Abstract: This paper presents the results of an experimental
investigation carried out to evaluate the shrinkage of High Strength
Concrete. High Strength Concrete is made by partially replacement of
cement by flyash and silica fume. The shrinkage of High Strength
Concrete has been studied using the different types of coarse and fine
aggregates i.e. Sandstone and Granite of 12.5 mm size and Yamuna
and Badarpur Sand. The Mix proportion of concrete is 1:0.8:2.2 with
water cement ratio as 0.30. Superplasticizer dose @ of 2% by weight
of cement is added to achieve the required degree of workability in
terms of compaction factor.
From the test results of the above investigation it can be concluded
that the shrinkage strain of High Strength Concrete increases with
age. The shrinkage strain of concrete with replacement of cement by
10% of Flyash and Silica fume respectively at various ages are more
(6 to 10%) than the shrinkage strain of concrete without Flyash and
Silica fume. The shrinkage strain of concrete with Badarpur sand as
Fine aggregate at 90 days is slightly less (10%) than that of concrete
with Yamuna Sand. Further, the shrinkage strain of concrete with
Granite as Coarse aggregate at 90 days is slightly less (6 to 7%) than
that of concrete with Sand stone as aggregate of same size. The
shrinkage strain of High Strength Concrete is also compared with that
of normal strength concrete. Test results show that the shrinkage
strain of high strength concrete is less than that of normal strength
concrete.
Abstract: Fuzzy logic can be used when knowledge is
incomplete or when ambiguity of data exists. The purpose of
this paper is to propose a proactive fuzzy set- based model for
reacting to the risk inherent in investment activities relative to
a complete view of portfolio management. Fuzzy rules are
given where, depending on the antecedents, the portfolio size
may be slightly or significantly decreased or increased. The
decision maker considers acceptable bounds on the proportion
of acceptable risk and return. The Fuzzy Controller model
allows learning to be achieved as 1) the firing strength of each
rule is measured, 2) fuzzy output allows rules to be updated,
and 3) new actions are recommended as the system continues
to loop. An extension is given to the fuzzy controller that
evaluates potential financial loss before adjusting the
portfolio. An application is presented that illustrates the
algorithm and extension developed in the paper.
Abstract: For the electrical metrics that describe photovoltaic
cell performance are inherently multivariate in nature, use of a
univariate, or one variable, statistical process control chart can have
important limitations. Development of a comprehensive process
control strategy is known to be significantly beneficial to reducing
process variability that ultimately drives up the manufacturing cost
photovoltaic cells. The multivariate moving average or MMA chart,
is applied to the electrical metrics of photovoltaic cells to illustrate
the improved sensitivity on process variability this method of control
charting offers. The result show the ability of the MMA chart to
expand to as any variables as needed, suggests an application
with multiple photovoltaic electrical metrics being used in
concert to determine the processes state of control.
Abstract: We describe a novel method for removing noise (in wavelet domain) of unknown variance from microarrays. The method is based on a smoothing of the coefficients of the highest subbands. Specifically, we decompose the noisy microarray into wavelet subbands, apply smoothing within each highest subband, and reconstruct a microarray from the modified wavelet coefficients. This process is applied a single time, and exclusively to the first level of decomposition, i.e., in most of the cases, it is not necessary a multirresoltuion analysis. Denoising results compare favorably to the most of methods in use at the moment.
Abstract: This paper describes technological possibilities to
enhance methane productionin the anaerobic stabilization of wastewater treatment plant excess sludge. This objective can be achieved by the addition of waste residues: crude glycerol from biodiesel production and residues from fishery. The addition
ofglycerol in an amount by weight of 2 – 5% causes enhancement of methane production of about 250 – 400%. At the same time the
percentage increase of total solids concentration in the outgoing sludge is ten or more times less. The containment of methane in
biogas is higher in case of admixed substrate.
