Abstract: The objective of this study is to investigate the effect of adding coal to obtain insulating ceramic product. The preparation of mixtures is achieved with 04 types of different masse compositions, consisting of gray and yellow clay, and coal. Analyses are performed on local raw materials by adding coal as additive. The coal content varies from 5 to 20 % in weight by varying the size of coal particles ranging from 0.25mm to 1.60mm.
Initially, each natural moisture content of a raw material has been determined at the temperature of 105°C in a laboratory oven. The Influence of low-coal content on absorption, the apparent density, the contraction and the resistance during compression have been evaluated. The experimental results showed that the optimized composition could be obtained by adding 10% by weight of coal leading thus to insulating ceramic products with water absorption, a density and resistance to compression of 9.40 %, 1.88 g/cm3, 35.46 MPa, respectively. The results show that coal, when mixed with traditional raw materials, offers the conditions to be used as an additive in the production of lightweight ceramic products.
Abstract: The purpose of this study was to investigate the effects of computer–based instructional designs, namely modality and redundancy principles on the attitude and learning of music theory among primary pupils of different Music Intelligence levels. The lesson of music theory was developed in three different modes, audio and image (AI), text with image (TI) and audio with image and text (AIT). The independent variables were the three modes of courseware. The moderator variable was music intelligence. The dependent variables were the post test score. ANOVA was used to determine the significant differences of the pretest scores among the three groups. Analyses of covariance (ANCOVA) and Post hoc were carried out to examine the main effects as well as the interaction effects of the independent variables on the dependent variables. High music intelligence pupils performed significantly better than low music intelligence pupils in all the three treatment modes. The AI mode was found to help pupils with low music intelligence significantly more than the TI and AIT modes.
Abstract: In this paper, a new face recognition method based on
PCA (principal Component Analysis), LDA (Linear Discriminant
Analysis) and neural networks is proposed. This method consists of
four steps: i) Preprocessing, ii) Dimension reduction using PCA, iii)
feature extraction using LDA and iv) classification using neural
network. Combination of PCA and LDA is used for improving the
capability of LDA when a few samples of images are available and
neural classifier is used to reduce number misclassification caused by
not-linearly separable classes. The proposed method was tested on
Yale face database. Experimental results on this database
demonstrated the effectiveness of the proposed method for face
recognition with less misclassification in comparison with previous
methods.
Abstract: In the Fe-3%Si sheets, grade Hi-B, with AlN and MnS
as inhibitors, the Goss grains which abnormally grow do not have a
size greater than the average size of the primary matrix. In this
heterogeneous microstructure, the size factor is not a required
condition for the secondary recrystallization. The onset of the small
Goss grain abnormal growth appears to be related to a particular
behavior of their grain boundaries, to the local texture and to the
distribution of the inhibitors. The presence and the evolution of
oriented clusters ensure to the small Goss grains a favorable
neighborhood to grow. The modified Monte-Carlo approach, which
is applied, considers the local environment of each grain. The grain
growth is dependent of its real spatial position; the matrix
heterogeneity is then taken into account. The grain growth conditions
are considered in the global matrix and in different matrixes
corresponding to A component clusters. The grain growth behaviour
is considered with introduction of energy only, energy and mobility,
energy and mobility and precipitates.
Abstract: Among various testing methodologies, Built-in Self-
Test (BIST) is recognized as a low cost, effective paradigm. Also,
full adders are one of the basic building blocks of most arithmetic
circuits in all processing units. In this paper, an optimized testable 2-
bit full adder as a test building block is proposed. Then, a BIST
procedure is introduced to scale up the building block and to generate
a self testable n-bit full adders. The target design can achieve 100%
fault coverage using insignificant amount of hardware redundancy.
Moreover, Overall test time is reduced by utilizing polymorphic
gates and also by testing full adder building blocks in parallel.
Abstract: Linear two-point boundary value problems of order
two are solved using cubic trigonometric B-spline interpolation
method (CTBIM). Cubic trigonometric B-spline is a piecewise
function consisting of trigonometric equations. This method is tested
on some problems and the results are compared with cubic B-spline
interpolation method (CBIM) from the literature. CTBIM is found to
approximate the solution slightly more accurately than CBIM if the
problems are trigonometric.
