Abstract: Thermal insulation materials based on natural fibers
represent a very promising area of materials based on natural easy
renewable row sources. These materials may be in terms of the
properties of most competing synthetic insulations, but show
somewhat higher moisture sensitivity and thermal insulation
properties are strongly influenced by the density and orientation of
fibers. The paper described the problem of hygrothermal behavior of
thermal insulation materials based on natural plant and animal fibers.
This is especially the dependence of the thermal properties of these
materials on the type of fiber, bulk density, temperature, moisture and
the fiber orientation.
Abstract: In the present work, detailed analysis on flow characteristics of a pair of immiscible liquids through horizontal pipeline is simulated by using ANSYS FLUENT 6.2. Moderately viscous oil and water (viscosity ratio = 107, density ratio = 0.89 and interfacial tension = 0.024 N/m) have been taken as system fluids for the study. Volume of Fluid (VOF) method has been employed by assuming unsteady flow, immiscible liquid pair, constant liquid properties, and co-axial flow. Meshing has been done using GAMBIT. Quadrilateral mesh type has been chosen to account for the surface tension effect more accurately. From the grid independent study, we have selected 47037 number of mesh elements for the entire geometry. Simulation successfully predicts slug, stratified wavy, stratified mixed and annular flow, except dispersion of oil in water, and dispersion of water in oil. Simulation results are validated with horizontal literature data and good conformity is observed. Subsequently, we have simulated the hydrodynamics (viz., velocity profile, area average pressure across a cross section and volume fraction profile along the radius) of stratified wavy and annular flow at different phase velocities. The simulation results show that in the annular flow, total pressure of the mixture decreases with increase in oil velocity due to the fact that pipe cross section is completely wetted with water. Simulated oil volume fraction shows maximum at the centre in core annular flow, whereas, in stratified flow, maximum value appears at upper side of the pipeline. These results are in accord with the actual flow configuration. Our findings could be useful in designing pipeline for transportation of crude oil.
Abstract: In this paper influence of packaging method (vacuum
and modified atmosphere packaging) on lipid oxidative stability and
sensory properties of odor and taste of the traditional sausage
Petrovská klobása were examined. These parameters were examined
during storage period (7 months). In the end of storage period,
vacuum packed sausage showed better oxidative stability. Propanal
content was significantly lower (P
Abstract: Al-Si-Mg-Ni(-Cu) alloys are widely used in the automotive industry. They have the advantage of low weight associated with low coefficient of thermal expansion and excellent mechanical properties – mainly at high temperatures. The corrosion resistance of these alloys in coastal area, particularly sea water, however is not yet known. In this investigation, electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization have been used to evaluate the corrosion resistance of Al-6Si-0.5Mg-2Ni (-2Cu) alloys in simulated sea water environments. The potentiodynamic polarization curves reveal that 2 wt% Cu content alloy (Alloy-2) is more prone to corrosion than the Cu free alloy (Alloy-1). But the EIS test results showed that corrosion resistance or charge transfer resistance (Rct) increases with the addition of Cu. Due to addition of Cu and thermal treatment, the magnitude of open circuit potential (OCP), corrosion potential (Ecorr) and pitting corrosion potential (Epit) of Al-6Si-0.5Mg-2Ni alloy in NaCl solution were shifted to the more noble direction.
Abstract: Amyloid aggregation of polypeptides is related to a
growing number of pathologic states known as amyloid disorders. In
recent years, blocking or reversing amyloid aggregation via the use of
small compounds are considered as two useful approaches in
hampering the development of these diseases. In this research, we
have compared the ability of several manganese-salen derivatives, as
synthetic compounds, and apigenin, as a natural flavonoid, to inhibit
of hen egg-white lysozyme (HEWL) aggregation, as an in vitro
model system.
