Abstract: Safety of bus journey is a fundamental concern. Risk of injuries and fatalities is severe when bus superstructure fails during rollover accident. Adequate design and sufficient strength of bus superstructure can reduce the number of injuries and fatalities. This paper deals with structural analysis of bus superstructure undergoes rollover event. Several value of mass will be varied in multiple simulations. The purpose of this work is to analyze structural response of bus superstructure in terms of deformation, stress and strain under several loading and constraining conditions. A complete bus superstructure with forty four passenger-s capability was developed using finite element analysis software. Simulations have been conducted to observe the effect of total mass of bus on the strength of superstructure. These simulations are following United Nation Economic Commission of Europe regulation 66 which focuses on strength of large vehicle superstructure. Validation process had been done using simple box model experiment and results obtained are comparing with simulation results. Inputs data from validation process had been used in full scale simulation. Analyses suggested that, the failure of bus superstructure during rollover situation is basically dependent on the total mass of bus and on the strength of bus superstructure.
Abstract: The main aim of the presented experiments is to
improve behaviour of sandwich structures under dynamic loading,
such as crash or explosion. Several cellular materials are widely used
as core of the sandwich structures and their properties influence
the response of the entire element under impact load. To optimize
their performance requires the characterisation of the core material
behaviour at high strain rates and identification of the underlying
mechanism. This work presents the study of high strain-rate
characteristics of a specific porous lightweight blast energy absorbing
foam using a Split Hopkinson Pressure Bar (SHPB) technique
adapted to perform tests on low strength materials. Two different
velocities, 15 and 30 m.s-1 were used to determine the strain
sensitivity of the material. Foams were designed using two types of
porous lightweight spherical raw materials with diameters of 30-
100 *m, combined with polymer matrix. Cylindrical specimens with
diameter of 15 mm and length of 7 mm were prepared and loaded
using a Split Hopkinson Pressure Bar apparatus to assess the relation
between the composition of the material and its shock wave
attenuation capacity.
Abstract: This paper describes the crashworthiness assessment and improvement of tlting train made of sandwich composites. The crashworhiness assessment of tilting train was conducted according to four collision scenarios of the Korean railway safety law. Collision analysis was carried out using explicit finite element analysis code LS-DYNA 3D. The finite element model consists of 3-D finite element model and 1-D equivalent model to save the finite element modeling and calculation time. It found that the crashworthiness analysis results were satisfied with the performance requirements except the crash scenario-2. In order to meet the crashworthiness requirements for crash scenario-2, the stiffness reinforcement for the laminate composite cover and metal frames of cabmask structure were proposed. Consequentially, it has satisfied the requirement for crash scenario-2.
Abstract: The aim of the study was to identify seat belt wearing
factor among road users in Malaysia. Evidence-based approach
through in-depth crash investigation was utilised to determine the
intended objectives. The objective was scoped into crashes
investigated by Malaysian Institute of Road Safety Research
(MIROS) involving passenger vehicles within 2007 and 2010. Crash
information of a total of 99 crash cases involving 240 vehicles and
864 occupants were obtained during the study period. Statistical test
and logistic regression analysis have been performed. Results of the
analysis revealed that gender, seat position and age were associated
with seat belt wearing compliance in Malaysia. Males are 97.6%
more likely to wear seat belt compared to females (95% CI 1.317 to
2.964). By seat position, the finding indicates that frontal occupants
were 82 times more likely to be wearing seat belt (95% CI 30.199 to
225.342) as compared to rear occupants. It is also important to note
that the odds of seat belt wearing increased by about 2.64% (95% CI
1.0176 to 1.0353) for every one year increase in age. This study is
essential in understanding the Malaysian tendency in belting up
while being occupied in a vehicle. The factors highlighted in this
study should be emphasized in road safety education in order to
increase seat belt wearing rate in this country and ultimately in
preventing deaths due to road crashes.
Abstract: In this study, optimization is carried out to find the optimized design of a foam-filled column for the best Specific Energy Absorption (SEA) and Crush Force Efficiency (CFE). In order to maximize SEA, the optimization gives the value of 2.3 for column thickness and 151.7 for foam length. On the other hand to maximize CFE, the optimization gives the value of 1.1 for column thickness and 200 for foam length. Finite Element simulation is run by using this value and the SEA and CFE obtained 1237.76 J/kg and 0.92.