Abstract: Removal of a reactive dye (Reactive blue 4) by
adsorption utilizing waste aluminium hydroxide sludge as an
adsorbent was investigated. The removal of the dye was optimized
using response surface methodology (RSM). In the RSM
experiments; initial dye concentration, adsorbent concentration and
contact time were critical parameters. RSM experiments were
performed at the range of initial dye concentration 31.82-368.18
mg/L, adsorbent concentration 3.18-36.82 g/L, contact time 15.82-
56.18 h. Optimum initial dye concentration, adsorbent concentration
and contact time were obtained as 108.83 mg/L, 29.36 g/L and 33.57
h respectively. At these conditions, maximum removal of the dye was
obtained as 95%. The experiments were performed at the optimum
conditions to verify these results and the same results were obtained.
Abstract: Land degradation is of concern in many countries. People more and more must address the problems associated with the degradation of soil properties due to man. Increasingly, organic soil amendments, such as compost are being examined for their potential use in soil restoration and for preventing soil erosion. In the Czech Republic, compost is the most used to improve soil structure and increase the content of soil organic matter. Land reclamation / restoration is one of the ways to evaluate industrially produced compost because Czech farmers are not willing to use compost as organic fertilizer. The most common use of reclamation substrates in the Czech Republic is for the rehabilitation of landfills and contaminated sites.
This paper deals with the influence of reclamation substrates (RS) with different proportions of compost and sand on selected soil properties–chemical characteristics, nitrogen bioavailability, leaching of mineral nitrogen, respiration activity and plant biomass production. Chemical properties vary proportionally with addition of compost and sand to the control variant (topsoil). The highest differences between the variants were recorded in leaching of mineral nitrogen (varies from 1.36mg dm-3 in C to 9.09mg dm-3). Addition of compost to soil improves conditions for plant growth in comparison with soil alone. However, too high addition of compost may have adverse effects on plant growth. In addition, high proportion of compost increases leaching of mineral N. Therefore, mixture of 70% of soil with 10% of compost and 20% of sand may be recommended as optimal composition of RS.
Abstract: This study aims to identify the current situation and
problems of environmental statement for major four home appliances
(refrigerators, washing machines, air conditioners and television
receivers) sold at online stores in Japan, and then to suggest how to
improve the situation, through a questionnaire survey conducted
among businesses that operate online stores and online malls with
multiple online stores. Results of the study boil down to:
(1) It is found out that environmental statement for the home
appliances at online stores have four problems; (i) less information
on “three Rs" and “chemical substances" than the one on “energy
conservation", (ii) cost for providing environmental statement, (iii)
issues associated with a label and mark placement, and (iv) issues
associated with energy conservation statement.
(2) Improvements are suggested for each of the four problems listed
above, and shown are (i) the effectiveness of, and need to promote, a
label and mark placement, (ii) cost burden on buyers, and (iii) need
of active efforts made by businesses and of dissemination of legal
regulations to businesses.
Abstract: Distant-talking voice-based HCI system suffers from
performance degradation due to mismatch between the acoustic
speech (runtime) and the acoustic model (training). Mismatch is
caused by the change in the power of the speech signal as observed at
the microphones. This change is greatly influenced by the change in
distance, affecting speech dynamics inside the room before reaching
the microphones. Moreover, as the speech signal is reflected, its
acoustical characteristic is also altered by the room properties. In
general, power mismatch due to distance is a complex problem. This
paper presents a novel approach in dealing with distance-induced
mismatch by intelligently sensing instantaneous voice power variation
and compensating model parameters. First, the distant-talking speech
signal is processed through microphone array processing, and the
corresponding distance information is extracted. Distance-sensitive
Gaussian Mixture Models (GMMs), pre-trained to capture both
speech power and room property are used to predict the optimal
distance of the speech source. Consequently, pre-computed statistic
priors corresponding to the optimal distance is selected to correct
the statistics of the generic model which was frozen during training.
