Abstract: This paper introduces a new approach for the performance
analysis of adaptive filter with error saturation nonlinearity in
the presence of impulsive noise. The performance analysis of adaptive
filters includes both transient analysis which shows that how fast
a filter learns and the steady-state analysis gives how well a filter
learns. The recursive expressions for mean-square deviation(MSD)
and excess mean-square error(EMSE) are derived based on weighted
energy conservation arguments which provide the transient behavior
of the adaptive algorithm. The steady-state analysis for co-related
input regressor data is analyzed, so this approach leads to a new
performance results without restricting the input regression data to
be white.
Abstract: The bypass exhaust system of a 160 MW combined cycle has been modeled and analyzed using numerical simulation in 2D prospective. Analysis was carried out using the commercial numerical simulation software, FLUENT 6.2. All inputs were based on the technical data gathered from working conditions of a Siemens V94.2 gas turbine, installed in the Yazd power plant. This paper deals with reduction of pressure drop in bypass exhaust system using turning vanes mounted in diverter box in order to alleviate turbulent energy dissipation rate above diverter box. The geometry of such turning vanes has been optimized based on the flow pattern at diverter box inlet. The results show that the use of optimized turning vanes in diverter box can improve the flow pattern and eliminate vortices around sharp edges just before the silencer. Furthermore, this optimization could decrease the pressure drop in bypass exhaust system and leads to higher plant efficiency.
Abstract: This paper describes the process used in the
automation of the Maritime UAV commands using the Kinect sensor.
The AR Drone is a Quadrocopter manufactured by Parrot [1] to be
controlled using the Apple operating systems such as iPhones and
Ipads. However, this project uses the Microsoft Kinect SDK and
Microsoft Visual Studio C# (C sharp) software, which are compatible
with Windows Operating System for the automation of the navigation
and control of the AR drone.
The navigation and control software for the Quadrocopter runs on
a windows 7 computer. The project is divided into two sections; the
Quadrocopter control system and the Kinect sensor control system.
The Kinect sensor is connected to the computer using a USB cable
from which commands can be sent to and from the Kinect sensors.
The AR drone has Wi-Fi capabilities from which it can be connected
to the computer to enable transfer of commands to and from the
Quadrocopter.
The project was implemented in C#, a programming language that
is commonly used in the automation systems. The language was
chosen because there are more libraries already established in C# for
both the AR drone and the Kinect sensor.
The study will contribute toward research in automation of
systems using the Quadrocopter and the Kinect sensor for navigation
involving a human operator in the loop. The prototype created has
numerous applications among which include the inspection of vessels
such as ship, airplanes and areas that are not accessible by human
operators.
Abstract: Removal of a reactive dye (Reactive blue 4) by
adsorption utilizing waste aluminium hydroxide sludge as an
adsorbent was investigated. The removal of the dye was optimized
using response surface methodology (RSM). In the RSM
experiments; initial dye concentration, adsorbent concentration and
contact time were critical parameters. RSM experiments were
performed at the range of initial dye concentration 31.82-368.18
mg/L, adsorbent concentration 3.18-36.82 g/L, contact time 15.82-
56.18 h. Optimum initial dye concentration, adsorbent concentration
and contact time were obtained as 108.83 mg/L, 29.36 g/L and 33.57
h respectively. At these conditions, maximum removal of the dye was
obtained as 95%. The experiments were performed at the optimum
conditions to verify these results and the same results were obtained.
Abstract: A solar refrigeration system based on the adsorptiondesorption
phenomena is designed and analyzed. An annular tubular
generator filled with silica gel adsorbent and with a perforated inner
cylinder is integrated within a flat solar collector. The working fluid
in the refrigeration cycle is water. The thermodynamic analysis and
because of the temperature level that could be attained with a flat
solar collector it is required that the system operates under vacuum
conditions. In order to enhance the performance of the system and to
get uniform temperature in the silica gel and higher desorbed mass,
an apparatus for rotation of the generator is incorporated in the
system. Testing is carried out and measurements are taken on the
designed installation. The effect of rotation is checked on the
temperature distribution and on the performance of this machine and
compared to the flat solar collector with fixed generator.
