Abstract: Three batches of yogurts were made with soy protein
isolate (SPI) supplemented with 2% (S2), 4% (S4) or 6% (S6) of
skim milk powder (SMP). The fourth batch (control; S0) was
prepared from SPI without SMP supplementation. Lactobacillus
delbrueckii ssp. bulgaricus ATCC 11842 (Lb 11842) and
Streptococcus thermophilus ST 1342 (ST 1342) were used as the
starter culture. Biotransformation of the inactive forms, isoflavone
glycosides (IG) to biologically active forms, isoflavone aglycones
(IA), was determined during 28 d storage. The viability of both
microorganisms was significantly higher (P < 0.05) in S2, S4, and S6
than that in S0. The ratio of lactic acid/acetic acid in S0 was in the
range of 15.53 – 22.31 compared to 7.24 – 12.81 in S2, S4 and S6.
The biotransformation of IG to IA in S2, S4 and S6 was also
enhanced by 9.9 -13.3% compared to S0.
Abstract: A handful of propagation textbooks that discuss radio frequency (RF) propagation models merely list out the models and perhaps discuss them rather briefly; this may well be frustrating for the potential first time modeller who's got no idea on how these models could have been derived. This paper fundamentally provides an overture in modelling the radio channel. Explicitly, for the modelling practice discussed here, signal strength field measurements had to be conducted beforehand (this was done at 469 MHz); to be precise, this paper primarily concerns empirically/statistically modelling the radio channel, and thus provides results obtained from empirically modelling the environments in question. This paper, on the whole, proposes three propagation models, corresponding to three experimented environments. Perceptibly, the models have been derived by way of making the most use of statistical measures. Generally speaking, the first two models were derived via simple linear regression analysis, whereas the third have been originated using multiple regression analysis (with five various predictors). Additionally, as implied by the title of this paper, both indoor and outdoor environments have been experimented; however, (somewhat) two of the environments are neither entirely indoor nor entirely outdoor. The other environment, however, is completely indoor.
Abstract: Thailand is one of the world-s leaders of rice
producers and exporters. Farmers have to increase the rice cultivation
frequency for serving the national increasing of export-s demand. It
leads to an elimination of rice residues by open burning which is the
quickest and costless management method. The open burning of rice
residue is one of the major causes of air pollutants and greenhouse
gas (GHG) emission. Under ASEAN agreement on trans-boundary
haze, Thailand set the master plan to mitigate air pollutant emission
from open burning of agricultural residues. In this master plan,
residues incorporation is promoted as alternative management
method to open burning. However, the assessment of both options in
term of GHG emission in order to investigate their contribution to
long-term global warming is still scarce or inexistent. In this study, a
method on rice residues assessment was first developed in order to
estimate and compare GHG emissions from rice cultivation under
rice residues open burning and the case with incorporation of the
same amount of rice residues, using 2006 IPCC guidelines for
emission estimation and Life Cycle Analysis technique. The
emission from rice cultivation in different preparing area practice
was also discussed.
Abstract: In this paper, perceptions of actors on changes in
crop productivity, quantity and quality of water, and determinants of
their perception are analyzed using descriptive statistics and ordered
logit model. Data collected from 297 Ethiopian farmers and 103
agricultural professionals from December 2009 to January 2010 are
employed. Results show that the majority of the farmers and
professionals recognized decline in water resources, reasoning
climate changes and soil erosion as some of the causes. However,
there is a variation in views on changes in productivity. The
household asset, education level, age and geographical positions are
found to affect farmers- perception on changes in crop productivity.
But, the study underlines that there is no evidence that farmers-
economic status, age, or education level affects recognition of
degradation of water resources. Thus, more focus shall be given on
providing them different coping mechanisms and alternative
resource conserving technologies than educating about the
problems.
