Abstract: This paper presents a method for the efficient
implementation of a unidirectional or bidirectional DC/DC converter.
The DC/DC converter is used essentially for energy exchange
between the low voltage service battery and a high voltage battery
commonly found in Electric Vehicle applications. In these
applications, apart from cost, efficiency of design is an important
characteristic. A useful way to reduce the size of electronic
equipment in the electric vehicles is proposed in this paper. The
technique simplifies the mechanical complexity and maximizes the
energy usage using the latest converter control techniques. Moreover
a bidirectional battery charger for hybrid electric vehicles is also
implemented in this paper. Several simulations on the test system
have been carried out in Matlab/Simulink environment. The results
exemplify the robustness of the proposed design methodology in case
of a 1.5 KW DC-DC converter.
Abstract: This study proposes the transformation of nonlinear
Magnetic Levitation System into linear one, via state and feedback
transformations using explicit algorithm. This algorithm allows
computing explicitly the linearizing state coordinates and feedback
for any nonlinear control system, which is feedback linearizable,
without solving the Partial Differential Equations. The algorithm is
performed using a maximum of N-1 steps where N being the
dimension of the system.
Abstract: The study was conducted to evaluate the efficiency of
Garlic and Chili combination solution on control of insect pests in
cabbage crop. The solution was sprayed at different intervals after
transplanting. The efficiency of Garlic and chili combination solution
on cabbage insect pests was measured. Results revealed that Garlic
and chili combination solution was the effectively reduced cabbage
insect pests. On other hand, the spray solution not only reduced the
number of days required for the cabbage growth but also greatly
enhanced the leaf number, head diameter, head weight, and quality of
cabbage. Garlic and chili combination solution have positive effects
on pests reduction and improve growth, yield and quality of cabbage
vegetable.
Abstract: In MANET, mobile nodes communicate with each
other using the wireless channel where transmission takes place with
significant interference. The wireless medium used in MANET is a
shared resource used by all the nodes available in MANET. Packet
reserving is one important resource management scheme which
controls the allocation of bandwidth among multiple flows through
node cooperation in MANET. This paper proposes packet reserving
and clogging control via Routing Aware Packet Reserving (RAPR)
framework in MANET. It mainly focuses the end-to-end routing
condition with maximal throughput. RAPR is complimentary system
where the packet reserving utilizes local routing information
available in each node. Path setup in RAPR estimates the security
level of the system, and symbolizes the end-to-end routing by
controlling the clogging. RAPR reaches the packet to the destination
with high probability ratio and minimal delay count. The standard
performance measures such as network security level,
communication overhead, end-to-end throughput, resource utilization
efficiency and delay measure are considered in this work. The results
reveals that the proposed packet reservation and clogging control via
Routing Aware Packet Reserving (RAPR) framework performs well
for the above said performance measures compare to the existing
methods.
Abstract: In this paper, design of solid-state battery/supercapacitor emulator based on dc-dc boost converter is described.
The emulator mimics charging behavior of any storage device based
on a predefined behavior set by the user. The device is operated by a
two-level control structure: high-level emulating controller and low-
level input voltage controller. Simulation and experimental results are
shown to demonstrate the emulator operation.
Abstract: In this paper, we present a comparative assessment of
Space Vector Pulse Width Modulation (SVPWM) and Model
Predictive Control (MPC) for two-level three phase (2L-3P) Voltage
Source Inverter (VSI). VSI with associated system is subjected to
both control techniques and the results are compared.
Matlab/Simulink was used to model, simulate and validate the
control schemes. Findings of this study show that MPC is superior to
SVPWM in terms of total harmonic distortion (THD) and
implementation.
Abstract: This paper presents a new method to design nonlinear
feedback linearization controller for PEMFCs (Polymer Electrolyte
Membrane Fuel Cells). A nonlinear controller is designed based on
nonlinear model to prolong the stack life of PEMFCs. Since it is
known that large deviations between hydrogen and oxygen partial
pressures can cause severe membrane damage in the fuel cell,
feedback linearization is applied to the PEMFC system so that the
deviation can be kept as small as possible during disturbances or load
variations. To obtain an accurate feedback linearization controller,
tuning the linear parameters are always important. So in proposed
study NSGA (Non-Dominated Sorting Genetic Algorithm)-II method
was used to tune the designed controller in aim to decrease the
controller tracking error. The simulation result showed that the
proposed method tuned the controller efficiently.
Abstract: This paper presents a model predictive control (MPC)
of a utility interactive (UI) single phase inverter (SPI) for a
photovoltaic (PV) system at residential/distribution level. The
proposed model uses single-phase phase locked loop (PLL) to
synchronize SPI with the grid and performs MPC control in a dq
reference frame. SPI model consists of boost converter (BC),
maximum power point tracking (MPPT) control, and a full bridge
(FB) voltage source inverter (VSI). No PI regulators to tune and
carrier and modulating waves are required to produce switching
sequence. Instead, the operational model of VSI is used to synthesize
sinusoidal current and track the reference. Model is validated using a
three kW PV system at the input of UI-SPI in Matlab/Simulink.
