Abstract: This paper presents a new approach using Combined Artificial Neural Network (CANN) module for daily peak load forecasting. Five different computational techniques –Constrained method, Unconstrained method, Evolutionary Programming (EP), Particle Swarm Optimization (PSO), and Genetic Algorithm (GA) – have been used to identify the CANN module for peak load forecasting. In this paper, a set of neural networks has been trained with different architecture and training parameters. The networks are trained and tested for the actual load data of Chennai city (India). A set of better trained conventional ANNs are selected to develop a CANN module using different algorithms instead of using one best conventional ANN. Obtained results using CANN module confirm its validity.
Abstract: Directional over current relays (DOCR) are commonly used in power system protection as a primary protection in distribution and sub-transmission electrical systems and as a secondary protection in transmission systems. Coordination of protective relays is necessary to obtain selective tripping. In this paper, an approach for efficiency reduction of DOCRs nonlinear optimum coordination (OC) is proposed. This was achieved by modifying the objective function and relaxing several constraints depending on the four constraints classification, non-valid, redundant, pre-obtained and valid constraints. According to this classification, the far end fault effect on the objective function and constraints, and in consequently on relay operating time, was studied. The study was carried out, firstly by taking into account the near-end and far-end faults in DOCRs coordination problem formulation; and then faults very close to the primary relays (nearend faults). The optimal coordination (OC) was achieved by simultaneously optimizing all variables (TDS and Ip) in nonlinear environment by using of Genetic algorithm nonlinear programming techniques. The results application of the above two approaches on 6-bus and 26-bus system verify that the far-end faults consideration on OC problem formulation don-t lose the optimality.
Abstract: This paper considers the autonomous navigation
problem of multiple n-link nonholonomic mobile manipulators within
an obstacle-ridden environment. We present a set of nonlinear
acceleration controllers, derived from the Lyapunov-based control
scheme, which generates collision-free trajectories of the mobile
manipulators from initial configurations to final configurations in a
constrained environment cluttered with stationary solid objects of
different shapes and sizes. We demonstrate the efficiency of the
control scheme and the resulting acceleration controllers of the
mobile manipulators with results through computer simulations of an
interesting scenario.
Abstract: An experiment was conducted with 80 unsexed
broilers of the Arbor Acress strain to determine the capability of a
carrot and fruit juice wastes mixture (carrot, apple, manggo, avocado,
orange, melon and Dutch egg plant) in the same proportion for
replacing corn in broiler diet. This study involved a completely
randomized design (CRD) with 5 treatments (0, 5, 10, 15, and 20% of
juice wastes mixture in diets) and 4 replicates per treatment. Diets
were isonitrogenous (22% crude protein) and isocaloric (3000 kcal/kg
diet). Measured variables were feed consumption, average daily
gain, feed conversion, as well as percentages of abdominal fat pad,
carcass, digestive organs (liver, pancreas and gizzard), and heart.
Data were analyzed by analysis of variance for CRD. Increasing
juice wastes mixture levels in diets increased feed consumption
(P
Abstract: Let G be a graph of order n, and let k 2 and m 0 be two integers. Let h : E(G) [0, 1] be a function. If e∋x h(e) = k holds for each x V (G), then we call G[Fh] a fractional k-factor of G with indicator function h where Fh = {e E(G) : h(e) > 0}. A graph G is called a fractional (k,m)-deleted graph if there exists a fractional k-factor G[Fh] of G with indicator function h such that h(e) = 0 for any e E(H), where H is any subgraph of G with m edges. In this paper, it is proved that G is a fractional (k,m)-deleted graph if (G) k + m + m k+1 , n 4k2 + 2k − 6 + (4k 2 +6k−2)m−2 k−1 and max{dG(x), dG(y)} n 2 for any vertices x and y of G with dG(x, y) = 2. Furthermore, it is shown that the result in this paper is best possible in some sense.
Abstract: This paper presents the visual control flow support of Visual Modeling and Transformation System (VMTS), which facilitates composing complex model transformations out of simple transformation steps and executing them. The VMTS Visual Control Flow Language (VCFL) uses stereotyped activity diagrams to specify control flow structures and OCL constraints to choose between different control flow branches. This work discusses the termination properties of VCFL and provides an algorithm to support the termination analysis of VCFL transformations.
