Abstract: This paper presents a new method of fault detection and isolation (FDI) for polymer electrolyte membrane (PEM) fuel cell (FC) dynamic systems under an open-loop scheme. This method uses a radial basis function (RBF) neural network to perform fault identification, classification and isolation. The novelty is that the RBF model of independent mode is used to predict the future outputs of the FC stack. One actuator fault, one component fault and three sensor faults have been introduced to the PEMFC systems experience faults between -7% to +10% of fault size in real-time operation. To validate the results, a benchmark model developed by Michigan University is used in the simulation to investigate the effect of these five faults. The developed independent RBF model is tested on MATLAB R2009a/Simulink environment. The simulation results confirm the effectiveness of the proposed method for FDI under an open-loop condition. By using this method, the RBF networks able to detect and isolate all five faults accordingly and accurately.
Abstract: A conjugate heat transfer for steady two-dimensional
mixed convection with magnetic hydrodynamic (MHD) flow of an
incompressible quiescent fluid over an unsteady thermal forming
stretching sheet has been studied. A parameter, M, which is used to
represent the dominance of the magnetic effect has been presented in
governing equations. The similar transformation and an implicit
finite-difference method have been used to analyze the present
problem. The numerical solutions of the flow velocity distributions,
temperature profiles, the wall unknown values of f''(0) and '(θ (0) for
calculating the heat transfer of the similar boundary-layer flow are
carried out as functions of the unsteadiness parameter (S), the Prandtl
number (Pr), the space-dependent parameter (A) and
temperature-dependent parameter (B) for heat source/sink and the
magnetic parameter (M). The effects of these parameters have also
discussed. At the results, it will produce greater heat transfer effect
with a larger Pr and M, S, A, B will reduce heat transfer effects. At
last, conjugate heat transfer for the free convection with a larger G has
a good heat transfer effect better than a smaller G=0.
Abstract: In recent years the large scale use of the power electronic equipment has led to an increase of harmonics in the power system. The harmonics results into a poor power quality and have great adverse economical impact on the utilities and customers. Current harmonics are one of the most common power quality problems and are usually resolved by using shunt active filter (SHAF). The main objective of this work is to develop PI and Fuzzy logic controllers (FLC) to analyze the performance of Shunt Active Filter for mitigating current harmonics under balanced and unbalanced sinusoidal source voltage conditions for normal load and increased load. When the supply voltages are ideal (balanced), both PI and FLC are converging to the same compensation characteristics. However, the supply voltages are non-ideal (unbalanced), FLC offers outstanding results. Simulation results validate the superiority of FLC with triangular membership function over the PI controller.
Abstract: Experiments with pumpkin-rowanberry marmalade
candies were carried out at the Faculty of Food Technology of the
Latvia University of Agriculture. The objective of this investigation
was to evaluate the quality changes of pumpkin-rowanberry
marmalade candies packed in different packaging materials during
the storage of 15 weeks, and to find the most suitable packaging
material for prolongation of low sugar marmalade candies shelf-life.
An active packaging in combination with modified atmosphere
(MAP, CO2 100%) was examined and compared with traditional
packaging in air ambiance. Polymer Multibarrier 60 and paper bags
were used. Influence of iron based oxygen absorber in sachets of 500
cc obtained from Mitsubishi Gas Chemical Europe Ageless® on the
marmalade candies’ quality was tested during shelf life. Samples of
80±5 g were packaged in polymer pouches (110 mm x 110 mm),
hermetically sealed by MULTIVAC C300 vacuum chamber machine,
and stored in a room temperature +21±0.5 °C. The physiochemical
properties –moisture content, hardness, aw, pH, changes of
atmosphere content (CO2 and O2), ascorbic acid, total carotenoids,
total phenols in headspace of packs, and microbial conditions were
analysed before packaging and in the 1st, 3rd , 5th, 8th, 11th and 15th
weeks of storage.
Abstract: Nowadays, the earth is countered with serious problem
of air pollution. This problem has been started from the industrial
revolution and has been faster in recent years, so that leads the earth
to ecological and environmental disaster. One of its results is the
global warming problem and its related increase in global
temperature. The most important factors in air pollution especially in
urban environments are Automobiles and residential buildings that are
the biggest consumers of the fossil energies, so that if the residential
buildings as a big part of the consumers of such energies reduce their
consumption rate, the air pollution will be decreased. Since
Metropolises are the main centers of air pollution in the world,
assessment and analysis of efficient strategies in decreasing air
pollution in such cities, can lead to the desirable and suitable results
and can solve the problem at least in critical level. Tabriz city is one
of the most important metropolises in North west of Iran that about
two million people are living there. for its situation in cold dry
climate, has a high rate of fossil energies consumption that make air
pollution in its urban environment. These two factors, being both
metropolis and in cold dry climate, make this article try to analyze the
strategies of climatic design in old districts of the city and use them in
new districts of the future. These strategies can be used in this city
and other similar cities and pave the way to reduce energy
consumption and related air pollution to save whole world.
