Abstract: In this paper, we address the problem of adaptive radio
resource allocation (RRA) and packet scheduling in the downlink of a
cellular OFDMA system, and propose a downlink multi-carrier
proportional fair (MPF) scheduler and its joint with adaptive RRA
algorithm to distribute radio resources among multiple users according
to their individual QoS requirements. The allocation and scheduling
objective is to maximize the total throughput, while at the same time
maintaining the fairness among users. The simulation results
demonstrate that the methods presented provide for user more explicit
fairness relative to RRA algorithm, but the joint scheme achieves the
higher sum-rate capacity with flexible parameters setting compared
with MPF scheduler.
Abstract: Recent advancements in sensor technologies and
Wireless Body Area Networks (WBANs) have led to the
development of cost-effective healthcare devices which can be used
to monitor and analyse a person-s physiological parameters from
remote locations. These advancements provides a unique opportunity
to overcome current healthcare challenges of low quality service
provisioning, lack of easy accessibility to service varieties, high costs
of services and increasing population of the elderly experienced
globally. This paper reports on a prototype implementation of an
architecture that seamlessly integrates Wireless Body Area Network
(WBAN) with Web services (WS) to proactively collect
physiological data of remote patients to recommend diagnostic
services. Technologies based upon WBAN and WS can provide
ubiquitous accessibility to a variety of services by allowing
distributed healthcare resources to be massively reused to provide
cost-effective services without individuals physically moving to the
locations of those resources. In addition, these technologies can
reduce costs of healthcare services by allowing individuals to access
services to support their healthcare. The prototype uses WBAN body
sensors implemented on arduino fio platforms to be worn by the
patient and an android smart phone as a personal server. The
physiological data are collected and uploaded through GPRS/internet
to the Medical Health Server (MHS) to be analysed. The prototype
monitors the activities, location and physiological parameters such as
SpO2 and Heart Rate of the elderly and patients in rehabilitation.
Medical practitioners would have real time access to the uploaded
information through a web application.
Abstract: In this paper we proposed a method for finding video
frames representing one sign in the finger alphabet. The method is
based on determining hands location, segmentation and the use of
standard video quality evaluation metrics. Metric calculation is
performed only in regions of interest. Sliding mechanism for finding
local extrema and adaptive threshold based on local averaging is used
for key frames selection. The success rate is evaluated by recall,
precision and F1 measure. The method effectiveness is compared
with metrics applied to all frames. Proposed method is fast, effective
and relatively easy to realize by simple input video preprocessing
and subsequent use of tools designed for video quality measuring.
Abstract: With data centers, end-users can realize the pervasiveness of services that will be one day the cornerstone of our lives. However, data centers are often classified as computing systems that consume the most amounts of power. To circumvent such a problem, we propose a self-adaptive weighted sum methodology that jointly optimizes the performance and power consumption of any given data center. Compared to traditional methodologies for multi-objective optimization problems, the proposed self-adaptive weighted sum technique does not rely on a systematical change of weights during the optimization procedure. The proposed technique is compared with the greedy and LR heuristics for large-scale problems, and the optimal solution for small-scale problems implemented in LINDO. the experimental results revealed that the proposed selfadaptive weighted sum technique outperforms both of the heuristics and projects a competitive performance compared to the optimal solution.
Abstract: The major part of light weight timber constructions
consists of insulation. Mineral wool is the most commonly used
insulation due to its cost efficiency and easy handling. The fiber
orientation and porosity of this insulation material enables flowthrough.
The air flow resistance is low. If leakage occurs in the
insulated bay section, the convective flow may cause energy losses
and infiltration of the exterior wall with moisture and particles. In
particular the infiltrated moisture may lead to thermal bridges and
growth of health endangering mould and mildew. In order to prevent
this problem, different numerical calculation models have been
developed. All models developed so far have a potential for
completion. The implementation of the flow-through properties of
mineral wool insulation may help to improve the existing models.
Assuming that the real pressure difference between interior and
exterior surface is larger than the prescribed pressure difference in the
standard test procedure for mineral wool ISO 9053 / EN 29053,
measurements were performed using the measurement setup for
research on convective moisture transfer “MSRCMT".