Abstract: Supply chain consists of all stages involved, directly
or indirectly, includes all functions involved in fulfilling a customer
demand. In two stage transportation supply chain problem,
transportation costs are of a significant proportion of final product
costs. It is often crucial for successful decisions making approaches
in two stage supply chain to explicit account for non-linear
transportation costs. In this paper, deterministic demand and finite
supply of products was considered. The optimized distribution level
and the routing structure from the manufacturing plants to the
distribution centres and to the end customers is determined using
developed mathematical model and solved by proposed particle
swarm optimization based genetic algorithm. Numerical analysis of
the case study is carried out to validate the model.
Abstract: The current situation in the eurozone raises a number of topics for discussion and to help in finding an answer to the question of whether a common currency is a more suitable means of coping with the impact of the financial crisis or whether national currencies are better suited to this. The economic situation in the EU is now considerably volatile and, due to problems with the fulfilment of the Maastricht convergence criteria, it is now being considered whether, in their further development, new member states will decide to distance themselves from the euro or will, in an attempt to overcome the crisis, speed up the adoption of the euro. The Czech Republic is one country with little interest in adopting the euro, justified by the fact that a better alternative to dealing with this crisis is an independent monetary policy and its ability to respond flexibly to the economic situation not only in Europe, but around the world. One attribute of the crisis in the Czech Republic and its mitigation is the freely floating exchange rate of the national currency. It is not only the Czech Republic that is attempting to alleviate the impact of the crisis, but also new EU member countries facing fresh questions to which theory have yet to provide wholly satisfactory answers. These questions undoubtedly include the problem of inflation targeting and the choice of appropriate instruments for achieving financial stability. The difficulty lies in the fact that these objectives may be contradictory and may require more than one means of achieving them. In this respect we may assume that membership of the euro zone might not in itself mitigate the development of the recession or protect the nation from future crises. We are of the opinion that the decisive factor in the development of any economy will continue to be the domestic economic policy and the operability of market economic mechanisms. We attempt to document this fact using selected countries as examples, these being the Czech Republic, Poland, Hungary, and Slovakia.
Abstract: In the modern manufacturing systems, the use of
thermal cutting techniques using oxyfuel, plasma and laser have
become indispensable for the shape forming of high quality complex
components; however, the conventional chip removal production
techniques still have its widespread space in the manufacturing
industry. Both these types of machining operations require the
positioning of end effector tool at the edge where the cutting process
commences. This repositioning of the cutting tool in every machining
operation is repeated several times and is termed as non-productive
time or airtime motion. Minimization of this non-productive
machining time plays an important role in mass production with high
speed machining. As, the tool moves from one region to the other by
rapid movement and visits a meticulous region once in the whole
operation, hence the non-productive time can be minimized by
synchronizing the tool movements. In this work, this problem is
being formulated as a general travelling salesman problem (TSP) and
a genetic algorithm approach has been applied to solve the same. For
improving the efficiency of the algorithm, the GA has been
hybridized with a noble special heuristic and simulating annealing
(SA). In the present work a novel heuristic in the combination of GA
has been developed for synchronization of toolpath movements
during repositioning of the tool. A comparative analysis of new Meta
heuristic techniques with simple genetic algorithm has been
performed. The proposed metaheuristic approach shows better
performance than simple genetic algorithm for minimization of nonproductive
toolpath length. Also, the results obtained with the help of
hybrid simulated annealing genetic algorithm (HSAGA) are also
found better than the results using simple genetic algorithm only.
Abstract: In this paper we present an extension to Vision Based
LRTA* (VLRTA*) known as Vision Based Moving Target Search
(VMTS) for capturing unknown moving target in unknown territory
with randomly generated obstacles. Target position is unknown to the
agents and they cannot predict its position using any probability
method. Agents have omni directional vision but can see in one
direction at some point in time. Agent-s vision will be blocked by the
obstacles in the search space so agent can not see through the
obstacles. Proposed algorithm is evaluated on large number of
scenarios. Scenarios include grids of sizes from 10x10 to 100x100.
Grids had obstacles randomly placed, occupying 0% to 50%, in
increments of 10%, of the search space. Experiments used 2 to 9
agents for each randomly generated maze with same obstacle ratio.