Abstract: This paper presents a fuzzy logic controlled shunt
active power filter used to compensate for harmonic distortion in three-phase four-wire systems. The shunt active filter employs a
simple method for the calculation of the reference compensation current based of Fast Fourier Transform. This presented filter is able
to operate in both balanced and unbalanced load conditions. A fuzzy
logic based current controller strategy is used to regulate the filter current and hence ensure harmonic free supply current. The validity
of the presented approach in harmonic mitigation is verified via
simulation results of the proposed test system under different loading
conditions.
Abstract: A combination of image fusion and quad tree decomposition method is used for detecting the sunspot trajectories in each month and computation of the latitudes of these trajectories in each solar hemisphere. Daily solar images taken with SOHO satellite are fused for each month and the result of fused image is decomposed with Quad Tree decomposition method in order to classifying the sunspot trajectories and then to achieve the precise information about latitudes of sunspot trajectories. Also with fusion we deduce some physical remarkable conclusions about sun magnetic fields behavior. Using quad tree decomposition we give information about the region on sun surface and the space angle that tremendous flares and hot plasma gases permeate interplanetary space and attack to satellites and human technical systems. Here sunspot images in June, July and August 2001 are used for studying and give a method to compute the latitude of sunspot trajectories in each month with sunspot images.
Abstract: Modeling transfer phenomena in several chemical
engineering operations leads to the resolution of partial differential
equations systems. According to the complexity of the operations
mechanisms, the equations present a nonlinear form and analytical
solution became difficult, we have then to use numerical methods
which are based on approximations in order to transform a
differential system to an algebraic one.Finite element method is one
of numerical methods which can be used to obtain an accurate
solution in many complex cases of chemical engineering.The packed
columns find a large application like contactor for liquid-liquid
systems such solvent extraction. In the literature, the modeling of this
type of equipment received less attention in comparison with the
plate columns.A mathematical bidimensionnal model with radial and
axial dispersion, simulating packed tower extraction behavior was
developed and a partial differential equation was solved using the
finite element method by adopting the Galerkine model. We
developed a Mathcad program, which can be used for a similar
equations and concentration profiles are obtained along the column.
The influence of radial dispersion was prooved and it can-t be
neglected, the results were compared with experimental concentration
at the top of the column in the extraction system:
acetone/toluene/water.
Abstract: We address the balancing problem of transfer lines in
this paper to find the optimal line balancing that minimizes the nonproductive
time. We focus on the tool change time and face
orientation change time both of which influence the makespane. We
consider machine capacity limitations and technological constraints
associated with the manufacturing process of auto cylinder heads.
The problem is represented by a mixed integer programming model
that aims at distributing the design features to workstations and
sequencing the machining processes at a minimum non-productive
time. The proposed model is solved by an algorithm established using
linearization schemes and Benders- decomposition approach. The
experiments show the efficiency of the algorithm in reaching the
exact solution of small and medium problem instances at reasonable
time.
Abstract: A good green building design project, designers should consider not only energy consumption, but also healthy and comfortable needs of inhabitants. In recent years, the Taiwan government paid attentions on both carbon reduction and indoor air quality issues, which be presented in the legislation of Building Codes and other regulations. Taiwan located in hot and humid climates, dampness in buildings leads to significant microbial pollution and building damage. This means that the high temperature and humidity present a serious indoor air quality issue. The interactions between vapor transfers and energy fluxes are essential for the whole building Heat Air and Moisture (HAM) response. However, a simulation tool with short calculation time, property accuracy and interface is needed for practical building design processes. In this research, we consider the vapor transfer phenomenon of building materials as well as temperature and humidity and energy consumption in a building space. The simulation bases on the EMPD method, which was performed by EnergyPlus, a simulation tool developed by DOE, to simulate the indoor moisture variation in a one-zone residential unit based on the Effective Moisture Penetration Depth Method, which is more suitable for practical building design processes.