These measurements show, that structural inhomogeneities of
mineral wool effect the permeability only at higher pressure
differences, as applied in MSRCMT. Additional microscopic
investigations show, that the location of a leak within the
construction has a crucial influence on the air flow-through and the
infiltration rate. The results clearly indicate that the empirical values
for the acoustic resistance of mineral wool should not be used for the
calculation of convective transfer mechanisms.
Abstract: This paper reports the tensile fracture location
characterizations of dissimilar friction stir welds between 5754
aluminium alloy and C11000 copper. The welds were produced using
three shoulder diameter tools; namely, 15, 18 and 25 mm by varying
the process parameters. The rotational speeds considered were 600,
950 and 1200 rpm while the feed rates employed were 50, 150 and
300 mm/min to represent the low, medium and high settings
respectively. The tensile fracture locations were evaluated using the
optical microscope to identify the fracture locations and were
characterized. It was observed that 70% of the tensile samples failed
in the Thermo Mechanically Affected Zone (TMAZ) of copper at the
weld joints. Further evaluation of the fracture surfaces of the pulled
tensile samples revealed that welds with low Ultimate Tensile
Strength either have defects or intermetallics present at their joint
interfaces.
Abstract: In this paper, a new time-delay estimation
technique based on the cross IB-energy operator [5] is
introduced. This quadratic energy detector measures how
much a signal is present in another one. The location of the
peak of the energy operator, corresponding to the maximum of
interaction between the two signals, is the estimate of the
delay. The method is a fully data-driven approach. The
discrete version of the continuous-time form of the cross IBenergy
operator, for its implementation, is presented. The
effectiveness of the proposed method is demonstrated on real
underwater acoustic signals arriving from targets and the
results compared to the cross-correlation method.
Abstract: Experimental investigations were carried out in the
Manchester Tidal flow Facility (MTF) to study the flow patterns in
the region around and adjacent to a hypothetical headland in tidal
(oscillatory) ambient flow. The Planar laser-induced fluorescence
(PLIF) technique was used for visualization, with fluorescent dye
released at specific points around the headland perimeter and in its
adjacent recirculation zone. The flow patterns can be generalized into
the acceleration, stable flow and deceleration stages for each halfcycle,
with small variations according to location, which are more
distinct for low Keulegan-Carpenter number (KC) cases. Flow
patterns in the mixing region are unstable and complex, especially in
the recirculation zone. The flow patterns are in agreement with
previous visualizations, and support previous results in steady
ambient flow. It is suggested that the headland lee could be a viable
location for siting of pollutant outfalls.
Abstract: Trust management and Reputation models are
becoming integral part of Internet based applications such as CSCW,
E-commerce and Grid Computing. Also the trust dimension is a
significant social structure and key to social relations within a
collaborative community. Collaborative Decision Making (CDM) is
a difficult task in the context of distributed environment (information
across different geographical locations) and multidisciplinary
decisions are involved such as Virtual Organization (VO). To aid
team decision making in VO, Decision Support System and social
network analysis approaches are integrated. In such situations social
learning helps an organization in terms of relationship, team
formation, partner selection etc. In this paper we focus on trust
learning. Trust learning is an important activity in terms of
information exchange, negotiation, collaboration and trust
assessment for cooperation among virtual team members. In this
paper we have proposed a reinforcement learning which enhances the
trust decision making capability of interacting agents during
collaboration in problem solving activity. Trust computational model
with learning that we present is adapted for best alternate selection of
new project in the organization. We verify our model in a multi-agent
simulation where the agents in the community learn to identify
trustworthy members, inconsistent behavior and conflicting behavior
of agents.
Abstract: Recently studies in area of supply chain network
(SCN) have focused on the disruption issues in distribution systems.
Also this paper extends the previous literature by providing a new biobjective
model for cost minimization of designing a three echelon
SCN across normal and failure scenarios with considering multi
capacity option for manufacturers and distribution centers. Moreover,
in order to solve the problem by means of LINGO software, novel
model will be reformulated through a branch of LP-Metric method
called Min-Max approach.
