Abstract: In an original directed diffusion routing protocol, a sink requests sensing data from a source node by flooding interest messages to the network. Then, the source finds the sink by sending exploratory data messages to all nodes that generate incoming interest messages. This protocol signaling can cause heavy traffic in the network, an interference of the radio signal, collisions, great energy consumption of sensor nodes, etc. According to this research problem, this paper investigates the effect of sending interest and exploratory data messages on the performance of directed diffusion routing protocol. We demonstrate the research problem occurred from employing directed diffusion protocol in mobile wireless environments. For this purpose, we perform a set of experiments by using NS2 (network simulator 2). The radio propagation models; Two-ray ground reflection with and without shadow fading are included to investigate the effect of signaling. The simulation results show that the number of times of sent and received protocol signaling in the case of sending interest and exploratory data messages are larger than the case of sending other protocol signals, especially in the case of shadowing model. Additionally, the number of exploratory data message is largest in one round of the protocol procedure.
Abstract: There are various sources of energies available
worldwide and among them, crude oil plays a vital role. Oil recovery
is achieved using conventional primary and secondary recovery
methods. In-order to recover the remaining residual oil, technologies
like Enhanced Oil Recovery (EOR) are utilized which is also known
as tertiary recovery. Among EOR, Microbial enhanced oil recovery
(MEOR) is a technique which enables the improvement of oil
recovery by injection of bio-surfactant produced by microorganisms.
Bio-surfactant can retrieve unrecoverable oil from the cap rock which
is held by high capillary force. Bio-surfactant is a surface active agent
which can reduce the interfacial tension and reduce viscosity of oil
and thereby oil can be recovered to the surface as the mobility of the
oil is increased. Research in this area has shown promising results
besides the method is echo-friendly and cost effective compared with
other EOR techniques. In our research, on laboratory scale we
produced bio-surfactant using the strain Pseudomonas putida (MTCC
2467) and injected into designed simple sand packed column which
resembles actual petroleum reservoir. The experiment was conducted
in order to determine the efficiency of produced bio-surfactant in oil
recovery. The column was made of plastic material with 10 cm in
length. The diameter was 2.5 cm. The column was packed with fine
sand material. Sand was saturated with brine initially followed by oil
saturation. Water flooding followed by bio-surfactant injection was
done to determine the amount of oil recovered. Further, the injection
of bio-surfactant volume was varied and checked how effectively oil
recovery can be achieved. A comparative study was also done by
injecting Triton X 100 which is one of the chemical surfactant. Since,
bio-surfactant reduced surface and interfacial tension oil can be easily
recovered from the porous sand packed column.
Abstract: Remote sensing image processing, spatial data analysis through GIS approach, and analytical hierarchy process were introduced in this study for assessing the vulnerability area and inundation area due to tsunami hazard in the area of Rikuzentakata, Iwate Prefecture, Japan. Appropriate input parameters were derived from GSI DEM data, ALOS AVNIR-2, and field data. We used the parameters of elevation, slope, shoreline distance, and vegetation density. Five classes of vulnerability were defined and weighted via pairwise comparison matrix. The assessment results described that 14.35km2 of the study area was under tsunami vulnerability zone. Inundation areas are those of high and slightly high vulnerability. The farthest area reached by a tsunami was about 7.50km from the shoreline and shows that rivers act as flooding strips that transport tsunami waves into the hinterland. This study can be used for determining a priority for land-use planning in the scope of tsunami hazard risk management.
Abstract: This work concerns on experimentally investigation
of surfactant flooding in fractured porous media. In this study a series
of water and surfactant injection processes were performed on
micromodels initially saturated with a heavy crude oil. Eight
fractured glass micromodels were used to illustrate effects of
surfactant types and concentrations on oil recovery efficiency in
presence of fractures with different properties i.e. fracture
orientation, length and number of fractures. Two different
surfactants with different concentrations were tested. The results
showed that surfactant flooding would be more efficient by using
SDS surfactant aqueous solution and also by locating injection well
in a proper position respect to fracture properties. This study
demonstrates different physical and chemical conditions that affect
the efficiency of this method of enhanced oil recovery.
Abstract: Ice cover County has a significant impact on rivers as it affects with the ice melting capacity which results in flooding, restrict navigation, modify the ecosystem and microclimate. River ices are made up of different ice types with varying ice thickness, so surveillance of river ice plays an important role. River ice types are captured using infrared imaging camera which captures the images even during the night times. In this paper the river ice infrared texture images are analysed using first-order statistical methods and secondorder statistical methods. The second order statistical methods considered are spatial gray level dependence method, gray level run length method and gray level difference method. The performance of the feature extraction methods are evaluated by using Probabilistic Neural Network classifier and it is found that the first-order statistical method and second-order statistical method yields low accuracy. So the features extracted from the first-order statistical method and second-order statistical method are combined and it is observed that the result of these combined features (First order statistical method + gray level run length method) provides higher accuracy when compared with the features from the first-order statistical method and second-order statistical method alone.
