Abstract: The problem of complex use of water resources in
Central Asia by taking into consideration the sovereignty of the states
and increasing demand on use of water for economic aspects are
considered. Complex program with appropriate mathematical
software intended for calculation of possible variants of using the
Amudarya up-stream water resources according to satisfaction of
incompatible requirements of the national economics in irrigation
and energy generation is proposed.
Abstract: A numerical study is presented on convective heat transfer in enclosures. The results are addressed to automotive headlights containing new-age light sources like Light Emitting Diodes (LED). The heat transfer from the heat source (LED) to the enclosure walls is investigated for mixed convection as interaction of the forced convection flow from an inlet and an outlet port and the natural convection at the heat source. Unlike existing studies, inlet and outlet port are thermally coupled and do not serve to remove hot fluid. The input power of the heat source is expressed by the Rayleigh number. The internal position of the heat source, the aspect ratio of the enclosure, and the inclination angle of one wall are varied. The results are given in terms of the global Nusselt number and the enclosure Nusselt number that characterize the heat transfer from the source and from the interior fluid to the enclosure walls, respectively. It is found that the heat transfer from the source to the fluid can be maximized if the source is placed in the main stream from the inlet to the outlet port. In this case, the Reynolds number and heat source position have the major impact on the heat transfer. A disadvantageous position has been found where natural and forced convection compete each other. The overall heat transfer from the source to the wall increases with increasing Reynolds number as well as with increasing aspect ratio and decreasing inclination angle. The heat transfer from the interior fluid to the enclosure wall increases upon decreasing the aspect ratio and increasing the inclination angle. This counteracting behaviour is caused by the variation of the area of the enclosure wall. All mixed convection results are compared to the natural convection limit.
Abstract: Iron ore and coal are the two major important raw
materials being used in Iron making industries. Usually ore fines
containing around 5% Alumina are rejected due to higher proportion
of alumina. Therefore, a technology or process which may reduce
the alumina content by 2% by beneficiation process will be highly
attractive . In addition fine coals with ash content is used nearly 12%
is directly injected in blast furnace. Fast fluidization is a technology
by using dry beneficiation of coal and iron ore can be done. During
the fluidization process the iron ore band coal is fluidized at high
velocity in the riser of a fast fluidized bed, the heavier and coarse
particles is generally settled at the bottom in a dense zone of the riser
while the finer and lighter particle are entrained to the top dilute zone
and then via a cyclone is fed back to the bottom of the riser column.
Most of the alumina and low ash fine size coals being lighter are
expected to move up to the riser and by a natural beneficiation of
ores is expected to take place in the riser. Therefore in this study an
attempt has been made for dry beneficiation of iron ore and coal in a
fluidized bed and its hydrodynamic characterization.
Abstract: In two studies we tested the hypothesis that the
appropriate linguistic formulation of a deontic rule – i.e. the
formulation which clarifies the monadic nature of deontic operators
- should produce more correct responses than the conditional
formulation in Wason selection task. We tested this assumption by
presenting a prescription rule and a prohibition rule in conditional
vs. proper deontic formulation. We contrasted this hypothesis with
two other hypotheses derived from social contract theory and
relevance theory. According to the first theory, a deontic rule
expressed in terms of cost-benefit should elicit a cheater detection
module, sensible to mental states attributions and thus able to
discriminate intentional rule violations from accidental rule
violations. We tested this prevision by distinguishing the two types
of violations. According to relevance theory, performance in
selection task should improve by increasing cognitive effect and
decreasing cognitive effort. We tested this prevision by focusing
experimental instructions on the rule vs. the action covered by the
rule. In study 1, in which 480 undergraduates participated, we
tested these predictions through a 2 x 2 x 2 x 2 (type of the rule x
rule formulation x type of violation x experimental instructions)
between-subjects design. In study 2 – carried out by means of a 2 x
2 (rule formulation x type of violation) between-subjects design -
we retested the hypothesis of rule formulation vs. the cheaterdetection
hypothesis through a new version of selection task in
which intentional vs. accidental rule violations were better
discriminated. 240 undergraduates participated in this study.
Results corroborate our hypothesis and challenge the contrasting
assumptions. However, they show that the conditional formulation
of deontic rules produces a lower performance than what is
reported in literature.
Abstract: In this paper, we introduce a new method for elliptical
object identification. The proposed method adopts a hybrid scheme
which consists of Eigen values of covariance matrices, Circular
Hough transform and Bresenham-s raster scan algorithms. In this
approach we use the fact that the large Eigen values and small Eigen
values of covariance matrices are associated with the major and minor
axial lengths of the ellipse. The centre location of the ellipse can be
identified using circular Hough transform (CHT). Sparse matrix
technique is used to perform CHT. Since sparse matrices squeeze zero
elements and contain a small number of nonzero elements they
provide an advantage of matrix storage space and computational time.