Abstract: In this paper, we investigate the study of techniques
for scheduling users for resource allocation in the case of multiple
input and multiple output (MIMO) packet transmission systems. In
these systems, transmit antennas are assigned to one user or
dynamically to different users using spatial multiplexing. The
allocation of all transmit antennas to one user cannot take full
advantages of multi-user diversity. Therefore, we developed the case
when resources are allocated dynamically. At each time slot users
have to feed back their channel information on an uplink feedback
channel. Channel information considered available in the schedulers
is the zero forcing (ZF) post detection signal to interference plus
noise ratio. Our analysis study concerns the round robin and the
opportunistic schemes.
In this paper, we present an overview and a complete capacity
analysis of these schemes. The main results in our study are to give
an analytical form of system capacity using the ZF receiver at the
user terminal. Simulations have been carried out to validate all
proposed analytical solutions and to compare the performance of
these schemes.
Abstract: This paper presents a method for the optimal
allocation of Distributed generation in distribution systems. In this
paper, our aim would be optimal distributed generation allocation for
voltage profile improvement and loss reduction in distribution
network. Genetic Algorithm (GA) was used as the solving tool,
which referring two determined aim; the problem is defined and
objective function is introduced. Considering to fitness values
sensitivity in genetic algorithm process, there is needed to apply load
flow for decision-making. Load flow algorithm is combined
appropriately with GA, till access to acceptable results of this
operation. We used MATPOWER package for load flow algorithm
and composed it with our Genetic Algorithm. The suggested method
is programmed under MATLAB software and applied ETAP
software for evaluating of results correctness. It was implemented on
part of Tehran electricity distributing grid. The resulting operation of
this method on some testing system is illuminated improvement of
voltage profile and loss reduction indexes.
Abstract: Heat source addition to the axisymmetric supersonic
inlet may improve the performance parameters, which will increase
the inlet efficiency. In this investigation the heat has been added to
the flow field at some distance ahead of an axisymmetric inlet by
adding an imaginary thermal source upstream of cowl lip. The effect
of heat addition on the drag coefficient, mass flow rate and the
overall efficiency of the inlet have been investigated. The results
show that heat addition causes flow separation, hence to prevent this
phenomena, roughness has been added on the spike surface.
However, heat addition reduces the drag coefficient and the inlet
mass flow rate considerably. Furthermore, the effects of position,
size, and shape on the inlet performance were studied. It is found that
the thermal source deflects the flow streamlines. By improper
location of the thermal source, the optimum condition has been
obtained. For the optimum condition, the drag coefficient is
considerably reduced and the inlet mass flow rate and its efficiency
have been increased slightly. The optimum shape of the heat source
is obtained too.
Abstract: The intermittent connectivity modifies the “always
on" network assumption made by all the distributed query processing
systems. In modern- day systems, the absence of network
connectivity is considered as a fault. Since the last upload, it might
not be feasible to transmit all the data accumulated right away over
the available connection. It is possible that vital information may be
delayed excessively when the less important information takes place
of the vital information. Owing to the restricted and uneven
bandwidth, it is vital that the mobile nodes make the most
advantageous use of the connectivity when it arrives. Hence, in order
to select the data that needs to be transmitted first, some sort of data
prioritization is essential. A continuous query processing system for
intermittently connected mobile networks that comprises of a delaytolerant
continuous query processor distributed across the mobile
hosts has been proposed in this paper. In addition, a mechanism for
prioritizing query results has been designed that guarantees enhanced
accuracy and reduced delay. It is illustrated that our architecture
reduces the client power consumption, increases query efficiency by
the extensive simulation results.
Abstract: Numerical studies have been carried out using a
validated two-dimensional RNG k-epsilon turbulence model for the
design optimization of a thrust vector control system using shock
induced supersonic secondary jet. Parametric analytical studies have
been carried out with various secondary jets at different divergent
locations, jet interaction angles, jet pressures. The results from the
parametric studies of the case on hand reveal that the primary nozzle
with a small divergence angle, downstream injections with a distance
of 2.5 times the primary nozzle throat diameter from the primary
nozzle throat location warrant higher efficiency over a certain range
of jet pressures and jet angles. We observed that the supersonic
secondary jet opposing the core flow with jets interaction angle of
40o to the axis far downstream of the nozzle throat facilitates better
thrust vectoring than the secondary jet with same direction as that of
core flow with various interaction angles. We concluded that fixing
of the supersonic secondary jet nozzle pointing towards the throat
direction with suitable angle at a distance 2 to 4 times of the primary
nozzle throat diameter, as the case may be, from the primary nozzle
throat location could facilitate better thrust vectoring for the
supersonic aerospace vehicles.