Observed results suggests that VMTS is effective in locate target
time, solution quality and virtual target. In addition, VMTS becomes
more efficient if the number of agents is increased with proportion to
obstacle ratio.
Abstract: The rheological properties of light crude oil and its mixture with water were investigated experimentally. These rheological properties include steady flow behavior, yield stress, transient flow behavior, and viscoelastic behavior. A RheoStress RS600 rheometer was employed in all of the rheological examination tests. The light crude oil exhibits a Newtonian and for emulsion exhibits a non-Newtonian shear thinning behavior over the examined shear rate range of 0.1–120 s-1. In first time, a series of samples of crude oil from the Algerian Sahara has been tested and the results expressed in terms of τ=f(γ) have demonstrated their Newtonian character for the temperature included in [20°C, 70°C]. In second time and at T=20°C, the oil-water emulsions (30%, 50% and 70%) by volume of water), thermodynamically stable, have demonstrated a non-Newtonian rheological behavior that is to say, Herschel-Bulkley and Bingham types. For each type of crude oil-water emulsion, the rheological parameters are calculated by numerical treatment of results.
Abstract: This paper addresses the problem of peak-to-average
power ratio (PAPR) in orthogonal frequency division multiplexing
(OFDM) systems. It also introduces a new PAPR reduction technique
based on adaptive square-rooting (SQRT) companding process. The
SQRT process of the proposed technique changes the statistical
characteristics of the OFDM output signals from Rayleigh
distribution to Gaussian-like distribution. This change in statistical
distribution results changes of both the peak and average power
values of OFDM signals, and consequently reduces significantly the
PAPR. For the 64QAM OFDM system using 512 subcarriers, up to 6
dB reduction in PAPR was achieved by square-rooting technique
with fixed degradation in bit error rate (BER) equal to 3 dB.
However, the PAPR is reduced at the expense of only -15 dB out-ofband
spectral shoulder re-growth below the in-band signal level. The
proposed adaptive SQRT technique is superior in terms of BER
performance than the original, non-adaptive, square-rooting
technique when the required reduction in PAPR is no more than 5
dB. Also, it provides fixed amount of PAPR reduction in which it is
not available in the original SQRT technique.
Abstract: Two-dimensional finite element model was created in this work to investigate the stresses distribution within rock-like samples with offset open non-persistent joints under biaxial loading. The results of this study have explained the fracture mechanisms observed in tests on rock-like material with open non-persistent offset joints [1]. Finite element code SAP2000 was used to study the stresses distribution within the specimens. Four-nodded isoperimetric plain strain element with two degree of freedom per node, and the three-nodded constant strain triangular element with two degree of freedom per node were used in the present study.The results of the present study explained the formation of wing cracks at the tip of the joints for low confining stress as well as the formation of wing cracks at the middle of the joint for the higher confining stress. High shear stresses found in the numerical study at the tip of the joints explained the formation of secondary cracks at the tip of the joints in the experimental study. The study results coincide with the experimental observations which showed that for bridge inclination of 0o, the coalescence occurred due to shear failure and for bridge inclination of 90o the coalescence occurred due to tensile failure while for the other bridge inclinations coalescence occurred due to mixed tensile and shear failure.
Abstract: Many organisations are nowadays interested to adopt
lean manufacturing strategy that would enable them to compete in
this competitive globalisation market. In this respect, it is necessary
to assess the implementation of lean manufacturing in different
organisations so that the important best practices can be identified.
This paper describes the development of key areas which will be
used to assess the adoption and implementation of lean
manufacturing practices. There are some key areas developed to
evaluate and reduce the most optimal projects so as to enhance their
production efficiency and increase the purpose of the economic
benefits of the manufacturing unit.
Lean manufacturing is becoming lean enterprise by treating its
customers and suppliers as partners. This gives the extra edge in
today-s cost and time competitive markets. The organisation is
becoming strong in all the conventional competition points. They are
Price, Quality and Delivery. Lean enterprise owners can deliver high
quality products quickly, with low price.