Abstract: In the present study, Convective heat transfer
coefficient and pressure drop of Al2O3/water nanofluid in laminar
flow regime under constant heat flux conditions inside a circular tube
were experimentally investigated. Al2O3/water nanofluid with 0.5%
and 1% volume concentrations with 15 nm diameter nanoparticles
were used as working fluid. The effect of different volume
concentrations on convective heat transfer coefficient and friction
factor was studied. The results emphasize that increasing of particle
volume concentration leads to enhance convective heat transfer
coefficient. Measurements show the average heat transfer coefficient
enhanced about 11-20% with 0.5% volume concentration and
increased about 16-27% with 1% volume concentration compared to
distilled water. In addition, the convective heat transfer coefficient of
nanofluid enhances with increase in heat flux. From the results, the
average ratio of (fnf/fbf) was about 1.10 for 0.5% volume
concentration. Therefore, there is no significant increase in friction
factor for nanofluids.
Abstract: This paper present a circular patch microstrip array antenna operate in KU-band (10.9GHz – 17.25GHz). The proposed circular patch array antenna will be in light weight, flexible, slim and compact unit compare with current antenna used in KU-band. The paper also presents the detail steps of designing the circular patch microstrip array antenna. An Advance Design System (ADS) software is used to compute the gain, power, radiation pattern, and S11 of the antenna. The proposed Circular patch microstrip array antenna basically is a phased array consisting of 'n' elements (circular patch antennas) arranged in a rectangular grid. The size of each element is determined by the operating frequency. The incident wave from satellite arrives at the plane of the antenna with equal phase across the surface of the array. Each 'n' element receives a small amount of power in phase with the others. There are feed network connects each element to the microstrip lines with an equal length, thus the signals reaching the circular patches are all combined in phase and the voltages add up. The significant difference of the circular patch array antenna is not come in the phase across the surface but in the magnitude distribution.
Abstract: Human middle-ear is the key component of the
auditory system. Its function is to transfer the sound waves through
the ear canal to provide sufficient stimulus to the fluids of the inner
ear. Degradation of the ossicles that transmit these sound waves from
the eardrum to the inner ear leads to hearing loss. This problem can
be overcome by replacing one or more of these ossicles by middleear
prosthesis. Designing such prosthesis requires a comprehensive
knowledge of the biomechanics of the middle-ear. There are many
finite element modeling approaches developed to understand the
biomechanics of the middle ear. The available models in the
literature, involve high computation time. In this paper, we propose a
simplified model which provides a reasonably accurate result with
much less computational time. Simulation results indicate a
maximum sound pressure gain of 10 dB at 5500 Hz.
Abstract: The paper deals with the kinematics and automated
calculation of intermittent mechanisms with radial cams. Currently,
electronic cams are increasingly applied in the drives of working link
mechanisms. Despite a huge advantage of electronic cams in their reprogrammability
or instantaneous change of displacement diagrams,
conventional cam mechanisms have an irreplaceable role in
production and handling machines. With high frequency of working
cycle periods, the dynamic load of the proper servomotor rotor
increases and efficiency of electronic cams strongly decreases.
Though conventional intermittent mechanisms with radial cams are
representatives of fixed automation, they have distinct advantages in
their high speed (high dynamics), positional accuracy and relatively
easy manufacture. We try to remove the disadvantage of firm
displacement diagram by reducing costs for simple design and
automated calculation that leads reliably to high-quality and
inexpensive manufacture.
Abstract: The aim of study was to evaluate pressure distribution characteristics of the elastic textile bandages using two instrumental techniques: a prototype Instrument and a load Transference. The prototype instrument which simulates shape of real leg has pressure sensors which measure bandage pressure. Using this instrument, the results show that elastic textile bandages presents different pressure distribution characteristics and none produces a uniform distribution around lower limb.
