Abstract: This paper puts forward one kind of air-fuel ratio
control method with PI controller. With the help of
MATLAB/SIMULINK software, the mathematical model of air-fuel
ratio control system for distributorless CNG engine is constructed.
The objective is to maintain cylinder-to-cylinder air-fuel ratio at a
prescribed set point, determined primarily by the state of the Three-
Way-Catalyst (TWC), so that the pollutants in the exhaust are
removed with the highest efficiency. The concurrent control of airfuel
under transient conditions could be implemented by Proportional
and Integral (PI) controller. The simulation result indicates that the
control methods can easily eliminate the air/fuel maldistribution and
maintain the air/fuel ratio at the stochiometry within minimum
engine events.
Abstract: The effect of the blade tip geometry of a high pressure
gas turbine is studied experimentally and computationally for high
speed leakage flows. For this purpose two simplified models are
constructed, one models a flat tip of the blade and the second models
a cavity tip of the blade. Experimental results are obtained from a
transonic wind tunnel to show the static pressure distribution along
the tip wall and provide flow visualization. RANS computations
were carried to provide further insight into the mean flow behavior
and to calculate the discharge coefficient which is a measure of the
flow leaking over the tip. It is shown that in both geometries of tip
the flow separates over the tip to form a separation bubble. The
bubble is higher for the cavity tip while a complete shock wave
system of oblique waves ending with a normal wave can be seen for
the flat tip. The discharge coefficient for the flat tip shows less
dependence on the pressure ratio over the blade tip than the cavity
tip. However, the discharge coefficient for the cavity tip is lower than
that of the flat tip, showing a better ability to reduce the leakage flow
and thus increase the turbine efficiency.
Abstract: A simultaneous study on indoor and outdoor particulate matter concentrations was done in five elementary schools in central parts of Tehran, Iran. Three sizes of particles including PM10, PM2.5 and PM1.0 were measured in 13 classrooms within this schools during winter (January, February and March) 2009. A laserbased portable aerosol spectrometer Model Grimm-1.108, was used for the continuous measurement of particles. The average indoor concentration of PM10, PM2.5 and PM1.0 in studied schools were 274 μg/m3, 42 μg/m3 and 19 μg/m3 respectively; and average outdoor concentrations of PM10, PM2.5 and PM1.0 were evaluated to be 22 μg/m3, 38 μg/m3 and 140 μg/m3 respectively.
Abstract: The paper investigates the feasibility of constructing a software multi-agent based monitoring and classification system and utilizing it to provide an automated and accurate classification of end users developing applications in the spreadsheet domain. The agents function autonomously to provide continuous and periodic monitoring of excels spreadsheet workbooks. Resulting in, the development of the MultiAgent classification System (MACS) that is in compliance with the specifications of the Foundation for Intelligent Physical Agents (FIPA). However, different technologies have been brought together to build MACS. The strength of the system is the integration of the agent technology with the FIPA specifications together with other technologies that are Windows Communication Foundation (WCF) services, Service Oriented Architecture (SOA), and Oracle Data Mining (ODM). The Microsoft's .NET widows service based agents were utilized to develop the monitoring agents of MACS, the .NET WCF services together with SOA approach allowed the distribution and communication between agents over the WWW that is in order to satisfy the monitoring and classification of the multiple developer aspect. ODM was used to automate the classification phase of MACS.
Abstract: This paper aims to present knowledge management for solving economic problem and poverty in Thai community. A community in Thailand is studied as a case study for master plan or social and economic plan which derived form the research people conducted by themselves in their community. The result shows that community uses knowledge management in recording income and expense, analyzing their consumption, and then systematic planning of the production, distribution and consumption in the community. Besides, community enterprises, that people create as the by-products of master plan, can facilitate diverse economic activities which are able to reduce economic problem and poverty. The knowledge that people gain from solving their problem through building community enterprises are both tacit and explicit knowledge. Four styles of knowledge conversion: socialization,externalization, combination and internalization, are used. Besides, knowledge sharing inside the organization, between organizations and its environment are found. Keywordsknowledge management, community enterprise, Thailand.