Abstract: In the present study, the effects of ultrasound as
emerging technology were investigated on germination stimulation,
amount of alpha-amylase activity on dry barley seeds before steeping
stage of malting process. All experiments were carried out at 20 KHz
on the ultrasonic generator in 3 different ultrasonic intensities (20, 60
and 100% setting from total power of device) and time (5, 10 and 15
min) at constant temperature (30C). For determining the effects of
these parameters on enzyme the Fuwa method assay based on the
decreased staining value of blue starch–iodine complexes employed
for measurement an activity. The results of these assays were
analyzed by Qualitek4 software using the Taguchi statistical method
to evaluate the factor-s effects on enzyme activity. It has been found
that when malting barley is irradiated with an ultrasonic power, a
stimulating effect occurs as to the enzyme activity.
Abstract: The choice of finite element to use in order to predict
nonlinear static or dynamic response of complex structures becomes
an important factor. Then, the main goal of this research work is to
focus a study on the effect of the in-plane rotational degrees of
freedom in linear and geometrically non linear static and dynamic
analysis of thin shell structures by flat shell finite elements. In this
purpose: First, simple triangular and quadrilateral flat shell finite
elements are implemented in an incremental formulation based on the
updated lagrangian corotational description for geometrically
nonlinear analysis. The triangular element is a combination of DKT
and CST elements, while the quadrilateral is a combination of DKQ
and the bilinear quadrilateral membrane element. In both elements,
the sixth degree of freedom is handled via introducing fictitious
stiffness. Secondly, in the same code, the sixth degrees of freedom in
these elements is handled differently where the in-plane rotational
d.o.f is considered as an effective d.o.f in the in-plane filed
interpolation. Our goal is to compare resulting shell elements. Third,
the analysis is enlarged to dynamic linear analysis by direct
integration using Newmark-s implicit method. Finally, the linear
dynamic analysis is extended to geometrically nonlinear dynamic
analysis where Newmark-s method is used to integrate equations of
motion and the Newton-Raphson method is employed for iterating
within each time step increment until equilibrium is achieved. The
obtained results demonstrate the effectiveness and robustness of the
interpolation of the in-plane rotational d.o.f. and present deficiencies
of using fictitious stiffness in dynamic linear and nonlinear analysis.
Abstract: In this paper, the typical exponential method, diamond difference and modified time discrete scheme is researched for self adaptive time step. The second-order time evolution scheme is applied to time-dependent spherical neutron transport equation by discrete ordinates method. The numerical results show that second-order time evolution scheme associated exponential method has some good properties. The time differential curve about neutron current is more smooth than that of exponential method and diamond difference and modified time discrete scheme.
Abstract: The aim of this paper is to study the oblique
stagnation point flow on vertical plate with uniform surface heat flux
in presence of magnetic field. Using Stream function, partial
differential equations corresponding to the momentum and energy
equations are converted into non-linear ordinary differential
equations. Numerical solutions of these equations are obtained using
Runge-Kutta Fehlberg method with the help of shooting technique.
In the present work the effects of striking angle, magnetic field
parameter, Grashoff number, the Prandtl number on velocity and heat
transfer characteristics have been discussed. Effect of above
mentioned parameter on the position of stagnation point are also
studied.
Abstract: In this paper, a Smart Home Service Robot, McBot II,
which performs mess-cleanup function etc. in house, is designed much
more optimally than other service robots. It is newly developed in
much more practical system than McBot I which we had developed
two years ago. One characteristic attribute of mobile platforms
equipped with a set of dependent wheels is their omni- directionality
and the ability to realize complex translational and rotational
trajectories for agile navigation in door. An accurate coordination of
steering angle and spinning rate of each wheel is necessary for a
consistent motion. This paper develops trajectory controller of
3-wheels omni-directional mobile robot using fuzzy azimuth estimator.
A specialized anthropomorphic robot manipulator which can be
attached to the housemaid robot McBot II, is developed in this paper.
