Abstract: In this paper, a few chattering-free Sliding Mode Controllers (SMC) are proposed to stabilize an Active Magnetic Bearing (AMB) system with gyroscopic effect that is proportional to the rotor speed. The improved switching terms of the controller inherited from the saturation-type function and boundary layer control technique is shown to be able to achieve bounded and asymptotic stability, respectively, while the chattering effect in the input is attenuated. This is proven to be advantageous for AMB system since minimization of chattering results in optimized control effort. The performance of each controller is demonstrated via result of simulation in which the measurement of the total consumed energy and maximum control magnitude of each controller illustrates the effectiveness of the proposed controllers.
Abstract: In modern era, the biggest challenge facing the
software industry is the upcoming of new technologies. So, the
software engineers are gearing up themselves to meet and manage
change in large software system. Also they find it difficult to deal
with software cognitive complexities. In the last few years many
metrics were proposed to measure the cognitive complexity of
software. This paper aims at a comprehensive survey of the metric of
software cognitive complexity. Some classic and efficient software
cognitive complexity metrics, such as Class Complexity (CC),
Weighted Class Complexity (WCC), Extended Weighted Class
Complexity (EWCC), Class Complexity due to Inheritance (CCI) and
Average Complexity of a program due to Inheritance (ACI), are
discussed and analyzed. The comparison and the relationship of these
metrics of software complexity are also presented.
Abstract: Gasoline Octane Number is the standard measure of
the anti-knock properties of a motor in platforming processes, that is
one of the important unit operations for oil refineries and can be
determined with online measurement or use CFR (Cooperative Fuel
Research) engines. Online measurements of the Octane number can
be done using direct octane number analyzers, that it is too
expensive, so we have to find feasible analyzer, like ANFIS
estimators.
ANFIS is the systems that neural network incorporated in fuzzy
systems, using data automatically by learning algorithms of NNs.
ANFIS constructs an input-output mapping based both on human
knowledge and on generated input-output data pairs.
In this research, 31 industrial data sets are used (21 data for training
and the rest of the data used for generalization). Results show that,
according to this simulation, hybrid method training algorithm in
ANFIS has good agreements between industrial data and simulated
results.
Abstract: One-way functions are functions that are easy to
compute but hard to invert. Their existence is an open conjecture; it
would imply the existence of intractable problems (i.e. NP-problems
which are not in the P complexity class).
If true, the existence of one-way functions would have an impact
on the theoretical framework of physics, in particularly, quantum
mechanics. Such aspect of one-way functions has never been shown
before.
In the present work, we put forward the following.
We can calculate the microscopic state (say, the particle spin in the
z direction) of a macroscopic system (a measuring apparatus
registering the particle z-spin) by the system macroscopic state (the
apparatus output); let us call this association the function F. The
question is: can we compute the function F in the inverse direction?
In other words, can we compute the macroscopic state of the system
through its microscopic state (the preimage F -1)?
In the paper, we assume that the function F is a one-way function.
The assumption implies that at the macroscopic level the Schrödinger
equation becomes unfeasible to compute. This unfeasibility plays a
role of limit of the validity of the linear Schrödinger equation.
Abstract: The increasingly sophisticated technologies have now been able to provide assistance for surgeons to improve surgical
performance through various training programs. Equally important to learning skills is the assessment method as it determines the learning and technical proficiency of a trainee. A consistent and
rigorous assessment system will ensure that trainees acquire the specific level of competency prior to certification. This paper
reviews the methods currently in use for assessment of surgical
skill and some modern techniques using computer-based
measurements and virtual reality systems for more quantitative
measurements
Abstract: An area-integrating method that uses the technique of total integrated light scatter for evaluating the root mean square height of the surface Sq has been presented in the paper. It is based on the measurement of the scatter power using a flat photodiode integrator rather than an optical sphere or a hemisphere. By this means, one can obtain much less expensive and smaller instruments than traditional ones. Thanks to this, they could find their application for surface control purposes, particularly in small and medium size enterprises. A description of the functioning of the measuring unit as well as the impact caused by different factors on its properties is presented first. Next, results of measurements of the Sq values performed for optical, silicon and metal samples have been shown. It has been also proven that they are in a good agreement with the results obtained using the Ulbricht sphere instrument.
