Abstract: An effort to find out the smaller size of cuttings for propagation of Morus alba was made in experimental area Department of Forestry, Range Management and Wildlife, University of Agriculture, Faisalabad, Pakistan. Different size of cuttings i.e. 2", 4", 6" and 8" were planted in polythene tubes of 3.5"x7". The effort was also made to compare the performance of cuttings in open air and in polythene low tunnel. Root length, number of root branches, root diameter and root fresh and dry weight were found maximum in two inches cuttings while minimum in four inches cuttings. Root growth was found maximum in open air as compared to under polythene sheet.
Abstract: The antioxidant compounds are needed for the food, beverages, and pharmaceuticals industry. For this purpose, an appropriate method is required to measure the antioxidant properties in various types of samples. Spectrophotometric method usually used has some weaknesses, including the high price, long sample preparation time, and less sensitivity. Among the alternative methods developed to overcome these weaknesses is antioxidant biosensor based on superoxide dismutase (SOD) enzyme. Therefore, this study was carried out to measure the SOD activity originating from Deinococcus radiodurans and to determine its kinetics properties. Carbon paste electrode modified with ferrocene and immobilized SOD exhibited anode and cathode current peak at potential of +400 and +300mv respectively, in both pure SOD and SOD of D. radiodurans. This indicated that the current generated was from superoxide catalytic dismutation reaction by SOD. Optimum conditions for SOD activity was at pH 9 and temperature of 27.50C for D. radiodurans SOD, and pH 11 and temperature of 200C for pure SOD. Dismutation reaction kinetics of superoxide catalyzed by SOD followed the Lineweaver-Burk kinetics with D. radiodurans SOD KMapp value was smaller than pure SOD. The result showed that D. radiodurans SOD had higher enzyme-substrate affinity and specificity than pure SOD. It concluded that D. radiodurans SOD had a great potential as biological recognition component for antioxidant biosensor.
Abstract: Global temperature had increased by about 0.5oC over
the past century, increasing temperature leads to a loss or a decrease
of soil organic matter (SOM). Whereas soil organic matter in many
tropical soils is less stable than that of temperate soils, and it will be
easily affected by climate change. Therefore, conservation of soil
organic matter is urgent issue nowadays. This paper presents the
effect of different doses (5%, 15%) of Ca-type zeolite in conjunction
with organic manure, applied to soil samples from Philippines,
Paraguay and Japan, on the decomposition resistance of soil organic
matter under high temperature. Results showed that a remain or
slightly increase the C/N ratio of soil. There are an increase in
percent of humic acid (PQ) that extracted with Na4P2O7. A decrease
of percent of free humus (fH) after incubation was determined. A
larger the relative color intensity (RF) value and a lower the color
coefficient (6logK) value following increasing zeolite rates leading
to a higher degrees of humification. The increase in the aromatic
condensation of humic acid (HA) after incubation, as indicates by the
decrease of H/C and O/C ratios of HA. This finding indicates that the
use of zeolite could be beneficial with respect to SOM conservation
under global warming condition.
Abstract: Beginning from the creator of integro-differential
equations Volterra, many scientists have investigated these
equations. Classic method for solving integro-differential
equations is the quadratures method that is successfully applied up
today. Unlike these methods, Makroglou applied hybrid methods
that are modified and generalized in this paper and applied to the
numerical solution of Volterra integro-differential equations. The
way for defining the coefficients of the suggested method is also
given.
Abstract: Due to dynamic evolution, the ability of a
manufacturing technology to produce a special product is changing.
Therefore, it is essential to monitor the established techniques and
processes to detect whether a company-s production will fit future
circumstances. Concerning the manufacturing technology planning
process, companies must decide when to change to a new technology
for maintaining and increasing competitive advantages. In this
context, the maturity assessment of the focused technologies is
crucial. This article presents an approach for defining the maturity of
a manufacturing technology from a strategic point of view. The
concept is based on the approach of technology readiness level
(TRL) according to NASA (National Aeronautics and Space
Administration), but also includes dynamic changes. Therefore, the
model takes into account the concept of the technology life cycle.
Furthermore, it enables a company to estimate the ideal date for
implementation of a new manufacturing technology.