Abstract: In this paper a systematic method via H∞ control
design is proposed to select a sensor set that satisfies a number
of input criteria for a MAGLEV suspension system. The proposed
method recovers a number of optimised controllers for each possible
sensor set that satisfies the performance and constraint criteria using
evolutionary algorithms.
Abstract: The mountain road slope failures triggered by
earthquake activities and torrential rain namely to create the disaster.
Province Road No. 24 is a main route to the Wutai Township. The area
of the study is located at the mileages between 46K and 47K along the
road. However, the road has been suffered frequent damages as a result
of landslide and slope failures during typhoon seasons. An
understanding of the sliding behaviors in the area appears to be
necessary. Slope failures triggered by earthquake activities and heavy
rainfalls occur frequently. The study is to understand the mechanism
of slope failures and to look for the way to deal with the situation. In
order to achieve these objectives, this paper is based on theoretical and
structural geology data interpretation program to assess the potential
slope sliding behavior. The study showed an intimate relationship
between the landslide behavior of the slopes and the stratum materials,
based on structural geology analysis method to analysis slope stability
and finds the slope safety coefficient to predict the sites of destroyed
layer. According to the case study and parameter analyses results, the
slope mainly slips direction compared to the site located in the
southeast area. Find rainfall to result in the rise of groundwater level is
main reason of the landslide mechanism. Future need to set up
effective horizontal drain at corrective location, that can effective
restrain mountain road slope failures and increase stability of slope.
Abstract: An effect of rolling temperature on the mechanical properties and microstructural evolution of an Al-Mg-Si alloy was studied. The material was rolled up to a true strain of ~0.7 at three different temperatures viz; room temperature, liquid propanol and liquid nitrogen. The liquid nitrogen rolled sample exhibited superior properties with a yield and tensile strength of 332 MPa and 364 MPa, respectively, with a reasonably good ductility of ~9%. The liquid nitrogen rolled sample showed around 54 MPa increase in tensile strength without much reduction in the ductility as compared to the as received T6 condition alloy. The microstructural details revealed equiaxed grains in the annealed and solutionized sample and elongated grains in the rolled samples. In addition, the cryorolled samples exhibited fine grain structure compared to the room temperature rolled samples.
Abstract: The requirements analysis, modeling, and simulation have consistently been one of the main challenges during the development of complex systems. The scenarios and the state machines are two successful models to describe the behavior of an interactive system. The scenarios represent examples of system execution in the form of sequences of messages exchanged between objects and are a partial view of the system. In contrast, state machines can represent the overall system behavior. The automation of processing scenarios in the state machines provide some answers to various problems such as system behavior validation and scenarios consistency checking. In this paper, we propose a method for translating scenarios in state machines represented by Discreet EVent Specification and procedure to detect implied scenarios. Each induced DEVS model represents the behavior of an object of the system. The global system behavior is described by coupling the atomic DEVS models and validated through simulation. We improve the validation process with integrating formal methods to eliminate logical inconsistencies in the global model. For that end, we use the Z notation.
Abstract: The tree structured approach of non-uniform filterbank
(NUFB) is normally used in perfect reconstruction (PR). The PR is
not always feasible due to certain limitations, i.e, constraints in
selecting design parameters, design complexity and some times
output is severely affected by aliasing error if necessary and
sufficient conditions of PR is not satisfied perfectly. Therefore, there
has been generalized interest of researchers to go for near perfect
reconstruction (NPR). In this proposed work, an optimized tree
structure technique is used for the design of NPR non-uniform
filterbank. Window functions of Blackman family are used to design
the prototype FIR filter. A single variable linear optimization is used
to minimize the amplitude distortion. The main feature of the
proposed design is its simplicity with linear phase property.
Abstract: Reentry trajectory optimization is a multi-constraints
optimal control problem which is hard to solve. To tackle it, we
proposed a new algorithm named CDEN(Constrained Differential
Evolution Newton-Raphson Algorithm) based on Differential Evolution(
DE) and Newton-Raphson.We transform the infinite dimensional
optimal control problem to parameter optimization which is finite
dimensional by discretize control parameter. In order to simplify
the problem, we figure out the control parameter-s scope by process
constraints. To handle constraints, we proposed a parameterless constraints
handle process. Through comprehensive analyze the problem,
we use a new algorithm integrated by DE and Newton-Raphson to
solve it. It is validated by a reentry vehicle X-33, simulation results
indicated that the algorithm is effective and robust.
