Abstract: Octree compression techniques have been used
for several years for compressing large three dimensional data
sets into homogeneous regions. This compression technique
is ideally suited to datasets which have similar values in
clusters. Oil engineers represent reservoirs as a three dimensional
grid where hydrocarbons occur naturally in clusters. This
research looks at the efficiency of storing these grids using
octree compression techniques where grid cells are broken
into active and inactive regions. Initial experiments yielded
high compression ratios as only active leaf nodes and their
ancestor, header nodes are stored as a bitstream to file on
disk. Savings in computational time and memory were possible
at decompression, as only active leaf nodes are sent to the
graphics card eliminating the need of reconstructing the original
matrix. This results in a more compact vertex table, which can
be loaded into the graphics card quicker and generating shorter
refresh delay times.
Abstract: In this study, effects of premixed and equivalence
ratios on CO and HC emissions of a dual fuel HCCI engine are
investigated. Tests were conducted on a single-cylinder engine with
compression ratio of 17.5. Premixed gasoline is provided by a
carburetor connected to intake manifold and equipped with a screw
to adjust premixed air-fuel ratio, and diesel fuel is injected directly
into the cylinder through an injector at pressure of 250 bars. A heater
placed at inlet manifold is used to control the intake charge
temperature. Optimal intake charge temperature results in better
HCCI combustion due to formation of a homogeneous mixture,
therefore, all tests were carried out over the optimum intake
temperature of 110-115 ºC. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge and plays an important
role in HCCI combustion phasing. Experiments indicated 35 BTDC
as the optimum injection timing. Varying the coolant temperature in
a range of 40 to 70 ºC, better HCCI combustion was achieved at 50
ºC. Therefore, coolant temperature was maintained 50 ºC during all
tests. Simultaneous investigation of effective parameters on HCCI
combustion was conducted to determine optimum parameters
resulting in fast transition to HCCI combustion. One of the
advantages of the method studied in this study is feasibility of easy
and fast transition of typical diesel engine to a dual fuel HCCI
engine. Results show that increasing premixed ratio, while keeping
EGR rate constant, increases unburned hydrocarbon (UHC)
emissions due to quenching phenomena and trapping of premixed
fuel in crevices, but CO emission decreases due to increase in CO to
CO2 reactions.
Abstract: This paper presents a system for discovering
association rules from collections of unstructured documents called
EART (Extract Association Rules from Text). The EART system
treats texts only not images or figures. EART discovers association
rules amongst keywords labeling the collection of textual documents.
The main characteristic of EART is that the system integrates XML
technology (to transform unstructured documents into structured
documents) with Information Retrieval scheme (TF-IDF) and Data
Mining technique for association rules extraction. EART depends on
word feature to extract association rules. It consists of four phases:
structure phase, index phase, text mining phase and visualization
phase. Our work depends on the analysis of the keywords in the
extracted association rules through the co-occurrence of the keywords
in one sentence in the original text and the existing of the keywords
in one sentence without co-occurrence. Experiments applied on a
collection of scientific documents selected from MEDLINE that are
related to the outbreak of H5N1 avian influenza virus.
Abstract: Bio-chips are used for experiments on genes and
contain various information such as genes, samples and so on. The
two-dimensional bio-chips, in which one axis represent genes and the
other represent samples, are widely being used these days. Instead of
experimenting with real genes which cost lots of money and much
time to get the results, bio-chips are being used for biological
experiments. And extracting data from the bio-chips with high
accuracy and finding out the patterns or useful information from such
data is very important. Bio-chip analysis systems extract data from
various kinds of bio-chips and mine the data in order to get useful
information. One of the commonly used methods to mine the data is
classification. The algorithm that is used to classify the data can be
various depending on the data types or number characteristics and so
on. Considering that bio-chip data is extremely large, an algorithm that
imitates the ecosystem such as the ant algorithm is suitable to use as an
algorithm for classification. This paper focuses on finding the
classification rules from the bio-chip data using the Ant Colony
algorithm which imitates the ecosystem. The developed system takes
in consideration the accuracy of the discovered rules when it applies it
to the bio-chip data in order to predict the classes.
