Abstract: The paper is focused on the identification of limiting
environmental factors of individual industrial floors on which newly
developed polymer protection and repair systems with the use of
secondary raw materials will be used. These mainly include floors
with extreme stresses and special requirements for materials used. In
relation to the environment of a particular industrial floor, it is
necessary to ensure, for example, chemical stability, resistance to
higher temperatures, resistance to higher mechanical stress, etc. for
developed materials, which is reflected in the demands for the
developed material systems. The paper describes individual
environments and, in relation to them, also requirements for
individual components of the developed materials and for the
developed materials as a whole.
Abstract: By textile science incorporating with electronic
industry, developed textile products start to take part in different
areas such as industry, military, space, medical etc. for health,
protection, defense, communication and automation. Electronic
textiles (e-textiles) are fabrics that contain electronics and
interconnections with them. In this study, two types of base yarns
(cotton and acrylic) and three types of conductive steel yarns with
different linear resistance values (14Ω/m, 30Ω/m, 70Ω/m) were used
to investigate the effect of base yarn type and linear resistance of
conductive yarns on thermal behavior of e-textile structures. Thermal
behavior of samples was examined by thermal camera.
Abstract: Control of honey frauds is needed in Ecuador to
protect bee keepers and consumers because simple syrups and new
syrups with eucalyptus are sold as genuine honeys. Authenticity of
Ecuadorian commercial honeys was tested with a vortex emulsion
consisting on one volume of honey:water (1:1) dilution, and two
volumes of diethyl ether. This method allows a separation of phases
in one minute to discriminate genuine honeys that form three phase
and fake honeys that form two phases; 34 of the 42 honeys analyzed
from five provinces of Ecuador were genuine. This was confirmed
with 1H NMR spectra of honey dilutions in deuterated water with an
enhanced amino acid region with signals for proline, phenylalanine
and tyrosine. Classic quality indicators were also tested with this
method (sugars, HMF), indicators of fermentation (ethanol, acetic
acid), and residues of citric acid used in the syrup manufacture. One
of the honeys gave a false positive for genuine, being an admixture of
genuine honey with added syrup, evident for the high sucrose.
Sensory analysis was the final confirmation to recognize the honey
groups studied here, namely honey produced in combs by Apis
mellifera, fake honey, and honey produced in cerumen pots by
Geotrigona, Melipona, and Scaptotrigona. Chloroform extractions of
honey were also done to search lipophilic additives in NMR spectra.
This is a valuable contribution to protect honey consumers, and to
develop the beekeeping industry in Ecuador.
Abstract: All the software engineering researches and best
industry practices aim at providing software products with high
degree of quality and functionality at low cost and less time. These
requirements are addressed by the Component Based Software
Engineering (CBSE) as well. CBSE, which deals with the software
construction by components’ assembly, is a revolutionary extension
of Software Engineering. CBSE must define and describe processes
to assure timely completion of high quality software systems that are
composed of a variety of pre built software components. Though
these features provide distinct and visible benefits in software design
and programming, they also raise some challenging problems. The
aim of this work is to summarize the pertinent issues and
considerations in CBSE to make an understanding in forms of
concepts and observations that may lead to development of newer
ways of dealing with the problems and challenges in CBSE.
Abstract: In our research we aimed to test a managerial
approach for the fuzzy front end (FFE) of innovation by creating
controlled experiment/ business case in a breakthrough innovation
development. The experiment was in the sport industry and covered
all aspects of the customer discovery stage from ideation to
prototyping followed by patent application. In the paper we describe
and analyze mile stones, tasks, management challenges, decisions
made to create the break through innovation, evaluate overall
managerial efficiency that was at the considered FFE stage.
We set managerial outcome of the FFE stage as a valid product
concept in hand. In our paper we introduce hypothetical construct
“Q-factor” that helps us in the experiment to distinguish quality of
FFE outcomes.