Abstract: In this paper, a bond graph dynamic model for a valvecontrolled
hydraulic cylinder has been developed. A simplified bond
graph model of the inter-actuator interactions in a multi-cylinder
hydraulic system has also been presented. The overall bond graph
model of a valve-controlled hydraulic cylinder was developed by
combining the bond graph sub-models of the pump, spool valve and
the actuator using junction structures. Causality was then assigned
in order to obtain a computational model which could be simulated.
The causal bond graph model of the hydraulic cylinder was verified
by comparing the open loop state responses to those of an ODE
model which had been developed in literature based on the same
assumptions. The results were found to correlate very well both
in the shape of the curves, magnitude and the response times,
thus indicating that the developed model represents the hydraulic
dynamics of a valve-controlled cylinder. A simplified model for interactuator
interaction was presented by connecting an effort source with
constant pump pressure to the zero-junction from which the cylinders
in a multi-cylinder system are supplied with a constant pressure from
the pump. On simulating the state responses of the developed model
under different situations of cylinder operations, indicated that such
a simple model can be used to predict the inter-actuator interactions.
Abstract: This study explored the relationship between
psychological traits, demographics and financial behavioral biases for
individual investors in Taiwan stock market. By using questionnaire
survey method conducted in 2010, there are 554 valid convenient
samples collected to examine the determinants of three types of
behavioral biases. Based on literature review, two hypothesized
models are constructed and further used to evaluate the effects of big
five personality traits and demographic variables on investment biases
through Structural Equation Model (SEM) analysis. The results
showed that investment biases of individual investors are significantly
related to four personality traits as well as some demographics.
Abstract: Transient eddy current problem is solved in the
present paper by the method of the Laplace transform for the case of
a double conductor line located parallel to a conducting half-space.
The Fourier sine and cosine integral transforms are used in order to
find the Laplace transform of the solution. The inverse Laplace
transform of the solution is found in closed form. The integrated
electromotive force per unit length of the double conductor line is
calculated in the form of an improper integral.
Abstract: Camera calibration is an important step in 3D
reconstruction. Camera calibration may be classified into two major types: traditional calibration and self-calibration. However, a calibration method in using a checkerboard is intermediate between traditional calibration and self-calibration. A self
is proposed based on a square in this paper. Only a square in the planar
template, the camera self-calibration can be completed through the single view. The proposed algorithm is that the virtual circle and straight line are established by a square on planar template, and
circular points, vanishing points in straight lines and the relation
between them are be used, in order to obtain the image of the absolute
conic (IAC) and establish the camera intrinsic parameters. To make
the calibration template is simpler, as compared with the Zhang Zhengyou-s method. Through real experiments and experiments, the experimental results show that this algorithm is
feasible and available, and has a certain precision and robustness.
Abstract: Extraction of Fe(III) from aqueous solution using Trin-
butyl Phosphate (TBP) as carrier needs a highly acidic medium
(>6N) as it favours formation of chelating complex FeCl3.TBP.
Similarly, stripping of Iron(III) from loaded organic solvents requires
neutral pH or alkaline medium to dissociate the same complex. It is
observed that TBP co-extracts acids along with metal, which causes
reversal of driving force of extraction and iron(III) is re-extracted
back from the strip phase into the feed phase during Liquid Emulsion
Membrane (LEM) pertraction. Therefore, rate of extraction of
different mineral acids (HCl, HNO3, H2SO4) using TBP with and
without presence of metal Fe(III) was examined. It is revealed that in
presence of metal acid extraction is enhanced. Determination of mass
transfer coefficient of both acid and metal extraction was performed
by using Bulk Liquid Membrane (BLM). The average mass transfer
coefficient was obtained by fitting the derived model equation with
experimentally obtained data. The mass transfer coefficient of the
mineral acid extraction is in the order of kHNO3 = 3.3x10-6m/s > kHCl =
6.05x10-7m/s > kH2SO4 = 1.85x10-7m/s. The distribution equilibria of
the above mentioned acids between aqueous feed solution and a
solution of tri-n-butyl-phosphate (TBP) in organic solvents have been
investigated. The stoichiometry of acid extraction reveals the
formation of TBP.2HCl, HNO3.2TBP, and TBP.H2SO4 complexes.
