Abstract: Flexible satellites are equipped with various appendages which vibrate under the influence of any excitation and make the attitude of the satellite to be unstable. Therefore, the system must be able to adjust to balance the effect of these appendages in order to point accurately and satisfactorily which is one of the most important problems in satellite design. Proportional Integral Derivative (PID) Controller is simple to design and computationally efficient to implement which is used to stabilize the effect of these flexible appendages. However, manual turning of the PID is time consuming, waste energy and money. Particle Swarm Optimization (PSO) is used to tune the parameters of PID Controller. Simulation results obtained show that PSO tuned PID Controller is able to re-orient the spacecraft attitude as well as dampen the effect of mechanical resonance and yields better performance when compared with manually tuned PID Controller.
Abstract: In this paper, a PSO based fractional order PID (FOPID) controller is proposed for concentration control of an isothermal Continuous Stirred Tank Reactor (CSTR) problem. CSTR is used to carry out chemical reactions in industries, which possesses complex nonlinear dynamic characteristics. Particle Swarm Optimization algorithm technique, which is an evolutionary optimization technique based on the movement and intelligence of swarm is proposed for tuning of the controller for this system. Comparisons of proposed controller with conventional and fuzzy based controller illustrate the superiority of proposed PSO-FOPID controller.
Abstract: Control of diesel engine’s air path has drawn a lot of attention due to its multi input-multi output, closed coupled, non-linear relation. Today, precise control of amount of air to be combusted is a must in order to meet with tight emission limits and performance targets. In this study, passenger car size diesel engine is modeled by AVL Boost RT, and then simulated with standard, industry level PID controllers. Finally, linear model predictive control is designed and simulated. This study shows the importance of modeling and control of diesel engines with flexible algorithm development in computer based systems.
Abstract: In this paper, the unstable angle of attack of a
FOXTROT aircraft is controlled by using Genetic Algorithm based
flight controller and the result is compared with the conventional
techniques like Tyreus-Luyben (TL), Ziegler-Nichols (ZN) and
Interpolation Rule (IR) for tuning the PID controller. In addition, the
performance indices like Mean Square Error (MSE), Integral Square
Error (ISE), and Integral Absolute Time Error (IATE) etc. are
improved by using Genetic Algorithm. It was established that the
error by using GA is very less as compared to the conventional
techniques thereby improving the performance indices of the
dynamic system.
Abstract: This paper presents a comparative analysis of
continuously stirred tank reactor (CSTR) control based on adaptive
control and optimal tuning of PID control based on particle swarm
optimization. In the design of adaptive control, Model reference
adaptive control (MRAC) scheme is used, in which the adaptation
law have been developed by MIT rule & Lyapunov’s rule. In PSO
control parameters of PID controller is tuned by using the concept of
particle swarm optimization to get optimized operating point for
minimum integral square error (ISE) condition. The results show the
adjustment of PID parameters converting into the optimal operating
point and the good control response can be obtained by the PSO
technique.
Abstract: This paper presents the advantages of fuzzy control use in technological processes control. The paper presents a real application of the Linguistic Fuzzy-Logic Control, developed at the University of Ostrava for the control of physical models in the Intelligent Systems Laboratory. The paper presents an example of a sensitive non-linear model, such as a magnetic levitation model and obtained results which show how modern information technologies can help to solve actual technical problems. A special method based on the LFLC controller with partial components is presented in this paper followed by the method of automatic context change, which is very helpful to achieve more accurate control results. The main advantage of the used system is its robustness in changing conditions demonstrated by comparing with conventional PID controller. This technology and real models are also used as a background for problem-oriented teaching, realized at the department for master students and their collaborative as well as individual final projects.
Abstract: Optimizing the parameters in the controller plays a
vital role in the control theory and its applications. Optimizing the
PID parameters is finding out the best value from the feasible
solutions. Finding the optimal value is an optimization problem.
Inverted Pendulum is a very good platform for control engineers to
verify and apply different logics in the field of control theory. It is
necessary to find an optimization technique for the controller to tune
the values automatically in order to minimize the error within the
given bounds. In this paper, the algorithmic concepts of Harmony
search (HS) and Genetic Algorithm (GA) have been analyzed for the
given range of values. The experimental results show that HS
performs well than GA.
Abstract: In this paper, an autonomous hovering control method
of multicopter using only Web camera is proposed. Recently, various
control method of an autonomous flight for multicopter are proposed.