Abstract: We consider a typical problem in the assembly of
printed circuit boards (PCBs) in a two-machine flow shop system to
simultaneously minimize the weighted sum of weighted tardiness and
weighted flow time. The investigated problem is a group scheduling
problem in which PCBs are assembled in groups and the interest is to
find the best sequence of groups as well as the boards within each
group to minimize the objective function value. The type of setup
operation between any two board groups is characterized as carryover
sequence-dependent setup time, which exactly matches with the real
application of this problem. As a technical constraint, all of the
boards must be kitted before the assembly operation starts (kitting
operation) and by kitting staff. The main idea developed in this paper
is to completely eliminate the role of kitting staff by assigning the
task of kitting to the machine operator during the time he is idle
which is referred to as integration of internal (machine) and external
(kitting) setup times. Performing the kitting operation, which is a
preparation process of the next set of boards while the other boards
are currently being assembled, results in the boards to continuously
enter the system or have dynamic arrival times. Consequently, a
dynamic PCB assembly system is introduced for the first time in the
assembly of PCBs, which also has characteristics similar to that of
just-in-time manufacturing. The problem investigated is
computationally very complex, meaning that finding the optimal
solutions especially when the problem size gets larger is impossible.
Thus, a heuristic based on Genetic Algorithm (GA) is employed. An
example problem on the application of the GA developed is
demonstrated and also numerical results of applying the GA on
solving several instances are provided.
Abstract: The main aim of this study is to identify the most
influential variables that cause defects on the items produced by a
casting company located in Turkey. To this end, one of the items
produced by the company with high defective percentage rates is
selected. Two approaches-the regression analysis and decision treesare
used to model the relationship between process parameters and
defect types. Although logistic regression models failed, decision tree
model gives meaningful results. Based on these results, it can be
claimed that the decision tree approach is a promising technique for
determining the most important process variables.
Abstract: Many corporations are seriously concerned about
security of networks and therefore, their network supervisors are still
reluctant to install WLANs. In this regards, the IEEE802.11i standard
was developed to address the security problems, even though the
mistrust of the wireless LAN technology is still existing. The thought
was that the best security solutions could be found in open standards
based technologies that can be delivered by Virtual Private
Networking (VPN) being used for long time without addressing any
security holes for the past few years. This work, addresses this issue
and presents a simulated wireless LAN of IEEE802.11g protocol, and
analyzes impact of integrating Virtual Private Network technology to
secure the flow of traffic between the client and the server within the
LAN, using OPNET WLAN utility. Two Wireless LAN scenarios
have been introduced and simulated. These are based on normal
extension to a wired network and VPN over extension to a wired
network. The results of the two scenarios are compared and indicate
the impact of improving performance, measured by response time
and load, of Virtual Private Network over wireless LAN.
Abstract: Software maintenance and mainly software
comprehension pose the largest costs in the software lifecycle. In
order to assess the cost of software comprehension, various
complexity measures have been proposed in the literature. This paper
proposes new cognitive-spatial complexity measures, which combine
the impact of spatial as well as architectural aspect of the software to
compute the software complexity. The spatial aspect of the software
complexity is taken into account using the lexical distances (in
number of lines of code) between different program elements and the
architectural aspect of the software complexity is taken into
consideration using the cognitive weights of control structures
present in control flow of the program. The proposed measures are
evaluated using standard axiomatic frameworks and then, the
proposed measures are compared with the corresponding existing
cognitive complexity measures as well as the spatial complexity
measures for object-oriented software. This study establishes that the
proposed measures are better indicators of the cognitive effort
required for software comprehension than the other existing
complexity measures for object-oriented software.