The experiment simulated for entrepreneur the FFE of innovation
and put on his shoulders responsibility for the outcome of valid
product concept. While developing managerial approach to reach the
outcome there was a decision to look on product concept from the
cognitive psychology and cognitive science point of view. This view
helped us to develop the profile of a person whose projection (mental
representation) of a new product could optimize for a manager or
entrepreneur FFE activities. In the experiment this profile was tested
to develop breakthrough innovation for swimmers. Following the
managerial approach the product concept was created to help
swimmers to feel/sense water. The working prototype was developed
to estimate the product concept validity and value added effect for
customers.
Based on feedback from coachers and swimmers there were strong
positive effect that gave high value for customers, and for the
experiment – the valid product concept being developed by proposed
managerial approach for the FFE.
In conclusions there is a suggestion of managerial approach that
was derived from experiment.
Abstract: The textile industry plays a major role in the economy
of India and on the other side of the coin it is the major source for
water pollution. As azo dyes is the largest dye class they are
extensively used in many fields such as textile industry, leather
tanning industry, paper production, food, color photography,
pharmaceuticals and medicine, cosmetic, hair colorings, wood
staining, agricultural, biological and chemical research etc. In
addition to these, they can have acute and/or chronic effects on
organisms depending on their concentration and length of exposure
when they discharged as effluent in the environment. The aim of this
study was to assess the genotoxic and histotoxic potentials of
environmentally relevant concentrations of C. I. Reactive Red 120
(RR 120) on Catla catla, important edible freshwater fingerlings. For
this, healthy Catla catla fingerlings were procured from the
Government Fish Farm and acclimatized in 100 L capacity and
continuously aerated glass aquarium in laboratory for 15 days.
According to APHA some physic-chemical parameters were
measured and maintained such as temperature, pH, dissolve oxygen,
alkalinity, total hardness. Water along with excreta had been changed
every 24 hrs. All fingerlings were fed artificial food palates once a
day @ body weight. After 15 days fingerlings were grouped in 5 (10
in each) and exposed to various concentrations of RR 120 (Control,
10, 20, 30 and 40 mg.l-1) and samples (peripheral blood and gills,
kidney) were collected and analyzed at 96 hrs. All results were
compared with the control. Micronuclei (MN), nuclear buds (NB),
fragmented-apoptotic (FA) and bi-nucleated (BN) cells in blood
smears and in tissues (gills and kidney cells) were observed.
Prominent histopathological alterations were noticed in gills such as
aneurism, hyperplasia, degenerated central axis, lifting of gill
epithelium, curved secondary gill lamellae etc. Similarly kidney
showed some detrimental changes like shrunken glomeruli with
increased periglomerular space, degenerated renal tubules etc. Both
haematological and histopathological changes clearly reveal the toxic
potential of RR 120. This work concludes that water pollution
assessment can be done by these two biomarkers which provide
baseline to the further chromosomal or molecular work.
Abstract: Verification of vented wooden façade system with
bonded joints is presented in this paper. The potential of bonded
joints is studied and described in more detail. The paper presents the results of an experimental and theoretical research about the effects of freeze cycling on the bonded joint. For the purpose of tests spruce
timber profiles were chosen for the load bearing substructure. Planks from wooden plastic composite and Siberian larch are representing facade cladding. Two types of industrial polyurethane adhesives intended for structural bonding were selected. The article is focused on the preparation as well as on the subsequent curing and conditioning of test samples. All test samples were subjected to 15 cycles that represents sudden temperature changes, i.e. immersion in a water bath at (293.15 ± 3) K for 6 hours and subsequent freezing to (253.15 ± 2) K for 18 hours. Furthermore, the retention of bond strength between substructure and cladding wastested and strength in shear was determined under tensile stress.Research data indicate that little, if any, damage to the bond results from freezingcycles. Additionally, the suitability of selected group of adhesives in combination with timber substructure was confirmed.
Abstract: The biodegradable family of polymers
polyhydroxyalkanoates is an interesting substitute for convectional
fossil-based plastics. However, the manufacturing and environmental
impacts associated with their production via intracellular bacterial
fermentation are strongly dependent on the raw material used and on
energy consumption during the extraction process, limiting their
potential for commercialization. Industrial wastewater is studied in
this paper as a promising alternative feedstock for waste valorization.