Thus, model combinatorics are post-conditioned to match the power
of instantaneous speech acoustics at runtime. This results to an
improved likelihood in predicting the correct speech command at
farther distances. We experiment using real data recorded inside two
rooms. Experimental evaluation shows voice recognition performance
using our method is more robust to the change in distance compared
to the conventional approach. In our experiment, under the most
acoustically challenging environment (i.e., Room 2: 2.5 meters), our
method achieved 24.2% improvement in recognition performance
against the best-performing conventional method.
Abstract: In the last two decades radiofrequency ablation (RFA)
has been considered a promising medical procedure for the treatment
of primary and secondary malignancies. However, the needle-based
electrodes so far developed for this kind of treatment are not suitable
for the thermal ablation of tumors located in hollow organs like
esophagus, colon or bile duct. In this work a tubular electrode
solution is presented. Numerical and experimental analyses were
performed to characterize the volume of the lesion induced. Results
show that this kind of electrode is a feasible solution and numerical
simulation might provide a tool for planning RFA procedure with
some accuracy.
Abstract: In this paper, acoustic techniques are used to detect hidden insect infestations of date palm tress (Phoenix dactylifera L.). In particular, we use an acoustic instrument for early discovery of the presence of a destructive insect pest commonly known as the Red Date Palm Weevil (RDPW) and scientifically as Rhynchophorus ferrugineus (Olivier). This type of insect attacks date palm tress and causes irreversible damages at late stages. As a result, the infected trees must be destroyed. Therefore, early presence detection is a major part in controlling the spread and economic damage caused by this type of infestation. Furthermore monitoring and early detection of the disease can asses in taking appropriate measures such as isolating or treating the infected trees. The acoustic system is evaluated in terms of its ability for early discovery of hidden bests inside the tested tree. When signal acquisitions is completed for a number of date palms, a signal processing technique known as time-frequency analysis is evaluated in terms of providing an estimate that can be visually used to recognize the acoustic signature of the RDPW. The testing instrument was tested in the laboratory first then; it was used on suspected or infested tress in the field. The final results indicate that the acoustic monitoring approach along with signal processing techniques are very promising for the early detection of presence of the larva as well as the adult pest in the date palms.
Abstract: Faults in a network may take various forms such as hardware/software errors, vertex/edge faults, etc. Folded hypercube is a well-known variation of the hypercube structure and can be constructed from a hypercube by adding a link to every pair of nodes with complementary addresses. Let FFv (respectively, FFe) be the set of faulty nodes (respectively, faulty links) in an n-dimensional folded hypercube FQn. Hsieh et al. have shown that FQn - FFv - FFe for n ≥ 3 contains a fault-free cycle of length at least 2n -2|FFv|, under the constraints that (1) |FFv| + |FFe| ≤ 2n - 4 and (2) every node in FQn is incident to at least two fault-free links. In this paper, we further consider the constraints |FFv| + |FFe| ≤ 2n - 3. We prove that FQn - FFv - FFe for n ≥ 5 still has a fault-free cycle of length at least 2n - 2|FFv|, under the constraints : (1) |FFv| + |FFe| ≤ 2n - 3, (2) |FFe| ≥ n + 2, and (3) every vertex is still incident with at least two links.
Abstract: The more recent satellite projects/programs makes
extensive usage of real – time embedded systems. 16 bit processors
which meet the Mil-Std-1750 standard architecture have been used in
on-board systems. Most of the Space Applications have been written
in ADA. From a futuristic point of view, 32 bit/ 64 bit processors are
needed in the area of spacecraft computing and therefore an effort is
desirable in the study and survey of 64 bit architectures for space
applications. This will also result in significant technology
development in terms of VLSI and software tools for ADA (as the
legacy code is in ADA).
There are several basic requirements for a special processor for
this purpose. They include Radiation Hardened (RadHard) devices,
very low power dissipation, compatibility with existing operational
systems, scalable architectures for higher computational needs,
reliability, higher memory and I/O bandwidth, predictability, realtime
operating system and manufacturability of such processors.
Further on, these may include selection of FPGA devices, selection
of EDA tool chains, design flow, partitioning of the design, pin
count, performance evaluation, timing analysis etc.
