Abstract: Nonlinear finite element method and Serendipity eight
nodes element are used for determining of ground surface settlement
due to tunneling. Linear element with elastic behavior is used for
modeling of lining. Modified Generalized plasticity model with nonassociated
flow rule is applied for analysis of a tunnel in Sao Paulo –
Brazil. The tunnel had analyzed by Lades- model with 16 parameters.
In this work modified Generalized Plasticity is used with 10
parameters, also Mohr-Coulomb model is used to analysis the tunnel.
The results show good agreement with observed results of field data
by modified Generalized Plasticity model than other models. The
obtained result by Mohr-Coulomb model shows less settlement than
other model due to excavation.
Abstract: Multi criteria decision analysis (MDCA) covers both
data and experience. It is very common to solve the problems with
many parameters and uncertainties. GIS supported solutions improve
and speed up the decision process. Weighted grading as a MDCA
method is employed for solving the geotechnical problems. In this
study, geotechnical parameters namely soil type; SPT (N) blow
number, shear wave velocity (Vs) and depth of underground water
level (DUWL) have been engaged in MDCA and GIS. In terms of
geotechnical aspects, the settlement suitability of the municipal area
was analyzed by the method. MDCA results were compatible with
the geotechnical observations and experience. The method can be
employed in geotechnical oriented microzoning studies if the criteria
are well evaluated.
Abstract: The peel of dragon fruit is a byproduct left over after consuming. Normally, the use of plants as antioxidant source must be dried before further process. Therefore, the aim of this study is interesting to dry the peel by heat pump dryer (45 ºC) and fluidized bed dryer (110 º C) compared with the sun drying method. The sample with initial moisture content of about 85-91% wet basis was dried down to about 10% wet basis where it took 620 and 25 min for heat pump dryer and fluidized bed dryer, respectively. However, the sun drying took about 900 min to dry the peel. After that, sample was evaluated antioxidant activity, -carotene and betalains contents. The results found that the antioxidant activity and betalains contents of dried peel obtained from heat pump and fluidized bed dryings were significantly higher than that sun drying (p 0.05). Moreover, the drying by heat pump provided the highest -carotene content.
Abstract: The paper presents the design of a mini-UAV attitude
controller using the backstepping method. Starting from the nonlinear
dynamic equations of the mini-UAV, by using the backstepping
method, the author of this paper obtained the expressions of the
elevator, rudder and aileron deflections, which stabilize the UAV, at
each moment, to the desired values of the attitude angles. The attitude
controller controls the attitude angles, the angular rates, the angular
accelerations and other variables that describe the UAV longitudinal
and lateral motions. To design the nonlinear controller, by using the
backstepping technique, the nonlinear equations and the Lyapunov
analysis have been directly used. The designed controller has been
implemented in Matlab/Simulink environment and its effectiveness
has been tested with a campaign of numerical simulations using data
from the UAV flight tests. The obtained results are very good and
they are better than the ones found in previous works.
Abstract: In order to survive in a rapidly changing business environment, Malaysian business firms must improve their own business practices and procedures. This paper describes the impact of Critical Success Factors (CSFs) during the Enterprise Resource Planning (ERP) system implementations using the responses from 151 organizations that completed or are in the process of completing an ERP implementation and identifying the key benefits of ERP implementation in the firm. The importance of these factors was investigated within Malaysian companies using questionnaire survey method. Our results provide advice to management on how best to utilize their limited resources to choose those CSFs that are most likely to have an impact upon the implementation of the ERP system.
Abstract: Cavitation, usually known as a destructive
phenomenon, involves turbulent unsteady two-phase flow. Having
such features, cavitating flows have been turned to a challenging
topic in numerical studies and many researches are being done for
better understanding of bubbly flows and proposing solutions to
reduce its consequent destructive effects. Aeration may be regarded
as an effective protection against cavitation erosion in many
hydraulic structures, like gated tunnels. The paper concerns
numerical simulation of flow in discharge gated tunnel of a dam
using ing RNG k -ε model coupled with the volume of fluid (VOF)
method and the zone which is susceptible of cavitation inception in
the tunnel is predicted. In the second step, a vent is considered in the
mentioned zone for aeration and the numerical simulation is done
again to study the effects of aeration. The results show that aeration
is an impressively useful method to exclude cavitation in mentioned
tunnels.