Moreover, extraction of Iron(III) by TBP in HCl aqueous solution
forms complex FeCl3.TBP.2HCl while in HNO3 medium forms
complex 3FeCl3.TBP.2HNO3
Abstract: The absolute Cu atoms density in Cu(2S1/22P1/2)
ground state has been measured by Resonance Optical Absorption
(ROA) technique in a DC magnetron sputtering deposition with
argon. We measured these densities under variety of operation
conditions: pressure from 0.6 μbar to 14 μbar, input power from
10W to 200W and N2 mixture from 0% to 100%. For measuring the
gas temperature, we used the simulation of N2 rotational spectra
with a special computer code. The absolute number density of Cu
atoms decreases with increasing the N2 percentage of buffer gas at
any conditions of this work. But the deposition rate, is not decreased
with the same manner. The deposition rate variation is very small
and in the limit of quartz balance measuring equipment accuracy. So
we conclude that decrease in the absolute number density of Cu
atoms in magnetron plasma has not a big effect on deposition rate,
because the diffusion of Cu atoms to the chamber volume and
deviation of Cu atoms from direct path (towards the substrate)
decreases with increasing of N2 percentage of buffer gas. This is
because of the lower mass of N2 atoms compared to the argon ones.
Abstract: A collaboration among the Hospital S. Giovanni Battista
of Turin, the Politecnico of Turin, and the MUST company is
described. The content of the collaboration has been and is the use of
ICT-s, e-learning, and blended learning for the internal professional
education, training, and keeping up to date of the personnel of the
hospital. A platform for the delivery of the teaching materials has
been built, including an evaluation and self-evaluation tool. The first
on line courses have been developed and delivered and many more
are in preparation. The first results of the monitoring of the efficacy
of the online education have been positive.
Abstract: Many commercial processes are available for the
removal of H2S from gaseous streams. The desulfurization of gas
streams using aqueous ferric sulfate solution as washing liquor is
studied. Apart from sulfur, only H2O is generated in the process, and
consequently, no waste treatment facilities are required. A distinct
advantage of the process is that the reaction of H2S with is so rapid
and complete that there remains no danger of discharging toxic waste
gas. In this study, the reactive absorption of hydrogen sulfide into
aqueous ferric sulfate solution has been studied and design
calculations for equipments have been done and effective operation
parameters on this process considered. Results show that high
temperature and low pressure are suitable for absorption reaction.
Variation of hydrogen sulfide concentration and Fe3+ concentration
with time in absorption reaction shown that the reaction of ferric
sulfate and hydrogen sulfide is first order with respect to the both
reactant. At low Fe2(SO4)3 concentration the absorption rate of H2S
increase with increasing the Fe2(SO4)3 concentration. At higher
concentration a decrease in the absorption rate was found. At higher
concentration of Fe2(SO4)3, the ionic strength and viscosity of
solution increase remarkably resulting in a decrease of solubility,
diffusivity and hence absorption rate.
Abstract: The job shop scheduling problem (JSSP) is a
notoriously difficult problem in combinatorial optimization. This
paper presents a hybrid artificial immune system for the JSSP with the
objective of minimizing makespan. The proposed approach combines
the artificial immune system, which has a powerful global exploration
capability, with the local search method, which can exploit the optimal
antibody. The antibody coding scheme is based on the operation based
representation. The decoding procedure limits the search space to the
set of full active schedules. In each generation, a local search heuristic
based on the neighborhood structure proposed by Nowicki and
Smutnicki is applied to improve the solutions. The approach is tested
on 43 benchmark problems taken from the literature and compared
with other approaches. The computation results validate the
effectiveness of the proposed algorithm.
