Abstract: Flow around a flat tube is studied numerically. Reynolds number is defined base on equivalent circular tube and it is varied in range of 100 to 300. Equations are solved by using finite volume method and results are presented in form of drag and lift coefficient. Results show that drag coefficient of flat tube is up to 66% lower than circular tube with equivalent diameter. In addition, by increasing l/D from 1 to 2, the drag coefficient of flat tube is decreased about 14-27%.
Abstract: In order to be able to automatically differentiate
between two modes of permanent flow of a liquid simulating blood,
it was imperative to put together a data bank. Thus, the acquisition of
the various amplitude spectra of the Doppler signal of this liquid in
laminar flow and other spectra in turbulent flow enabled us to
establish an automatic difference between the two modes. According
to the number of parameters and their nature, a comparative study
allowed us to choose the best classifier.
Abstract: In the present analysis an unsteady laminar
forced convection water boundary layer flow is considered.
The fluid properties such as viscosity and Prandtl number are
taken as variables such that those are inversely proportional to
temperature. By using quasi-linearization technique the nonlinear
coupled partial differential equations are linearized and
the numerical solutions are obtained by using implicit finite
difference scheme with the appropriate selection of step sizes.
Non-similar solutions have been obtained from the starting
point of the stream-wise coordinate to the point where skin
friction value vanishes. The effect non-uniform mass transfer
along the surface of the cylinder through slot is studied on the
skin friction and heat transfer coefficients.
Abstract: The paper depicts air velocity values, reproduced by laser Doppler anemometer (LDA) and ultrasonic anemometer (UA), relations with calculated ones from flow rate measurements using the gas meter which calibration uncertainty is ± (0.15 – 0.30) %. Investigation had been performed in channel installed in aerodynamical facility used as a part of national standard of air velocity. Relations defined in a research let us confirm the LDA and UA for air velocity reproduction to be the most advantageous measures. The results affirm ultrasonic anemometer to be reliable and favourable instrument for measurement of mean velocity or control of velocity stability in the velocity range of 0.05 m/s – 10 (15) m/s when the LDA used. The main aim of this research is to investigate low velocity regularities, starting from 0.05 m/s, including region of turbulent, laminar and transitional air flows. Theoretical and experimental results and brief analysis of it are given in the paper. Maximum and mean velocity relations for transitional air flow having unique distribution are represented. Transitional flow having distinctive and different from laminar and turbulent flow characteristics experimentally have not yet been analysed.
Abstract: Cardiovascular disease mostly in the form of atherosclerosis is responsible for 30% of all world deaths amounting to 17 million people per year. Atherosclerosis is due to the formation of plaque. The fatty plaque may be at risk of rupture, leading typically to stroke and heart attack. The plaque is usually associated with a high degree of lumen reduction, called a stenosis. The initiation and progression of the disease is strongly linked to the hemodynamic environment near the vessel wall. The aim of this study is to validate the flow of blood mimic through an arterial stenosis model with computational fluid dynamics (CFD) package. In experiment, an axisymmetric model constructed consists of contraction and expansion region that follow a mathematical form of cosine function. A 30% diameter reduction was used in this study. Particle image velocimetry (PIV) was used to characterize the flow. The fluid consists of rigid spherical particles suspended in waterglycerol- NaCl mixture. The particles with 20 μm diameter were selected to follow the flow of fluid. The flow at Re=155, 270 and 390 were investigated. The experimental result is compared with FLUENT simulated flow that account for viscous laminar flow model. The results suggest that laminar flow model was sufficient to predict flow velocity at the inlet but the velocity at stenosis throat at Re =390 was overestimated. Hence, a transition to turbulent regime might have been developed at throat region as the flow rate increases.
Abstract: Three dimensional simulations in tube in tube heat
exchangers are investigated numerically in this study. In these
simulations forced convective heat transfer and laminar flow of
single-phase water are considered. In order to measure heat transfer
parameters in these heat exchangers, FLUENT CFD Solver is used in
this numerical method. For the purpose of creating geometry and
exert boundary and initial conditions in the present model, finite
volume method in Computational Fluid Dynamics is used in this
study. In the present study, at each Z-location, variation of local
temperatures, heat flux and Nusselt number at the whole tube is
investigated in detail. Thereafter, averaged computational Nusselt
number in this model is calculated. In addition, conceivable pressure
drops have been obtained at each Z-location in this model. Then,
pressure drop values in the present model are explored. Finally, all
the numerical results for this kind of heat exchanger will be discussed
precisely.
Abstract: This paper is a numerical investigation of a laminar
isothermal plane two dimensional wall jet. Special attention has been
paid to the effect of the inlet conditions at the nozzle exit on the
hydrodynamic and thermal characteristics of the flow. The
behaviour of various fluids evolving in both forced and mixed
convection regimes near a vertical plate plane is carried out. The
system of governing equations is solved with an implicit finite
difference scheme. For numerical stability we use a staggered non
uniform grid. The obtained results show that the effect of the Prandtl
number is significant in the plume region in which the jet flow is
governed by buoyant forces. Further for ascending X values, the
buoyancy forces become dominating, and a certain agreement
between the temperature profiles are observed, which shows that the
velocity profile has no longer influence on the wall temperature
evolution in this region. Fluids with low Prandtl number warm up
more importantly, because for such fluids the effect of heat diffusion
is higher.