Abstract: The main objective of this paper is to determine the
isolated effect of silica fume on tensile, compressive and flexure strengths on high strength lightweight concrete. Many experiments
were carried out by replacing cement with different percentages of silica fume at different constant water-binder ratio keeping other mix
design variables constant. The silica fume was replaced by 0%, 5%,
10%, 15%, 20% and 25% for a water-binder ratios ranging from 0.26
to 0.42. For all mixes, split tensile, compressive and flexure strengths
were determined at 28 days. The results showed that the tensile, compressive and flexure strengths increased with silica fume incorporation but the optimum replacement percentage is not
constant because it depends on the water–cementitious material (w/cm) ratio of the mix. Based on the results, a relationship between
split tensile, compressive and flexure strengths of silica fume concrete was developed using statistical methods.
Abstract: A Web-based learning tool, the Learn IN Context
(LINC) system, designed and being used in some institution-s
courses in mixed-mode learning, is presented in this paper. This
mode combines face-to-face and distance approaches to education.
LINC can achieve both collaborative and competitive learning. In
order to provide both learners and tutors with a more natural way to
interact with e-learning applications, a conversational interface has
been included in LINC. Hence, the components and essential features
of LINC+, the voice enhanced version of LINC, are described. We
report evaluation experiments of LINC/LINC+ in a real use context
of a computer programming course taught at the Université de
Moncton (Canada). The findings show that when the learning
material is delivered in the form of a collaborative and voice-enabled
presentation, the majority of learners seem to be satisfied with this
new media, and confirm that it does not negatively affect their
cognitive load.
Abstract: Explosive welding is a process which uses explosive
detonation to move the flyer plate material into the base material to
produce a solid state joint. Experimental tests have been carried out
by other researchers; have been considered to explosively welded
aluminium 7039 and steel 4340 tubes in one step. The tests have been
done using various stand-off distances and explosive ratios. Various
interface geometries have been obtained from these experiments. In
this paper, all the experiments carried out were simulated using the
finite element method. The flyer plate and collision velocities
obtained from the analysis were validated by the pin-measurement
experiments. The numerical results showed that very high localized
plastic deformation produced at the bond interface. The
Ls_dyna_971 FEM has been used for all simulation process.
Abstract: In the present work, a study has been made on the combination of the electrical discharge machining (EDM) with ultrasonic vibrations to improve the machining efficiency. In experiments the graphite used as tool electrode and material of workpiece was AISIH13 tool steel. The parameters such as discharge peak current and pulse duration were changed to explore their effect on the material removal rate (MRR), relative tool wear ratio (TWR) and surface roughness. From the experimental result it can be seen that ultrasonic vibration of the workpiece can significantly reduces the inactive pulses and improves the stability of process. It was found that ultrasonic assisted EDM (US-EDM) is effective in attaining a high material removal rate (MRR) in finishing regime.
Abstract: It has been established that microRNAs (miRNAs) play
an important role in gene expression by post-transcriptional regulation
of messengerRNAs (mRNAs). However, the precise relationships
between microRNAs and their target genes in sense of numbers,
types and biological relevance remain largely unclear. Dissecting the
miRNA-target relationships will render more insights for miRNA
targets identification and validation therefore promote the understanding
of miRNA function. In miRBase, miRanda is the key
algorithm used for target prediction for Zebrafish. This algorithm
is high-throughput but brings lots of false positives (noise). Since
validation of a large scale of targets through laboratory experiments
is very time consuming, several computational methods for miRNA
targets validation should be developed. In this paper, we present an
integrative method to investigate several aspects of the relationships
between miRNAs and their targets with the final purpose of extracting
high confident targets from miRanda predicted targets pool. This is
achieved by using the techniques ranging from statistical tests to
clustering and association rules. Our research focuses on Zebrafish.