Abstract: These days wireless local area networks has become
very popular, when the initial IEEE802.11 is the standard for
providing wireless connectivity to automatic machinery, equipment
and stations that require rapid deployment, which may be portable,
handheld or which may be mounted on moving vehicles within a
local area. IEEE802.11 Wireless local area network is a sharedmedium
communication network that transmits information over
wireless links for all IEEE802.11 stations in its transmission range to
receive. When a user is moving from one location to another, how
the other user knows about the required station inside WLAN. For
that we designed and implemented a system to locate a mobile user
inside the wireless local area network based on RSSI with the help of
four specially designed architectures. These architectures are based
on statistical or we can say manual configuration of mapping and
radio map of indoor and outdoor location with the help of available
Sniffer based and cluster based techniques. We found a better
location of a mobile user in WLAN. We tested this work in indoor
and outdoor environments with different locations with the help of
Pamvotis, a simulator for WLAN.
Abstract: This paper aims to select the optimal location and
setting parameters of TCSC (Thyristor Controlled Series
Compensator) controller using Particle Swarm Optimization (PSO)
and Genetic Algorithm (GA) to mitigate small signal oscillations in a
multimachine power system. Though Power System Stabilizers
(PSSs) are prime choice in this issue, installation of FACTS device
has been suggested here in order to achieve appreciable damping of
system oscillations. However, performance of any FACTS devices
highly depends upon its parameters and suitable location in the
power network. In this paper PSO as well as GA based techniques are
used separately and compared their performances to investigate this
problem. The results of small signal stability analysis have been
represented employing eigenvalue as well as time domain response in
face of two common power system disturbances e.g., varying load
and transmission line outage. It has been revealed that the PSO based
TCSC controller is more effective than GA based controller even
during critical loading condition.
Abstract: This paper presents a model for the characterization
and selection of beeswaxes for use as base substitute tissue for the
manufacture of objects suitable for external radiotherapy using
megavoltage photon beams. The model of characterization was
divided into three distinct stages: 1) verification of aspects related to
the origin of the beeswax, the bee species, the flora in the vicinity of
the beehives and procedures to detect adulterations; 2) evaluation of
physical and chemical properties; and 3) evaluation of beam
attenuation capacity. The chemical composition of the beeswax
evaluated in this study was similar to other simulators commonly
used in radiotherapy. The behavior of the mass attenuation coefficient
in the radiotherapy energy range was comparable to other simulators.
The proposed model is efficient and enables convenient assessment
of the use of any particular beeswax as a base substitute tissue for
radiotherapy.
Abstract: At the previous study of new metal gasket, contact
width and contact stress were important design parameter for
optimizing metal gasket performance. However, the range of contact
stress had not been investigated thoroughly. In this study, we
conducted a gasket design optimization based on an elastic and plastic
contact stress analysis considering forming effect using FEM. The
gasket model was simulated by using two simulation stages which is
forming and tightening simulation. The optimum design based on an
elastic and plastic contact stress was founded. Final evaluation was
determined by helium leak quantity to check leakage performance of
both type of gaskets. The helium leak test shows that a gasket based
on the plastic contact stress design better than based on elastic stress
design.
Abstract: A generalization of the concepts of Feistel Networks (FN), known as Extended Feistel Network (EFN) is examined. EFN splits the input blocks into n > 2 sub-blocks. Like conventional FN, EFN consists of a series of rounds whereby at least one sub-block is subjected to an F function. The function plays a key role in the diffusion process due to its completeness property. It is also important to note that in EFN the F-function is the most computationally expensive operation in a round. The aim of this paper is to determine a suitable type of EFN for a scalable cipher. This is done by analyzing the threshold number of rounds for different types of EFN to achieve the completeness property as well as the number of F-function required in the network. The work focuses on EFN-Type I, Type II and Type III only. In the analysis it is found that EFN-Type II and Type III diffuses at the same rate and both are faster than Type-I EFN. Since EFN-Type-II uses less F functions as compared to EFN-Type III, therefore Type II is the most suitable EFN for use in a scalable cipher.