Abstract: This paper proposes a novel solution for optimizing
the size and communication overhead of a distributed multiagent
system without compromising the performance. The proposed approach
addresses the challenges of scalability especially when the
multiagent system is large. A modified spectral clustering technique
is used to partition a large network into logically related clusters.
Agents are assigned to monitor dedicated clusters rather than monitor
each device or node. The proposed scalable multiagent system is
implemented using JADE (Java Agent Development Environment)
for a large power system. The performance of the proposed topologyindependent
decentralized multiagent system and the scalable multiagent
system is compared by comprehensively simulating different
fault scenarios. The time taken for reconfiguration, the overall computational
complexity, and the communication overhead incurred are
computed. The results of these simulations show that the proposed
scalable multiagent system uses fewer agents efficiently, makes faster
decisions to reconfigure when a fault occurs, and incurs significantly
less communication overhead.
Abstract: Speed sensorless systems are intensively studied during recent years; this is mainly due to their economical benefit and fragility of mechanical sensors and also the difficulty of installing this type of sensor in many applications. These systems suffer from instability problems and sensitivity to parameter mismatch at low speed operation. In this paper an analysis of adaptive observer stability with stator resistance estimation is given.
Abstract: A numerical study has been carried out to investigate
the heat transfer by natural convection of nanofluid taking Cu as
nanoparticles and the water as based fluid in a three dimensional
annulus enclosure filled with porous media (silica sand) between two
horizontal concentric cylinders with 12 annular fins of 2.4mm
thickness attached to the inner cylinder under steady state conditions.
The governing equations which used are continuity, momentum and
energy equations under an assumptions used Darcy law and
Boussinesq-s approximation which are transformed to dimensionless
equations. The finite difference approach is used to obtain all the
computational results using the MATLAB-7. The parameters affected
on the system are modified Rayleigh number (10 ≤Ra*≤ 1000), fin
length Hf (3, 7 and 11mm), radius ratio Rr (0.293, 0.365 and 0.435)
and the volume fraction(0 ≤ ¤ò ≤ 0 .35). It was found that the
average Nusselt number depends on (Ra*, Hf, Rr and φ). The results
show that, increasing of fin length decreases the heat transfer rate and
for low values of Ra*, decreasing Rr cause to decrease Nu while for
Ra*
greater than 100, decreasing Rr cause to increase Nu and adding
Cu nanoparticles with 0.35 volume fraction cause 27.9%
enhancement in heat transfer. A correlation for Nu in terms of Ra*,
Hf and φ, has been developed for inner hot cylinder.
Abstract: In this paper, an analytical approach for free vibration
analysis of four edges simply supported rectangular Kirchhoff plates
is presented. The method is based on wave approach. From wave
standpoint vibration propagate, reflect and transmit in a structure.
Firstly, the propagation and reflection matrices for plate with simply
supported boundary condition are derived. Then, these matrices are
combined to provide a concise and systematic approach to free
vibration analysis of a simply supported rectangular Kirchhoff plate.
Subsequently, the eigenvalue problem for free vibration of plates is
formulated and the equation of plate natural frequencies is
constructed. Finally, the effectiveness of the approach is shown by
comparison of the results with existing classical solution.
Abstract: The present work demonstrates the design and simulation of a fuzzy control of an air conditioning system at different pressures. The first order Sugeno fuzzy inference system is utilized to model the system and create the controller. In addition, an estimation of the heat transfer rate and water mass flow rate injection into or withdraw from the air conditioning system is determined by the fuzzy IF-THEN rules. The approach starts by generating the input/output data. Then, the subtractive clustering algorithm along with least square estimation (LSE) generates the fuzzy rules that describe the relationship between input/output data. The fuzzy rules are tuned by Adaptive Neuro-Fuzzy Inference System (ANFIS). The results show that when the pressure increases the amount of water flow rate and heat transfer rate decrease within the lower ranges of inlet dry bulb temperatures. On the other hand, and as pressure increases the amount of water flow rate and heat transfer rate increases within the higher ranges of inlet dry bulb temperatures. The inflection in the pressure effect trend occurs at lower temperatures as the inlet air humidity increases.