But, in the previous proposed methods, a motion capture system
(i. e., OptiTrack) and laser range finder are often used to measure
the position and posture of multicopter. To achieve an autonomous
flight control of multicopter with simple equipments, we propose
an autonomous flight control method using AR marker and Web
camera. AR marker can measure the position of multicopter with
Cartesian coordinate in three dimensional, then its position connects
with aileron, elevator, and accelerator throttle operation. A simple
PID control method is applied to the each operation and adjust
the controller gains. Experimental results are given to show the
effectiveness of our proposed method. Moreover, another simple
operation method for autonomous flight control multicopter is also
proposed.
Abstract: At present, the cascade PID control is widely used to
control the superheating temperature (main steam temperature). As
Main Steam Temperature has the characteristics of large inertia, large
time-delay and time varying, etc., conventional PID control strategy
cannot achieve good control performance. In order to overcome the
bad performance and deficiencies of main steam temperature control
system, Model Free Adaptive Control (MFAC) - P cascade control
system is proposed in this paper. By substituting MFAC in PID of the
main control loop of the main steam temperature control, it can
overcome time delays, non-linearity, disturbance and time variation.
Abstract: This paper provides a comparative study on the
performances of standard PID and adaptive PID controllers tested on
travel angle of a 3-Degree-of-Freedom (3-DOF) Quanser bench-top
helicopter. Quanser, a well-known manufacturer of educational
bench-top helicopter has developed Proportional Integration
Derivative (PID) controller with Linear Quadratic Regulator (LQR)
for all travel, pitch and yaw angle of the bench-top helicopter. The
performance of the PID controller is relatively good; however, its
performance could also be improved if the controller is combined
with adaptive element. The objective of this research is to design
adaptive PID controller and then compare the performances of the
adaptive PID with the standard PID. The controller design and test is
focused on travel angle control only. Adaptive method used in this
project is self-tuning controller, which controller’s parameters are
updated online. Two adaptive algorithms those are pole-placement
and deadbeat have been chosen as the method to achieve optimal
controller’s parameters. Performance comparisons have shown that
the adaptive (deadbeat) PID controller has produced more desirable
performance compared to standard PID and adaptive (poleplacement).
The adaptive (deadbeat) PID controller attained very fast
settling time (5 seconds) and very small percentage of overshoot (5%
to 7.5%) for 10° to 30° step change of travel angle.
Abstract: This paper explains about the voltage output for DC to
DC boost converter between open loop, PID controller and fuzzy
logic controller through Matlab Simulink. Simulink input voltage was
set at 12V and the voltage reference was set at 24V. The analysis on
the deviation of voltage resulted that the difference between reference
voltage setting and the output voltage is always lower. Comparison
between open loop, PID and FLC shows that, the open loop circuit
having a bit higher on the deviation of voltage. The PID circuit
boosts for FLC has a lesser deviation of voltage and proved that it is
such a better performance on control the deviation of voltage during
the boost mode.
Abstract: Control of a semi-batch polymerization reactor using
an adaptive radial basis function (RBF) neural network method is
investigated in this paper. A neural network inverse model is used to
estimate the valve position of the reactor; this method can identify the
controlled system with the RBF neural network identifier. The
weights of the adaptive PID controller are timely adjusted based on
the identification of the plant and self-learning capability of RBFNN.
A PID controller is used in the feedback control to regulate the actual
temperature by compensating the neural network inverse model
output. Simulation results show that the proposed control has strong
adaptability, robustness and satisfactory control performance and the
nonlinear system is achieved.
Abstract: In this paper, fractional order feedback control of a ball
beam model is investigated. The ball beam model is a particular
example of the double Integrator system having strongly nonlinear
characteristics and unstable dynamics which make the control of
such system a challenging task. Most of the work in fractional order
control systems are in theoretical nature and controller design and its
implementation in practice is very small. In this work, a successful
attempt has been made to design a fractional order PIλDμcontroller
for a benchmark laboratory ball and beam model. Better performance
can be achieved using a fractional order PID controller and it is
demonstrated through simulations results with a comparison to the
classic PID controller.
Abstract: In this paper we deal with using Lego Mindstorms in
simulation of robotic systems with respect to cost reduction. Lego
Mindstorms kit contains broad variety of hardware components
which are required to simulate, program and test the robotics systems
in practice. Algorithm programming went in development
environment supplied together with Lego kit as in programming
language C# as well. Algorithm following the line, which we dealt
with in this paper, uses theoretical findings from area of controlling
circuits. PID controller has been chosen as controlling circuit whose
individual components were experimentally adjusted for optimal
motion of robot tracking the line. Data which are determined to
process by algorithm are collected by sensors which scan the
interface between black and white surfaces followed by robot. Based
on discovered facts Lego Mindstorms can be considered for low-cost
and capable kit to simulate real robotics systems.
