Abstract: Laminar natural-convective heat transfer from a
horizontal cylinder is studied by solving the Navier-Stokes and
energy equations using higher order compact scheme in cylindrical
polar coordinates. Results are obtained for Rayleigh numbers of 1,
10, 100 and 1000 for a Prandtl number of 0.7. The local Nusselt
number and mean Nusselt number are calculated and compared with
available experimental and theoretical results. Streamlines, vorticity -
lines and isotherms are plotted.
Abstract: Two-dimensional heat conduction within a composed solid material with a constant internal heat generation has been investigated numerically in a sector of the rotor a generator. The heat transfer between two adjacent materials is assumed to be purely conduction. Boundary conditions are assumed to be forced convection on the fluid side and adiabatic on symmetry lines. The control volume method is applied for the diffusion energy equation. Physical coordinates are transformed to the general curvilinear coordinates. Then by using a line-by-line method, the temperature distribution in a sector of the rotor has been determined. Finally, the results are normalized and the effect of cooling fluid on the maximum temperature of insulation is investigated.
Abstract: The aim of this paper is to investigate twodimensional unsteady flow of a viscous incompressible fluid about stagnation point on permeable stretching sheet in presence of time dependent free stream velocity. Fluid is considered in the influence of transverse magnetic field in the presence of radiation effect. Rosseland approximation is use to model the radiative heat transfer. Using time-dependent stream function, partial differential equations corresponding to the momentum and energy equations are converted into non-linear ordinary differential equations. Numerical solutions of these equations are obtained by using Runge-Kutta Fehlberg method with the help of Newton-Raphson shooting technique. In the present work the effect of unsteadiness parameter, magnetic field parameter, radiation parameter, stretching parameter and the Prandtl number on flow and heat transfer characteristics have been discussed. Skin-friction coefficient and Nusselt number at the sheet are computed and discussed. The results reported in the paper are in good agreement with published work in literature by other researchers.
Abstract: The forced convection heat transfer in high porosity metal-foam filled tube heat exchangers are studied in this paper. The Brinkman Darcy momentum model and two energy equations for both solid and fluid phases in porous media are employed .The study shows that using metal-foams can significantly improve the heat transfer in heat exchangers.
Abstract: Natural convection heat transfer from a heated
horizontal semi-circular cylinder (flat surface upward) has been
investigated for the following ranges of conditions; Grashof number,
and Prandtl number. The governing partial differential equations
(continuity, Navier-Stokes and energy equations) have been solved
numerically using a finite volume formulation. In addition, the role of
the type of the thermal boundary condition imposed at cylinder
surface, namely, constant wall temperature (CWT) and constant heat
flux (CHF) are explored. Natural convection heat transfer from a
heated horizontal semi-circular cylinder (flat surface upward) has
been investigated for the following ranges of conditions; Grashof
number, and Prandtl number, . The governing partial differential
equations (continuity, Navier-Stokes and energy equations) have
been solved numerically using a finite volume formulation. In
addition, the role of the type of the thermal boundary condition
imposed at cylinder surface, namely, constant wall temperature
(CWT) and constant heat flux (CHF) are explored. The resulting flow
and temperature fields are visualized in terms of the streamline and
isotherm patterns in the proximity of the cylinder. The flow remains
attached to the cylinder surface over the range of conditions spanned
here except that for and ; at these conditions, a separated flow
region is observed when the condition of the constant wall
temperature is prescribed on the surface of the cylinder. The heat
transfer characteristics are analyzed in terms of the local and average
Nusselt numbers. The maximum value of the local Nusselt number
always occurs at the corner points whereas it is found to be minimum
at the rear stagnation point on the flat surface. Overall, the average
Nusselt number increases with Grashof number and/ or Prandtl
number in accordance with the scaling considerations. The numerical
results are used to develop simple correlations as functions of
Grashof and Prandtl number thereby enabling the interpolation of the
present numerical results for the intermediate values of the Prandtl or
Grashof numbers for both thermal boundary conditions.
Abstract: The RANS method with Saffman-s turbulence model
was employed to solve the time-dependent turbulent Navier-Stokes
and energy equations for oscillating pipe flows. The method of
partial sums of the Fourier series is used to analyze the harmonic
velocity and temperature results. The complete structures of the
oscillating pipe flows and the averaged Nusselt numbers on the tube
wall are provided by numerical simulation over wide ranges of ReA
and ReR. Present numerical code is validated by comparing the
laminar flow results to analytic solutions and turbulence flow results
to published experimental data at lower and higher Reynolds
numbers respectively. The effects of ReA and ReR on the velocity,
temperature and Nusselt number distributions have been di scussed.
The enhancement of the heat transfer due to oscillating flows has
also been presented. By the way of analyzing the overall Nusselt
number over wide ranges of the Reynolds number Re and Keulegan-
Carpenter number KC, the optimal ratio of the tube diameter over
the oscillation amplitude is obtained based on the existence of a
nearly constant optimal KC number. The potential application of the
present results in sea water cooling has also been discussed.
