Abstract: Car failure detection is a complicated process and
requires high level of expertise. Any attempt of developing an expert
system dealing with car failure detection has to overcome various
difficulties. This paper describes a proposed knowledge-based
system for car failure detection. The paper explains the need for an
expert system and the some issues on developing knowledge-based
systems, the car failure detection process and the difficulties involved
in developing the system. The system structure and its components
and their functions are described. The system has about 150 rules for
different types of failures and causes. It can detect over 100 types of
failures. The system has been tested and gave promising results.
Abstract: The paper presents the modeling of nonlinear
longitudinal aerodynamics using flight data of Hansa-3 aircraft at
high angles of attack near stall. The Kirchhoff-s quasi-steady stall
model has been used to incorporate nonlinear aerodynamic effects in
the aerodynamic model used to estimate the parameters, thereby,
making the aerodynamic model nonlinear. The Maximum Likelihood
method has been applied to the flight data (at high angles of attack)
for the estimation of parameters (aerodynamic and stall
characteristics) using the nonlinear aerodynamic model. To improve
the accuracy level of the estimates, an approach of fixing the strong
parameters has also been presented.
Abstract: The paper considered the construction of BIBDs using potential Lotto Designs (LDs) earlier derived from qualifying parent BIBDs. The study utilized Li’s condition pr t−1 ( t−1 2 ) + pr− pr t−1 (t−1) 2 < ( p 2 ) λ, to determine the qualification of a parent BIBD (v, b, r, k, λ) as LD (n, k, p, t) constrained on v ≥ k, v ≥ p, t ≤ min{k, p} and then considered the case k = t since t is the smallest number of tickets that can guarantee a win in a lottery. The (15, 140, 28, 3, 4) and (7, 7, 3, 3, 1) BIBDs were selected as parent BIBDs to illustrate the procedure. These BIBDs yielded three potential LDs each. Each of the LDs was completely generated and their properties studied. The three LDs from the (15, 140, 28, 3, 4) produced (9, 84, 28, 3, 7), (10, 120, 36, 3, 8) and (11, 165, 45, 3, 9) BIBDs while those from the (7, 7, 3, 3, 1) produced the (5, 10, 6, 3, 3), (6, 20, 10, 3, 4) and (7, 35, 15, 3, 5) BIBDs. The produced BIBDs follow the generalization (v + 1, b + r + λ + 1, r +λ+1, k, λ+1) where (v, b, r, k, λ) are the parameters of the (9, 84, 28, 3, 7) and (5, 10, 6, 3, 3) BIBDs. All the BIBDs produced are unreduced designs.
Abstract: This paper presents an algorithm for the recognition
and tracking of moving objects, 1/10 scale model car is used to verify
performance of the algorithm. Presented algorithm for the recognition
and tracking of moving objects in the paper is as follows. SURF
algorithm is merged with Lucas-Kanade algorithm. SURF algorithm
has strong performance on contrast, size, rotation changes and it
recognizes objects but it is slow due to many computational
complexities. Processing speed of Lucas-Kanade algorithm is fast but
the recognition of objects is impossible. Its optical flow compares the
previous and current frames so that can track the movement of a pixel.
The fusion algorithm is created in order to solve problems which
occurred using the Kalman Filter to estimate the position and the
accumulated error compensation algorithm was implemented. Kalman
filter is used to create presented algorithm to complement problems
that is occurred when fusion two algorithms. Kalman filter is used to
estimate next location, compensate for the accumulated error. The
resolution of the camera (Vision Sensor) is fixed to be 640x480. To
verify the performance of the fusion algorithm, test is compared to
SURF algorithm under three situations, driving straight, curve, and
recognizing cars behind the obstacles. Situation similar to the actual is
possible using a model vehicle. Proposed fusion algorithm showed
superior performance and accuracy than the existing object
recognition and tracking algorithms. We will improve the performance
of the algorithm, so that you can experiment with the images of the
actual road environment.
Abstract: The position and momentum space information entropies
of hydrogen atom are exactly evaluated. Using isospectral
Hamiltonian approach, a family of isospectral potentials is constructed having same energy eigenvalues as that of the original potential. The information entropy content is obtained in position
space as well as in momentum space. It is shown that the information
entropy content in each level can be re-arranged as a function of deformation parameter.
Abstract: The hand is one of the essential parts of the body for
carrying out Activities of Daily Living (ADLs). Individuals use their
hands and fingers in everyday activities in the both the workplace
and home. Hand-intensive tasks require diverse and sometimes
extreme levels of exertion, depending on the action, movement or
manipulation involved. The authors have undertaken several studies
looking at grip choice and comfort. It is hoped that in providing
improved understanding of discomfort during ADLs this will aid in
the design of consumer products.
