann method (LBM) for different Reynolds numbers. In order to simulate the flow, derivation of macroscopic hydrodynamics equations from the continuous Boltzmann equation need to be performed. Then, the numerical results of shear-driven flow inside square and triangular cavity are compared with results found in literature review. Present study found that flow patterns are affected by the geometry of the cavity and the Reynolds numbers used.
Abstract: Periodic vortex shedding in pulsating flow inside wavy
channel and the effect it has on heat transfer are studied using the
finite volume method. A sinusoidally-varying component is superimposed
on a uniform flow inside a sinusoidal wavy channel and
the effects on the Nusselt number is analyzed. It was found that a
unique optimum value of the pulsation frequency, represented by the
Strouhal number, exists for Reynolds numbers ranging from 125 to
1000. Results suggest that the gain in heat transfer is related to the
process of vortex formation, movement about the troughs of the wavy
channel, and subsequent ejection/destruction through the converging
section. Heat transfer is the highest when the frequencies of the
pulsation and vortex formation approach being in-phase. Analysis of
Strouhal number effect on Nu over a period of pulsation substantiates
the proposed physical mechanism for enhancement. The effect of
changing the amplitude of pulsation is also presented over a period
of pulsation, showing a monotonic increase in heat transfer with
increasing amplitude. The 60% increase in Nusselt number suggests
that sinusoidal fluid pulsation can an effective method for enhancing
heat transfer in laminar, wavy-channel flows.
Abstract: Stuck-pipe in drilling operations is one of the most
pressing and expensive problems in the oil industry. This paper
describes a computational simulation and an experimental study of
the hydrodynamic vibrator, which may be used for liquidation of
stuck-pipe problems during well drilling. The work principle of the
vibrator is based upon the known phenomena of Vortex Street of
Karman and the resulting generation of vibrations. We will discuss
the computational simulation and experimental investigations of
vibrations in this device. The frequency of the vibration parameters
has been measured as a function of the wide range Reynolds Number.
The validity of the computational simulation and of the assumptions
on which it is based has been proved experimentally. The
computational simulation of the vibrator work and its effectiveness
was carried out using FLUENT software. The research showed high
degree of congruence with the results of the laboratory tests and
allowed to determine the effect of the granular material features upon
the pipe vibration in the well. This study demonstrates the potential
of using the hydrodynamic vibrator in a well drilling system.