Abstract: In this research, an anaerobic co-digestion using decanter cake from palm oil mill industry to improve the biogas production from frozen seafood wastewater is studied using Continuously Stirred Tank Reactor (CSTR) process. The experiments were conducted in laboratory-scale. The suitable Hydraulic Retention Time (HRT) was observed in CSTR experiments with 24 hours of mixing time using the mechanical mixer. The HRT of CSTR process impacts on the efficiency of biogas production. The best performance for biogas production using CSTR process was the anaerobic codigestion for 20 days of HRT with the maximum methane production rate of 1.86 l/d and the average maximum methane production of 64.6%. The result can be concluded that the decanter cake can improve biogas productivity of frozen seafood wastewater.
Abstract: Employing a recently introduced unified adaptive filter
theory, we show how the performance of a large number of important
adaptive filter algorithms can be predicted within a general framework
in nonstationary environment. This approach is based on energy conservation
arguments and does not need to assume a Gaussian or white
distribution for the regressors. This general performance analysis can
be used to evaluate the mean square performance of the Least Mean
Square (LMS) algorithm, its normalized version (NLMS), the family
of Affine Projection Algorithms (APA), the Recursive Least Squares
(RLS), the Data-Reusing LMS (DR-LMS), its normalized version
(NDR-LMS), the Block Least Mean Squares (BLMS), the Block
Normalized LMS (BNLMS), the Transform Domain Adaptive Filters
(TDAF) and the Subband Adaptive Filters (SAF) in nonstationary
environment. Also, we establish the general expressions for the
steady-state excess mean square in this environment for all these
adaptive algorithms. Finally, we demonstrate through simulations that
these results are useful in predicting the adaptive filter performance.
Abstract: This article provides partial evaluation index and its
standard of sports aerobics, including the following 12 indexes: health
vitality, coordination, flexibility, accuracy, pace, endurance, elasticity,
self-confidence, form, control, uniformity and musicality. The
three-layer BP artificial neural network model including input layer,
hidden layer and output layer is established. The result shows that the
model can well reflect the non-linear relationship between the
performance of 12 indexes and the overall performance. The predicted
value of each sample is very close to the true value, with a relative
error fluctuating around of 5%, and the network training is successful.
It shows that BP network has high prediction accuracy and good
generalization capacity if being applied in sports aerobics performance
evaluation after effective training.
Abstract: In this paper, we implement a modern serial backplane
platform for telecommunication inter-rack systems. For combination
high reliability and low cost protocol property, we applied high level
data link control (HDLC) protocol with low voltage differential
signaling (LVDS) bus for card to card communicated over backplane.
HDLC protocol is a high performance with several operation modes
and is famous in telecommunication systems. LVDS bus is a high
reliability with high immunity against electromagnetic interference
(EMI) and noise.
Abstract: A mobile Ad-hoc network consists of wireless nodes
communicating without the need for a centralized administration. A
user can move anytime in an ad hoc scenario and, as a result, such a
network needs to have routing protocols which can adopt
dynamically changing topology. To accomplish this, a number of ad
hoc routing protocols have been proposed and implemented, which
include DSR, OLSR and AODV. This paper presents a study on the
QoS parameters for MANET application traffics in large-scale
scenarios with 50 and 120 nodes. The application traffics analyzed in
this study is File Transfer Protocol (FTP). In large scale networks
(120 nodes) OLSR shows better performance and in smaller scale
networks (50 nodes)AODV shows less packet drop rate and OLSR
shows better throughput.
Abstract: Integrated fiber-wireless (FiWi) access networks are a viable solution that can deliver the high profile quadruple play services. Passive optical networks (PON) networks integrated with wireless access networks provide ubiquitous characteristics for high bandwidth applications. Operation of PON improves by employing a variety of multiplexing techniques. One of it is time division/wavelength division multiplexed (TDM/WDM) architecture that improves the performance of optical-wireless access networks. This paper proposes a novel feedback-based TDM/WDM-PON architecture and introduces a model of integrated PON-FiWi networks. Feedback-based link architecture is an efficient solution to improves the performance of optical-line-terminal (OLT) and interlink optical-network-units (ONUs) communication. Furthermore, the feedback-based WDM/TDM-PON architecture is compared with existing architectures in terms of capacity of network throughput.