Abstract: In this study, numerical simulations on laminar flow in
sinusoidal wavy shaped tubes were conducted for mean Reynolds
number of 250, which is in the range of physiological flow-rate and
investigated flow structures, pressure distribution and particle
trajectories both in steady and periodic inflow conditions. For
extensive comparisons, various wave lengths and amplitudes of sine
function for geometry of tube models were employed. The results
showed that small amplitude secondary curvature has significant
influence on the nature of flow patterns and particle mixing
mechanism. This implies that characterizing accurate geometry is
essential in accurate predicting of in vivo hemodynamics and may
motivate further study on any possibility of reflection of secondary
flow on vascular remodeling and pathophysiology.
Abstract: This paper discusses the utilization of marine biomass as an energy resource in Japan. A marine biomass energy system in Japan was proposed consisting of seaweed cultivation (Laminaria japonica) at offshore marine farms, biogas production via methane fermentation of the seaweeds, and fuel cell power generation driven by the generated biogas. We estimated energy output, energy supply potential, and CO2 mitigation in Japan on the basis of the proposed system. As a result, annual energy production was estimated to be 1.02-109 kWh/yr at nine available sites. Total CO2 mitigation was estimated to be 1.04-106 tonnes per annum at the nine sites. However, the CO2 emission for the construction of relevant facilities is not taken into account in this paper. The estimated CO2 mitigation is equivalent to about 0.9% of the required CO2 mitigation for Japan per annum under the Kyoto Protocol framework.
Abstract: This paper analyses the unsteady, two-dimensional
stagnation point flow of an incompressible viscous fluid over a flat
sheet when the flow is started impulsively from rest and at the same
time, the sheet is suddenly stretched in its own plane with a velocity
proportional to the distance from the stagnation point. The partial
differential equations governing the laminar boundary layer forced
convection flow are non-dimensionalised using semi-similar
transformations and then solved numerically using an implicit finitedifference
scheme known as the Keller-box method. Results
pertaining to the flow and heat transfer characteristics are computed
for all dimensionless time, uniformly valid in the whole spatial region
without any numerical difficulties. Analytical solutions are also
obtained for both small and large times, respectively representing the
initial unsteady and final steady state flow and heat transfer.
Numerical results indicate that the velocity ratio parameter is found
to have a significant effect on skin friction and heat transfer rate at
the surface. Furthermore, it is exposed that there is a smooth
transition from the initial unsteady state flow (small time solution) to
the final steady state (large time solution).
Abstract: This paper presents a numerical study on surface heat
transfer characteristics of laminar air flows in parallel-plate dimpled
channels. The two-dimensional numerical model is provided by
commercial code FLUENT and the results are obtained for channels
with symmetrically opposing hemi-cylindrical cavities onto both
walls for Reynolds number ranging from 1000 to 2500. The influence
of variations in relative depth of dimples (the ratio of cavity depth to
the cavity curvature diameter), the number of them and the thermophysical
properties of channel walls on heat transfer enhancement is
studied. The results are evident for existence of an optimum value for
the relative depth of dimples in which the largest wall heat flux and
average Nusselt number can be achieved. In addition, the results of
conjugation simulation indicate that the overall influence of the ratio
of wall thermal conductivity to the one of the fluid on heat transfer
rate is not much significant and can be ignored.
Abstract: This paper investigates the nature of the development
of two-dimensional laminar flow of an incompressible fluid at the
reversed stagnation-point. ". In this study, we revisit the problem
of reversed stagnation-point flow over a flat plate. Proudman and
Johnson (1962) first studied the flow and obtained an asymptotic
solution by neglecting the viscous terms. This is no true in neglecting
the viscous terms within the total flow field. In particular it is pointed
out that for a plate impulsively accelerated from rest to a constant
velocity V0 that a similarity solution to the self-similar ODE is
obtained which is noteworthy completely analytical.
Abstract: In this paper delamination phenomenon in
Carbon-Epoxy laminated composite material is investigated
numerically. Arcan apparatus and specimen is modeled in ABAQUS
finite element software for different loading conditions and crack
geometries. The influence of variation of crack geometry on
interlaminar fracture stress intensity factor and energy release rate for
various mixed mode ratios and pure mode I and II was studied. Also,
correction factors for this specimen for different crack length ratios
were calculated. The finite element results indicate that for loading
angles close to pure mode-II loading, a high ratio of mode-II to
mode-I fracture is dominant and there is an opposite trend for loading
angles close to pure mode-I loading. It confirms that by varying the
loading angle of Arcan specimen pure mode-I, pure mode-II and a
wide range of mixed-mode loading conditions can be created and
tested. Also, numerical results confirm that the increase of the mode-
II loading contribution leads to an increase of fracture resistance in
the CF/PEI composite (i.e., a reduction in the total strain energy
release rate) and the increase of the crack length leads to a reduction
of interlaminar fracture resistance in the CF/PEI composite (i.e., an
increase in the total interlaminar strain energy release rate).