It was found that validated targets do not necessarily associate with
the highest sequence matching. Besides, for some miRNA families,
the frequency of their predicted targets is significantly higher in the
genomic region nearby their own physical location. Finally, in a case
study of dre-miR-10 and dre-miR-196, it was found that the predicted
target genes hoxd13a, hoxd11a, hoxd10a and hoxc4a of dre-miR-
10 while hoxa9a, hoxc8a and hoxa13a of dre-miR-196 have similar
characteristics as validated target genes and therefore represent high
confidence target candidates.
Abstract: Load forecasting has become in recent years one of the major areas of research in electrical engineering. Most traditional forecasting models and artificial intelligence neural network techniques have been tried out in this task. Artificial neural networks (ANN) have lately received much attention, and a great number of papers have reported successful experiments and practical tests. This article presents the development of an ANN-based short-term load forecasting model with improved generalization technique for the Regional Power Control Center of Saudi Electricity Company, Western Operation Area (SEC-WOA). The proposed ANN is trained with weather-related data and historical electric load-related data using the data from the calendar years 2001, 2002, 2003, and 2004 for training. The model tested for one week at five different seasons, typically, winter, spring, summer, Ramadan and fall seasons, and the mean absolute average error for one hour-ahead load forecasting found 1.12%.
Abstract: Recent developments in storage technology and
networking architectures have made it possible for broad areas of applications to rely on data streams for quick response and accurate
decision making. Data streams are generated from events of real world so existence of associations, which are among the occurrence of these events in real world, among concepts of data streams is
logical. Extraction of these hidden associations can be useful for prediction of subsequent concepts in concept shifting data streams. In this paper we present a new method for learning association among
concepts of data stream and prediction of what the next concept will be. Knowing the next concept, an informed update of data model will be possible. The results of conducted experiments show that the proposed method is proper for classification of concept shifting data
streams.
Abstract: Abrasive waterjet cutting (AWJ) is a highly efficient
method for cutting almost any type of material. When holes shall be
cut the waterjet first needs to pierce the material.This paper presents a
vast experimental analysis of piercing parameters effect on piercing
time. Results from experimentation on feed rates, work piece
thicknesses, abrasive flow rates, standoff distances and water
pressure are also presented as well as studies on three methods for
dynamic piercing. It is shown that a large amount of time and
resources can be saved by choosing the piercing parameters in a
correct way. The large number of experiments puts demands on the
experimental setup. An automated experimental setup including
piercing detection is presented to enable large series of experiments
to be carried out efficiently.
Abstract: Ringing effect is one of the most annoying visual
artifacts in digital video. It is a significant factor of subjective quality
deterioration. However, there is a widely-accepted misunderstanding
of its cause. In this paper, we propose a reasonable interpretation of the
cause of ringing effect. Based on the interpretation, we suggest further
two methods to reduce ringing effect in DCT-based video coding. The
methods adaptively adjust quantizers according to video features. Our
experiments proved that the methods could efficiently improve
subjective quality with acceptable additional computing costs.
Abstract: Two seperate experiments by barley and alfalfa were
conducted to a 2×8 factorial completely randomised design, with four
replicates. Factors were inoculation (M) with Gomus mosseae or uninoculation
(M0) and seven levels of contaminants (Co, Cd, Pb and
combinations) plus an uncontaminated control treatment (C). Heavy
metals in plant tissues and soil were quantified by Inductively
Coupled Plasma Optical Emission Spectrometer (ICP-OES) (Variant-
Liberty 150AX Turbo). Phytoextraction coefficient of contaminants
calculated by concentration of heavy metals in the shoot (mgkg-1) /
concentration of heavy metals in soil (mgkg-1). In the barley, the
highest rate of phytoextraction coefficient of Pb, Cd and Co was in
M0Pb, M0PbCoCd and MCo, respectively (P
Abstract: This research evaluated and compared the thermodynamic performance of heat pump systems which can be run under two different modes as air to air and air to water by using only one compressor. To achieve this comparison an experimental performance study was made on a traditional vapor compressed heat pump system that can be run air to air mode and air to water mode by help of a valve. The experiments made under different thermal conditions. Thermodynamic performance of the systems are presented and compared with each other for different working conditions.
