Abstract: In pressure vessels contain hydrogen, the role of
hydrogen will be important because of hydrogen cracking problem. It
is difficult to predict what is happened in metallurgical field spite of a
lot of studies have been searched. The main role in controlling the
mass diffusion as driving force is related to stress. In this study, finite
element analysis is implemented to estimate material-s behavior
associated with hydrogen embrittlement. For this purpose, one model
of a pressure vessel is introduced that it has definite boundary and
initial conditions. In fact, finite element is employed to solve the
sequentially coupled mass diffusion with stress near a crack front in a
pressure vessel. Modeling simulation intergrarnular fracture of AISI
4135 steel due to hydrogen is investigated. So, distribution of
hydrogen and stress are obtained and they indicate that their
maximum amounts occur near the crack front. This phenomenon is
happened exactly the region between elastic and plastic field.
Therefore, hydrogen is highly mobile and can diffuse through crystal
lattice so that this zone is potential to trap high volume of hydrogen.
Consequently, crack growth and fast fracture will be happened.
Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: Transient Stability is an important issue in power systems planning, operation and extension. The objective of transient stability analysis problem is not satisfied with mere transient instability detection or evaluation and it is most important to complement it by defining fast and efficient control measures in order to ensure system security. This paper presents a new Fuzzy Support Vector Machines (FSVM) to investigate the stability status of power systems and a modified generation rescheduling scheme to bring back the identified unstable cases to a more economical and stable operating point. FSVM improves the traditional SVM (Support Vector Machines) by adding fuzzy membership to each training sample to indicate the degree of membership of this sample to different classes. The preventive control based on economic generator rescheduling avoids the instability of the power systems with minimum change in operating cost under disturbed conditions. Numerical results on the New England 39 bus test system show the effectiveness of the proposed method.
Abstract: The massive proliferation of affordable computers, Internet broadband connectivity and rich education content has created a global phenomenon in which information and communication technology (ICT) is being used to transform education. Therefore, there is a need to redesign the educational system to meet the needs better. The advent of computers with sophisticated software has made it possible to solve many complex problems very fast and at a lower cost. This paper introduces the characteristics of the current E-Learning and then analyses the concept of cloud computing and describes the architecture of cloud computing platform by combining the features of E-Learning. The authors have tried to introduce cloud computing to e-learning, build an e-learning cloud, and make an active research and exploration for it from the following aspects: architecture, construction method and external interface with the model.
Abstract: IETF RFC 2002 originally introduced the wireless
Mobile-IP protocol to support portable IP addresses for mobile
devices that often change their network access points to the Internet.
The inefficiency of this protocol mainly within the handoff
management produces large end-to-end packet delays, during
registration process, and further degrades the system efficiency due to
packet losses between subnets. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated. The heuristic of configuration file during
practical Setup session for registration parameters, on Cisco platform
Router-1760 using IOS 12.3 (15)T is created. Finally, stand-alone
performance simulations results from Simulink Matlab, within each
subnet and also between subnets, are illustrated for reporting better
end-to-end packet delays. Results verified the effectiveness of our
Mathcad analytical manipulation and experimental implementation. It
showed lower values of end-to-end packet delay for Mobile-IP using
CIA procedure. Furthermore, it reported packets flow between
subnets to improve packet losses between subnets.
Abstract: Computer networks are essential part in computerbased
information systems. The performance of these networks has a
great influence on the whole information system. Measuring the
usability criteria and customers satisfaction on small computer
network is very important. In this article, an effective approach for
measuring the usability of business network in an information system
is introduced. The usability process for networking provides us with a
flexible and a cost-effective way to assess the usability of a network
and its products. In addition, the proposed approach can be used to
certify network product usability late in the development cycle.
Furthermore, it can be used to help in developing usable interfaces
very early in the cycle and to give a way to measure, track, and
improve usability. Moreover, a new approach for fast information
processing over computer networks is presented. The entire data are
collected together in a long vector and then tested as a one input
pattern. Proposed fast time delay neural networks (FTDNNs) use
cross correlation in the frequency domain between the tested data and
the input weights of neural networks. It is proved mathematically and
practically that the number of computation steps required for the
presented time delay neural networks is less than that needed by
conventional time delay neural networks (CTDNNs). Simulation
results using MATLAB confirm the theoretical computations.
Abstract: A new genetic algorithm, termed the 'optimum individual monogenetic genetic algorithm' (OIMGA), is presented whose properties have been deliberately designed to be well suited to hardware implementation. Specific design criteria were to ensure fast access to the individuals in the population, to keep the required silicon area for hardware implementation to a minimum and to incorporate flexibility in the structure for the targeting of a range of applications. The first two criteria are met by retaining only the current optimum individual, thereby guaranteeing a small memory requirement that can easily be stored in fast on-chip memory. Also, OIMGA can be easily reconfigured to allow the investigation of problems that normally warrant either large GA populations or individuals many genes in length. Local convergence is achieved in OIMGA by retaining elite individuals, while population diversity is ensured by continually searching for the best individuals in fresh regions of the search space. The results given in this paper demonstrate that both the performance of OIMGA and its convergence time are superior to those of a range of existing hardware GA implementations.