Abstract: In this paper, a 2DOF (two degrees of freedom) PID (Proportional-Integral-Derivative) controller based on MPC (Model predictive control) algorithm fo slip suppression of EV (Electric Vehicle) under braking is proposed. The proposed method aims to improve the safety and the stability of EVs under braking by controlling the wheel slip ration. There also include numerical simulation results to demonstrate the effectiveness of the method.
Abstract: In industrial environments, the heat exchanger is a
necessary component to any strategy of energy conversion. Much of
thermal energy used in industrial processes passes at least one times
by a heat exchanger, and methods systems recovering thermal
energy.
This survey paper tries to presents in a systemic way an sample
control of a heat exchanger by comparison between three controllers
LQR (linear quadratic regulator), PID (proportional, integrator and
derivate) and Pole Placement. All of these controllers are used mainly
in industrial sectors (chemicals, petrochemicals, steel, food
processing, energy production, etc…) of transportation (automotive,
aeronautics), but also in the residential sector and tertiary (heating, air
conditioning, etc...) The choice of a heat exchanger, for a given
application depends on many parameters: field temperature and
pressure of fluids, and physical properties of aggressive fluids,
maintenance and space. It is clear that the fact of having an
exchanger appropriate, well-sized, well made and well used allows
gain efficiency and energy processes.
Abstract: This paper deals with the novel intelligent bio-inspired control strategies, it presents a novel approach based on an optimal fuzzy immune PID parameters tuning, it is a combination of a PID controller, inspired by the human immune mechanism with fuzzy logic. Such controller offers more possibilities to deal with the delayed systems control difficulties due to the delay term. Indeed, we use an optimization approach to tune the four parameters of the controller in addition to the fuzzy function; the obtained controller is implemented in a modified Smith predictor structure, which is well known that it is the most efficient to the control of delayed systems. The application of the presented approach to control a three tank delay system shows good performances and proves the efficiency of the method.
Abstract: In order to study the performance of dynamic positioning system during S-lay operations, dynamic positioning system is simulated with the hull-stinger-pipe coupling effect. The roller of stinger is simulated by the generalized elastic contact theory. The stinger is composed of Morrison members. Force on pipe is calculated by lumped mass method. Time domain of fully coupled barge model is analyzed combining with PID controller, Kalman filter and allocation of thrust using Sequential Quadratic Programming method. It is also analyzed that the effect of hull wave frequency motion on pipe-stinger coupling force and dynamic positioning system. Besides, it is studied that how S-lay operations affect the dynamic positioning accuracy. The simulation results are proved to be available by checking pipe stress with API criterion. The effect of heave and yaw motion cannot be ignored on hull-stinger-pipe coupling force and dynamic positioning system. It is important to decrease the barge’s pitch motion and lay pipe in head sea in order to improve safety of the S-lay installation and dynamic positioning.
Abstract: This paper presents a differential evolution algorithm to design a robust PI and PID controllers for Load Frequency Control (LFC) of nonlinear interconnected power systems considering the boiler dynamics, Governor Dead Band (GDB), Generation Rate Constraint (GRC). Differential evolution algorithm is employed to search for the optimal controller parameters. The proposed method easily copes of with nonlinear constraints. Further the proposed controller is simple, effective and can ensure the desirable overall system performance. The superiority of the proposed approach has been shown by comparing the results with published fuzzy logic controller for the same power systems. The comparison is done using various performance measures like overshoot, settling time and standard error criteria of frequency and tie-line power deviation following a 1% step load perturbation in hydro area. It is noticed that, the dynamic performance of proposed controller is better than fuzzy logic controller. Furthermore, it is also seen that the proposed system is robust and is not affected by change in the system parameters.
Abstract: The Ambidextrous Robot Hand is a robotic device with the purpose to mimic either the gestures of a right or a left hand. The symmetrical behavior of its fingers allows them to bend in one way or another keeping a compliant and anthropomorphic shape. However, in addition to gestures they can reproduce on both sides, an asymmetrical mechanical design with a three tendons routing has been engineered to reduce the number of actuators. As a consequence, control algorithms must be adapted to drive efficiently the ambidextrous fingers from one position to another and to include grasping features. These movements are controlled by pneumatic muscles, which are nonlinear actuators. As their elasticity constantly varies when they are under actuation, the length of pneumatic muscles and the force they provide may differ for a same value of pressurized air. The control algorithms introduced in this paper take both the fingers asymmetrical design and the pneumatic muscles nonlinearity into account to permit an accurate control of the Ambidextrous Robot Hand. The finger motion is achieved by combining a classic PID controller with a phase plane switching control that turns the gain constants into dynamic values. The grasping ability is made possible because of a sliding mode control that makes the fingers adapt to the shape of an object before strengthening their positions.