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Abstract: We have measured the pressure drop and convective
heat transfer coefficient of water – based AL(25nm),AL2O3(30nm)
and CuO(50nm) Nanofluids flowing through a uniform heated
circular tube in the fully developed laminar flow regime. The
experimental results show that the data for Nanofluids friction factor
show a good agreement with analytical prediction from the Darcy's
equation for single-phase flow. After reducing the experimental
results to the form of Reynolds, Rayleigh and Nusselt numbers. The
results show the local Nusselt number and temperature have
distribution with the non-dimensional axial distance from the tube
entry. Study decided that thenNanofluid as Newtonian fluids through
the design of the linear relationship between shear stress and the rate
of stress has been the study of three chains of the Nanofluid with
different concentrations and where the AL, AL2O3 and CuO – water
ranging from (0.25 - 2.5 vol %). In addition to measuring the four
properties of the Nanofluid in practice so as to ensure the validity of
equations of properties developed by the researchers in this area and
these properties is viscosity, specific heat, and density and found that
the difference does not exceed 3.5% for the experimental equations
between them and the practical. The study also demonstrated that the
amount of the increase in heat transfer coefficient for three types of
Nano fluid is AL, AL2O3, and CuO – Water and these ratios are
respectively (45%, 32%, 25%) with insulation and without insulation
(36%, 23%, 19%), and the statement of any of the cases the best
increase in heat transfer has been proven that using insulation is
better than not using it. I have been using three types of Nano
particles and one metallic Nanoparticle and two oxide Nanoparticle
and a statement, whichever gives the best increase in heat transfer.
Abstract: Solid fuel transient burning behavior under oxidizer
gas flow is numerically investigated. It is done using analysis of the
regression rate responses to the imposed sudden and oscillatory
variation at inflow properties. The conjugate problem is considered
by simultaneous solution of flow and solid phase governing
equations to compute the fuel regression rate. The advection
upstream splitting method is used as flow computational scheme in
finite volume method. The ignition phase is completely simulated to
obtain the exact initial condition for response analysis. The results
show that the transient burning effects which lead to the combustion
instabilities and intermittent extinctions could be observed in solid
fuels as the solid propellants.
Abstract: In the present study, fracture behavior of woven
fabric-reinforced glass/epoxy composite laminates under mode III
crack growth was experimentally investigated and numerically
modeled. Two methods were used for the calculation of the strain
energy release rate: the experimental compliance calibration (CC)
method and the Virtual Crack Closure Technique (VCCT). To
achieve this aim ECT (Edge Crack Torsion) was used to evaluate
fracture toughness in mode III loading (out of plane-shear) at
different crack lengths. Load–displacement and associated energy
release rates were obtained for various case of interest. To
calculate fracture toughness JIII, two criteria were considered
including non-linearity and maximum points in load-displacement
curve and it is observed that JIII increases with the crack length
increase. Both the experimental compliance method and the virtual
crack closure technique proved applicable for the interpretation of the
fracture mechanics data of woven glass/epoxy laminates in mode III.
Abstract: Combustion of sprays is of technological importance, but its flame behavior is not fully understood. Furthermore, the multiplicity of dependent variables such as pressure, temperature, equivalence ratio, and droplet sizes complicates the study of spray combustion. Fundamental study on the influence of the presence of liquid droplets has revealed that laminar flames within aerosol mixtures more readily become unstable than for gaseous ones and this increases the practical burning rate. However, fundamental studies on turbulent flames of aerosol mixtures are limited particularly those under near mono-dispersed droplet conditions. In the present work, centrally ignited expanding flames at near atmospheric pressures are employed to quantify the burning rates in gaseous and aerosol flames. Iso-octane-air aerosols are generated by expansion of the gaseous pre-mixture to produce a homogeneously distributed suspension of fuel droplets. The effects of the presence of droplets and turbulence velocity in relation to the burning rates of the flame are also investigated.
Abstract: Incompressible Navier-Stokes equations are reviewed
in this work. Three-dimensional Navier-Stokes equations are solved
analytically. The Mathematical derivation shows that the solutions
for the zero and constant pressure gradients are similar. Descriptions
of the proposed formulation and validation against two laminar
experiments and three different turbulent flow cases are reported in
this paper. Even though, the analytical solution is derived for nonreacting
flows, it could reproduce trends for cases including
combustion.
Abstract: Delamination between layers in composite materials is a major structural failure. The delamination resistance is quantified by the critical strain energy release rate (SERR). The present investigation deals with the strain energy release rate of two woven fabric composites. Materials used are made of two types of glass fiber (360 gsm and 600 gsm) of plain weave and epoxy as matrix. The fracture behavior is studied using the mode I, double cantilever beam test and the mode II, end notched flexure test, in order to determine the energy required for the initiation and growth of an artificial crack. The delamination energy of these two materials is compared in order to study the effect of weave and reinforcement on mechanical properties. The fracture mechanism is also analyzed by means of scanning electron microscopy (SEM). It is observed that the plain weave fabric composite with lesser strand width has higher inter laminar fracture properties compared to the plain weave fabric composite with more strand width.