Abstract: This paper investigates the effect of replacing
crankshaft with cam on the indicated torque during compression and
power strokes in internal combustion engines. A Cycloidal cam
profile was used in Revetec engine to calculate and compare the
torque to a conventional engine, using a computational method.
Firstly, the cylinder pressure was calculated using Ferguson equation,
and then the torque calculated depending on cylinder pressure values
in every crank angle. the results showed that by using Cycloidal cam
profile in Revetec engine the torque can increased by 14% compared
with conventional engines, which means an increase in engine
efficiency.
Abstract: Antibacterial activity of Plumeria alba (Frangipani)
petals methanolic extracts were evaluated against Escherichia coli,
Proteus vulgaris,Staphylococcus aureus, Klebsiella pneumoniae,
Pseudomonas aeruginosa, Staphylococcus saprophyticus,
Enterococcus faecalis and Serratia marcescens by using disk
diffusion method. Concentration extracts (80 %) showed the highest
inhibition zone towards Escherichia coli (14.3 mm). Frangipani
extract also showed high antibacterial activity against
Staphylococcus saprophyticus, Proteus vulgaris and Serratia
marcescens, but not more than the zones of the positive control used.
Comparison between two broad specrum antibiotics to frangipani
extracts showed that the 80 % concentration extracts produce the
same zone of inhibition as Streptomycin. Frangipani extracts showed
no bacterial activity towards Klebsiella pneumoniae, Pseudomonas
aeruginosa and Enterococcus faecalis. There are differences in the
sensitivity of different bacteria to frangipani extracts, suggesting that
frangipani-s potency varies between these bacteria. The present
results indicate that frangipani showed significant antibacterial
activity especially to Escherichia coli.
Abstract: At present, the tendency to implement the conditionbased
maintenance (CBM), which allows the optimization of the
expenses for equipment monitoring, is more and more evident; also,
the transformer substations with remote monitoring are increasingly
used. This paper reviews all the advantages of the on-line monitoring
and presents an equipment for on-line monitoring of bushings, which
is the own contribution of specialists who are the authors of this
paper. The paper presents a study of the temperature field, using the
finite element method. For carrying out this study, the 3D modelling
of the above mentioned bushing was performed. The analysis study is
done taking into account the extreme thermal stresses, focusing at the
level of the first cooling wing section of the ceramic insulator. This
fact enables to justify the tanδ variation in time, depending on the
transformer loading and the environmental conditions. With a view
to reducing the variation of dielectric losses in bushing insulation, the
use of ferrofuids instead of mineral oils is proposed.
Abstract: A transient heat transfer mathematical model for the
prediction of temperature distribution in the car body during primer
baking has been developed by considering the thermal radiation and
convection in the furnace chamber and transient heat conduction
governing equations in the car framework. The car cockpit is
considered like a structure with six flat plates, four vertical plates
representing the car doors and the rear and front panels. The other
two flat plates are the car roof and floor. The transient heat
conduction in each flat plate is modeled by the lumped capacitance
method. Comparison with the experimental data shows that the heat
transfer model works well for the prediction of thermal behavior of
the car body in the curing furnace, with deviations below 5%.
Abstract: A method for solving linear and non-linear Goursat
problem is given by using the two-dimensional differential transform
method. The approximate solution of this problem is calculated in
the form of a series with easily computable terms and also the exact
solutions can be achieved by the known forms of the series solutions.
The method can easily be applied to many linear and non-linear
problems and is capable of reducing the size of computational work.
Several examples are given to demonstrate the reliability and the
performance of the presented method.
Abstract: Stress analysis of functionally graded composite plates
composed of ceramic, functionally graded material and metal layers is
investigated using 3-D finite element method. In FGM layer, material
properties are assumed to be varied continuously in the thickness
direction according to a simple power law distribution in terms of the
volume fraction of a ceramic and metal. The 3-D finite element model
is adopted by using an 18-node solid element to analyze more
accurately the variation of material properties in the thickness
direction. Numerical results are compared for three types of materials.
In the analysis, the tensile and the compressive stresses are
summarized for various FGM thickness ratios, volume fraction
distributions, geometric parameters and mechanical loads.
Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: We employ the idea of Hirota-s bilinear method, to obtain some new exact soliton solutions for high nonlinear form of (2+1)-dimensional potential Kadomtsev-Petviashvili equation. Multiple singular soliton solutions were obtained by this method. Moreover, multiple singular soliton solutions were also derived.