Abstract: Axial Flux Permanent Magnet (AFPM) Machines require effective cooling due to their high power density. The detrimental effects of overheating such as degradation of the insulation materials, magnets demagnetization, and increase of Joule losses are well known. This paper describes the CFD simulations performed on a test rig model of an air cooled Axial Flux Permanent Magnet (AFPM) generator built at Durham University to identify the temperatures and heat transfer coefficient on the stator. The Reynolds Averaged Navier-Stokes and the Energy equations are solved and the flow pattern and heat transfer developing inside the machine are described. The Nusselt number on the stator surfaces has been found. The dependency of the heat transfer on the flow field is described temperature field obtained. Tests on an experimental are undergoing in order to validate the CFD results.
Abstract: In this work we study analytically and numerically the
performance of the mean heave motion of an OWC coupled with the
governing equation of the spreading ocean waves due to the wide
variation in an open parabolic channel with constant depth. This
paper considers that the ocean wave propagation is under the
assumption of a shallow flow condition. In order to verify the effect
of the waves in the OWC firstly we establish the analytical model in
a non-dimensional form based on the energy equation. The proposed
wave-power system has to aims: one is to perturb the ocean waves as
a consequence of the channel shape in order to concentrate the
maximum ocean wave amplitude in the neighborhood of the OWC
and the second is to determine the pressure and volume oscillation of
air inside the compression chamber.
Abstract: This article attempts to analyze functionally graded beam thermal buckling along with piezoelectric layers applying based on the third order shearing deformation theory considering various boundary conditions. The beam properties are assumed to vary continuously from the lower surface to the upper surface of the beam. The equilibrium equations are derived using the total potential energy equations, Euler equations, piezoelectric material constitutive equations and third order shear deformation theory assumptions. In order to fulfill such an aim, at first functionally graded beam with piezoelectric layers applying the third order shearing deformation theory along with clamped -clamped boundary conditions are thoroughly analyzed, and then following making sure of the correctness of all the equations, the very same beam is analyzed with piezoelectric layers through simply-simply and simply-clamped boundary conditions. In this article buckling critical temperature for functionally graded beam is derived in two different ways, without piezoelectric layer and with piezoelectric layer and the results are compared together. Finally, all the conclusions obtained will be compared and contrasted with the same samples in the same and distinguished conditions through tables and charts. It would be noteworthy that in this article, the software MAPLE has been applied in order to do the numeral calculations.
Abstract: A numerical study has been carried out to investigate
the heat transfer by natural convection of nanofluid taking Cu as
nanoparticles and the water as based fluid in a three dimensional
annulus enclosure filled with porous media (silica sand) between two
horizontal concentric cylinders with 12 annular fins of 2.4mm
thickness attached to the inner cylinder under steady state conditions.
The governing equations which used are continuity, momentum and
energy equations under an assumptions used Darcy law and
Boussinesq-s approximation which are transformed to dimensionless
equations. The finite difference approach is used to obtain all the
computational results using the MATLAB-7. The parameters affected
on the system are modified Rayleigh number (10 ≤Ra*≤ 1000), fin
length Hf (3, 7 and 11mm), radius ratio Rr (0.293, 0.365 and 0.435)
and the volume fraction(0 ≤ ¤ò ≤ 0 .35). It was found that the
average Nusselt number depends on (Ra*, Hf, Rr and φ). The results
show that, increasing of fin length decreases the heat transfer rate and
for low values of Ra*, decreasing Rr cause to decrease Nu while for
Ra*
greater than 100, decreasing Rr cause to increase Nu and adding
Cu nanoparticles with 0.35 volume fraction cause 27.9%
enhancement in heat transfer. A correlation for Nu in terms of Ra*,
Hf and φ, has been developed for inner hot cylinder.
Abstract: The steady incompressible flow has been solved in cylindrical coordinates in both vapour region and wick structure. The governing equations in vapour region are continuity, Navier-Stokes and energy equations. These equations have been solved using SIMPLE algorithm. For study of parameters variation on heat pipe operation, a benchmark has been chosen and the effect of changing one parameter has been analyzed when the others have been fixed.
Abstract: Heating is inevitable in any bearing operation. This
leads to not only the thinning of the lubricant but also could lead to a
thermal deformation of the bearing. The present work is an attempt to
analyze the influence of thermal deformation on the thermohydrodynamic
lubrication of infinitely long tilted pad slider rough
bearings. As a consequence of heating the slider is deformed and is
assumed to take a parabolic shape. Also the asperities expand leading
to smaller effective film thickness. Two different types of surface
roughness are considered: longitudinal roughness and transverse
roughness. Christensen-s stochastic approach is used to derive the
Reynolds-type equations. Density and viscosity are considered to be
temperature dependent. The modified Reynolds equation, momentum
equation, continuity equation and energy equation are decoupled and
solved using finite difference method to yield various bearing
characteristics. From the numerical simulations it is observed that the
performance of the bearing is significantly affected by the thermal
distortion of the slider and asperities and even the parallel sliders
seem to carry some load.