This project deals with a brief study of 32 and 64 bit processors
readily available in the market and designing/ fabricating a 64 bit
RISC processor named RISC MicroProcessor with added
functionalities of an extended double precision floating point unit
and a 32 bit signal processing unit acting as co-processors. In this
paper, we emphasize the ease and importance of using Open Core
(OpenSparc T1 Verilog RTL) and Open “Source" EDA tools such as
Icarus to develop FPGA based prototypes quickly. Commercial tools
such as Xilinx ISE for Synthesis are also used when appropriate.
Abstract: This study aims at investigating factors in research
and development (R&D) growth and exploring the role of R&D
management in enhancing social innovation and productivity
improvement in Iran-s industrial sector. It basically explores the
common types of R&D activities and the industries which benefited
the most from active R&D units in Iran. The researchers generated
qualitative analyses obtained from primary and secondary data.
The primary data have been retrieved through interviews with five
key players (Managing Director, Internal Manager, General Manager,
Executive Manager, and Project Manager) in the industrial sector.
The secondary data acquired from an investigation on Mazandaran, a
province of northern Iran. The findings highlight Iran-s focuses of R
& D on cost reduction and upgrading productivity. Industries that
have benefited the most from active R&D units are metallic,
machinery and equipment design, and automotive.
We rank order the primary effects of R&D on productivity
improvement as follows, industry improvement, economic growth,
using professional human resources, generating productivity and
creativity culture, creating a competitive and innovative environment,
and increasing people-s knowledge.
Generally, low budget dedication and insufficient supply of highly
skilled scientists and engineers are two important obstacles for R&D
in Iran. Whereas, R&D has resulted in improvement in Iranian
society, transfer of contemporary knowledge into the international
market is still lacking.
Abstract: In the present work, behavior of inoxydable steel as
reinforcement bar in composite concrete is being investigated. The
bar-concrete adherence in reinforced concrete (RC) beam is studied
and focus is made on the tension stiffening parameter. This study
highlighted an approach to observe this interaction behavior in
bending test instead of direct tension as per reported in many
references. The approach resembles actual loading condition of the
structural RC beam. The tension stiffening properties are then
applied to numerical finite element analysis (FEA) to verify their
correlation with laboratory results. Comparison with laboratory
shows a good correlation between the two. The experimental settings
is able to determine tension stiffening parameters in RC beam and
the modeling strategies made in ABAQUS can closely represent the
actual condition. Tension stiffening model used can represent the
interaction properties between inoxydable steel and concrete.
Abstract: In this study, a 3D combustion chamber was simulated
using FLUENT 6.32. Aims to obtain accurate information about the
profile of the combustion in the furnace and also check the effect of
oxygen enrichment on the combustion process. Oxygen enrichment is
an effective way to reduce combustion pollutant. The flow rate of air
to fuel ratio is varied as 1.3, 3.2 and 5.1 and the oxygen enriched
flow rates are 28, 54 and 68 lit/min. Combustion simulations
typically involve the solution of the turbulent flows with heat
transfer, species transport and chemical reactions. It is common to
use the Reynolds-averaged form of the governing equation in
conjunction with a suitable turbulence model. The 3D Reynolds
Averaged Navier Stokes (RANS) equations with standard k-ε
turbulence model are solved together by Fluent 6.3 software. First
order upwind scheme is used to model governing equations and the
SIMPLE algorithm is used as pressure velocity coupling. Species
mass fractions at the wall are assumed to have zero normal
gradients.Results show that minimum mole fraction of CO2 happens
when the flow rate ratio of air to fuel is 5.1. Additionally, in a fixed
oxygen enrichment condition, increasing the air to fuel ratio will
increase the temperature peak. As a result, oxygen-enrichment can
reduce the CO2 emission at this kind of furnace in high air to fuel
rates.
Abstract: In order to realize long-lived electric propulsion
systems, we have been investigating an electrodeless plasma thruster.