Neighborhood suppression scheme is used to find the valid Hough
peaks. The accurate position of circumference pixels is identified
using raster scan algorithm which uses the geometrical symmetry
property. This method does not require the evaluation of tangents or
curvature of edge contours, which are generally very sensitive to
noise working conditions. The proposed method has the advantages of
small storage, high speed and accuracy in identifying the feature. The
new method has been tested on both synthetic and real images.
Several experiments have been conducted on various images with
considerable background noise to reveal the efficacy and robustness.
Experimental results about the accuracy of the proposed method,
comparisons with Hough transform and its variants and other
tangential based methods are reported.
Abstract: A conjugate heat transfer for steady two-dimensional
mixed convection with magnetic hydrodynamic (MHD) flow of an
incompressible quiescent fluid over an unsteady thermal forming
stretching sheet has been studied. A parameter, M, which is used to
represent the dominance of the magnetic effect has been presented in
governing equations. The similar transformation and an implicit
finite-difference method have been used to analyze the present
problem. The numerical solutions of the flow velocity distributions,
temperature profiles, the wall unknown values of f''(0) and '(θ (0) for
calculating the heat transfer of the similar boundary-layer flow are
carried out as functions of the unsteadiness parameter (S), the Prandtl
number (Pr), the space-dependent parameter (A) and
temperature-dependent parameter (B) for heat source/sink and the
magnetic parameter (M). The effects of these parameters have also
discussed. At the results, it will produce greater heat transfer effect
with a larger Pr and M, S, A, B will reduce heat transfer effects. At
last, conjugate heat transfer for the free convection with a larger G has
a good heat transfer effect better than a smaller G=0.
Abstract: In recent years the large scale use of the power electronic equipment has led to an increase of harmonics in the power system. The harmonics results into a poor power quality and have great adverse economical impact on the utilities and customers. Current harmonics are one of the most common power quality problems and are usually resolved by using shunt active filter (SHAF). The main objective of this work is to develop PI and Fuzzy logic controllers (FLC) to analyze the performance of Shunt Active Filter for mitigating current harmonics under balanced and unbalanced sinusoidal source voltage conditions for normal load and increased load. When the supply voltages are ideal (balanced), both PI and FLC are converging to the same compensation characteristics. However, the supply voltages are non-ideal (unbalanced), FLC offers outstanding results. Simulation results validate the superiority of FLC with triangular membership function over the PI controller.
Abstract: Experiments with pumpkin-rowanberry marmalade
candies were carried out at the Faculty of Food Technology of the
Latvia University of Agriculture. The objective of this investigation
was to evaluate the quality changes of pumpkin-rowanberry
marmalade candies packed in different packaging materials during
the storage of 15 weeks, and to find the most suitable packaging
material for prolongation of low sugar marmalade candies shelf-life.
An active packaging in combination with modified atmosphere
(MAP, CO2 100%) was examined and compared with traditional
packaging in air ambiance. Polymer Multibarrier 60 and paper bags
were used. Influence of iron based oxygen absorber in sachets of 500
cc obtained from Mitsubishi Gas Chemical Europe Ageless® on the
marmalade candies’ quality was tested during shelf life. Samples of
80±5 g were packaged in polymer pouches (110 mm x 110 mm),
hermetically sealed by MULTIVAC C300 vacuum chamber machine,
and stored in a room temperature +21±0.5 °C. The physiochemical
properties –moisture content, hardness, aw, pH, changes of
atmosphere content (CO2 and O2), ascorbic acid, total carotenoids,
total phenols in headspace of packs, and microbial conditions were
analysed before packaging and in the 1st, 3rd , 5th, 8th, 11th and 15th
weeks of storage.
Abstract: Nowadays, the earth is countered with serious problem
of air pollution. This problem has been started from the industrial
revolution and has been faster in recent years, so that leads the earth
to ecological and environmental disaster. One of its results is the
global warming problem and its related increase in global
temperature. The most important factors in air pollution especially in
urban environments are Automobiles and residential buildings that are
the biggest consumers of the fossil energies, so that if the residential
buildings as a big part of the consumers of such energies reduce their
consumption rate, the air pollution will be decreased. Since
Metropolises are the main centers of air pollution in the world,
assessment and analysis of efficient strategies in decreasing air
pollution in such cities, can lead to the desirable and suitable results
and can solve the problem at least in critical level. Tabriz city is one
of the most important metropolises in North west of Iran that about
two million people are living there. for its situation in cold dry
climate, has a high rate of fossil energies consumption that make air
pollution in its urban environment. These two factors, being both
metropolis and in cold dry climate, make this article try to analyze the
strategies of climatic design in old districts of the city and use them in
new districts of the future. These strategies can be used in this city
and other similar cities and pave the way to reduce energy
consumption and related air pollution to save whole world.