Implementation and results demonstrate simplicity and accuracy, as
well as reliability of the model.
Abstract: This paper presents a hybrid three phase rectifier for
high power factor application. This rectifier is composed by zero
voltage transition (ZVT) and zero current transition (ZCT) boost
converter with three phase diode bridge rectifier, in parallel with a six
pulse three phase pulse width modulation (PWM) controlled rectifier.
The proposed topology is capable of high power factor with DC
output voltage regulation by providing sinusoidal input. Also, it
increases the overall efficiency of the new hybrid rectifier to 94.56%
and the total harmonic distortion of the hybrid structure varies from
0% to 16% at nominal output power. This topology was simulated in
MATLAB/SIMULINK environment and the output waveforms
presented with experimental result.
Abstract: Advances technology in the field of photogrammetry
replaces analog cameras with reflection on aircraft GPS/IMU system
with a digital aerial camera. In this system, when determining the
position of the camera with the GPS, camera rotations are also
determined by the IMU systems. All around the world, digital aerial
cameras have been used for the photogrammetry applications in the
last ten years. In this way, in terms of the work done in
photogrammetry it is possible to use time effectively, costs to be
reduced to a minimum level, the opportunity to make fast and
accurate.
Geo-referencing techniques that are the cornerstone of the GPS /
INS systems, photogrammetric triangulation of images required for
balancing (interior and exterior orientation) brings flexibility to the
process. Also geo-referencing process; needed in the application of
photogrammetry targets to help to reduce the number of ground
control points. In this study, the use of direct and indirect georeferencing
techniques on the accuracy of the points was investigated
in the production of photogrammetric mapping.
Abstract: The organizations of European and Czech critical
infrastructure have specific position, mission, characteristics and
behaviour in European Union and Czech state/business environments,
regarding specific requirements for regional and global security
environments. They must respect policy of national security and
global rules, requirements and standards in all their inherent and
outer processes of supply - customer chains and networks. A
controlling is generalized capability to have control over situational
policy. This paper aims and purposes are to introduce the controlling
as quite new necessary process attribute providing for critical
infrastructure is environment the capability and profit to achieve its
commitment regarding to the effectiveness of the quality
management system in meeting customer/ user requirements and also
the continual improvement of critical infrastructure organization’s
processes overall performance and efficiency, as well as its societal
security via continual planning improvement via DYVELOP
modelling.
Abstract: Diabetes is a growing health problem in worldwide.
Especially, the patients with Type 1 diabetes need strict glycemic
control because they have deficiency of insulin production. This
paper attempts to control blood glucose based on body mathematical
body model. The Bergman minimal mathematical model is used to
develop the nonlinear controller. A novel back-stepping based sliding
mode control (B-SMC) strategy is proposed as a solution that
guarantees practical tracking of a desired glucose concentration. In
order to show the performance of the proposed design, it is compared
with conventional linear and fuzzy controllers which have been done
in previous researches. The numerical simulation result shows the
advantages of sliding mode back stepping controller design to linear
and fuzzy controllers.
Abstract: The mathematical analysis on radiation obtained and
the development of the solar photovoltaic (PV) array groundwater
pumping is needed in the rural areas of Thohoyandou for sizing and
power performance subject to the climate conditions within the area.
A simple methodology approach is developed for the directed
coupled solar, controller and submersible ground water pump system.
The system consists of a PV array, pump controller and submerged
pump, battery backup and charger controller. For this reason, the
theoretical solar radiation is obtained for optimal predictions and
system performance in order to achieve different design and
operating parameters. Here the examination of the PV schematic
module in a Direct Current (DC) application is used for obtainable
maximum solar power energy for water pumping. In this paper, a
simple efficient photovoltaic water pumping system is presented with
its theoretical studies and mathematical modeling of photovoltaics
(PV) system.
Abstract: Calcium phosphate coating (CaP) has been employed
for protein delivery, but the typical direct protein adsorption on the
coating led to low incorporation content and fast release of the
protein from the coating. By using bovine serum albumin (BSA) as a
model protein, rapid biomimetic co-precipitation between calcium
phosphate and BSA was employed to control the distribution of BSA
within calcium phosphate coating during biomimetic formation on
titanium surface for only 6 h at 50oC in an accelerated calcium
phosphate solution. As a result, the amount of BSA incorporation and
release duration could be increased by using a rapid biomimetic coprecipitation
technique. Up to 43 fold increases in the BSA
incorporation content and the increase from 6 h to more than 360 h in
release duration compared to typical direct adsorption technique were
observed depending on the initial BSA concentration used during coprecipitation
(1, 10 and 100 μg.ml-1). From x-ray diffraction and
Fourier transform infrared spectroscopy studies, the coating
composition was not altered with the incorporation of BSA by this
rapid biomimetic co-precipitation and mainly comprised octacalcium
phosphate and hydroxyapatite. However, the microstructure of
calcium phosphate crystals changed from straight, plate-like units to
curved, plate-like units with increasing BSA content.