Abstract: Transition prediction of boundary layers has always
been an important problem in fluid mechanics both theoretically and
practically, yet notwithstanding the great effort made by many
investigators, there is no satisfactory answer to this problem. The most
popular method available is so-called e-N method which is heavily
dependent on experiments and experience. The author has proposed
improvements to the e-N method, so to reduce its dependence on
experiments and experience to a certain extent. One of the key
assumptions is that transition would occur whenever the velocity
amplitude of disturbance reaches 1-2% of the free stream velocity.
However, the reliability of this assumption needs to be verified. In this
paper, transition prediction on a flat plate is investigated by using both
the improved e-N method and the parabolized stability equations (PSE)
methods. The results show that the transition locations predicted by
both methods agree reasonably well with each other, under the above
assumption. For the supersonic case, the critical velocity amplitude in
the improved e-N method should be taken as 0.013, whereas in the
subsonic case, it should be 0.018, both are within the range 1-2%.
Abstract: Distance visualization of large datasets often takes the direction of remote viewing and zooming techniques of stored static images. However, the continuous increase in the size of datasets and visualization operation causes insufficient performance with traditional desktop computers. Additionally, the visualization techniques such as Isosurface depend on the available resources of the running machine and the size of datasets. Moreover, the continuous demand for powerful computing powers and continuous increase in the size of datasets results an urgent need for a grid computing infrastructure. However, some issues arise in current grid such as resources availability at the client machines which are not sufficient enough to process large datasets. On top of that, different output devices and different network bandwidth between the visualization pipeline components often result output suitable for one machine and not suitable for another. In this paper we investigate how the grid services could be used to support remote visualization of large datasets and to break the constraint of physical co-location of the resources by applying the grid computing technologies. We show our grid enabled architecture to visualize large medical datasets (circa 5 million polygons) for remote interactive visualization on modest resources clients.
Abstract: In a BFWA (Broadband Fixed Wireless Access Network) the evolved SINR (Signal to Interference plus Noise Ratio) is relevant influenced by the applied duplex method. The TDD (Time Division Duplex), especially adaptive TDD method has some advantage contrary to FDD (Frequency Division Duplex), for example the spectrum efficiency and flexibility. However these methods are suffering several new interference situations that can-t occur in a FDD system. This leads to reduced SINR in the covered area what could cause some connection outages. Therefore, countermeasure techniques against interference are necessary to apply in TDD systems. Synchronization is one way to handling the interference. In this paper the TDD systems – applying different system synchronization degree - will be compared by the evolved SINR at different locations of the BFWA service area and the percentage of the covered area by the system.
Abstract: In this paper a new approach for transmission pricing
is presented. The main idea is voltage angle allocation, i.e.
determining the contribution of each contract on the voltage angle of
each bus. DC power flow is used to compute a primary solution for
angle decomposition. To consider the impacts of system non-linearity
on angle decomposition, the primary solution is corrected in different
iterations of decoupled Newton-Raphson power flow. Then, the
contribution of each contract on power flow of each transmission line
is computed based on angle decomposition. Contract-related flows
are used as a measure for “extent of use" of transmission network
capacity and consequently transmission pricing. The presented
approach is applied to a 4-bus test system and IEEE 30-bus test
system.
Abstract: Obesity is frequent attendant phenomenon of patients
with endocrinological disease. Between BMI and endocrinological
diseases is close correlation. In thesis we focused on the allocation of
hormone concentration – PTH and TSH, CHOL a mineral element Ca
in a blood serum. The examined group was formed by 100
respondents (women) aged 36 – 83 years, who were divided into two
groups – control group (CG), group with diagnosed endocrine disease
(DED). The concentration of PTH and TSH, Ca and CHOL was
measured through the medium of analyzers Cobas e411 (Japan);
Cobas Integra 400 (Switzerland). At individuals was measured body
weight as well as stature and thereupon from those data we
enumerated BMI. On the basis of Student T-test in biochemical
parameter of PTH and Ca we found out significantly meaningful
difference (p