The load transference test procedure is used to determine whether a relationship exists between elastic textile bandage structure and pressure distribution characteristics. The test procedure assesses degree of load, directly transferred through a textile when loads series are applied to bandaging surface. A range of weave fabrics was produced using needle weaving machine and a sewing technique. A textile bandage was developed with optimal characteristics far superior pressure distribution than other bandages. From results, we find that theoretical pressure is not consistent exactly with practical pressure. It is important in this study to make a practical application for specialized nurses in order to verify the results and draw useful conclusions for predicting the use of this type of elastic band.
Abstract: This study investigates the capacity of granular
activated carbon (GAC) for the storage of methane through the
equilibrium adsorption. An experimental apparatus consist of a dual
adsorption vessel was set up for the measurement of equilibrium
adsorption of methane on GAC using volumetric technique (pressure
decay). Experimental isotherms of methane adsorption were
determined by the measurement of equilibrium uptake of methane in
different pressures (0-50 bar) and temperatures (285.15-328.15°K).
The experimental data was fitted to Freundlich and Langmuir
equations to determine the model isotherm. The results show that the
experimental data is equally well fitted by the both model isotherms.
Using the experimental data obtained in different temperatures the
isosteric heat of methane adsorption was also calculated by the
Clausius-Clapeyron equation from the Sips isotherm model. Results
of isosteric heat of adsorption show that decreasing temperature or
increasing methane uptake by GAC decrease the isosteric heat of
methane adsorption.
Abstract: One of the most importance of intelligence in-car and
roadside systems is the cooperative vehicle-infrastructure system. In
Thailand, ITS technologies are rapidly growing and real-time vehicle
information is considerably needed for ITS applications; for example,
vehicle fleet tracking and control and road traffic monitoring
systems. This paper defines the communication protocols and
software design for middleware components of B-VIS (Burapha
Vehicle-Infrastructure System). The proposed B-VIS middleware architecture serves the needs of a distributed RFID sensor network and simplifies some intricate details of several communication standards.
Abstract: Dealing with hundreds of features in character
recognition systems is not unusual. This large number of features
leads to the increase of computational workload of recognition
process. There have been many methods which try to remove
unnecessary or redundant features and reduce feature dimensionality.
Besides because of the characteristics of Farsi scripts, it-s not
possible to apply other languages algorithms to Farsi directly. In this
paper some methods for feature subset selection using genetic
algorithms are applied on a Farsi optical character recognition (OCR)
system. Experimental results show that application of genetic
algorithms (GA) to feature subset selection in a Farsi OCR results in
lower computational complexity and enhanced recognition rate.
Abstract: This paper presents a method to detect multiple cracks
based on frequency information. When a structure is subjected to
dynamic or static loads, cracks may develop and the modal
frequencies of the cracked structure may change. To detect cracks in a
structure, we construct a high precision wavelet finite element (EF)
model of a certain structure using the B-spline wavelet on the interval
(BSWI). Cracks can be modeled by rotational springs and added to the
FE model. The crack detection database will be obtained by solving
that model. Then the crack locations and depths can be determined
based on the frequency information from the database. The
performance of the proposed method has been numerically verified by
a rotor example.
Abstract: Polarization modulation infrared reflection absorption
spectroscopy (PM-IRRAS) in combination with electrochemistry,
was employed to study the influence of surface charge (potential) on
the kinetics of bovine serum albumin (BSA) adsorption on a
biomedical-grade 316LVM stainless steel surface is discussed. The
BSA adsorption kinetics was found to greatly depend on the surface
potential. With an increase in surface potential towards more
negative values, both the BSA initial adsorption rate and the
equilibrium (saturated) surface concentration also increased. Both
effects were explained on the basis of replacement of well-ordered
water molecules at the 316LVM / solution interface, i.e. by the
increase in entropy of the system.