Abstract: Use of microemulsion in enhanced oil recovery has become more attractive in recent years because of its high level of extraction efficiency. Experimental investigations have been made on characterization of microemulsions of oil-brinesurfactant/ cosurfactant system for its use in enhanced oil recovery (EOR). Sodium dodecyl sulfate, propan-1-ol and heptane were selected as surfactant, cosurfactant and oil respectively for preparation of microemulsion. The effects of salinity on the relative phase volumes and solubilization parameters have also been studied. As salinity changes from low to high value, phase transition takes place from Winsor I to Winsor II via Winsor III. Suitable microemulsion composition has been selected based on its stability and ability to reduce interfacial tension. A series of flooding experiments have been performed using the selected microemulsion. The flooding experiments were performed in a core flooding apparatus using uniform sand pack. The core holder was tightly packed with uniform sands (60-100 mesh) and saturated with brines of different salinities. It was flooded with the brine at 25 psig and the absolute permeability was calculated from the flow rate of the through sand pack. The sand pack was then flooded with the crude oil at 800 psig to irreducible water saturation. The initial water saturation was determined on the basis of mass balance. Waterflooding was conducted by placing the coreholder horizontally at a constant injection pressure at 200 pisg. After water flooding, when water-cut reached above 95%, around 0.5 pore volume (PV) of the above microemulsion slug was injected followed by chasing water. The experiments were repeated using different composition of microemulsion slug. The additional recoveries were calculated by material balance. Encouraging results with additional recovery more than 20% of original oil in place above the conventional water flooding have been observed.
Abstract: There are various overlay structures that provide
efficient and scalable solutions for point and range query in a peer-topeer
network. Overlay structure based on m-Binary Search Tree
(BST) is one such popular technique. It deals with the division of the
tree into different key intervals and then assigning the key intervals to
a BST. The popularity of the BST makes this overlay structure
vulnerable to different kinds of attacks. Here we present four such
possible attacks namely index poisoning attack, eclipse attack,
pollution attack and syn flooding attack. The functionality of BST is
affected by these attacks. We also provide different security
techniques that can be applied against these attacks.
Abstract: Permeability reduction induced by asphaltene
precipitation during gas injection is one of the serious problems in
the oil industry. This problem can lead to formation damage and
decrease the oil production rate. In this work, Malaysian light oil
sample has been used to investigate the effect CO2 injection and
Water Alternating Gas (WAG) injection on permeability reduction.
In this work, dynamic core flooding experiments were conducted to
study the effect of CO2 and WAG injection on the amount of
asphaltene precipitated. Core properties after displacement were
inspected for any permeability reduction to study the effect of
asphaltene precipitation on rock properties.
The results showed that WAG injection gave less asphaltene
precipitation and formation damage compared to CO2 injection. The
study suggested that WAG injection can be one of the important
factors of managing asphaltene precipitation.
Abstract: Spray chilling using air-mist nozzles has received
much attention in the food processing industry because of the
benefits it has shown over forced air convection. These benefits
include an increase in the heat transfer coefficient and a reduction in
the water loss by the product during cooling. However, few studies
have simulated the heat transfer and aerodynamics phenomena of the
air-mist chilling process for optimal operating conditions. The study
provides insight into the optimal conditions for spray impaction, heat
transfer efficiency and control of surface flooding. A computational
fluid dynamics model using a two-phase flow composed of water
droplets injected with air is developed to simulate the air-mist
chilling of food products. The model takes into consideration
droplet-to-surface interaction, water-film accumulation and surface
runoff. The results of this study lead to a better understanding of the
heat transfer enhancement, water conservation, and to a clear
direction for the optimal design of air-mist chilling systems that can
be used in commercial applications in the food and meat processing
industries.
Abstract: Saffron (Crocus sativus) is cultivated as spices,
medicinal and aromatic plant species. At autumn season, heavy
rainfall can cause flooding stress and inhibits growth of saffron. Thus
this research was conducted to study the effect of silver ion (as an
ethylene inhibitor) on growth of saffron under flooding conditions.