Abstract: This study investigated the effect of oxygen and
micro-cracking on the flotation of low grade nickel sulphide ore. The
ore treated contained serpentine minerals which have a history of
being difficult to process efficiently. The use of oxygen as a bubbling
gas has been noted to be effective because it increases the pulp
potential. The desired effect of micro cracking the ore is that the
nickel sulphide minerals will become activated and this activation
will render these minerals more susceptible to react with potassium
amyl xanthate collectors, resulting in a higher recovery of nickel and
hinder the recovery of other undesired minerals contained in the ore.
Higher nickel recoveries were obtained when pure oxygen was used
as a bubbling gas rather than the conventional air. Microwave
cracking favored the recovery of nickel.
Abstract: Axial Flux Permanent Magnet (AFPM) Machines require effective cooling due to their high power density. The detrimental effects of overheating such as degradation of the insulation materials, magnets demagnetization, and increase of Joule losses are well known. This paper describes the CFD simulations performed on a test rig model of an air cooled Axial Flux Permanent Magnet (AFPM) generator built at Durham University to identify the temperatures and heat transfer coefficient on the stator. The Reynolds Averaged Navier-Stokes and the Energy equations are solved and the flow pattern and heat transfer developing inside the machine are described. The Nusselt number on the stator surfaces has been found. The dependency of the heat transfer on the flow field is described temperature field obtained. Tests on an experimental are undergoing in order to validate the CFD results.
Abstract: Boron minerals are very useful for various industrial
activities, such as glass industry and detergent industry, due to its
mechanical and chemical properties. During the production of boron
compounds, many of these are introduced into the environment in the
form of waste. Boron is also an important micro nutrient for the
plants to vegetate but if it exists in high concentrations, it could have
toxic effects. The maximum boron level in drinking water for human
health is given as 0.3 mg/L in World Health Organization (WHO)
standards. The toxic effects of boron should be noted especially for
dry regions, thus, in recent years, increasing attention has been paid
to remove the boron from waste waters. In this study, boron removal
is implemented by ion exchange process using Amberlite IRA-743
resin. Amberlite IRA-743 resin is a boron specific resin and it
belongs to the polymerizate sorbent group within the aminopolyol
functional group. Batch studies were performed to investigate the
effects of various experimental parameters, such as adsorbent dose,
initial concentration and pH, on the removal of boron. It is found
that, when the adsorbent dose increases removal of boron from the
liquid phase increases. However, an increase in the initial
concentration decreases the removal of boron. The effective pH
values for removal of boron are determined between 8.5 and 9.
Equilibrium isotherms were also analyzed by Langmuir and
Freundlich isotherm models. The Langmuir isotherm is obeyed better
than the Freundlich isotherm.
Abstract: This study investigated the removal efficiency of electrokinetic remediation of copper-contaminated soil at different combinations of enhancement reagents used as anolyte and catholyte. Sodium hydroxide (at 0.1, 0.5, and 1.0 M concentrations) and distilled water were used as anolyte, while lactic acid (at 0.01, 0.1, and 0.5 M concentrations), ammonium citrate (also at 0.01, 0.1, and 0.5 M concentrations) and distilled water were used as catholyte. A continuous voltage application (1.0 VDC/cm) was employed for 240 hours for each experiment. The copper content of the catholyte was determined at the end of the 240-hour period. Optimization was carried out with a Response Surface Methodology - Optimal Design, including F test, and multiple comparison method, to determine which pair of anolyte-catholyte was the most significant for the removal efficiency. "1.0 M NaOH" was found to be the most significant anolyte while it was established that lactic acid was the most significant type of catholyte to be used for the most successful electrokinetic experiments. Concentrations of lactic acid should be at the range of 0.1 M to 0.5 M to achieve maximum percent removal values.
Abstract: In countries with hot climates, air-conditioning forms
a large proportion of annual peak electrical demand, requiring
expansion of power plants to meet the peak demand, which goes
unused most of the time. Use of well-designed cool storage can offset
the peak demand to a large extent. In this study, an air conditioning
system with naturally stratified storage tank was designed,
constructed and tested. A new type of diffuser was designed and used
in this study. Factors that influence the performance of chilled water
storage tanks were investigated. The results indicated that stratified
storage tank consistently stratified well without any physical barrier.