Different spectroscopic analyses such as Thioflavin T (ThT) and
Anilinonaphthalene-8-sulfonic acid (ANS) fluorescence, Congo red
(CR) absorbance along with transmission electron microscopy were
used in this work to monitor the HEWL aggregation kinetic and
inhibition. Our results demonstrated that both type of compounds
were capable to prevent the formation of lysozyme amyloid
aggregation in vitro. In addition, our data indicated that synthetic
compounds had higher activity to inhibit of the β-sheet structures
relative to natural compound. Regarding the higher antioxidant
activities of the salen derivatives, it can be concluded that in addition
to aromatic rings of each of the compounds, the potent antioxidant
properties of salen derivatives contributes to lower lysozyme fibril
accumulation.
Abstract: This research aimed to produce offset printing inks from Samut Songkram’s coconut oil and to test properties of the printing inks comparing with commercial offset printing inks. One of the ingredients in the process of mixing varnish is coconut oil – used to produce black offset printing inks which were the subject of testing issues in order to compare with commercial offset printing inks. Based on the results of research, the best formula for mixing varnish was 50% of coconut oil, 36% of phenolic resin, and 14% of solvent oil. At the same time, the best formula in producing black offset inks was mixing varnish with 20% of coconut oil 20%. Consequently, the result of testing of properties of coconut oil based solvent offset printing inks regarding viscosity, tack and ink flow, showed that offset printing inks with oil based solvent had the properties less than commercial offset printing ink. Additionally, the result of testing also indicate that the rate of properties in aspects of ink spread and setting time of coconut oil based solvent offset printing were higher than that of commercial offset printing inks.
Abstract: This paper considers the bent and hyper-bent properties
of a class of Boolean functions. For one case, we present a detailed
description for them to be hyper-bent functions, and give a necessary
condition for them to be bent functions for another case.
Abstract: Poly(lactic acid) (PLA) is a biodegradable polymer
which has good mechanical properties, however, its brittleness limits
its usage especially in packaging materials. Therefore, in this work,
PLA based polyurethane films were prepared by synthesizing with
different types of isocyanates; methylene diisocyanate (MDI) and
hexamethylene diisocyanates (HDI). For this purpose, PLA based
polyurethane must have good strength and flexibility. Therefore,
polycaprolactone which has better flexibility were prepared with
PLA. An effective way to endow polylactic acid with toughness is
through chain-extension reaction of the polylactic acid pre-polymer
with polycaprolactone used as chain extender. Polyurethane prepared
from MDI showed brittle behaviour, while, polyurethane prepared
from HDI showed flexibility at same concentrations.
Abstract: Biometallic materials are the most important materials for use in biomedical applications especially in manufacturing a variety of biological artificial replacements in a modern worlds, e.g. hip, knee or shoulder joints, due to their advanced characteristics. Titanium (Ti) and its alloys are used extensively in biomedical applications based on their high specific strength and excellent corrosion resistance. Beta-Ti alloys containing completely biocompatible elements are exceptionally prospective materials for manufacturing of bioimplants. They have superior mechanical, chemical and electrochemical properties for use as biomaterials. These biomaterials have the ability to introduce the most important property of biochemical compatibility which is low elastic modulus. This review examines current information on the recent developments in alloying elements leading to improvements of beta Ti alloys for use as biomaterials. Moreover, this paper focuses mainly on the evolution, evaluation and development of the modulus of elasticity as an effective factor on the performance of beta alloys.
Abstract: This paper proposes a complementary combination scheme of affine projection algorithm (APA) filters with different order of input regressors. A convex combination provides an interesting way to keep the advantage of APA having different order of input regressors. Consequently, a novel APA which has the rapid convergence and the reduced steady-state error is derived. Experimental results show the good properties of the proposed algorithm.
Abstract: This paper deals with a proposal of a new
methodology for durability assessment of solidification product for
its safe further use. The new methodology is based on a review of the
current state of assessment of treated waste in Czech Republic and
abroad. The aim of the paper is to propose an optimal evaluation
methodology for verifying properties of solidification product to
ensure its safe further use in building industry.