The corms of saffron were soaked with one concentration of nano
silver (0, 40, 80 or 120 ppm) and then planting under flooding stress
or non flooding stress conditions. Results showed that number of
roots, root length, root fresh and dry weight, leaves fresh and dry
weight were reduced by 10 day flooding stress. Soaking saffron
corms with 40 or 80 ppm concentration of nano silver rewarded the
effect of flooding stress on the root number, by increasing it.
Furthermore, 40 ppm of nano silver increased root length in stress.
Nano silver 80 ppm in flooding stress, increased leaves dry weight.
Abstract: The lack of any centralized infrastructure in mobile ad
hoc networks (MANET) is one of the greatest security concerns in
the deployment of wireless networks. Thus communication in
MANET functions properly only if the participating nodes cooperate
in routing without any malicious intention. However, some of the
nodes may be malicious in their behavior, by indulging in flooding
attacks on their neighbors. Some others may act malicious by
launching active security attacks like denial of service. This paper
addresses few related works done on trust evaluation and
establishment in ad hoc networks. Related works on flooding attack
prevention are reviewed. A new trust approach based on the extent of
friendship between the nodes is proposed which makes the nodes to
co-operate and prevent flooding attacks in an ad hoc environment.
The performance of the trust algorithm is tested in an ad hoc network
implementing the Ad hoc On-demand Distance Vector (AODV)
protocol.
Abstract: Network on a chip (NoC) has been proposed as a viable solution to counter the inefficiency of buses in the current VLSI on-chip interconnects. However, as the silicon chip accommodates more transistors, the probability of transient faults is increasing, making fault tolerance a key concern in scaling chips. In packet based communication on a chip, transient failures can corrupt the data packet and hence, undermine the accuracy of data communication. In this paper, we present a comparative analysis of transient fault tolerant techniques including end-to-end, node-by-node, and stochastic communication based on flooding principle.
Abstract: The effect of flooding can be a serious problem for
wheat farmers, even at dry land condition. Amount of flooding
damage depends on duration flooding, developmental stage, wheat
type and variety. Therefore as a factorial experiment in randomized
complete design based on winter bread wheat cultivars (Pishtaz,
Marvdasht, Shiraz, Zarin, Shahriar, C-81-4, Sardari, Agosta seed,
FGS and Azar2) at stages (Non- flooding stress, flooding at tillering
and stem elongation stages for 15 days) carried out in Faculty of
Agriculture, Razi University, Kermanshah, Iran. During flooding,
soil environment of plant roots were water saturated. Analysis of
variance showed that flooding had a significant effect on the number
of grains per spike, grain weight per spike and a grain weight. Hence
flooding reduces the number of grain per spike between 27.1 to 42.5
percent, grain weight per spike between 34.7 to 54.4 percent and
single grain weight between 12.1 to 15.1 percent. Effects of flooding
at the tillering stage reduced higher than stem elongation stage on
studied traits. The result also showed that flooding at tillering stage
delayed spikelet primordial and floret. Between wheat cultivars was
significant for traits, but were different reactions. "Shiraz", "Zarin"
and "Shahriar" had the most no. grain per spike, but "Zarin" and
"Sardari" had the most grain weight per spike and single grain
weight, respectively. Also, interaction between start of flooding and
cultivar was significant.
Abstract: Nanoemulsions are a class of emulsions with a droplet
size in the range of 50–500 nm and have attracted a great deal of
attention in recent years because it is unique characteristics. The
physicochemical properties of nanoemulsion suggests that it can be
successfully used to recover the residual oil which is trapped in the
fine pore of reservoir rock by capillary forces after primary and
secondary recovery. Oil-in-water nanoemulsion which can be formed
by high-energy emulsification techniques using specific surfactants
can reduce oil-water interfacial tension (IFT) by 3-4 orders of
magnitude. The present work is aimed on characterization of oil-inwater
nanoemulsion in terms of its phase behavior, morphological
studies; interfacial energy; ability to reduce the interfacial tension and
understanding the mechanisms of mobilization and displacement of
entrapped oil blobs by lowering interfacial tension both at the
macroscopic and microscopic level. In order to investigate the
efficiency of oil-water nanoemulsion in enhanced oil recovery
(EOR), experiments were performed to characterize the emulsion in
terms of their physicochemical properties and size distribution of the
dispersed oil droplet in water phase. Synthetic mineral oil and a series
of surfactants were used to prepare oil-in-water emulsions.
Characterization of emulsion shows that it follows pseudo-plastic
behaviour and drop size of dispersed oil phase follows lognormal
distribution. Flooding experiments were also carried out in a
sandpack system to evaluate the effectiveness of the nanoemulsion as
displacing fluid for enhanced oil recovery. Substantial additional
recoveries (more than 25% of original oil in place) over conventional
water flooding were obtained in the present investigation.