This built-in type manipulator consists of both arms with 3 DOF
(Degree of Freedom) each and both hands with 3 DOF each. The
robotic arm is optimally designed to satisfy both the minimum
mechanical size and the maximum workspace. Minimum mass and
length are required for the built-in cooperated-arms system. But that
makes the workspace so small. This paper proposes optimal design
method to overcome the problem by using neck joint to move the arms
horizontally forward/backward and waist joint to move them
vertically up/down. The robotic hand, which has two fingers and a
thumb, is also optimally designed in task-based concept. Finally, the
good performance of the developed McBot II is confirmed through
live tests of the mess-cleanup task.
Abstract: IETF RFC 2002 originally introduced the wireless
Mobile-IP protocol to support portable IP addresses for mobile
devices that often change their network access points to the Internet.
The inefficiency of this protocol mainly within the handoff
management produces large end-to-end packet delays, during
registration process, and further degrades the system efficiency due to
packet losses between subnets. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated. The heuristic of configuration file during
practical Setup session for registration parameters, on Cisco platform
Router-1760 using IOS 12.3 (15)T is created. Finally, stand-alone
performance simulations results from Simulink Matlab, within each
subnet and also between subnets, are illustrated for reporting better
end-to-end packet delays. Results verified the effectiveness of our
Mathcad analytical manipulation and experimental implementation. It
showed lower values of end-to-end packet delay for Mobile-IP using
CIA procedure. Furthermore, it reported packets flow between
subnets to improve packet losses between subnets.
Abstract: In this paper we used data mining techniques to
identify outlier patients who are using large amount of drugs over a
long period of time. Any healthcare or health insurance system
should deal with the quantities of drugs utilized by chronic diseases
patients. In Kingdom of Bahrain, about 20% of health budget is spent
on medications. For the managers of healthcare systems, there is no
enough information about the ways of drug utilization by chronic
diseases patients, is there any misuse or is there outliers patients. In
this work, which has been done in cooperation with information
department in the Bahrain Defence Force hospital; we select the data
for Cardiac patients in the period starting from 1/1/2008 to
December 31/12/2008 to be the data for the model in this paper. We
used three techniques for finding the drug utilization for cardiac
patients. First we applied a clustering technique, followed by
measuring of clustering validity, and finally we applied a decision
tree as classification algorithm. The clustering results is divided into
three clusters according to the drug utilization, for 1603 patients, who
received 15,806 prescriptions during this period can be partitioned
into three groups, where 23 patients (2.59%) who received 1316
prescriptions (8.32%) are classified to be outliers. The classification
algorithm shows that the use of average drug utilization and the age,
and the gender of the patient can be considered to be the main
predictive factors in the induced model.
Abstract: The incidence of oral cancer in Taiwan increased year
by year. It replaced the nasopharyngeal as the top incurrence among
head and neck cancers since 1994. Early examination and earlier
identification for earlier treatment is the most effective medical
treatment for these cancers. Although the government fully subsidized
the expenses with tremendous promotion program for oral cancer
screening, the citizen-s participation remained low. Purpose of this
study is to understand the factors affecting the citizens- behavior
intensions of taking an oral cancer screening. Based on the Theory of
Planned Behavior, this study adopted four distinctive variables in
explaining the captioned behavior intentions.700 questionnaires were
dispatched with 500 valid responses or 71.4% returned by the citizens
with an age 30 or above from the eastern counties of Taiwan. Test
results has shown that attitude toward, subjective norms of, and
perceived behavioral control over the oral cancer screening varied
from some demographic factors to another. The study proofed that
attitude toward, subjective norms of, and perceived behavioral control
over the oral cancer screening had positive impacts on the
corresponding behavior intention. The test concluded that the theory
of planned behavior was appropriate as a theoretical framework in
explaining the influencing factors of intentions of taking oral cancer
screening. This study suggested the healthcare professional should
provide high accessibility of screening services other than just
delivering knowledge on oral cancer to promote the citizens-
intentions of taking the captioned screening. This research also
provided a practical implication to the healthcare professionals when
formulating and implementing promotion instruments for lifting the
screening rate of oral cancer.