Abstract: The purpose of the present study is to determine the level of reading habit of future classroom teachers, to discuss the obtained results according to their socio-demographic features and to define the factors which are influential on taking up reading in the context of future teachers experiences. The target population of the study consists of the fourth grade students at 62 faculties of education, department of classroom teaching from Turkish state universities. The sampling of the study consists of the fourth grade students from seven faculties of education, department of classroom teaching from each region. In the study, in the first and the second aspects, there will be a questionnaire to be developed concerning the measurement of future teachers level of reading habits and their socio-demographic features. The questionnaire was applied to all the students in the sample.
Abstract: A new paradigm for software design and development models software by its business process, translates the model into a process execution language, and has it run by a supporting execution engine. This process-oriented paradigm promotes modeling of software by less technical users or business analysts as well as rapid development. Since business process models may be shared by different organizations and sometimes even by different business domains, it is interesting to apply a technique used in traditional software component technology to design reusable business processes. This paper discusses an approach to apply a technique for software component fabrication to the design of process-oriented software units, called process components. These process components result from decomposing a business process of a particular application domain into subprocesses with an aim that the process components can be reusable in different process-based software models. The approach is quantitative because the quality of process component design is measured from technical features of the process components. The approach is also strategic because the measured quality is determined against business-oriented component management goals. A software tool has been developed to measure how good a process component design is, according to the required managerial goals and comparing to other designs. We also discuss how we benefit from reusable process components.
Abstract: This paper presents the experimental results of
discharge current phenomena on various humidity, temperature,
pressure and pollutant conditions of epoxy resin specimen. The
leakage distance of specimen was 3 cm, that it was supplied by high
voltage. The polluted condition was given with NaCl artificial
pollutant. The conducted measurements were discharge current and
applied voltage. The specimen was put in a hermetically sealed
chamber, and the current waveforms were analyzed with FFT.
The result indicated that on discharge condition, the fifth
harmonics still had dominant, rather than third one. The third
harmonics tent to be appeared on low pressure heavily polluted
condition, and followed by high humidity heavily polluted condition.
On the heavily polluted specimen, the peaks discharge current points
would be high and more frequent. Nevertheless, the specimen still
had capacitive property. Besides that, usually discharge current
points were more frequent. The influence of low pressure was still
dominant to be easier to discharge. The non-linear property would be
appear explicitly on low pressure and heavily polluted condition.
Abstract: Temperature dependence of force of gravitation is one
of the fundamental problems of physics. This problem has got special
value in connection with that the general theory of relativity,
supposing the weakest positive influence of a body temperature on its
weight, actually rejects an opportunity of measurement of negative
influence of temperature on gravity in laboratory conditions. Really,
the recognition of negative temperature dependence of gravitation,
for example, means basic impossibility of achievement of a
singularity («a black hole») at a gravitational collapse. Laboratory
experiments with exact weighing the heated up metal samples,
indicating negative influence temperatures of bodies on their physical
weight are described. Influence of mistakes of measurements is
analyzed. Calculations of distribution of temperature in volume of the
bar, agreed with experimental data of time dependence of weight of
samples are executed. The physical substantiation of negative
temperature dependence of weight of the bodies, based on correlation
of acceleration at thermal movement of micro-particles of a body and
its absolute temperature, are given.
Abstract: This paper presents the development of adaptive
distance relay for protection of parallel transmission line with mutual
coupling. The proposed adaptive relay, automatically adjusts its
operation based on the acquisition of the data from distance relay of
adjacent line and status of adjacent line from line circuit breaker IED
(Intelligent Electronic Device). The zero sequence current of the
adjacent parallel transmission line is used to compute zero sequence
current ratio and the mutual coupling effect is fully compensated.
The relay adapts to changing circumstances, like failure in
communication from other relays and non - availability of adjacent
transmission line. The performance of the proposed adaptive relay is
tested using steady state and dynamic test procedures. The fault
transients are obtained by simulating a realistic parallel transmission
line system with mutual coupling effect in PSCAD. The evaluation
test results show the efficacy of adaptive distance relay over the
conventional distance relay.