Previous work by the authors outlined a methodology for
calculating pain frequency and pain level for a range of tasks. From
an online survey undertaken by the authors with regards
manipulating objects during everyday tasks, tasks involving
gripping were seen to produce the highest levels of pain and
discomfort. Questioning of the participants showed that cleaning
tasks were seen to be ADL's that produced the highest levels of
discomfort, with women feeling higher levels of discomfort than
men.
This paper looks at the methodology for calculating pain
frequency and pain level with particular regards to gripping
activities. This methodology shows that activities such as mopping,
sweeping and hoovering shows the highest numbers of pain
frequency and pain level at 3112.5 frequency per month while the
pain level per person doing this action was 0.78.The study then uses
thin-film force sensors to analyze the force distribution in the hand
whilst hoovering and compares this for differing grip styles and
genders. Women were seen to have more of their hand under a
higher pressure than men when undertaking hoovering. This
suggests that women may feel greater discomfort than men since
their hand is at a higher pressure more of the time.
Abstract: The Muslim faith requires individuals to fast between
the hours of sunrise and sunset during the month of Ramadan. Our
recent work has concentrated on some of the changes that take place
during the daytime when fasting. A questionnaire was developed to
assess subjective estimates of physical, mental and social activities,
and fatigue. Four days were studied: in the weeks before and after
Ramadan (control days) and during the first and last weeks of
Ramadan (experimental days). On each of these four days, this
questionnaire was given several times during the daytime and once
after the fast had been broken and just before individuals retired at
night.
During Ramadan, daytime mental, physical and social activities
all decreased below control values but then increased to abovecontrol
values in the evening. The desires to perform physical and
mental activities showed very similar patterns. That is, individuals
tried to conserve energy during the daytime in preparation for the
evenings when they ate and drank, often with friends. During
Ramadan also, individuals were more fatigued in the daytime and
napped more often than on control days. This extra fatigue probably
reflected decreased sleep, individuals often having risen earlier
(before sunrise, to prepare for fasting) and retired later (to enable
recovery from the fast).
Some physiological measures and objective measures of
performance (including the response to a bout of exercise) have also
been investigated. Urine osmolality fell during the daytime on
control days as subjects drank, but rose in Ramadan to reach values
at sunset indicative of dehydration. Exercise performance was also
compromised, particularly late in the afternoon when the fast had
lasted several hours. Self-chosen exercise work-rates fell and a set
amount of exercise felt more arduous. There were also changes in
heart rate and lactate accumulation in the blood, indicative of greater
cardiovascular and metabolic stress caused by the exercise in
subjects who had been fasting. Daytime fasting in Ramadan produces
widespread effects which probably reflect combined effects of sleep
loss and restrictions to intakes of water and food.
Abstract: Subsurface erosion in river banks and its details, in
spite of its occurrence in various parts of the world has rarely been
paid attention by researchers. In this paper, quantitative concept of
the subsurface bank erosion has been investigated for vertical banks.
Vertical banks were simulated experimentally by considering a sandy
erodible layer overlaid by clayey one under uniformly distributed
constant overhead pressure. Results of the experiments are indicated
that rate of sandy layer erosion is decreased by an increase in
overburden; likewise, substituting 20% of coarse (3.5 mm) sand layer
bed material by fine material (1.4 mm) may lead to a decrease in
erosion rate by one-third. This signifies the importance of the bed
material composition effect on sandy layers erosion due to subsurface
erosion in river banks.
Abstract: Some meta-schedulers query the information system of individual supercomputers in order to submit jobs to the least busy supercomputer on a computational Grid. However, this information can become outdated by the time a job starts due to changes in scheduling priorities. The MSR scheme is based on Multiple Simultaneous Requests and can take advantage of opportunities resulting from these priorities changes. This paper presents the SWARM meta-scheduler, which can speed up the execution of large sets of tasks by minimizing the job queuing time through the submission of multiple requests. Performance tests have shown that this new meta-scheduler is faster than an implementation of the MSR scheme and the gLite meta-scheduler. SWARM has been used through the GridQTL project beta-testing portal during the past year. Statistics are provided for this usage and demonstrate its capacity to achieve reliably a substantial reduction of the execution time in production conditions.
Abstract: Reciprocating compressors are flexible to handle wide capacity and condition swings, offer a very efficient method of compressing almost any gas mixture in wide range of pressure, can generate high head independent of density, and have numerous applications and wide power ratings. These make them vital component in various units of industrial plants. In this paper optimum reciprocating compressor configuration regarding interstage pressures, low suction pressure, non-lubricated cylinder, speed of machine, capacity control system, compressor valve, lubrication system, piston rod coating, cylinder liner material, barring device, pressure drops, rod load, pin reversal, discharge temperature, cylinder coolant system, performance, flow, coupling, special tools, condition monitoring (including vibration, thermal and rod drop monitoring), commercial points, delivery and acoustic conditions are presented.