Abstract: Spent petroleum catalyst from Korean petrochemical
industry contains trace amount of metals such as Ni, V and Mo.
Therefore an attempt was made to recover those trace metal using
bioleaching process. Different leaching parameters such as Fe(II)
concentration, pulp density, pH, temperature and particle size of
spent catalyst particle were studied to evaluate their effects on the
leaching efficiency. All the three metal ions like Ni, V and Mo
followed dual kinetics, i.e., initial faster followed by slower rate. The
percentage of leaching efficiency of Ni and V were higher than Mo.
The leaching process followed a diffusion controlled model and the
product layer was observed to be impervious due to formation of
ammonium jarosite (NH4)Fe3(SO4)2(OH)6. In addition, the lower
leaching efficiency of Mo was observed due to a hydrophobic coating
of elemental sulfur over Mo matrix in the spent catalyst.
Abstract: In this study we survey the method for fast finding a minimum link path between two arbitrary points within a simple polygon, which can pass only through the vertices, with preprocessing.
Abstract: A multivariable discontinuous feedback linearization approach is proposed to position control of an electrically driven fast robot manipulator. A desired performance is achieved by selecting a useful controller and suitable sampling rate and considering saturation for actuators. There is a high flexibility to apply the proposed control approach on different electrically driven manipulators. The control approach can guarantee the stability and satisfactory tracking performance. A PUMA 560 robot driven by geared permanent magnet dc motors is simulated. The simulation results show a desired performance for control system under technical specifications.
Abstract: Cerium-doped lanthanum bromide LaBr3:Ce(5%)
crystals are considered to be one of the most advanced scintillator
materials used in PET scanning, combining a high light yield, fast
decay time and excellent energy resolution. Apart from the correct
choice of scintillator, it is also important to optimise the detector
geometry, not least in terms of source-to-detector distance in order to
obtain reliable measurements and efficiency. In this study a
commercially available 25 mm x 25 mm BrilLanCeTM 380 LaBr3: Ce
(5%) detector was characterised in terms of its efficiency at varying
source-to-detector distances. Gamma-ray spectra of 22Na, 60Co, and
137Cs were separately acquired at distances of 5, 10, 15, and 20cm. As
a result of the change in solid angle subtended by the detector, the
geometric efficiency reduced in efficiency with increasing distance.
High efficiencies at low distances can cause pulse pile-up when
subsequent photons are detected before previously detected events
have decayed. To reduce this systematic error the source-to-detector
distance should be balanced between efficiency and pulse pile-up
suppression as otherwise pile-up corrections would need to be
necessary at short distances. In addition to the experimental
measurements Monte Carlo simulations have been carried out for the
same setup, allowing a comparison of results. The advantages and
disadvantages of each approach have been highlighted.
Abstract: In a wireless communication system, a
predistorter(PD) is often employed to alleviate nonlinear distortions
due to operating a power amplifier near saturation, thereby improving
the system performance and reducing the interference to adjacent
channels. This paper presents a new adaptive polynomial digital
predistorter(DPD). The proposed DPD uses Coordinate Rotation
Digital Computing(CORDIC) processors and PD process by pipelined
architecture. It is simpler and faster than conventional adaptive
polynomial DPD. The performance of the proposed DPD is proved by
MATLAB simulation.
Abstract: With the rapid development in the field of life
sciences and the flooding of genomic information, the need for faster
and scalable searching methods has become urgent. One of the
approaches that were investigated is indexing. The indexing methods
have been categorized into three categories which are the lengthbased
index algorithms, transformation-based algorithms and mixed
techniques-based algorithms. In this research, we focused on the
transformation based methods. We embedded the N-gram method
into the transformation-based method to build an inverted index
table. We then applied the parallel methods to speed up the index
building time and to reduce the overall retrieval time when querying
the genomic database. Our experiments show that the use of N-Gram
transformation algorithm is an economical solution; it saves time and
space too. The result shows that the size of the index is smaller than
the size of the dataset when the size of N-Gram is 5 and 6. The
parallel N-Gram transformation algorithm-s results indicate that the
uses of parallel programming with large dataset are promising which
can be improved further.
Abstract: Topics Disaster and Emergency Management are highly debated among experts. Fast communication will help to deal with emergencies. Problem is with the network connection and data exchange. The paper suggests a solution, which allows possibilities and perspectives of new flexible communication platform to the protection of communication systems for crisis management. This platform is used for everyday communication and communication in crisis situations too.