Abstract: A way of generating millimeter wave I/Q signal using inductive resonator matched poly-phase filter is suggested. Normally the poly-phase filter generates quite accurate I/Q phase and magnitude but the loss of the filter is considerable due to series connection of passive RC components. This loss term directly increases system noise figure when the poly-phase filter is used in RF Front-end. The proposed matching method eliminates above mentioned loss and in addition provides gain on the passive filter. The working algorithm is illustrated by mathematical analysis. The generated I/Q signal is used in implementing millimeter wave phase shifter for the 60 GHz communication system to verify its effectiveness. The circuit is fabricated in 90 nm TSMC RF CMOS process under 1.2 V supply voltage. The measurement results showed that the suggested method improved gain by 6.5 dB and noise by 2.3 dB. The summary of the proposed I/Q generation is compared with previous works.
Abstract: The literature reports a large number of approaches for
measuring the similarity between protein sequences. Most of these
approaches estimate this similarity using alignment-based techniques
that do not necessarily yield biologically plausible results, for two
reasons.
First, for the case of non-alignable (i.e., not yet definitively aligned
and biologically approved) sequences such as multi-domain, circular
permutation and tandem repeat protein sequences, alignment-based
approaches do not succeed in producing biologically plausible results.
This is due to the nature of the alignment, which is based on the
matching of subsequences in equivalent positions, while non-alignable
proteins often have similar and conserved domains in non-equivalent
positions.
Second, the alignment-based approaches lead to similarity measures
that depend heavily on the parameters set by the user for the alignment
(e.g., gap penalties and substitution matrices). For easily alignable
protein sequences, it's possible to supply a suitable combination of
input parameters that allows such an approach to yield biologically
plausible results. However, for difficult-to-align protein sequences,
supplying different combinations of input parameters yields different
results. Such variable results create ambiguities and complicate the
similarity measurement task.
To overcome these drawbacks, this paper describes a novel and
effective approach for measuring the similarity between protein
sequences, called SAF for Substitution and Alignment Free. Without
resorting either to the alignment of protein sequences or to substitution
relations between amino acids, SAF is able to efficiently detect the
significant subsequences that best represent the intrinsic properties of
protein sequences, those underlying the chronological dependencies of
structural features and biochemical activities of protein sequences.
Moreover, by using a new efficient subsequence matching scheme,
SAF more efficiently handles protein sequences that contain similar
structural features with significant meaning in chronologically
non-equivalent positions. To show the effectiveness of SAF, extensive
experiments were performed on protein datasets from different
databases, and the results were compared with those obtained by
several mainstream algorithms.
Abstract: The major part of light weight timber constructions
consists of insulation. Mineral wool is the most commonly used
insulation due to its cost efficiency and easy handling. The fiber
orientation and porosity of this insulation material enables flowthrough.
The air flow resistance is low. If leakage occurs in the
insulated bay section, the convective flow may cause energy losses
and infiltration of the exterior wall with moisture and particles. In
particular the infiltrated moisture may lead to thermal bridges and
growth of health endangering mould and mildew. In order to prevent
this problem, different numerical calculation models have been
developed. All models developed so far have a potential for
completion. The implementation of the flow-through properties of
mineral wool insulation may help to improve the existing models.
Assuming that the real pressure difference between interior and
exterior surface is larger than the prescribed pressure difference in the
standard test procedure for mineral wool ISO 9053 / EN 29053,
measurements were performed using the measurement setup for
research on convective moisture transfer “MSRCMT".
These measurements show, that structural inhomogeneities of
mineral wool effect the permeability only at higher pressure
differences, as applied in MSRCMT. Additional microscopic
investigations show, that the location of a leak within the
construction has a crucial influence on the air flow-through and the
infiltration rate. The results clearly indicate that the empirical values
for the acoustic resistance of mineral wool should not be used for the
calculation of convective transfer mechanisms.