Abstract: This study aims to propose three evaluation methods to
evaluate the Tokyo Cap and Trade Program when emissions trading is
performed virtually among enterprises, focusing on carbon dioxide
(CO2), which is the only emitted greenhouse gas that tends to increase.
The first method clarifies the optimum reduction rate for the highest
cost benefit, the second discusses emissions trading among enterprises
through market trading, and the third verifies long-term emissions
trading during the term of the plan (2010-2019), checking the validity
of emissions trading partly using Geographic Information Systems
(GIS). The findings of this study can be summarized in the following
three points.
1. Since the total cost benefit is the greatest at a 44% reduction rate, it
is possible to set it more highly than that of the Tokyo Cap and
Trade Program to get more total cost benefit.
2. At a 44% reduction rate, among 320 enterprises, 8 purchasing
enterprises and 245 sales enterprises gain profits from emissions
trading, and 67 enterprises perform voluntary reduction without
conducting emissions trading. Therefore, to further promote
emissions trading, it is necessary to increase the sales volumes of
emissions trading in addition to sales enterprises by increasing the
number of purchasing enterprises.
3. Compared to short-term emissions trading, there are few enterprises
which benefit in each year through the long-term emissions trading
of the Tokyo Cap and Trade Program. Only 81 enterprises at the
most can gain profits from emissions trading in FY 2019. Therefore,
by setting the reduction rate more highly, it is necessary to increase
the number of enterprises that participate in emissions trading and
benefit from the restraint of CO2 emissions.
Abstract: The Shanghai Cooperation Organization is one of the successful outcomes of China's foreign policy since the end of the Cold war. The expansion of multilateral ties all over the world by dint of pursuing institutional strategies as SCO, identify China as a more constructive power. SCO became a new model of cooperation that was formed on remains of collapsed Soviet system, and predetermined China's geopolitical role in the region. As the fast developing effective regional mechanism, SCO today has more of external impact on the international system and forms a new type of interaction for promoting China's grand strategy of 'peaceful rise'.
Abstract: This paper describes a system-level SoC energy
consumption estimation method based on a dynamic behavior of
embedded software in the early stages of the SoC development. A
major problem of SOC development is development rework caused by
unreliable energy consumption estimation at the early stages. The
energy consumption of an SoC used in embedded systems is strongly
affected by the dynamic behavior of the software. At the early stages
of SoC development, modeling with a high level of abstraction is
required for both the dynamic behavior of the software, and the
behavior of the SoC. We estimate the energy consumption by a UML
model-based simulation. The proposed method is applied for an actual
embedded system in an MFP. The energy consumption estimation of
the SoC is more accurate than conventional methods and this proposed
method is promising to reduce the chance of development rework in
the SoC development. ∈
Abstract: Information on weed distribution within the field is necessary to implement spatially variable herbicide application. Since hand labor is costly, an automated weed control system could be feasible. This paper deals with the development of an algorithm for real time specific weed recognition system based on Histogram Maxima with threshold of an image that is used for the weed classification. This algorithm is specifically developed to classify images into broad and narrow class for real-time selective herbicide application. The developed system has been tested on weeds in the lab, which have shown that the system to be very effectiveness in weed identification. Further the results show a very reliable performance on images of weeds taken under varying field conditions. The analysis of the results shows over 95 percent classification accuracy over 140 sample images (broad and narrow) with 70 samples from each category of weeds.
Abstract: Since the world printing industry has to confront
globalization with a constant change, the Thai printing industry, as a
small but increasingly significant part of the world printing industry,
cannot inevitably escape but has to encounter with the similar change
and also the need to revamp its production processes, designs and
technology to make them more appealing to both international and
domestic market. The essential question is what is the Thai
competitive edge in the printing industry in changing environment?
This research is aimed to study the Thai level of competitive edge in
terms of marketing, technology, environment friendly, and the level
of satisfaction of the process of using printing machines. To access
the extent to which is the trends in competitiveness of Thai printing
industry, both quantitative and qualitative study were conducted. The
quantitative analysis was restricted to 100 respondents. The
qualitative analysis was restricted to a focus group of 10 individuals
from various backgrounds in the Thai printing industry. The findings
from the quantitative analysis revealed that the overall mean scores
are 4.53, 4.10, and 3.50 for the competitiveness of marketing, the
competitiveness of technology, and the competitiveness of being
environment friendly respectively. However, the level of satisfaction
for the process of using machines has a mean score only 3.20. The
findings from the qualitative analysis have revealed that target
customers have increasingly reordered due to their contentment in
both low prices and the acceptable quality of the products. Moreover,
the Thai printing industry has a tendency to convert to ambient green
technology which is friendly to the environment. The Thai printing
industry is choosing to produce or substitute with products that are
less damaging to the environment. It is also found that the Thai
printing industry has been transformed into a very competitive
industry which bargaining power rests on consumers who have a
variety of choices.