Abstract: With the advent of emerging personal computing paradigms such as ubiquitous and mobile computing, Web contents are becoming accessible from a wide range of mobile devices. Since these devices do not have the same rendering capabilities, Web contents need to be adapted for transparent access from a variety of client agents. Such content adaptation is exploited for either an individual element or a set of consecutive elements in a Web document and results in better rendering and faster delivery to the client device. Nevertheless, Web content adaptation sets new challenges for semantic markup. This paper presents an advanced components platform, called SMC, enabling the development of mobility applications and services according to a channel model based on the principles of Services Oriented Architecture (SOA). It then goes on to describe the potential for integration with the Semantic Web through a novel framework of external semantic annotation that prescribes a scheme for representing semantic markup files and a way of associating Web documents with these external annotations. The role of semantic annotation in this framework is to describe the contents of individual documents themselves, assuring the preservation of the semantics during the process of adapting content rendering. Semantic Web content adaptation is a way of adding value to Web contents and facilitates repurposing of Web contents (enhanced browsing, Web Services location and access, etc).
Abstract: In order to make surfing the internet faster, and to save redundant processing load with each request for the same web page, many caching techniques have been developed to reduce latency of retrieving data on World Wide Web. In this paper we will give a quick overview of existing web caching techniques used for dynamic web pages then we will introduce a design and implementation model that take advantage of “URL Rewriting" feature in some popular web servers, e.g. Apache, to provide an effective approach of caching dynamic web pages.
Abstract: Ramadan requires individuals to abstain from food and fluid intake between sunrise and sunset; physiological considerations predict that poorer mood, physical performance and mental performance will result. In addition, any difficulties will be worsened because preparations for fasting and recovery from it often mean that nocturnal sleep is decreased in length, and this independently affects mood and performance.
A difficulty of interpretation in many studies is that the observed changes could be due to fasting but also to the decreased length of sleep and altered food and fluid intakes before and after the daytime fasting. These factors were separated in this study, which took place over three separate days and compared the effects of different durations of fasting (4, 8 or 16h) upon a wide variety of measures (including subjective and objective assessments of performance, body composition, dehydration and responses to a short bout of exercise) - but with an unchanged amount of nocturnal sleep, controlled supper the previous evening, controlled intakes at breakfast and daytime naps not being allowed. Many of the negative effects of fasting observed in previous studies were present in this experiment also. These findings indicate that fasting was responsible for many of the changes previously observed, though some effect of sleep loss, particularly if occurring on successive days (as would occur in Ramadan) cannot be excluded.
Abstract: Documents clustering become an essential technology
with the popularity of the Internet. That also means that fast and
high-quality document clustering technique play core topics. Text
clustering or shortly clustering is about discovering semantically
related groups in an unstructured collection of documents. Clustering
has been very popular for a long time because it provides unique
ways of digesting and generalizing large amounts of information.
One of the issues of clustering is to extract proper feature (concept)
of a problem domain. The existing clustering technology mainly
focuses on term weight calculation. To achieve more accurate
document clustering, more informative features including concept
weight are important. Feature Selection is important for clustering
process because some of the irrelevant or redundant feature may
misguide the clustering results. To counteract this issue, the proposed
system presents the concept weight for text clustering system
developed based on a k-means algorithm in accordance with the
principles of ontology so that the important of words of a cluster can
be identified by the weight values. To a certain extent, it has resolved
the semantic problem in specific areas.
Abstract: The size, complexity and number of databases used
for protein information have caused bioinformatics to lag behind in
adapting to the need to handle this distributed information.
Integrating all the information from different databases into one
database is a challenging problem. Our main research is to develop a
tool which can be used to access and manipulate protein information
from difference databases. In our approach, we have integrated
difference databases such as Swiss-prot, PDB, Interpro, and EMBL
and transformed these databases in flat file format into relational
form using XML and Bioperl. As a result, we showed this tool can
search different sizes of protein information stored in relational
database and the result can be retrieved faster compared to flat file
database. A web based user interface is provided to allow user to
access or search for protein information in the local database.
Abstract: This paper features the modeling and design of a Fast
Output Sampling (FOS) Feedback control technique for the Active
Vibration Control (AVC) of a smart flexible aluminium cantilever
beam for a Single Input Single Output (SISO) case. Controllers are
designed for the beam by bonding patches of piezoelectric layer as
sensor / actuator to the master structure at different locations along
the length of the beam by retaining the first 2 dominant vibratory
modes. The entire structure is modeled in state space form using the
concept of piezoelectric theory, Euler-Bernoulli beam theory, Finite
Element Method (FEM) and the state space techniques by dividing
the structure into 3, 4, 5 finite elements, thus giving rise to three
types of systems, viz., system 1 (beam divided into 3 finite
elements), system 2 (4 finite elements), system 3 (5 finite elements).
The effect of placing the sensor / actuator at various locations along
the length of the beam for all the 3 types of systems considered is
observed and the conclusions are drawn for the best performance and
for the smallest magnitude of the control input required to control the
vibrations of the beam. Simulations are performed in MATLAB. The
open loop responses, closed loop responses and the tip displacements
with and without the controller are obtained and the performance of
the proposed smart system is evaluated for vibration control.