Abstract: This paper conducts a comparison study using KES-FB and PhabrOmeter to measure 58 selected warp knitted fabric hand properties. Fabric samples were selected and measured by both KES-FB and PhabrOmeter. Results show differences between these two measurement methods. Smoothness and stiffness values obtained by KES-FB were found significant correlated (p value = 0.003 and 0.022) to the PhabrOmeter results while softness values between two measurement methods did not show significant correlation (p value = 0.828). Disagreements among these two measurement methods imply limitations on different mechanism principles when facing warp knitted fabrics. Subjective measurement methods and further studies are suggested in order to ascertain deeper investigation on the mechanisms of fabric hand perceptions.
Abstract: Microwave dielectric ceramic materials of
(Mg1-xNix)2(Ti0.95Sn0.05)O4 for x = 0.01, 0.03, 0.05, 0.07 and 0.09 were
prepared and sintered at 1250–1400 ºC. The microstructure and
microwave dielectric properties of the ceramic materials were
examined and measured. The observations shows that the content of
Ni2+ ions has little effect on the crystal structure, dielectric constant,
temperature coefficient of resonant frequency (τf) and sintering
temperatures of the ceramics. However, the quality values (Q×f) are
greatly improved due to the addition of Ni2+ ions. The present study
showed that the ceramic material prepared for x = 0.05 and sintered at
1325ºC had the best Q×f value of 392,000 GHz, about 23%
improvement compared with that of Mg2(Ti0.95Sn0.05)O4.
Abstract: In this article the problem of distributional moments estimation is considered. The new approach of moments estimation based on usage of the characteristic function is proposed. By statistical simulation technique author shows that new approach has some robust properties. For calculation of the derivatives of characteristic function there is used numerical differentiation. Obtained results confirmed that author’s idea has a certain working efficiency and it can be recommended for any statistical applications.
Abstract: A novel new vanadium (IV) complexes incorporating the chelating diamido cyclopentadienyl {ArN(CH2)3NAr)}2-((ηn-Cp)Cp)} (Ar = 2,6-Pri2C6H3)(Cp = C5H5 and n = 1,2,3,4 and 5) have been studied with calculation of the properties of species involved in various of cyclopentadienyl reaction. These were carried out under investigation of density functional theory (DFT) calculation, and comparing together. Other methods, explicitly including electron correlation, are necessary for more accurate calculations; MB3LYP (Becke) (Lee–Yang–Parr) level of theory often being used to obtain more exact results. These complexes were estimated of electronic energy for molecular system, because it accounts for all electron correlation interactions.
The optimised of [V(ArN(CH2)3NAr)2Cl(η5-Cp)] (Ar = 2,6-Pri2C6H3 and Cp= C5H5) was found to be thermally more stable than others of vanadium cyclopentadienyl. In the meantime the complex [V(ArN(CH2)3NAr)2Cl(η1-Cp)] (Ar = 2,6-Pri2C6H3 and Cp= C5H5) which is showed a low thermal stability in case of the just one carbon of cyclopentadienyl can be insertion with vanadium metal centre. By using Dewar-Chatt-Duncanson model, as a basis of the molecular orbital (MO) analysis and showed the highest occupied molecular orbital (HOMO) and lowest occupied molecular orbital LUMO.
Abstract: Ferulic acid has widespread industrial potential by virtue of its antioxidant properties. However, it is partially soluble in aqueous media, limiting their usefulness in oil-based processes in food, cosmetic, pharmaceutical, and material industry. Therefore, modification of ferulic acid should be made by producing of more lipophilic derivatives. In this study, a preliminary investigation of lipase-catalyzed trans-esterification reaction of ethyl ferulate and olive oil was investigated. The reaction was catalyzed by immobilized lipase from Candida antarctica (Novozym 435), to produce ferulate ester, a sunscreen agent. A statistical approach of Response surface methodology (RSM) was used to evaluate the interactive effects of reaction temperature (40-80°C), reaction time (4-12 hours), and amount of enzyme (0.1-0.5 g). The optimum conditions derived via RSM were reaction temperature 60°C, reaction time 2.34 hours, and amount of enzyme 0.3 g. The actual experimental yield was 59.6% ferulate ester under optimum condition, which compared well to the maximum predicted value of 58.0%.