Abstract: Artemia is one of the most conspicuous invertebrates
associated with aquaculture. It can be considered as a model
organism, offering numerous advantages for comprehensive and
multidisciplinary studies using morphologic or molecular methods.
Since DNA extraction is an important step of any molecular
experiment, a new and a rapid method of DNA extraction from adult
Artemia was described in this study. Besides, the efficiency of this
technique was compared with two widely used alternative techniques,
namely Chelex® 100 resin and SDS-chloroform methods. Data
analysis revealed that the new method is the easiest and the most cost
effective method among the other methods which allows a quick and
efficient extraction of DNA from the adult animal.
Abstract: Eye localization is necessary for face recognition and
related application areas. Most of eye localization algorithms reported
so far still need to be improved about precision and computational
time for successful applications. In this paper, we propose an eye
location method based on multi-scale Gabor feature vectors, which is
more robust with respect to initial points. The eye localization based
on Gabor feature vectors first needs to constructs an Eye Model Bunch
for each eye (left or right eye) which consists of n Gabor jets and
average eye coordinates of each eyes obtained from n model face
images, and then tries to localize eyes in an incoming face image by
utilizing the fact that the true eye coordinates is most likely to be very
close to the position where the Gabor jet will have the best Gabor jet
similarity matching with a Gabor jet in the Eye Model Bunch. Similar
ideas have been already proposed in such as EBGM (Elastic Bunch
Graph Matching). However, the method used in EBGM is known to be
not robust with respect to initial values and may need extensive search
range for achieving the required performance, but extensive search
ranges will cause much more computational burden. In this paper, we
propose a multi-scale approach with a little increased computational
burden where one first tries to localize eyes based on Gabor feature
vectors in a coarse face image obtained from down sampling of the
original face image, and then localize eyes based on Gabor feature
vectors in the original resolution face image by using the eye
coordinates localized in the coarse scaled image as initial points.
Several experiments and comparisons with other eye localization
methods reported in the other papers show the efficiency of our
proposed method.
Abstract: Quantitative characterization of nonlinear directional
couplings between stochastic oscillators from data is considered. We
suggest coupling characteristics readily interpreted from a physical
viewpoint and their estimators. An expression for a statistical
significance level is derived analytically that allows reliable coupling
detection from a relatively short time series. Performance of the
technique is demonstrated in numerical experiments.
Abstract: The reduction of hexavalent chromium by scrap iron
was investigated in continuous system, using long-term column
experiments, for aqueous Cr(VI) solutions having low buffering
capacities, over the Cr(VI) concentration range of 5 – 40 mg/L. The
results showed that the initial Cr(VI) concentration significantly
affects the reduction capacity of scrap iron. Maximum reduction
capacity of scrap iron was observed at the beginning of the column
experiments; the lower the Cr(VI) concentration, the greater the
experiment duration with maximum scrap iron reduction capacity.
However, due to passivation of active surface, scrap iron reduction
capacity continuously decreased in time, especially after Cr(VI)
breakthrough. The experimental results showed that highest
reduction capacity recorded until Cr(VI) breakthrough was 22.8 mg
Cr(VI)/g scrap iron, at CI = 5 mg/L, and decreased with increasing
Cr(VI) concentration. In order to assure total reduction of greater
Cr(VI) concentrations for a longer period of time, either the mass of
scrap iron filling, or the hydraulic retention time should be increased.
Abstract: This paper presented the results of an experimental
investigation into the axial fatigue behavior of a 5086 aluminum
alloy which have several notch-aspect ratios a0/c0 and notch
thickness ratio a/t with semi-elliptical surface cracks. Tests were
conducted in la b air for stress levels of 50 % of their yield
strength. Experiments were carried out for various notch to
thickness ratios. Crack growth rates of test specimens both in
surface and depth directions were determined by using die
penetration method. Fuzzy Logic method was used to predict the
deep direction crack growth because the dept of the crack is
considerably difficult to measure.