In our concept, a helicon plasma is accelerated by the magnetic nozzle
for the thrusts production. In addition, the electromagnetic thrust can
be enhanced by the additional radio-frequency rotating electric field
(REF) power in the magnetic nozzle. In this study, a direct
measurement of the electromagnetic thrust and a probe measurement
have been conducted using a laboratory model of the thruster under the
condition without the REF power input. Fromthrust measurement, it is
shown that the thruster produces a sub-milli-newton order
electromagnetic thrust force without the additional REF power. The
thrust force and the density jump are observed due to the discharge
mode transition from the inductive coupled plasma to the helicon wave
excited plasma. The thermal thrust is theoretically estimated, and the
total thrust force, which is a sum of the electromagnetic and the
thermal thrust force and specific impulse are calculated to be up to 650
μN (plasma production power of 400 W, Ar gas mass flow rate of 1.0
mg/s) and 210 s (plasma production power of 400 W, Ar gas mass flow
rate of 0.2 mg/s), respectively.
Abstract: Mammography is the most effective procedure for an
early diagnosis of the breast cancer. Nowadays, people are trying to
find a way or method to support as much as possible to the
radiologists in diagnosis process. The most popular way is now being
developed is using Computer-Aided Detection (CAD) system to
process the digital mammograms and prompt the suspicious region to
radiologist. In this paper, an automated CAD system for detection
and classification of massive lesions in mammographic images is
presented. The system consists of three processing steps: Regions-Of-
Interest detection, feature extraction and classification. Our CAD
system was evaluated on Mini-MIAS database consisting 322
digitalized mammograms. The CAD system-s performance is
evaluated using Receiver Operating Characteristics (ROC) and Freeresponse
ROC (FROC) curves. The archived results are 3.47 false
positives per image (FPpI) and sensitivity of 85%.
Abstract: The objective of this study was to develop and compare alternative prediction equations of lean meat proportion (LMP) of lamb carcasses. Forty (40) male lambs, 22 of Churra Galega Bragançana Portuguese local breed and 18 of Suffolk breed were used. Lambs were slaughtered, and carcasses weighed approximately 30 min later in order to obtain hot carcass weight (HCW). After cooling at 4º C for 24-h a set of seventeen carcass measurements was recorded. The left side of carcasses was dissected into muscle, subcutaneous fat, inter-muscular fat, bone, and remainder (major blood vessels, ligaments, tendons, and thick connective tissue sheets associated with muscles), and the LMP was evaluated as the dissected muscle percentage. Prediction equations of LMP were developed, and fitting quality was evaluated through the coefficient of determination of estimation (R2 e) and standard error of estimate (SEE). Models validation was performed by k-fold crossvalidation and the coefficient of determination of prediction (R2 p) and standard error of prediction (SEP) were computed. The BT2 measurement was the best single predictor and accounted for 37.8% of the LMP variation with a SEP of 2.30%. The prediction of LMP of lamb carcasses can be based simple models, using as predictors the HCW and one fat thickness measurement.
Abstract: This paper describes an ongoing study into the quality of service provided by the Irish Revenue Commisioners- online tax filing and collection system. The Irish Revenue On-Line Service (ROS) site has won several awards. In this study, a version of the widely use SERVQUAL measuring instrument, adapted for use with online services, has been modified for the specific case of ROS. In this paper, the theory behind this instrument is set out, the particular problems of evaluating revenue collecting online are examined and the rationale for this approach is explained.
Abstract: This paper examines the relationship between financial
risks and profitability of the conventional and Islamic banks in
Malaysia for the period between 1996 and 2005. The measures of
profitability that have been used in the study are the return on equity
(ROE) and return on assets (ROA) while the financial risks are credit
risk, interest rate risk and liquidity risks. This study employs panel
data regression analysis of Generalised Least Squares of fixed effects
and random effects models. It was found that credit risk has a
significant impact on ROA and ROE for the conventional as well as
the Islamic banks. The relationship between interest rate risk and ROE
were found to be weakly significant for the conventional banks and
insignificant for the Islamic banks. The effect of interest rate risk on
ROA is significant for the conventional banks. Liquidity risk was
found to have an insignificant impact on both profitability measures.