Abstract: To mimic the natural circumstances of cell growth in an organism, we present three-dimensional (3D) scaffolds fabricated by microfluidics for cultivation. This work investigates the cellular behaviors of rat cardiomyocytes in gelatin 3D scaffolds compared to those on 2D control, such as proliferation, viability and morphology. We found that the scaffolds may induce skeletal differentiation of H9c2 cells.
Abstract: Copper being one of the major intrinsic residual
impurities in steel possesses the tendency to induce severe
microstructural distortions if not controlled within certain limits.
Hence, this paper investigates the effect of this element on the
mechanical properties of construction steel with a view to ascertain
its safe limits for effective control. The experiment entails collection
of statistically scheduled samples of hot rolled profiles with varied
copper concentrations in the range of 0.12-0.39 wt. %. From these
samples were prepared standard test specimens subjected to tensile,
impact, hardness and microstructural analyses. Results show a rather
huge compromise in mechanical properties as the specimens
demonstrated 54.3%, 74.2% and 64.9% reduction in tensile strength,
impact energy and hardness respectively as copper content increases
from 0.12 wt. % to 0.39 wt. %. The steel’s abysmal performance is
due to the severe distortion of the microstructure occasioned by the
development of incoherent complex compounds which weaken the
pearlite reinforcing phase. It is concluded that the presence of copper
above 0.22 wt. % is deleterious to construction steel performance.
Abstract: Ficus deltoidea from the Moraceae family is a popular
medicinal herb in Malaysia. It possesses strong antioxidant and antiinflammatory
properties. In the present study, the anti-inflammatory
effects of F. deltoidea extract on UVB-irradiated HaCaT
Keratinocytes were investigated. HaCaT Keratinocytes were UVBirradiated
(12.5 mJ/cm3) and were treated with 0.05, 0.08 or 0.1% of
F. deltoidea extract. Cell viability following UVB irradiation was
significantly higher in the groups treated with the F. deltoidea extract
at doses of 0.05, 0.08 or 0.1% than in control group with UVB
irradiation only. Tumor necrosis factor-α (TNF-α), interleukin-1α
(IL-1α), interleukin-6 (IL-6) and cyclooxygenase (COX-2) play
primary roles in the inflammation process upon UV irradiation and
are known to be stimulated by UVB irradiation. Treatment with the
F. deltoidea extract dramatically inhibited the UV-induced TNF-α,
IL-1α, IL-6, and COX-2 expression. These results suggest that the F.
deltoidea extract inhibits the production of pro-inflammatory
cytokines and may be an effective protective agent for the treatment
of skin diseases.
Abstract: Access control is one of the most challenging issues
facing information security. Access control is defined as, the ability to
permit or deny access to a particular computational resource or digital
information by an unauthorized user or subject. The concept of usage
control (UCON) has been introduced as a unified approach to capture a
number of extensions for access control models and systems. In
UCON, an access decision is determined by three factors:
authorizations, obligations and conditions. Attribute mutability and
decision continuity are two distinct characteristics introduced by
UCON for the first time. An observation of UCON components
indicates that, the components are predefined and static. In this paper,
we propose a new and flexible model of usage control for the creation
and elimination of some of these components; for example new
objects, subjects, attributes and integrate these with the original
UCON model. We also propose a model for concurrent usage
scenarios in UCON.
Abstract: A simple, accurate and precise direct spectrophotometric method has been developed for the determination of cefixime in tablets and capsules. The method is based on the reaction of cefixime with a mixture of potassium iodide and potassium iodate to form yellow coloured product in ethanol-distilled water medium at room temperature which absorbed maximally at 352 nm. The factors affecting the reaction product were carefully studied and optimized. The validation parameters based on International Conference on Harmonisation (ICH, USA) guidelines were followed. The effect of common excipients used as additives has been tested and the tolerance limit was calculated for the determination of cefixime. Beer’s law is obeyed in the concentration range of 4 – 24 ug mL-1 with apparent molar absorptivity of 1.52 × 104 L mol-1cm-1 and Sandell’s sensitivity of 0.033 ug/cm2/ 0.001 absorbance unit. The limits of detection and quantitation for the proposed method are 0.32 and 1.06 ug mL-1, respectively. The proposed method has been successfully applied for the determination of cefixime in pharmaceutical formulations. The results obtained by the proposed method were statistically compared with the reference method using t- and F- values and found no significant difference between the two methods. The proposed method can be used as an alternate method for routine quality control analysis of cefixime in pharmaceutical formulations.
Abstract: This paper deals with a protection of the national and
European infrastructure. It is issue nowadays. The paper deals with
the perspectives and possibilities of "smart solutions" to critical
infrastructure protection. The research project deals with computers
aided technologies are used from the perspective of new, better
protection of selected infrastructure objects. Protection is focused on
communication and information channels. These communication and
information channels are very important for the functioning of the
system of protection of critical infrastructure elements.