Abstract: A Rotary Disc Contactor with inner diameter of
9.1cm and maximum operating height of 40cm has been used to
investigate break up phenomenon. Water-Toluene, Water as
continuous phase and Toluene as dispersed phase, was selected as
chemical system in the experiments. The mentioned chemical system
has high interfacial tension so it was possible to form big drops
which permit accurate investigation on break up phenomenon as well
as the first and second critical rotor speeds.
In this study, Break up phenomenon has been studied as a function
of mother drop size, rotor speed and continuous phase height. Further
more; the effects of mother drop size and continuous phase height on
the first and second critical rotor speeds were investigated. Finally,
two modified correlations were proposed to estimate the first and
second critical speeds.
Abstract: The main mission of Ezilla is to provide a friendly
interface to access the virtual machine and quickly deploy the high
performance computing environment. Ezilla has been developed by
Pervasive Computing Team at National Center for High-performance
Computing (NCHC). Ezilla integrates the Cloud middleware,
virtualization technology, and Web-based Operating System (WebOS)
to form a virtual computer in distributed computing environment. In
order to upgrade the dataset and speedup, we proposed the sensor
observation system to deal with a huge amount of data in the
Cassandra database. The sensor observation system is based on the
Ezilla to store sensor raw data into distributed database. We adopt the
Ezilla Cloud service to create virtual machines and login into virtual
machine to deploy the sensor observation system. Integrating the
sensor observation system with Ezilla is to quickly deploy experiment
environment and access a huge amount of data with distributed
database that support the replication mechanism to protect the data
security.
Abstract: Random Oracle Model (ROM) is an effective method
for measuring the practical security of cryptograph. In this paper, we
try to use it into information hiding system (IHS). Because IHS has its
own properties, the ROM must be modified if it is used into IHS.
Firstly, we fully discuss why and how to modify each part of ROM
respectively. The main changes include: 1) Divide the attacks that IHS
may be suffered into two phases and divide the attacks of each phase
into several kinds. 2) Distinguish Oracles and Black-boxes clearly. 3)
Define Oracle and four Black-boxes that IHS used. 4) Propose the
formalized adversary model. And 5) Give the definition of judge.
Secondly, based on ROM of IHS, the security against known original
cover attack (KOCA-KOCA-security) is defined. Then, we give an
actual information hiding scheme and prove that it is
KOCA-KOCA-secure. Finally, we conclude the paper and propose the
open problems of further research.
Abstract: The regional innovative competitiveness is an integrating characteristic of the innovative sphere of the region. It depends on a big variety of different parameters connected with all kinds of economic entities- activities. But management parameters shouldn't be irregular, so in order to avoid it, an institutional system should be formed. This system should carry out strategic management of factors having the greatest influence on the region's innovative development. This article is devoted to different aspects of organization of the region's development institutional mechanism, which is based on management of regional innovative competitiveness parameters. The base of the analysis is innovatively-active Russian regions which were compared according to the level of the innovative competitiveness. After that the most important parameters of successful innovative development of the region were revealed with the help of the correlation-regression analysis. The results of the research could be used for investigation of the region's innovative policy.
Abstract: This paper presents Faults Forecasting System (FFS)
that utilizes statistical forecasting techniques in analyzing process
variables data in order to forecast faults occurrences. FFS is
proposing new idea in detecting faults. Current techniques used in
faults detection are based on analyzing the current status of the
system variables in order to check if the current status is fault or not.
FFS is using forecasting techniques to predict future timing for faults
before it happens. Proposed model is applying subset modeling
strategy and Bayesian approach in order to decrease dimensionality
of the process variables and improve faults forecasting accuracy. A
practical experiment, designed and implemented in Okayama
University, Japan, is implemented, and the comparison shows that
our proposed model is showing high forecasting accuracy and
BEFORE-TIME.
Abstract: The paper presents a part of the results obtained in a
complex research project on Romanian Grey Steppe breed, owner of
some remarkable qualities such as hardiness, longevity, adaptability,
special resistance to ban weather and diseases and included in the
genetic fund (G.D. no. 822/2008.) from Romania.