Abstract: In built-up structures, one of the effective ways of
dissipating unwanted vibration is to exploit the occurrence of slip at
the interfaces of structural laminates. The present work focuses on
the dynamic analysis of welded structures. A mathematical
formulation has been developed for the mechanism of slip damping
in layered and welded mild steel beams with unequal thickness
subjected to both periodic and non-periodic forces. It is observed that
a number of vital parameters such as; thickness ratio, pressure
distribution characteristics, relative slip and kinematic co-efficient of
friction at the interfaces, nature of exciting forces, length and
thickness of the beam specimen govern the damping characteristics of
these structures. Experimental verification has been carried out to
validate the analysis and study the effect of these parameters. The
developed damping model for the structure is found to be in fairly
good agreement with the measured data. Finally, the results of the
analysis are discussed and rationalized.
Abstract: This paper focuses on reducing the power consumption
of wireless sensor networks. Therefore, a communication protocol
named LEACH (Low-Energy Adaptive Clustering Hierarchy) is modified.
We extend LEACHs stochastic cluster-head selection algorithm
by a modifying the probability of each node to become cluster-head
based on its required energy to transmit to the sink. We present
an efficient energy aware routing algorithm for the wireless sensor
networks. Our contribution consists in rotation selection of clusterheads
considering the remoteness of the nodes to the sink, and then,
the network nodes residual energy. This choice allows a best distribution
of the transmission energy in the network. The cluster-heads
selection algorithm is completely decentralized. Simulation results
show that the energy is significantly reduced compared with the
previous clustering based routing algorithm for the sensor networks.
Abstract: Dilated cardiomyopathy (DCM) is a severe
cardiovascular disorder characterized by progressive systolic
dysfunction due to cardiac chamber dilatation and inefficient
myocardial contractility often leading to chronic heart failure.
Recently, a genome-wide association studies (GWASs) on DCM
indicate that the ZBTB17 gene rs10927875 single nucleotide
polymorphism is associated with DCM. The aim of the study was to
identify the distribution of ZBTB17 gene rs10927875 polymorphism
in 50 Slovak patients with DCM and 80 healthy control subjects
using the Custom Taqman®SNP Genotyping assays. Risk factors
detected at baseline in each group included age, sex, body mass
index, smoking status, diabetes and blood pressure. The mean age of
patients with DCM was 52.9±6.3 years; the mean age of individuals
in control group was 50.3±8.9 years. The distribution of investigated
genotypes of rs10927875 polymorphism within ZBTB17 gene in the
cohort of Slovak patients with DCM was as follows: CC (38.8%), CT
(55.1%), TT (6.1%), in controls: CC (43.8%), CT (51.2%), TT
(5.0%). The risk allele T was more common among the patients with
dilated cardiomyopathy than in normal controls (33.7% versus
30.6%). The differences in genotype or allele frequencies of ZBTB17
gene rs10927875 polymorphism were not statistically significant
(p=0.6908; p=0.6098). The results of this study suggest that ZBTB17
gene rs10927875 polymorphism may be a risk factor for
susceptibility to DCM in Slovak patients with DCM. Studies of
numerous files and additional functional investigations are needed to
fully understand the roles of genetic associations.
Abstract: Non-uniform current distribution in polymer
electrolyte membrane fuel cells results in local over-heating,
accelerated ageing, and lower power output than expected. This
issue is very critical when fuel cell experiences water flooding. In
this work, the performance of a PEM fuel cell is investigated under
cathode flooding conditions. Two-dimensional partially flooded
GDL models based on the conservation laws and electrochemical
relations are proposed to study local current density distributions
along flow fields over a wide range of cell operating conditions.
The model results show a direct association between cathode inlet
humidity increases and that of average current density but the
system becomes more sensitive to flooding. The anode inlet
relative humidity shows a similar effect. Operating the cell at
higher temperatures would lead to higher average current densities
and the chance of system being flooded is reduced. In addition,
higher cathode stoichiometries prevent system flooding but the
average current density remains almost constant. The higher anode
stoichiometry leads to higher average current density and higher
sensitivity to cathode flooding.