Abstract: Non-uniform current distribution in polymer
electrolyte membrane fuel cells results in local over-heating,
accelerated ageing, and lower power output than expected. This
issue is very critical when fuel cell experiences water flooding. In
this work, the performance of a PEM fuel cell is investigated under
cathode flooding conditions. Two-dimensional partially flooded
GDL models based on the conservation laws and electrochemical
relations are proposed to study local current density distributions
along flow fields over a wide range of cell operating conditions.
The model results show a direct association between cathode inlet
humidity increases and that of average current density but the
system becomes more sensitive to flooding. The anode inlet
relative humidity shows a similar effect. Operating the cell at
higher temperatures would lead to higher average current densities
and the chance of system being flooded is reduced. In addition,
higher cathode stoichiometries prevent system flooding but the
average current density remains almost constant. The higher anode
stoichiometry leads to higher average current density and higher
sensitivity to cathode flooding.
Abstract: In this work, several ASP solutions were flooded into
fractured models initially saturated with heavy oil at a constant flow
rate and different geometrical characteristics of fracture. The ASP
solutions are constituted from 2 polymers i.e. a synthetic polymer,
hydrolyzed polyacrylamide as well as a biopolymer, a surfactant and
2types of alkaline. The results showed that using synthetic
hydrolyzed polyacrylamide polymer increases ultimate oil recovery;
however, type of alkaline does not play a significant rule on oil
recovery. In addition, position of the injection well respect to the
fracture system has remarkable effects on ASP flooding. For instance
increasing angle of fractures with mean flow direction causes more
oil recovery and delays breakthrough time. This work can be
accounted as a comprehensive survey on ASP flooding which
considers most of effective factors in this chemical EOR method.
Abstract: In this work, the precipitation of asphaltene from a Malaysian light oil reservoir was studies. A series of experiments were designed and carried out to examine the effect of CO2 injection on asphaltene precipitation. Different pressures of injections were used in Dynamic flooding experiment in order to investigate the effect of pressure versus injection pore volume of CO2. These dynamic displacement tests simulate reservoir condition. Results show that by increasing the pore volume of injected gas asphaltene precipitation will increases, also rise in injection pressure causes less precipitation. Sandstone core plug was used to represent reservoir formation during displacement test; therefore it made it possible to study the effect of present of asphaltene on formation. It is found out that the precipitated asphaltene can reduce permeability and porosity which is not favorable during oil production.
Abstract: Laser Profiler (LP) data from aerial laser surveys have
been increasingly used as topographical inputs to numerical
simulations of flooding and inundation in river basins. LP data has
great potential for reproducing topography, but its effective usage has
not yet been fully established. In this study, flooding and inundation
are simulated numerically using LP data for the Jobaru River basin of
Japan’s Saga Plain. The analysis shows that the topography is
reproduced satisfactorily in the computational domain with urban and
agricultural areas requiring different grid sizes. A 2-D numerical
simulation shows that flood flow behavior changes as grid size is
varied.
Abstract: An experiment was conducted on the comparative
study of drip and furrow irrigation methods at the farmer-s field in
Umar Kot. The total area under experiment about 4000m2 was
divided into two equal portions. One portion about 40m X 50m was
occupied by drip and the other portion about 40m X 50m by furrow
irrigation method. Soil at the experimental site was clay loam in
texture for 0-60cm depth; average dry bulk density and field capacity
was 1.16g/cm3 and 28.5% respectively. The results reveal that the
drip irrigation method saved 56.4% water and gave 22% more yield
as compared to that of furrow irrigation method. Higher water use
efficiency about 4.87 was obtained in drip irrigation method; whereas
lower water used efficiency about 1.66 was obtained in furrow
irrigation method. The present study suggests farming community to
adopt drip irrigation method instead of old traditional flooding
methods.
Abstract: The objective of this work is to present a expertise on
flooding hazard analysis and how to reduce the risk. The analysis
concerns the disaster induced by the flood on November 10/11, 2001
in the Bab El Oued district of the city of Algiers.The study begins by
an expertise of damages in related with the urban environment and
the history of the urban growth of the site. After this phase, the work
is focalized on the identification of the existing correlations between
the development of the town and its vulnerability. The final step
consists to elaborate the interpretations on the interactions between
the urban growth, the sewerage network and the vulnerability of the
urban system.In conclusion, several recommendations are formulated
permitting the mitigation of the risk in the future. The principal
recommendations concern the new urban operations and the existing
urbanized sites.