Abstract: PAN nanofibers reinforced with amine functionalized
carbon nanotubes. The effect of amine functionalization and the
effect of concentration of CNT on the conductivity and mechanical
and morphological properties of composite nanofibers were
examined. 1%CNT-NH2 loaded PAN/CNT nanofiber showed the best
mechanical properties. Conductivity increased with the incorporation
of carbon nanotubes. While an increase of concentration of CNT
increases the diameter of nanofiber, the use of functionalized CNT
results to decrease of diameter of nanofiber.
Abstract: Polymer composite nano-fibers including (1, 3 wt %)
silver nano-particles have been produced by electrospinning method.
Polyacrylonitrile/N,N-dimethylformamide (PAN/DMF) solution have
been prepared and the amount of silver nitrate have been adjusted to
PAN weight. Silver nano-particles were obtained from reduction of
silver ions into silver nano-particles by chemical reduction by
hydrazine hydroxide (N2H5OH). The different amount of silver salt
was loaded into polymer matrix to obtain polyacrylonitrile composite
nano-fiber containing silver nano-particles. The effect of the amount
of silver nano-particles on the properties of composite nano-fiber web
was investigated. Electrical conductivity, mechanical properties,
thermal properties were examined by Microtest LCR Meter 6370
(0.01 mΩ-100 MΩ), Tensile tester, Differential scanning calorimeter
DSC (Q10) and SEM respectively. Also antimicrobial efficiency test
(ASTM E2149-10) was done against to Staphylococcus aureus
bacteria. It has been seen that breaking strength, conductivity,
antimicrobial effect, enthalpy during cyclization increase by use of
silver nano-particles while the diameter of nano-fiber decreases.
Abstract: Flanges are widely used for connecting valves, pipes and other industrial devices such as gearboxes. Method of producing a flange has a considerable impact on the manner of their involvement with the industrial engines and gearboxes. By Using die casting instead of sand casting and machining for manufacturing flanges, production speed and dimensional accuracy of the parts increases. Also, in die casting, obtained dimensions are close to final dimensions and hence the need for machining flanges after die casting process decreases which makes a significant savings in raw materials and improves the mechanical properties of flanges. In this paper, a typical die of an industrial helical gearbox flange (size ISO 50) was designed and die casting process for producing this type of flange was simulated using ProCAST software. The results of simulation were used for optimizing die design. Finally, using the results of the analysis, optimized die was built.
Abstract: Effect of 2wt% Cu addition on tensile properties and
fracture behavior of Al-6Si-0.5Mg-2Ni alloy at various strain rates
were studied. The solution treated Al-6Si-0.5Mg-2Ni (-2Cu) alloys,
were aged isochronally for 1 hour at temperatures up to 300oC. The
uniaxial tension test was carried out at strain rate ranging from 10-4s-1
to 10-2s-1 in order to investigate the strain rate dependence of tensile
properties. Tensile strengths were found to increase with ageing
temperature and the maximum being attained ageing for 1 hr at
225oC (peak aged condition). Addition of 2wt% Cu resulted in an
increase in tensile properties at all strain rates. Evaluation of tensile
properties at three different strain rates (10-4, 10-3 and 10-2 s-1)
showed that strain rates affected the tensile properties significantly.
At higher strain rates the strength was better but ductility was poor.
Microstructures of broken specimens showed that both the void
coalescence and the interface debonding affect the fracture behavior
of the alloys