Abstract: Column leach test has been performed to examine the
behavior of leaching of sodium, calcium and potassium in landfills.
In the column leach apparatus, two different layers of contaminated
and uncontaminated soils of different height ratios (ratio of depth of
contaminated soil to the depth of uncontaminated soil) are taken.
Water is poured from an overhead tank at a particular flowrate to the
inlet of the soil column for a certain ponding depth over the
contaminated soil. Subsequent infiltration causes leaching and the
leachates are collected from the bottom of the column. The
concentrations of Na, Ca and K in the leachate are measured using
flame photometry. The experiments are further extended by changing
the rates of flow from the overhead tank to the inlet of the column in
achieving the same ponding depth. The experiments are performed
for different scenarios in which the height ratios are altered and the
variations of concentrations of Na, Ca, and K are observed. The study
brings an estimation of leaching in landfill sites for different heights
and precipitation intensity where a ponding depth is maintained over
the landfill. It has been observed that the leaching behavior of Na,
Ca, and K are not similar. Calcium exhibits highest amount of
leaching compared to Sodium and Potassium under similar
experimental conditions.
Abstract: Sustainable energy usage has been recognized as one
of the important measure to increase the competitiveness of the
nation globally. Many strong emphases were given in the Ninth
Malaysia Plan (RMK9) to improve energy efficient especially to
government buildings. With this in view, a project to investigate the
potential of energy saving in selected building in Universiti Tun
Hussein Onn Malaysia (UTHM) was carried out. In this project, a
case study involving electric energy consumption of the academic
staff office building was conducted. The scope of the study include to
identify energy consumption in a selected building, to study energy
saving opportunities, to analyse cost investment in term of economic
and to identify users attitude with respect to energy usage. The
MS1525:2001, Malaysian Standard -Code of practice on energy
efficiency and use of renewable energy for non-residential buildings
was used as reference. Several energy efficient measures were
considered and their merits and priority were compared. Improving
human behavior can reduce energy consumption by 6% while
technical measure can reduce energy consumption by 44%. Two
economic analysis evaluation methods were applied; they are the
payback period method and net present value method.
Abstract: In this study, solid phase micro-extraction (SPME)
was optimized to improve the sensitivity and accuracy in
formaldehyde determination for plywood panels. Further work has
been carried out to compare the newly developed technique with
existing method which reacts formaldehyde collected in desiccators
with acetyl acetone reagent (DC-AA). In SPME, formaldehyde was
first derivatized with O-(2,3,4,5,6 pentafluorobenzyl)-hydroxylamine
hydrochloride (PFBHA) and analysis was then performed by gas
chromatography in combination with mass spectrometry (GC-MS).
SPME data subjected to various wood species gave satisfactory
results, with relative standard deviations (RSDs) obtained in the
range of 3.1-10.3%. It was also well correlated with DC values,
giving a correlation coefficient, RSQ, of 0.959. The quantitative
analysis of formaldehyde by SPME was an alternative in wood
industry with great potential
Abstract: Residual dye contents in textile dyeing wastewater have complex aromatic structures that are resistant to degrade in biological wastewater treatment. The objectives of this study were to determine the effectiveness of nanoscale zerovalent iron (NZVI) to decolorize Reactive Black 5 (RB5) and Reactive Red 198 (RR198) in synthesized wastewater and to investigate the effects of the iron particle size, iron dosage and solution pHs on the destruction of RB5 and RR198. Synthesized NZVI was confirmed by transmission electron microscopy (TEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The removal kinetic rates (kobs) of RB5 (0.0109 min-1) and RR198 (0.0111 min-1) by 0.5% NZVI were many times higher than those of microscale zerovalent iron (ZVI) (0.0007 min-1 and 0.0008 min-1, respectively). The iron dosage increment exponentially increased the removal efficiencies of both RB5 and RR198. Additionally, lowering pH from 9 to 5 increased the decolorization kinetic rates of both RB5 and RR198 by NZVI. The destruction of azo bond (N=N) in the chromophore of both reactive dyes led to decolorization of dye solutions.