Abstract: The Expert Witness Testimony in the Battered
Woman Syndrome Expert witness testimony (EWT) is a kind of
information given by an expert specialized in the field (here in BWS)
to the jury in order to help the court better understand the case. EWT
does not always work in favor of the battered women. Two main
decision-making models are discussed in the paper: the Mathematical
model and the Explanation model. In the first model, the jurors
calculate ″the importance and strength of each piece of evidence″
whereas in the second model they try to integrate the EWT with the
evidence and create a coherent story that would describe the crime.
The jury often misunderstands and misjudges battered women for
their action (or in this case inaction). They assume that these women
are masochists and accept being mistreated for if a man abuses a
woman constantly, she should and could divorce him or simply leave
at any time. The research in the domain found that indeed, expert
witness testimony has a powerful influence on juror’s decisions thus
its quality needs to be further explored. One of the important factors
that need further studies is a bias called the dispositionist worldview
(a belief that what happens to people is of their own doing). This
kind of attributional bias represents a tendency to think that a
person’s behavior is due to his or her disposition, even when the
behavior is clearly attributed to the situation. Hypothesis The
hypothesis of this paper is that if a juror has a dispositionist
worldview then he or she will blame the rape victim for triggering the
assault. The juror would therefore commit the fundamental
attribution error and believe that the victim’s disposition caused the
rape and not the situation she was in. Methods The subjects in the
study were 500 randomly sampled undergraduate students from
McGill, Concordia, Université de Montréal and UQAM.
Dispositional Worldview was scored on the Dispositionist
Worldview Questionnaire. After reading the Rape Scenarios, each
student was asked to play the role of a juror and answer a
questionnaire consisting of 7 questions about the responsibility,
causality and fault of the victim. Results The results confirm the
hypothesis which states that if a juror has a dispositionist worldview
then he or she will blame the rape victim for triggering the assault.
By doing so, the juror commits the fundamental attribution error
because he will believe that the victim’s disposition, and not the
constraints or opportunities of the situation, caused the rape scenario.
Abstract: Reinforced concrete stair slabs with mid landings i.e.
Dog-legged shaped are conventionally designed as per specifications
of standard codes of practices which guide about the effective span
according to the varying support conditions. Presently, the behavior
of such slabs has been investigated using Finite Element method. A
single flight stair slab with landings on both sides and supported at
ends on wall, and a multi flight stair slab with landings and six
different support arrangements have been analyzed. The results
obtained for stresses, strains and deflections are used to describe the
behavior of such stair slabs, including locations of critical moments
and deflections. Values of critical moments obtained by F.E. analysis
have also have been compared with that obtained from conventional
analysis. Analytical results show that the moments are also critical
near the kinks i.e. junction of mid-landing and inclined waist slab.
This change in the behavior of dog-legged stair slab may be due to
continuity of the material in transverse direction in two landings
adjoining the waist slab, hence additional stiffness achieved. This
change in the behavior is generally not taken care of in conventional
method of design.
Abstract: Designing modern machine tools is a complex task. A
simulation tool to aid the design work, a virtual machine, has
therefore been developed in earlier work. The virtual machine
considers the interaction between the mechanics of the machine
(including structural flexibility) and the control system. This paper
exemplifies the usefulness of the virtual machine as a tool for product
development. An optimisation study is conducted aiming at
improving the existing design of a machine tool regarding weight and
manufacturing accuracy at maintained manufacturing speed. The
problem can be categorised as constrained multidisciplinary multiobjective
multivariable optimisation. Parameters of the control and
geometric quantities of the machine are used as design variables. This
results in a mix of continuous and discrete variables and an
optimisation approach using a genetic algorithm is therefore
deployed. The accuracy objective is evaluated according to
international standards. The complete systems model shows nondeterministic
behaviour. A strategy to handle this based on statistical
analysis is suggested. The weight of the main moving parts is reduced
by more than 30 per cent and the manufacturing accuracy is
improvement by more than 60 per cent compared to the original
design, with no reduction in manufacturing speed. It is also shown
that interaction effects exist between the mechanics and the control,
i.e. this improvement would most likely not been possible with a
conventional sequential design approach within the same time, cost
and general resource frame. This indicates the potential of the virtual
machine concept for contributing to improved efficiency of both
complex products and the development process for such products.