Abstract: Controlled release urea has become popular in agricultural industry as it helps to solve environmental issues and increase crop yield. Recently biomass was identified to replace the polymer used as a coating material in the conventional coated urea. In this paper spreading and contact angle of biomass droplet (lignin, cellulose and clay) on urea surface are investigated experimentally. There were two tests were conducted, sessile drop for contact angle measurement and pendant drop for contact angle measurement. A different concentration of biomass droplet was released from 30 mm above a substrate. Glass was used as a controlled substrate. Images were recorded as soon as the droplet impacted onto the urea before completely adsorb into the urea. Digitized droplets were then used to identify the droplet-s surface tension and contact angle. There is large difference observed between the low surface tension and high surface tension liquids, where the wetting and spreading diameter is higher for lower surface tension. From the contact angle results, the data showed that the biomass coating films were possible as wetting liquid (θ < 90º). Contact angle of biomass coating material gives good indication for the wettablity of a liquid on urea surface.
Abstract: The paper deals with the estimation of amplitude and phase of an analogue multi-harmonic band-limited signal from irregularly spaced sampling values. To this end, assuming the signal fundamental frequency is known in advance (i.e., estimated at an independent stage), a complexity-reduced algorithm for signal reconstruction in time domain is proposed. The reduction in complexity is achieved owing to completely new analytical and summarized expressions that enable a quick estimation at a low numerical error. The proposed algorithm for the calculation of the unknown parameters requires O((2M+1)2) flops, while the straightforward solution of the obtained equations takes O((2M+1)3) flops (M is the number of the harmonic components). It is applied in signal reconstruction, spectral estimation, system identification, as well as in other important signal processing problems. The proposed method of processing can be used for precise RMS measurements (for power and energy) of a periodic signal based on the presented signal reconstruction. The paper investigates the errors related to the signal parameter estimation, and there is a computer simulation that demonstrates the accuracy of these algorithms.
Abstract: This paper present an effective method to accurately reconstruct and measure the 3D curve edges of small industrial parts based on stereo vision. To effectively fit the curve of the measured parts using a series of line segments in the images, a strategy from coarse to fine is employed based on multi-scale curve fitting. After reconstructing the 3D curve of a hole through a curved surface, its axis is adjusted so that it is parallel to the Z axis with least squares error and the dimensions of the hole can be calculated on the XY plane easily. Experimental results show that the presented method can accurately measure the dimensions of round holes through a curved surface.
Abstract: The thermal, epithermal and fast fluxes were
calculated for three irradiation channels at Egypt Second Research
Reactor (ETRR-2) using CITVAP code. The validity of the
calculations was verified by experimental measurements. There are
some deviations between measurements and calculations. This is due
to approximations in the calculation models used, homogenization of
regions, condensation of energy groups and uncertainty in nuclear
data used. Neutron flux data for the three irradiation channels are
now available. This would enable predicting the irradiation
conditions needed for future radioisotope production.
Abstract: In this study we investigate silica nanoparticle (SiO2- NP) effects on the structure and phase properties of supported lipid monolayers and bilayers, coupling surface pressure measurements, fluorescence microscopy and atomic force microscopy. SiO2-NPs typically in size range of 10nm to 100 nm in diameter are tested. Our results suggest first that lipid molecules organization depends to their nature. Secondly, lipid molecules in the vinicity of big aggregates nanoparticles organize in liquid condensed phase whereas small aggregates are localized in both fluid liquid-expanded (LE) and liquid-condenced (LC). We demonstrated also by atomic force microscopy that by measuring friction forces it is possible to get information as if nanoparticle aggregates are recovered or not by lipid monolayers and bilayers.
Abstract: Although agriculture is an important part of the world
economy, accounting in agriculture still has many shortcomings. The
adoption of IAS 41 “Agriculture” has tried to improve this situation
and increase the comparability of financial statements of entities in
the agricultural sector. Although controversial, IAS 41 is the first
step of a consistent transition to fair value assessment in the
agricultural sector. The objective of our work is the analysis of IAS
41 and current accounting agricultural situation in Romania.
Accounting regulations in Romania are in accordance with European
directives and, in many respects, converged with IFRS referential.
Provisions of IAS 41, however, are not reflected directly in
Romanian regulations. With the increase of forest land transactions,
it is expected that recognition and measurement of biological assets
under IAS 41 to become a necessity.