Abstract: α-Pinene is the main component of the most
turpentine oils. The hydration of α-pinene with acid catalysts leads to
a complex mixture of monoterpenes. In order to obtain more valuable
products, the α-pinene in the turpentine can be hydrated in dilute
mineral acid solutions to produce α-terpineol. The design of
separation processes requires information on phase equilibrium and
related thermodynamic properties. This paper reports the results of
study on liquid-liquid equilibrium (LLE) of system containing α-
pinene + water and α-terpineol + water.
Binary LLE for α-pinene + water system, and α-terpineol + water
systems were determined by experiment at 301K and atmospheric
pressure. The two component mixture was stirred for about 30min,
then the mixture was left for about 2h for complete phase separation.
The composition of both phases was analyzed by using a Gas
Chromatograph. The experimental data were correlated by
considering both NRTL and UNIQUAC activity coefficient models.
The LLE data for the system of α-pinene + water and α-terpineol +
water were correlated successfully by the NRTL model. The
experimental data were not satisfactorily fitted by the UNIQUAC
model. The NRTL model (α =0.3) correlates the LLE data for the
system of α-pinene + water at 301K with RMSD of 0.0404%. And
the NRTL model (α =0.61) at 301K with RMSD of 0.0058 %. The
NRTL model (α =0.3) correlates the LLE data for the system of α-
terpineol + water at 301K with RMSD of 0.1487% and the NRTL
model (α =0.6) at 301K with RMSD of 0.0032%, between the
experimental and calculated mole fractions.
Abstract: This study mainly aims at assessing the level of
microbial pollution of the water used in the chair system in dental
clinics. For this purpose 36 samples have been randomly collected
from a number of dental surgeries in the city of Tripoli in Libya.
However, 32 of the samples have tested positive to microbial
pollution including 13 of the samples, which have tested positives to
Pseudomonas aeruginosa. Based on the results of the test a further
investigation of the biofilms incorporated within the dental chair
system has been conducted. The laboratory tests of biofilms with
similar design to those found in dental chairs have proved that
bacterial pollution takes place through saliva of the patients who use
the chairs, and that this saliva is rich with nutrients which provides a
suitable breeding ground for all types of bacteria.
Abstract: System MEMORI automatically detects and recognizes
rotated and/or rescaled versions of the objects of a database within
digital color images with cluttered background. This task is accomplished
by means of a region grouping algorithm guided by heuristic
rules, whose parameters concern some geometrical properties and the
recognition score of the database objects. This paper focuses on the
strategies implemented in MEMORI for the estimation of the heuristic
rule parameters. This estimation, being automatic, makes the system
a self configuring and highly user-friendly tool.
Abstract: In this paper a combination approach of two heuristic-based algorithms: genetic algorithm and tabu search is proposed. It has been developed to obtain the least cost based on the split-pipe design of looped water distribution network. The proposed combination algorithm has been applied to solve the three well-known water distribution networks taken from the literature. The development of the combination of these two heuristic-based algorithms for optimization is aimed at enhancing their strengths and compensating their weaknesses. Tabu search is rather systematic and deterministic that uses adaptive memory in search process, while genetic algorithm is probabilistic and stochastic optimization technique in which the solution space is explored by generating candidate solutions. Split-pipe design may not be realistic in practice but in optimization purpose, optimal solutions are always achieved with split-pipe design. The solutions obtained in this study have proved that the least cost solutions obtained from the split-pipe design are always better than those obtained from the single pipe design. The results obtained from the combination approach show its ability and effectiveness to solve combinatorial optimization problems. The solutions obtained are very satisfactory and high quality in which the solutions of two networks are found to be the lowest-cost solutions yet presented in the literature. The concept of combination approach proposed in this study is expected to contribute some useful benefits in diverse problems.
Abstract: Reduced switching loss favours Pulse Skipping
Modulation mode of switching dc-to-dc converters at light loads.
Under certain conditions the converter operates in discontinuous
conduction mode (DCM). Inductor current starts from zero in each
switching cycle as the switching frequency is constant and not
adequately high. A DC-to-DC buck converter is modelled and
simulated in this paper under DCM. Effect of ESR of the filter
capacitor in input current frequency components is studied. The
converter is studied for its operation under input voltage and load
variation. The operating frequency is selected to be close to and
above audio range.