Abstract: Multiport diffusers are the effective engineering
devices installed at the modern marine outfalls for the steady
discharge of effluent streams from the coastal plants, such as
municipal sewage treatment, thermal power generation and seawater
desalination. A mathematical model using a two-dimensional
advection-diffusion equation based on a flat seabed and incorporating
the effect of a coastal tidal current is developed to calculate the
compounded concentration following discharges of desalination
brine from a sea outfall with multiport diffusers. The analytical
solutions are computed graphically to illustrate the merging of
multiple brine plumes in shallow coastal waters, and further
approximation will be made to the maximum shoreline's
concentration to formulate dilution of a multiport diffuser discharge.
Abstract: The article deals with pneumatic and hot wire
anemometry measurement on subsonic axi-symmetric air ejector.
Performances of the ejector with and without pulsations of primary
flow are compared, measuring of characteristic pressures and mass
flow rates are performed and ejector efficiency is evaluated. The
pulsations of primary flow are produced by a synthetic jet generator,
which is placed in the supply line of the primary flow just in front of
the primary nozzle. The aim of the pulsation is to intensify the
mixing process. In the article we present: Pressure measuring of
pulsation on the mixing chamber wall, behind the mixing chamber
and behind the diffuser measured by fast pressure transducers and
results of hot wire anemometry measurement. It was found out that
using of primary flow pulsations yields higher back pressure behind
the ejector and higher efficiency. The processes in this ejector and
influences of primary flow pulsations on the mixing processes are
described.
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Abstract: This paper investigates experimental and numerical study of the airflow characteristics for vortex, round and square ceiling diffusers and its effect on the thermal comfort in a ventilated room. Three different thermal comfort criteria namely; Mean Age of the Air (MAA), ventilation effectiveness (E), and Effective Draft Temperature (EDT) have been used to predict the thermal comfort zone inside the room. In experimental work, a sub-scale room is set-up to measure the temperature field in the room. In numerical analysis, unstructured grids have been used to discretize the numerical domain. Conservation equations are solved using FLUENT commercial flow solver. The code is validated by comparing the numerical results obtained from three different turbulence models with the available experimental data. The comparison between the various numerical models shows that the standard k-ε turbulence model can be used to simulate these cases successfully. After validation of the code, effect of supply air velocity on the flow and thermal field could be investigated and hence the thermal comfort. The results show that the pressure coefficient created by the square diffuser is 1.5 times greater than that created by the vortex diffuser. The velocity decay coefficient is nearly the same for square and round diffusers and is 2.6 times greater than that for the vortex diffuser.
Abstract: The present paper develops and validates a numerical procedure for the calculation of turbulent combustive flow in converging and diverging ducts and throuh simulation of the heat transfer processes, the amount of production and spread of Nox pollutant has been measured. A marching integration solution procedure employing the TDMA is used to solve the discretized equations. The turbulence model is the Prandtl Mixing Length method. Modeling the combustion process is done by the use of Arrhenius and Eddy Dissipation method. Thermal mechanism has been utilized for modeling the process of forming the nitrogen oxides. Finite difference method and Genmix numerical code are used for numerical solution of equations. Our results indicate the important influence of the limiting diverging angle of diffuser on the coefficient of recovering of pressure. Moreover, due to the intense dependence of Nox pollutant to the maximum temperature in the domain with this feature, the Nox pollutant amount is also in maximum level.
Abstract: Plasma Wind Tunnels (PWT) are extensively used for screening and qualification of re-entry Thermel Protection System (TPS) materials. Proper design of a supersonic diffuser for plasma wind tunnel is of importance for achieving good pressurerecovery (thereby reducing vacuum pumping requirement & run time costs) and isolating downstream stream fluctuations from propagating costs) and isolating downstream stream fluctuationnts the details of a rapid design methodology successfully employed for designing supersonic diffuser for high power (several megawatts)plasma wind tunnels and numerical performance analysis of a diffuser configuration designed for one megawatt power rated plasma wind tunnel(enthalpy ~ 30 MJ/kg) using FLUENT 6.3® solver for different diffuser operating sub-atmospheric back-pressures.
Abstract: This paper reports on the results of experimental investigations on the performance of a jet pump operated under selected primary flows to optimize the related parameters. For this purpose a two-phase flow jet pump was used employing various profiles of nozzles as the primary device which was designed, fabricated and used along with the combination of mixing tube and diffuser. The profiles employed were circular, conical, and elliptical. The diameter of the nozzle used was 4 mm. The area ratio of the jet pump was 0.16. The test facility created for this purpose was an open loop continuous circulation system. Performance of the jet pump was obtained as iso-efficiency curves on characteristic curves drawn for various water flow rates. To perform the suction capability, evacuation test was conducted at best efficiency point for all the profiles.
Abstract: The flow field in a centrifugal fan is highly complex
with flow reversal taking place on the suction side of impeller and
diffuser vanes. Generally performance of the centrifugal fan could be
enhanced by judiciously introducing splitter vanes so as to improve
the diffusion process. An extensive numerical whole field analysis on
the effect of splitter vanes placed in discrete regions of suspected
separation points is possible using CFD. This paper examines the
effect of splitter vanes corresponding to various geometrical
locations on the impeller and diffuser. The analysis shows that the
splitter vanes located near the diffuser exit improves the static
pressure recovery across the diffusing domain to a larger extent. Also
it is found that splitter vanes located at the impeller trailing edge and
diffuser leading edge at the mid-span of the circumferential distance
between the blades show a marginal improvement in the static
pressure recovery across the fan. However, splitters provided near to
the suction side of the impeller trailing edge (25% of the
circumferential gap between the impeller blades towards the suction
side), adversely affect the static pressure recovery of the fan.