Abstract: Recently, Northeast Asia has become one of the three
largest trade areas, covering approximately 30% of the total trade
volume of the world. However, the distribution facilities are saturated
due to the increase in the transportation volume within the area and
with the European countries. In order to accommodate the increase of
the transportation volume, the transportation networking with the
major countries in Northeast Asia and Europe is absolutely necessary.
The Eurasian Logistics Network will develop into an international
passenger transportation network covering the Northeast Asian region
and an international freight transportation network connecting across
Eurasia Continent. This paper surveys the changes and trend of the
distribution network in the Eurasian Region according to the political,
economic and environmental changes of the region, analyses the
distribution network according to the changes in the transportation
policies of the related countries, and provides the direction of the
development of composite transportation on the basis of the present
conditions of transportation means. The transportation means optimal
for the efficiency of transportation system are suggested to be train
ferries, sea & rail or sea & rail & sea. It is suggested to develop
diversified composite transportation means and routes within the
boundary of international cooperation system.
Abstract: This paper reports a new and accurate method for load-flow solution of radial distribution networks with minimum data preparation. The node and branch numbering need not to be sequential like other available methods. The proposed method does not need sending-node, receiving-node and branch numbers if these are sequential. The proposed method uses the simple equation to compute the voltage magnitude and has the capability to handle composite load modelling. The proposed method uses the set of nodes of feeder, lateral(s) and sub lateral(s). The effectiveness of the proposed method is compared with other methods using two examples. The detailed load-flow results for different kind of load-modellings are also presented.
Abstract: This paper presents a numerical approach for the static
and dynamic analysis of hydrodynamic radial journal bearings. In the
first part, the effect of shaft and housing deformability on pressure
distribution within oil film is investigated. An iterative algorithm that
couples Reynolds equation with a plane finite elements (FE)
structural model is solved. Viscosity-to-pressure dependency (Vogel-
Barus equation) is also included. The deformed lubrication gap and
the overall stress state are obtained. Numerical results are presented
with reference to a typical journal bearing configuration at two
different inlet oil temperatures. Obtained results show the great
influence of bearing components structural deformation on oil
pressure distribution, compared with results for ideally rigid
components. In the second part, a numerical approach based on
perturbation method is used to compute stiffness and damping
matrices, which characterize the journal bearing dynamic behavior.
Abstract: The major challenge faced by wireless sensor networks is security. Because of dynamic and collaborative nature of sensor networks the connected sensor devices makes the network unusable. To solve this issue, a trust model is required to find malicious, selfish and compromised insiders by evaluating trust worthiness sensors from the network. It supports the decision making processes in wireless sensor networks such as pre key-distribution, cluster head selection, data aggregation, routing and self reconfiguration of sensor nodes. This paper discussed the kinds of trust model, trust metrics used to address attacks by monitoring certain behavior of network. It describes the major design issues and their countermeasures of building trust model. It also discusses existing trust models used in various decision making process of wireless sensor networks.
Abstract: The double exponential model (DEM), or Laplace
distribution, is used in various disciplines. However, there are issues
related to the construction of confidence intervals (CI), when using
the distribution.In this paper, the properties of DEM are considered
with intention of constructing CI based on simulated data. The
analysis of pivotal equations for the models here in comparisons with
pivotal equations for normal distribution are performed, and the
results obtained from simulation data are presented.
Abstract: Background: Regular physical activity contributes
positively to physical and psychological health. In the present study,
the stages of change of physical activity and the total physical
Aims: The aim of this study was to investigate the proportion of
adolescent girls in each stages of change and the causative factors
associated with physical activity such as the related social support
and self efficacy in a sample of the high school students.
Methods: In this study, Social Cognitive Theory (SCT) and the
Transtheorical Model (TTM) guided instrument development. The
data regarding the demographics, psychosocial determinants of
physical activity, stage of change and physical activity was gathered
by questionnaires. Several measures of psychosocial determinants of
physical activity were translated from English into Persian using the
back-translation technique. These translated measures were
administered to 512 ninth and tenth-grade Iranian high school
students for factor analysis.
Results: The distribution of the stage of change for physical activity
was as follow: 18/5% in precontemplation, 23.4% in contemplation,
38.2% in preparation, 4.6% in action and 15.3% in maintenance.