Abstract: Performance of millimeter-wave (mm-wave) multiband
orthogonal frequency division multiplexing (MB-OFDM) ultrawideband
(UWB) signal generation using frequency quadrupling
technique and transmission over fiber is experimentally investigated.
The frequency quadrupling is achived by using only one Mach-
Zehnder modulator (MZM) that is biased at maximum transmission
(MATB) point. At the output, a frequency quadrupling signal is
obtained then sent to a second MZM. This MZM is used for MBOFDM
UWB signal modulation. In this work, we demonstrate 30-
GHz mm-wave wireless that carries three-bands OFDM UWB
signals, and error vector magnitude (EVM) is used to analyze the
transmission quality. It is found that our proposed technique leads to
an improvement of 3.5 dB in EVM at 40% of local oscillator (LO)
modulation with comparison to the technique using two cascaded
MZMs biased at minimum transmission (MITB) point.
Abstract: The aim of this study is to determine the effect of
strategic management implementations on the institutionalization
levels. In this regard a field study has been made over 31 stone quarry
enterprises in cement producing sector in Konya by using survey
method. In this study, institutionalization levels of the enterprises
have been evaluated regarding three dimensions: professionalization,
management approach, participation in decisions and delegation of
authority. According to the results of the survey, there is a highly
positive and statistically significant relationship between the strategic
management implementations and institutionalization levels of the
enterprises. Additionally,-considering the results of regression
analysis made for establishing the relationship between strategic
management and institutionalization levels- it has been determined
that strategic management implementations of the enterprises can be
used as a variable to explain the institutionalization levels of them,
and also strategic management implementations of the enterprises
increase the institutionalization levels of them.
Abstract: In the classical buckling analysis of rectangular plates
subjected to the concurrent action of shear and uniaxial forces, the
Euler shear buckling stress is generally evaluated separately, so that
no influence on the shear buckling coefficient, due to the in-plane
tensile or compressive forces, is taken into account.
In this paper the buckling problem of simply supported rectangular
plates, under the combined action of shear and uniaxial forces, is
discussed from the beginning, in order to obtain new project formulas
for the shear buckling coefficient that take into account the presence
of uniaxial forces.
Furthermore, as the classical expression of the shear buckling
coefficient for simply supported rectangular plates is considered only
a “rough" approximation, as the exact one is defined by a system of
intersecting curves, the convergence and the goodness of the classical
solution are analyzed, too.
Finally, as the problem of the Euler shear buckling stress
evaluation is a very important topic for a variety of structures, (e.g.
ship ones), two numerical applications are carried out, in order to
highlight the role of the uniaxial stresses on the plating scantling
procedures and the goodness of the proposed formulas.
Abstract: Many agent-oriented software engineering
methodologies have been proposed for software developing; however
their application is still limited due to their lack of maturity.
Evaluating the strengths and weaknesses of these methodologies
plays an important role in improving them and in developing new
stronger methodologies. This paper presents an evaluation framework
for agent-oriented methodologies, which addresses six major areas:
concepts, notation, process, pragmatics, support for software
engineering and marketability. The framework is then used to
evaluate the Gaia methodology to identify its strengths and
weaknesses, and to prove the ability of the framework for promoting
the agent-oriented methodologies by detecting their weaknesses in
detail.
Abstract: This research is a comparative study of complexity, as a multidimensional concept, in the context of streetscape composition in Algeria and Japan. 80 streetscapes visual arrays have been collected and then presented to 20 participants, with different cultural backgrounds, in order to be categorized and classified according to their degrees of complexity. Three analysis methods have been used in this research: cluster analysis, ranking method and Hayashi Quantification method (Method III). The results showed that complexity, disorder, irregularity and disorganization are often conflicting concepts in the urban context. Algerian daytime streetscapes seem to be balanced, ordered and regular, and Japanese daytime streetscapes seem to be unbalanced, regular and vivid. Variety, richness and irregularity with some aspects of order and organization seem to characterize Algerian night streetscapes. Japanese night streetscapes seem to be more related to balance, regularity, order and organization with some aspects of confusion and ambiguity. Complexity characterized mainly Algerian avenues with green infrastructure. Therefore, for Japanese participants, Japanese traditional night streetscapes were complex. And for foreigners, Algerian and Japanese avenues nightscapes were the most complex visual arrays.