Companies incorporating such advanced simulation tools in their
product development could thus improve its own competitiveness as
well as contribute to improved resource efficiency of society at large.
Abstract: The hydro-mechanical model for unsaturated soils has
been presented based on the effective stress principle taking into
account effects of drying-wetting process. The elasto-plastic
constitutive equations for stress-strain relations of the soil skeleton
have been established. A plasticity model is modified from modified
Cam-Clay model. The hardening rule has been established by
considering the isotropic consolidation paths. The effect of dryingwetting
process is introduced through the ¤ç parameter. All model
coefficients are identified in terms of measurable parameters. The
simulations from the proposed model are compared with the
experimental results. The model calibration was performed to extract
the model parameter from the experimental results. Good agreement
between the results predicted using proposed model and the
experimental results was obtained.
Abstract: Based on the standard finite element method, a new
finite element method which is known as nonlocal finite element
method (NL-FEM) is numerically implemented in this article to
study the nonlocal effects for solving 1D nonlocal elastic problem.
An Eringen-type nonlocal elastic model is considered. In this model,
the constitutive stress-strain law is expressed interms of integral
equation which governs the nonlocal material behavior. The new
NL-FEM is adopted in such a way that the postulated nonlocal elastic
behavior of material is captured by a finite element endowed with a
set of (cross-stiffness) element itself by the other elements in mesh.
An example with their analytical solutions and the relevant numerical
findings for various load and boundary conditions are presented and
discussed in details. It is observed from the numerical solutions that
the torsional deformation angle decreases with increasing nonlocal
nanoscale parameter. It is also noted that the analytical solution fails
to capture the nonlocal effect in some cases where numerical
solutions handle those situation effectively which prove the
reliability and effectiveness of numerical techniques.
Abstract: Wikis are considered to be part of Web 2.0
technologies that potentially support collaborative learning and
writing. Wikis provide opportunities for multiple users to work on
the same document simultaneously. Most wikis have also a page for
written group discussion. Nevertheless, wikis may be used in
different ways depending on the pedagogy being used, and the
constraints imposed by the course design. This work explores
students- uses of wiki in teacher education. The analysis is based on a
taxonomy for classifying students- activities and actions carried out
on the wiki. The article also discusses the implications for using
wikis as collaborative writing tools in teacher education.
Abstract: In the globalization context and competitiveness, the role of a university is further enhanced. University is no longer confined to traditional roles. Universities need to interact with others in order to be relevant and progressive. Symbiosis relationships between the university and industry are very significant because the relationship between those two can foster economic development of a nation. In a world of fast changing technology and competition, it is necessary for the university to collaborate with industry to combine efforts fostering the diffusion of knowledge, increasing research and development, patenting innovation and commercializing products. It has become increasingly accepted that the necessity of close university-industry interactions as a mean of national economic prosperity. Therefore, this paper is aim to examine the level of linkages in university-industry interactions to which promotes the regional economic growth and development. This paper will explore the formation of linkages between the Higher Education Institution (University Technology MARA) and industries located in the Klang Valley region of Malaysia. It will present the university-industry linkages with emphasis on the type of linkages existed, the benefits of having such linkages to promote regional economic development and finally the constraints that might impede the linkages and potentials to enhance the linkages towards economic growth and development.
Abstract: Aluminum alloy sheets have several advantages such
as the lightweight, high-specific strength and recycling efficiency.
Therefore, aluminum alloy sheets in sheet forming have been used in various areas as automotive components and so forth. During the
process of sheet forming, wrinkling which is caused by compression stress might occur and the formability of sheets was affected by
occurrence of wrinkling. A few studies of uniaxial compressive test by
using square tubes, pipes and sheets were carried out to clarify the each wrinkling behavior. However, on uniaxial compressive test,
deformation behavior of the sheets hasn-t be cleared. Then, it is necessary to clarify the relationship between the buckling behavior
and the forming conditions. In this study, the effect of dimension of the sheet in the buckling behavior on compression test of aluminum alloy sheet was cleared by experiment and FEA. As the results, the buckling
deformation was classified by three modes in terms of the distribution of equivalent plastic strain.