They were in 80.1% pre-adoption stages (precontemplation stage,
contemplation stage and preparation stage) and 19.9% post-adoption
stages (action stage and maintenance stage) of physical activity.
There was a significant relate between age and physical activity in
adolescent girls (age-related decline of physical activity) p
Abstract: The selection of appropriate requirements for product
releases can make a big difference in a product success. The selection
of requirements is done by different requirements prioritization
techniques. These techniques are based on pre-defined and
systematic steps to calculate the requirements relative weight.
Prioritization is complicated by new development settings, shifting
from traditional co-located development to geographically distributed
development. Stakeholders, connected to a project, are distributed all
over the world. These geographically distributions of stakeholders
make it hard to prioritize requirements as each stakeholder have their
own perception and expectations of the requirements in a software
project. This paper discusses limitations of the Analytical Hierarchy
Process with respect to geographically distributed stakeholders-
(GDS) prioritization of requirements. This paper also provides a
solution, in the form of a modified AHP, in order to prioritize
requirements for GDS. We will conduct two experiments in this
paper and will analyze the results in order to discuss AHP limitations
with respect to GDS. The modified AHP variant is also validated in
this paper.
Abstract: A kind of singularly perturbed boundary value problems is under consideration. In order to obtain its approximation, simple upwind difference discretization is applied. We use a moving mesh iterative algorithm based on equi-distributing of the arc-length function of the current computed piecewise linear solution. First, a maximum norm a posteriori error estimate on an arbitrary mesh is derived using a different method from the one carried out by Chen [Advances in Computational Mathematics, 24(1-4) (2006), 197-212.]. Then, basing on the properties of discrete Green-s function and the presented posteriori error estimate, we theoretically prove that the discrete solutions computed by the algorithm are first-order uniformly convergent with respect to the perturbation parameter ε.
Abstract: In this study, numerical simulations on laminar flow in
sinusoidal wavy shaped tubes were conducted for mean Reynolds
number of 250, which is in the range of physiological flow-rate and
investigated flow structures, pressure distribution and particle
trajectories both in steady and periodic inflow conditions. For
extensive comparisons, various wave lengths and amplitudes of sine
function for geometry of tube models were employed. The results
showed that small amplitude secondary curvature has significant
influence on the nature of flow patterns and particle mixing
mechanism. This implies that characterizing accurate geometry is
essential in accurate predicting of in vivo hemodynamics and may
motivate further study on any possibility of reflection of secondary
flow on vascular remodeling and pathophysiology.
Abstract: Droplet size distributions in the cold spray of a fuel
are important in observed combustion behavior. Specification of
droplet size and velocity distributions in the immediate downstream
of injectors is also essential as boundary conditions for advanced
computational fluid dynamics (CFD) and two-phase spray transport
calculations. This paper describes the development of a new model to
be incorporated into maximum entropy principle (MEP) formalism
for prediction of droplet size distribution in droplet formation region.
The MEP approach can predict the most likely droplet size and
velocity distributions under a set of constraints expressing the
available information related to the distribution.
In this article, by considering the mechanisms of turbulence
generation inside the nozzle and wave growth on jet surface, it is
attempted to provide a logical framework coupling the flow inside the
nozzle to the resulting atomization process. The purpose of this paper
is to describe the formulation of this new model and to incorporate it
into the maximum entropy principle (MEP) by coupling sub-models
together using source terms of momentum and energy. Comparison
between the model prediction and experimental data for a gas turbine
swirling nozzle and an annular spray indicate good agreement
between model and experiment.
Abstract: SeqWord Gene Island Sniffer, a new program for
the identification of mobile genetic elements in sequences of bacterial chromosomes is presented. This program is based on the
analysis of oligonucleotide usage variations in DNA sequences. 3,518 mobile genetic elements were identified in 637 bacterial
genomes and further analyzed by sequence similarity and the
functionality of encoded proteins. The results of this study are stored in an open database http://anjie.bi.up.ac.za/geidb/geidbhome.
php). The developed computer program and the database provide the information valuable for further investigation of the
distribution of mobile genetic elements and virulence factors among bacteria. The program is available for download at www.bi.up.ac.za/SeqWord/sniffer/index.html.