Based on results from laboratory and pilot-scale experiments, a
conceptual process design, techno-economic analysis and life cycle
assessment are developed for the large-scale production of the most
common type of polyhydroxyalkanoate, polyhydroxbutyrate.
Intracellular polyhydroxybutyrate is obtained via fermentation of
microbial community present in industrial wastewater and the
downstream processing is based on chemical digestion with
surfactant and hypochlorite. The economic potential and
environmental performance results help identifying bottlenecks and
best opportunities to scale-up the process prior to industrial
implementation. The outcome of this research indicates that the
fermentation of wastewater towards PHB presents advantages
compared to traditional PHAs production from sugars because the
null environmental burdens and financial costs of the raw material in
the bioplastic production process. Nevertheless, process optimization
is still required to compete with the petrochemicals counterparts.
Abstract: The construction industry has been demonstrating
increased growth and importance in Brazil’s national economic
development. This study aims to evaluate the financial performance
of the leading companies in the construction sector in Brazil in the
period from 2009 to 2012. An analysis is made of the capital
structure, liquidity, and profitability of the six largest companies in
the construction sector in Brazil: Brookfield, Cyrela, Gafisa, MRV,
PDG and Rossi. The results are then compared with standard industry
ratios. It was found that among the companies analyzed, MRV and
Cyrela showed the best relative performance in the period under
consideration.
Abstract: Co-crystal is believed to improve the solubility and
dissolution rates and thus, enhanced the bioavailability of poor water
soluble drugs particularly during the oral route of administration.
With the existing of poorly soluble drugs in pharmaceutical industry,
the screening of co-crystal formation using carbamazepine (CBZ) as
a model drug compound with dicarboxylic acids co-crystal formers
(CCF) namely fumaric (FA) and succinic (SA) acids in ethanol has
been studied. The co-crystal formations were studied by varying the
mol ratio values of CCF to CBZ to access the effect of CCF
concentration on the formation of the co-crystal. Solvent evaporation,
slurry and cooling crystallization which representing the solution
based method co-crystal screening were used. Based on the
differential scanning calorimetry (DSC) analysis, the melting point of
CBZ-SA in different ratio was in the range between 188oC-189oC.
For CBZ-FA form A and CBZ-FA form B the melting point in
different ratio were in the range of 174oC-175oC and 185oC-186oC
respectively. The product crystal from the screening was also
characterized using X-ray powder diffraction (XRPD). The XRPD
pattern profile analysis has shown that the CBZ co-crystals with FA
and SA were successfully formed for all ratios studied. The findings
revealed that CBZ-FA co-crystal were formed in two different
polymorphs. It was found that CBZ-FA form A and form B were
formed from evaporation and slurry crystallization methods
respectively. On the other hand, in cooling crystallization method,
CBZ-FA form A was formed at lower mol ratio of CCF to CBZ and
vice versa. This study disclosed that different methods and mol ratios
during the co-crystal screening can affect the outcome of co-crystal
produced such as polymorphic forms of co-crystal and thereof. Thus,
it was suggested that careful attentions is needed during the screening
since the co-crystal formation is currently one of the promising
approach to be considered in research and development for
pharmaceutical industry to improve the poorly soluble drugs.
Abstract: The arm length, hand length, hand breadth and middle
finger length of 1540 right-handed industrial workers of Haryana
state was used to assess the relationship between the upper limb
dimensions and stature. Initially, the data were analyzed using basic
univariate analysis and independent t-tests; then simple and multiple
linear regression models were used to estimate stature using SPSS
(version 17). There was a positive correlation between upper limb
measurements (hand length, hand breadth, arm length and middle
finger length) and stature (p < 0.01), which was highest for hand
length. The accuracy of stature prediction ranged from ± 54.897 mm
to ± 58.307 mm. The use of multiple regression equations gave better
results than simple regression equations. This study provides new
forensic standards for stature estimation from the upper limb
measurements of male industrial workers of Haryana (India). The
results of this research indicate that stature can be determined using
hand dimensions with accuracy, when only upper limb is available
due to any reasons likewise explosions, train/plane crashes, mutilated
bodies, etc. The regression formula derived in this study will be
useful for anatomists, archaeologists, anthropologists, design
engineers and forensic scientists for fairly prediction of stature using
regression equations.
