Abstract: A specially designed flat plate was mounted vertically
over the axial line in the wind tunnel of the Aerospace Department of
the Pusan National University. The plate is 2 m long, 0.8 m high and 8
cm thick. The measurements were performed in velocity range from
15 to 60 m/s. A sand paper turbulizer was placed close to the plate nose
to provide fully developed turbulent boundary layer over the most part
of the plate. Strain balances were mounted in the trailing part of the
plate to measure the skin friction drag over removable insertions of
0.55×0.25m2 size. A set of the insertions was designed and
manufactured: 3mm thick polished metal surface and three compliant
surfaces. The compliant surfaces were manufactured of a silicone
rubber Silastic® S2 (Dow Corning company). To modify the
viscoelastic properties of the rubber, its composition was varied: 90%
of the rubber + 10% catalyst (standard), 92.5% + 7.5% (weak), 85% +
15% (strong). Modulus of elasticity and the loss tangent were
measured accurately for these materials in the frequency range from
40 Hz to 3 KHz using the unique proposed technique.
Abstract: This research investigates the effects of the opening
shape and location on the structural behavior of reinforced concrete
deep beam with openings, while keeping the opening size unchanged.
The software ANSYS 12.1 is used to handle the nonlinear finite
element analysis. The ultimate strength of reinforced concrete deep
beam with opening obtained by ANSYS 12.1 shows fair agreement
with the experimental results, with a difference of no more than 20%. The present work concludes that the opening location has much more effect on the structural strength than the opening shape. It was
concluded that placing the openings near the upper corners of the
deep beam may double the strength, and the use of a rectangular
narrow opening, with the long sides in the horizontal direction, can save up to 40% of structural strength of the deep beam.
Abstract: Images of human iris contain specular highlights due
to the reflective properties of the cornea. This corneal reflection
causes many errors not only in iris and pupil center estimation but
also to locate iris and pupil boundaries especially for methods that
use active contour. Each iris recognition system has four steps:
Segmentation, Normalization, Encoding and Matching. In order to
address the corneal reflection, a novel reflection removal method is
proposed in this paper. Comparative experiments of two existing
methods for reflection removal method are evaluated on CASIA iris
image databases V3. The experimental results reveal that the
proposed algorithm provides higher performance in reflection
removal.
Abstract: In this study, a longitudinal joint connection was
proposed for the short-span slab-type modular bridges with rapid
construction. The slab-type modular bridge consists of a number of
precast slab modules and has the joint connection between the
modules in the longitudinal direction of the bridge. A finite element
based parameter analysis was conducted to design the shape and the
dimensions of the longitudinal joint connection. Numbers of shear
keys within the joint, height and depth of the shear key, tooth angle,
and the spacing were considered as the design parameters. Using the
local cracking load at the corner of the shear key and the
cross-sectional area of the joint, an efficiency factor was proposed to
evaluate the effectiveness of the longitudinal joint connection. The
dimensions of shear key were determined by comparing the cracking
loads and the efficiency factors obtained from the finite element
analysis.
Abstract: Studies on Simultaneous Saccharification and Fermentation (SSF) of corn flour, a major agricultural product as the substrate using starch digesting glucoamylase enzyme derived from Aspergillus niger and non starch digesting and sugar fermenting Saccharomyces cerevisiae in a batch fermentation. Experiments based on Central Composite Design (CCD) were conducted to study the effect of substrate concentration, pH, temperature, enzyme concentration on Ethanol Concentration and the above parameters were optimized using Response Surface Methodology (RSM). The optimum values of substrate concentration, pH, temperature and enzyme concentration were found to be 160 g/l, 5.5, 30°C and 50 IU respectively. The effect of inoculums age on ethanol concentration was also investigated. The corn flour solution equivalent to 16% initial starch concentration gave the highest ethanol concentration of 63.04 g/l after 48 h of fermentation at optimum conditions of pH and temperature. Monod model and Logistic model were used for growth kinetics and Leudeking – Piret model was used for product formation kinetics.
Abstract: Waste corn pulp was investigated as a potential feedstock during vermicomposting using Eisenia fetida. Corn pulp is the major staple food in Southern Africa and constitutes about 25% of the total organic waste. Wastecooked corn pulp was blended with cow dung in the ratio 6:1 respectively to optimize the vermicomposting process. The feedstock was allowed to vermicompost for 30 days. The vermicomposting took place in a 3- tray plastic worm bin. Moisture content, temperature, pH, and electrical conductivity were monitoreddaily. The NPK content was determined at day 30. During vermicomposting, moisture content increased from 27.68% to 52.41%, temperature ranged between 19- 25◦C, pH increased from 5.5 to 7.7, and electrical conductivity decreased from 80000μS/cm to 60000μS/cm. The ash content increased from 11.40% to 28.15%; additionally the volatile matter increased from 1.45% to 10.02%. An odorless, dark brown vermicompost was obtained. The vermicompost NPK content was 4.19%, 1.15%, and 6.18% respectively.
Abstract: Deformable active contours are widely used in
computer vision and image processing applications for image
segmentation, especially in biomedical image analysis. The active
contour or “snake" deforms towards a target object by controlling the
internal, image and constraint forces. However, if the contour
initialized with a lesser number of control points, there is a high
probability of surpassing the sharp corners of the object during
deformation of the contour. In this paper, a new technique is
proposed to construct the initial contour by incorporating prior
knowledge of significant corners of the object detected using the
Harris operator. This new reconstructed contour begins to deform, by
attracting the snake towards the targeted object, without missing the
corners. Experimental results with several synthetic images show the
ability of the new technique to deal with sharp corners with a high
accuracy than traditional methods.