Abstract: In a wind power generator using doubly fed induction
generator (DFIG), the three-phase pulse width modulation (PWM)
voltage source converter (VSC) is used as grid side converter (GSC)
and rotor side converter (RSC). The standard linear control laws
proposed for GSC provides not only instablity against comparatively
large-signal disturbances, but also the problem of stability due to
uncertainty of load and variations in parameters. In this paper, a
nonlinear controller is designed for grid side converter (GSC) of a
DFIG for wind power application. The nonlinear controller is
designed based on the input-output feedback linearization control
method. The resulting closed-loop system ensures a sufficient
stability region, make robust to variations in circuit parameters and
also exhibits good transient response. Computer simulations and
experimental results are presented to confirm the effectiveness of the
proposed control strategy.
Abstract: Due to the increasing penetration of wind energy, it is
necessary to possess design tools that are able to simulate the impact
of these installations in utility grids. In order to provide a net
contribution to this issue a detailed wind park model has been
developed and is briefly presented. However, the computational costs
associated with the performance of such a detailed model in
describing the behavior of a wind park composed by a considerable
number of units may render its practical application very difficult. To
overcome this problem integral manifolds theory has been applied to
reduce the order of the detailed wind park model, and therefore
create the conditions for the development of a dynamic equivalent
which is able to retain the relevant dynamics with respect to the
existing a.c. system. In this paper integral manifold method has been
introduced for order reduction. Simulation results of the proposed
method represents that integral manifold method results fit the
detailed model results with a higher precision than singular
perturbation method.
Abstract: This paper presents an approach which is based on the
use of supervised feed forward neural network, namely multilayer
perceptron (MLP) neural network and finite element method (FEM)
to solve the inverse problem of parameters identification. The
approach is used to identify unknown parameters of ferromagnetic
materials. The methodology used in this study consists in the
simulation of a large number of parameters in a material under test,
using the finite element method (FEM). Both variations in relative
magnetic permeability and electrical conductivity of the material
under test are considered. Then, the obtained results are used to
generate a set of vectors for the training of MLP neural network.
Finally, the obtained neural network is used to evaluate a group of
new materials, simulated by the FEM, but not belonging to the
original dataset. Noisy data, added to the probe measurements is used
to enhance the robustness of the method. The reached results
demonstrate the efficiency of the proposed approach, and encourage
future works on this subject.
Abstract: This paper proposes a new method for image searches and image indexing in databases with a color temperature histogram. The color temperature histogram can be used for performance improvement of content–based image retrieval by using a combination of color temperature and histogram. The color temperature histogram can be represented by a range of 46 colors. That is more than the color histogram and the dominant color temperature. Moreover, with our method the colors that have the same color temperature can be separated while the dominant color temperature can not. The results showed that the color temperature histogram retrieved an accurate image more often than the dominant color temperature method or color histogram method. This also took less time so the color temperature can be used for indexing and searching for images.
Abstract: The k-nearest neighbors (knn) is a simple but effective method of classification. In this paper we present an extended version of this technique for chemical compounds used in High Throughput Screening, where the distances of the nearest neighbors can be taken into account. Our algorithm uses kernel weight functions as guidance for the process of defining activity in screening data. Proposed kernel weight function aims to combine properties of graphical structure and molecule descriptors of screening compounds. We apply the modified knn method on several experimental data from biological screens. The experimental results confirm the effectiveness of the proposed method.
Abstract: We present in this paper a new approach for specific JPEG steganalysis and propose studying statistics of the compressed DCT coefficients. Traditionally, steganographic algorithms try to preserve statistics of the DCT and of the spatial domain, but they cannot preserve both and also control the alteration of the compressed data. We have noticed a deviation of the entropy of the compressed data after a first embedding. This deviation is greater when the image is a cover medium than when the image is a stego image. To observe this deviation, we pointed out new statistic features and combined them with the Multiple Embedding Method. This approach is motivated by the Avalanche Criterion of the JPEG lossless compression step. This criterion makes possible the design of detectors whose detection rates are independent of the payload. Finally, we designed a Fisher discriminant based classifier for well known steganographic algorithms, Outguess, F5 and Hide and Seek. The experiemental results we obtained show the efficiency of our classifier for these algorithms. Moreover, it is also designed to work with low embedding rates (< 10-5) and according to the avalanche criterion of RLE and Huffman compression step, its efficiency is independent of the quantity of hidden information.