Following the researches effectuated, we identified alleles of six
loci, codifying the six types of major milk proteins: alpha-casein S1
(α S1-cz); beta-casein (β-cz); kappa-casein (K-cz); beta-lactoglobulin
(β-lg); alpha-lactalbumin (α-la) and alpha-casein S2 (α S2-cz). In
system αS1-cz allele αs1-Cn B has the highest frequency (0.700), in
system β-cz allele β-Cn A2 ( 0.550 ), in system K-cz allele k-CnA2 (
0.583 ) and heterozygote genotype AB ( 0.416 ) and BB (0.375), in
system β-lg allele β-lgA1 has the highest frequency (0.542 ) and
heterozygote genotype AB ( 0.500 ), in system α-la there is
monomorphism for allele α-la B and similarly in system αS2-cz for
allele αs2-Cn A.
The milk analysis by the isoelectric focalization technique (I.E.F.)
allowed the identification of a new allele for locus αS1-casein, for two
of the individuals under analysis, namely allele called αS1-casein
IRV. When experiments were repeated, we noticed that this is not a
proteolysis band and it really was a new allele that has not been
registered in the specialized literature so far. We identified two
heterozygote individuals, carriers of this allele, namely: BIRV and
CIRV. This discovery is extremely important if focus is laid on the
national genetic patrimony.
Abstract: The draw solute separation process in Forward
Osmosis desalination was simulated in Aspen Plus chemical process
modeling software, to estimate the energy consumption and compare
it with other desalination processes, mainly the Reverse Osmosis
process which is currently most prevalent. The electrolytic chemistry
for the system was retrieved using the Elec – NRTL property method
in the Aspen Plus database. Electrical equivalent of energy required
in the Forward Osmosis desalination technique was estimated and
compared with the prevalent desalination techniques.
Abstract: In this paper the vibration behaviors of a structure equipped with a tuned liquid column damper (TLCD) under a harmonic type of earthquake loading are studied. However, due to inherent nonlinear liquid damping, it is no doubt that a great deal of computational effort is required to search the optimum parameters of the TLCD, numerically. Therefore by linearization the equation of motion of the single degree of freedom structure equipped with the TLCD, the closed form solutions of the TLCD-structure system are derived. To find the reliability of the analytical method, the results have been compared with other researcher and have good agreement. Further, the effects of optimal design parameters such as length ratio and mass ratio on the performance of the TLCD for controlling the responses of a structure are investigated by using the harmonic type of earthquake excitation. Finally, the Citicorp Center which has a very flexible structure is used as an example to illustrate the design procedure for the TLCD under the earthquake excitation.
Abstract: This paper deals with the design, development & implementation of a temperature sensor using zigbee. The main aim of the work undertaken in this paper is to sense the temperature and to display the result on the LCD using the zigbee technology. ZigBee operates in the industrial, scientific and medical (ISM) radio bands; 868 MHz in Europe, 915 MHz in the USA and 2.4 GHz in most jurisdictions worldwide. The technology is intended to be simpler and cheaper than other WPANs such as Bluetooth. The most capable ZigBee node type is said to require only about 10 % of the software of a typical Bluetooth or Wireless Internet node, while the simplest nodes are about 2 %. However, actual code sizes are much higher, more like 50 % of the Bluetooth code size. ZigBee chip vendors have announced 128-kilobyte devices. In this work undertaken in the design & development of the temperature sensor, it senses the temperature and after amplification is then fed to the micro controller, this is then connected to the zigbee module, which transmits the data and at the other end the zigbee reads the data and displays on to the LCD. The software developed is highly accurate and works at a very high speed. The method developed shows the effectiveness of the scheme employed.
Abstract: This paper proposes new algorithms for the computeraided
design and manufacture (CAD/CAM) of 3D woven multi-layer
textile structures. Existing commercial CAD/CAM systems are often
restricted to the design and manufacture of 2D weaves. Those
CAD/CAM systems that do support the design and manufacture of
3D multi-layer weaves are often limited to manual editing of design
paper grids on the computer display and weave retrieval from stored
archives. This complex design activity is time-consuming, tedious
and error-prone and requires considerable experience and skill of a
technical weaver. Recent research reported in the literature has
addressed some of the shortcomings of commercial 3D multi-layer
weave CAD/CAM systems. However, earlier research results have
shown the need for further work on weave specification, weave
generation, yarn path editing and layer binding. Analysis of 3D
multi-layer weaves in this research has led to the design and
development of efficient and robust algorithms for the CAD/CAM of
3D woven multi-layer textile structures. The resulting algorithmically
generated weave designs can be used as a basis for lifting plans that
can be loaded onto looms equipped with electronic shedding
mechanisms for the CAM of 3D woven multi-layer textile structures.