Abstract: Cloud computing is a new technology in industry and
academia. The technology has grown and matured in last half decade
and proven their significant role in changing environment of IT
infrastructure where cloud services and resources are offered over the
network. Cloud technology enables users to use services and
resources without being concerned about the technical implications of
technology. There are substantial research work has been performed
for the usage of cloud computing in educational institutes and
majority of them provides cloud services over high-end blade servers
or other high-end CPUs. However, this paper proposes a new stack
called “CiCKAStack” which provide cloud services over unutilized
computing resources, named as commodity computers.
“CiCKAStack” provides IaaS and PaaS using underlying commodity
computers. This will not only increasing the utilization of existing
computing resources but also provide organize file system, on
demand computing resource and design and development
environment.
Abstract: Applications of the Hausdorff space and its mappings
into tangent spaces are outlined, including their fractal dimensions
and self-similarities. The paper details this theory set up and further
describes virtualizations and atomization of manufacturing processes.
It demonstrates novel concurrency principles that will guide
manufacturing processes and resources configurations. Moreover,
varying levels of details may be produced by up folding and breaking
down of newly introduced generic models. This choice of layered
generic models for units and systems aspects along specific aspects
allows research work in parallel to other disciplines with the same
focus on all levels of detail. More credit and easier access are granted
to outside disciplines for enriching manufacturing grounds. Specific
mappings and the layers give hints for chances for interdisciplinary
outcomes and may highlight more details for interoperability
standards, as already worked on the international level. The new rules
are described, which require additional properties concerning all
involved entities for defining distributed decision cycles, again on the
base of self-similarity. All properties are further detailed and assigned
to a maturity scale, eventually displaying the smartness maturity of a
total shopfloor or a factory. The paper contributes to the intensive
ongoing discussion in the field of intelligent distributed
manufacturing and promotes solid concepts for implementations of
Cyber Physical Systems and the Internet of Things into
manufacturing industry, like industry 4.0, as discussed in German-speaking
countries.
Abstract: Using the first-principles full-potential linearized
augmented plane wave plus local orbital (FP-LAPW+lo) method
based on density functional theory (DFT), we have investigated the
electronic structure and magnetism of full Heusler alloys Co2ZrGe
and Co2NbB. These compounds are predicted to be half-metallic
ferromagnets (HMFs) with a total magnetic moment of 2.000 B per
formula unit, well consistent with the Slater-Pauling rule.
Calculations show that both the alloys have an indirect band gaps, in
the minority-spin channel of density of states (DOS), with values of
0.58 eV and 0.47 eV for Co2ZrGe and Co2NbB, respectively.
Analysis of the DOS and magnetic moments indicates that their
magnetism is mainly related to the d-d hybridization between the Co
and Zr (or Nb) atoms. The half-metallicity is found to be relatively
robust against volume changes. In addition, an atom inside molecule
AIM formalism and an electron localization function ELF were also
adopted to study the bonding properties of these compounds, building
a bridge between their electronic and bonding behavior.
As they have a good crystallographic compatibility with the lattice of
semiconductors used industrially and negative calculated cohesive
energies with considerable absolute values these two alloys could be
promising magnetic materials in the spintronic field.
Abstract: Machining of hard materials is a recent technology for
direct production of work-pieces. The primary challenge in
machining these materials is selection of cutting tool inserts which
facilitates an extended tool life and high-precision machining of the
component. These materials are widely for making precision parts for
the aerospace industry. Nickel-based alloys are typically used in
extreme environment applications where a combination of strength,
corrosion resistance and oxidation resistance material characteristics
are required. The present paper reports the theoretical and
experimental investigations carried out to understand the influence of
machining parameters on the response parameters. Considering the
basic machining parameters (speed, feed and depth of cut) a study has
been conducted to observe their influence on material removal rate,
surface roughness, cutting forces and corresponding tool wear.