Investigation also showed that storage efficiency decreased with
increasing flow rate due to increased mixing of warm and chilled
water. Diffuser design and layout primarily affected the mixing near
the inlet diffuser and the extent of this mixing had primary influence
on the shape of the thermocline. The heat conduction through tank
walls and through the thermocline caused widening of mixed volume.
Thermal efficiency of stratified storage tanks was as high as 90
percent, which indicates that stratified tanks can effectively be used
as a load management technique.
Abstract: Due to the low heavy metal concentrations, the
bottom ash from a 32 MW municipal district heating plant was
determined to be a potential forest fertilizer as such. However,
additional Ca would be needed, because its Ca concentration of 1.9-
% (d.w.) was lower than the statutory Finnish minimum limit value
of 6.0-% (d.w.) for Ca in forest fertilizer. Due to the elevated As
concentration (53.0 mg/kg; d.w.) in the fly ash from the 32 MW
municipal district heating plant, and Cr concentration (620 mg/kg;
d.w.) in the ash fraction (i.e. mixture of the bottom ash and fly ash)
from the 6 MW municipal district heating plant, which exceed the
limit values of 30 mg/kg (d.w.) and 300 mg/kg (d.w.) for As and Cr,
respectively, these residues are not suitable as forest fertilizers.
Although these ash fractions cannot be used as a forest fertilizer as
such, they can be used for the landscaping of landfills or in industrial
and other areas that are closed to the public. However, an
environmental permit is then needed.
Abstract: In today-s modern world, the number of vehicles is
increasing on the road. This causes more people to choose walking
instead of traveling using vehicles. Thus, proper planning of
pedestrians- paths is important to ensure the safety of pedestrians in a
walking area. Crowd dynamics study the pedestrians- behavior and
modeling pedestrians- movement to ensure safety in their walking paths.
To date, many models have been designed to ease pedestrians-
movement. The Social Force Model is widely used among researchers
as it is simpler and provides better simulation results. We will discuss
the problem regarding the ritual of circumambulating the Ka-aba
(Tawaf) where the entrances to this area are usually congested which
worsens during the Hajj season. We will use the computer simulation
model SimWalk which is based on the Social Force Model to simulate
the movement of pilgrims in the Tawaf area. We will first discuss the
effect of uni and bi-directional flows at the gates. We will then restrict
certain gates to the area as the entrances only and others as exits only.
From the simulations, we will study the effect of the distance of other
entrances from the beginning line and their effects on the duration of
pilgrims circumambulate Ka-aba. We will distribute the pilgrims at the
different entrances evenly so that the congestion at the entrances can be
reduced. We would also discuss the various locations and designs of
barriers at the exits and its effect on the time taken for the pilgrims to
exit the Tawaf area.
Abstract: State tax revenues in most countries started to decrease during the recession. Government of Latvia decided to compensate the decline by increasing rates of several taxes including excise tax on strong alcohol. The total increase in 2009 constituted 42% and the rate increased from 896€ to 1 266€ for 100l of absolute alcohol. Since then this has had a negative impact on consumption volumes and the split between legal and illegal market. The legal alcohol sales decreased by almost 50% (by volume), consequentially having negative effect on the State revenues from VAT and excise tax. Estimated results for 2010 are indicating 54 million € decrease in VAT, excise tax and other taxes versus 2008 (excise tax -19 million €, VAT -30 million €, other taxes -5 million €). The paper aims to analyze impact of the increase in excise tax on consumption patterns, State revenues and competitiveness of the local companies to draw up proposals for the state authorities regarding more effective tax policies. The analysis reveals a relationship between excise tax rate, illegal alcohol market and State revenues. The results can be used to improve excise tax system and effectiveness in Latvia.
Abstract: Segmentation of Magnetic Resonance Imaging (MRI) images is the most challenging problems in medical imaging. This paper compares the performances of Seed-Based Region Growing (SBRG), Adaptive Network-Based Fuzzy Inference System (ANFIS) and Fuzzy c-Means (FCM) in brain abnormalities segmentation. Controlled experimental data is used, which designed in such a way that prior knowledge of the size of the abnormalities are known. This is done by cutting various sizes of abnormalities and pasting it onto normal brain tissues. The normal tissues or the background are divided into three different categories. The segmentation is done with fifty seven data of each category. The knowledge of the size of the abnormalities by the number of pixels are then compared with segmentation results of three techniques proposed. It was proven that the ANFIS returns the best segmentation performances in light abnormalities, whereas the SBRG on the other hand performed well in dark abnormalities segmentation.