Abstract: In this paper, the differential quadrature method is applied to simulate natural convection in an inclined cubic cavity using velocity-vorticity formulation. The numerical capability of the present algorithm is demonstrated by application to natural convection in an inclined cubic cavity. The velocity Poisson equations, the vorticity transport equations and the energy equation are all solved as a coupled system of equations for the seven field variables consisting of three velocities, three vorticities and temperature. The coupled equations are simultaneously solved by imposing the vorticity definition at boundary without requiring the explicit specification of the vorticity boundary conditions. Test results obtained for an inclined cubic cavity with different angle of inclinations for Rayleigh number equal to 103, 104, 105 and 106 indicate that the present coupled solution algorithm could predict the benchmark results for temperature and flow fields. Thus, it is convinced that the present formulation is capable of solving coupled Navier-Stokes equations effectively and accurately.
Abstract: The stability of Newtonian and Non-Newtonian extending films under local or global heating or cooling conditions are considered. The thickness-averaged mass, momentum and energy equations with convective and radiative heat transfer are derived, both for Newtonian and non-Newtonian fluids (Maxwell, PTT and Giesekus models considered). The stability of the system is explored using either eigenvalue analysis or transient simulations. The results showed that the influence of heating and cooling on stability strongly depends on the magnitude of the Peclet number. Examples of stabilization or destabilization of heating or cooling are shown for Pe
Abstract: A numerical study on the heat transfer in the thermal
barrier coatings and the substrates of a parallel-plate enclosure is
carried out. Some of the thermal barrier coatings, such as ceramics, are
semitransparent and are of interest for high-temperature applications
where radiation effects are significant. The radiative transfer equations
and the energy equations are solved by using the discrete ordinates
method and the finite difference method. Illustrative results are
presented for temperature distributions in the coatings and the opaque
walls under various heating conditions. The results show that the
temperature distribution is more uniform in the interior portion of each
coating away from its boundary for the case with a larger average of
varying refractive index and a positive gradient of refractive index
enhances radiative transfer to the substrates.
Abstract: Simultaneous transient conduction and radiation heat
transfer with heat generation is investigated. Analysis is carried out
for both steady and unsteady situations. two-dimensional gray
cylindrical enclosure with an absorbing, emitting, and isotropically
scattering medium is considered. Enclosure boundaries are assumed
at specified temperatures. The heat generation rate is considered
uniform and constant throughout the medium. The lattice Boltzmann
method (LBM) was used to solve the energy equation of a transient
conduction-radiation heat transfer problem. The control volume finite
element method (CVFEM) was used to compute the radiative
information. To study the compatibility of the LBM for the energy
equation and the CVFEM for the radiative transfer equation, transient
conduction and radiation heat transfer problems in 2-D cylindrical
geometries were considered. In order to establish the suitability of the
LBM, the energy equation of the present problem was also solved
using the the finite difference method (FDM) of the computational
fluid dynamics. The CVFEM used in the radiative heat transfer was
employed to compute the radiative information required for the
solution of the energy equation using the LBM or the FDM (of the
CFD). To study the compatibility and suitability of the LBM for the
solution of energy equation and the CVFEM for the radiative
information, results were analyzed for the effects of various
parameters such as the boundary emissivity. The results of the LBMCVFEM
combination were found to be in excellent agreement with
the FDM-CVFEM combination. The number of iterations and the
steady state temperature in both of the combinations were found
comparable. Results are found for situations with and without heat
generation. Heat generation is found to have significant bearing on
temperature distribution.
Abstract: The effect of streamwise conduction on the thermal
characteristics of forced convection for nanofluidic flow in
rectangular microchannel heat sinks under isothermal wall has been
investigated. By applying the fin approach, models with and without
streamwise conduction term in the energy equation were developed
for hydrodynamically and thermally fully-developed flow. These two
models were solved to obtain closed form analytical solutions for the
nanofluid and solid wall temperature distributions and the analysis
emphasized details of the variations induced by the streamwise
conduction on the nanofluid heat transport characteristics. The effects
of the Peclet number, nanoparticle volume fraction, thermal
conductivity ratio on the thermal characteristics of forced convection
in microchannel heat sinks are analyzed. Due to the anomalous
increase in the effective thermal conductivity of nanofluid compared
to its base fluid, the effect of streamwise conduction is expected to be
more significant. This study reveals the significance of the effect of
streamwise conduction under certain conditions of which the
streamwise conduction should not be neglected in the forced
convective heat transfer analysis of microchannel heat sinks.
Abstract: This paper presents the buckling analysis of short and
long functionally graded cylindrical shells under thermal and
mechanical loads. The shell properties are assumed to vary
continuously from the inner surface to the outer surface of the shell.
The equilibrium and stability equations are derived using the total
potential energy equations, Euler equations and first order shear
deformation theory assumptions. The resulting equations are solved
for simply supported boundary conditions. The critical temperature
and pressure loads are calculated for both short and long cylindrical
shells. Comparison studies show the effects of functionally graded
index, loading type and shell geometry on critical buckling loads of
short and long functionally graded cylindrical shells.