Experiments are designed and conducted with the help of Central
Composite Rotatable Design technique. The results reveals that for a
given range of process parameters, material removal rate is favorable
for higher depths of cut and low feed rate for cutting forces. Low feed
rates and high values of rotational speeds are suitable for better finish
and higher tool life.
Abstract: Beta-glucosidase, chitinase, leucine-aminopeptidase, acid phosphomonoesterase and acetate-esterase enzyme activities in
the soils under the impact of metallurgical industrial activity in Lori
marz (district) were investigated. The results of the study showed that
the activities of the investigated enzymes in the soils decreased with increasing distance from the Shamlugh copper mine, the Chochkan
tailings storage facility and the ore transportation road. Statistical
analysis revealed that the activities of the enzymes were positively
correlated (significant) to each other according to the observation
sites which indicated that enzyme activities were affected by the
same anthropogenic factor. The investigations showed that the soils
were polluted with heavy metals (Cu, Pb, As, Co, Ni, Zn) due to
copper mining activity in this territory. The results of Pearson
correlation analysis revealed a significant negative correlation
between heavy metal pollution degree (Nemerow integrated pollution
index) and soil enzyme activity. All of this indicated that copper
mining activity in this territory causing the heavy metal pollution of
the soils resulted in the inhabitation of the activities of the enzymes
which are considered as biological catalysts to decompose organic
materials and facilitate the cycling of nutrients.
Abstract: Within the framework of this research, the regulatory
documents, which are in force in relation to this industry, were
analyzed. The main attention is turned to their modernization and
necessity of their compliance with European standards.
It is a current issue to direct the efforts of state policy on support
of business by implementing infrastructural projects, as well as by
development of human resources, which may be possible by
supporting the relevant higher and vocational studying-educational
programs.
Abstract: Information technology and information systems are
currently at a tipping point. The digital age fundamentally transforms
a large number of industries in the ways they work. Lines between
business and technology blur. Researchers have acknowledged that
this is the time in which the IT/IS organisation needs to re-strategize
itself. In this paper, the author provides a structured review of the IS
and organisation design literature addressing the question of how the
digital age changes the design categories of an IT/IS organisation
design. The findings show that most papers just analyse single
aspects of either IT/IS relevant information or generic organisation
design elements but miss a holistic ‘big-picture’ onto an IT/IS
organisation design. This paper creates a holistic IT/IS organisation
design framework bringing together the IS research strand, the digital
strand and the generic organisation design strand. The research
identified four IT/IS organisation design categories (strategy,
structure, processes and people) and discusses the importance of two
additional categories (sourcing and governance). The authors findings
point to a first anchor point from which further research needs to be
conducted to develop a holistic IT/IS organisation design framework.
Abstract: Data mining idea is mounting rapidly in admiration
and also in their popularity. The foremost aspire of data mining
method is to extract data from a huge data set into several forms that
could be comprehended for additional use. The data mining is a
technology that contains with rich potential resources which could be
supportive for industries and businesses that pay attention to collect
the necessary information of the data to discover their customer’s
performances. For extracting data there are several methods are
available such as Classification, Clustering, Association,
Discovering, and Visualization… etc., which has its individual and
diverse algorithms towards the effort to fit an appropriate model to
the data. STATISTICA mostly deals with excessive groups of data
that imposes vast rigorous computational constraints. These results
trials challenge cause the emergence of powerful STATISTICA Data
Mining technologies. In this survey an overview of the STATISTICA
software is illustrated along with their significant features.
Abstract: This paper is focusing on the attitude of Georgian
consumers toward social media, influence of social media on
consumer buying behavior. The purpose of this paper is to explore
the usage of social media marketing for small business companies of
Georgia. The result of marketing research has revealed that social
webs are mostly used by Georgian consumers, but they have little
impact on the buying decision. The research method was exploratory
and descriptive. Conclusions summarize the research results and
offers insight to provide better understandings of consumers demand
and implementation of marketing strategy through social media in
Georgia.