Abstract: This paper presents and discusses the numerical simulations of transient laminar natural convection cooling of high Prandtl number fluids in cubical cavities, in which the six walls of the cavity are subjected to a step change in temperature. The effect of the fluid Prandtl number on the heat transfer coefficient is studied for three different fluids (Golden Syrup, Glycerin and Glycerin-water solution 50%). The simulations are performed at two different Rayleigh numbers (5·106 and 5·107) and six different Prandtl numbers (3 · 105 ≥Pr≥ 50). Heat conduction through the cavity glass walls is also considered. The propsed correlations of the averaged heat transfer coefficient (N u) showed that it is dependant on the initial Ra and almost independent on P r. The instantaneous flow patterns, temperature contours and time evolution of volume averaged temperature and heat transfer coefficient are presented and analyzed.
Abstract: The bag radius of the nucleon can be determined by MIT bag model based on electric and magnetic form factors of the nucleon. Also we determined the masses and magnetic moment of the nucleon with MIT bag model, using bag radius and compared with other results, suggests a suitable compatibility.
Abstract: Partial coherence between two signals removing the contribution of a periodic, deterministic signal is proposed for evaluating the interrelationship in multivariate systems. The estimator expression was derived and shown to be independent of such periodic signal. Simulations were used for obtaining its critical value, which were found to be the same as those for Gaussian signals, as well as for evaluating the technique. An Illustration with eletroencephalografic (EEG) signals during photic stimulation is also provided. The application of the proposed technique in both simulation and real EEG data indicate that it seems to be very specific in removing the contribution of periodic sources. The estimate independence of the periodic signal may widen partial coherence application to signal analysis, since it could be used together with simple coherence to test for contamination in signals by a common, periodic noise source.
Abstract: This paper emphasizes on the application of genetic algorithm (GA) to optimize the parameters of the TMD for achieving the best results in the reduction of the building response under earthquake excitations. The Integral of the Time multiplied Absolute value of the Error (ITAE) based on relative displacement of all floors in the building is taken as a performance index of the optimization criterion. The problem of robustly TMD controller design is formatted as an optimization problem based on the ITAE performance index to be solved using GA that has a story ability to find the most optimistic results. An 11–story realistic building, located in the city of Rasht, Iran is considered as a test system to demonstrate effectiveness of the proposed GA based TMD (GATMD) controller without specifying which mode should be controlled. The results of the proposed GATMD controller are compared with the uncontrolled structure through timedomain simulation and some performance indices. The results analysis reveals that the designed GA based TMD controller has an excellent capability in reduction of the seismically excited example building and the ITAE performance, that is so for remains as unknown, can be introduced a new criteria - method for structural dynamic design.
Abstract: Modes of occurrence of Pb, As, Cr, Co, Cu, and Ni in bituminous coal and lignite were determined by means of sequential extraction using NH4OAc, HCl, HF and HNO3 extraction solutions. Elemental affinities obtained were then evaluated in relation to volatility of these elements during the combustion of these coals in two circulating fluidised-bed power stations. It was found out that higher percentage of the elements bound in silicates brought about lower volatility, while higher elemental proportion with monosulphides association (or bound as exchangeable ion) resulted in higher volatility. The only exception was the behavior of arsenic, whose volatility depended on amount of limestone added during the combustion process (as desulphurisation additive) rather than to its association in coal.
Abstract: We present a theory for optimal filtering of infinite sets of random signals. There are several new distinctive features of the proposed approach. First, we provide a single optimal filter for processing any signal from a given infinite signal set. Second, the filter is presented in the special form of a sum with p terms where each term is represented as a combination of three operations. Each operation is a special stage of the filtering aimed at facilitating the associated numerical work. Third, an iterative scheme is implemented into the filter structure to provide an improvement in the filter performance at each step of the scheme. The final step of the concerns signal compression and decompression. This step is based on the solution of a new rank-constrained matrix approximation problem. The solution to the matrix problem is described in this paper. A rigorous error analysis is given for the new filter.