Abstract: A numerical study has been carried out to investigate
the heat transfer by natural convection of nanofluid taking Cu as
nanoparticles and the water as based fluid in a three dimensional
annulus enclosure filled with porous media (silica sand) between two
horizontal concentric cylinders with 12 annular fins of 2.4mm
thickness attached to the inner cylinder under steady state conditions.
The governing equations which used are continuity, momentum and
energy equations under an assumptions used Darcy law and
Boussinesq-s approximation which are transformed to dimensionless
equations. The finite difference approach is used to obtain all the
computational results using the MATLAB-7. The parameters affected
on the system are modified Rayleigh number (10 ≤Ra*≤ 1000), fin
length Hf (3, 7 and 11mm), radius ratio Rr (0.293, 0.365 and 0.435)
and the volume fraction(0 ≤ ¤ò ≤ 0 .35). It was found that the
average Nusselt number depends on (Ra*, Hf, Rr and φ). The results
show that, increasing of fin length decreases the heat transfer rate and
for low values of Ra*, decreasing Rr cause to decrease Nu while for
Ra*
greater than 100, decreasing Rr cause to increase Nu and adding
Cu nanoparticles with 0.35 volume fraction cause 27.9%
enhancement in heat transfer. A correlation for Nu in terms of Ra*,
Hf and φ, has been developed for inner hot cylinder.
Abstract: This paper presents the results of an analytical study
on the seismic response of a Multi-Span-Simply-Supported precast
bridge in Washington State. The bridge was built in the early 1960's
along Interstate 5 and was widened the first time in 1979 and the
second time in 2001. The primary objective of this research project
is to determine the seismic vulnerability of the bridge in order to
develop the required retrofit measure. The seismic vulnerability of
the bridge is evaluated using two seismic evaluation methods
presented in the FHWA Seismic Retrofitting Manual for Highway
Bridges, Method C and Method D2. The results of the seismic
analyses demonstrate that Method C and Method D2 vary markedly
in terms of the information they provide to the bridge designer
regarding the vulnerability of the bridge columns.
Abstract: This paper proposes a simple model of economic geography within the Dixit-Stiglitz-Iceberg framework that may be used to analyze migration patterns among three cities. The cost–benefit tradeoffs affecting incentives for three types of migration, including echelon migration, are discussed. This paper develops a tractable, heterogeneous-agent, general equilibrium model, where agents share constant human capital, and explores the relationship between the benefits of echelon migration and gross human capital. Using Chinese numerical solutions, we study the manifestation of echelon migration and how it responds to changes in transportation cost and elasticity of substitution. Numerical results demonstrate that (i) there are positive relationships between a migration-s benefit-and-wage ratio, (ii) there are positive relationships between gross human capital ratios and wage ratios as to origin and destination, and (iii) we identify 13 varieties of human capital convergence among cities. In particular, this model predicts population shock resulting from the processes of migration choice and echelon migration.
Abstract: The Kowsar dam supply water for different usages
such as drinking, industrial, agricultural and aquaculture farms
usages and located next to the city of Dehdashat in Kohgiluye and
Boyerahmad province in southern Iran. There are some towns and
villages on the Kowsar dam watersheds, which Dehdasht and
Choram are the most important and populated cities in this area. The
study was undertaken to assess the status of water quality in the
urban areas of the Kowsar dam. A total of 28 water samples were
collected from 6 stations on surface water and 1 station from
groundwater on the watershed of the Kowsar dam. All the samples
were analyzed for Cd concentration using standard procedures. The
results were compared with other national and international
standards. Among the analyzed samples, as the maximum value of
cadmium (1.131 μg/L) was observed on the station 2 at the winter
2009, all the samples analyzed were within the maximum admissible
limits by the United States Environmental Protection Agency, EU,
WHO, New Zealand , Australian, Iranian, and the Indian standards.
In general results of the present study have shown that Cd mean
values of stations No. 4, 1 and 2 with 0.5135, 0.0.4733 and 0.4573
μg/L respectively are higher than the other stations . Although Cd
level of all samples and stations have had normal values but this is
an indication of pollution potential and hazards because of human
activity and waste water of towns in the areas, which can effect on
human health implications in future. This research, therefore,
recommends the government and other responsible authorities to take
suitable improving measures in the Kowsar dam watershed-s.
Abstract: Data stream analysis is the process of computing
various summaries and derived values from large amounts of data
which are continuously generated at a rapid rate. The nature of a
stream does not allow a revisit on each data element. Furthermore,
data processing must be fast to produce timely analysis results. These
requirements impose constraints on the design of the algorithms to
balance correctness against timely responses. Several techniques
have been proposed over the past few years to address these
challenges. These techniques can be categorized as either dataoriented
or task-oriented. The data-oriented approach analyzes a
subset of data or a smaller transformed representation, whereas taskoriented
scheme solves the problem directly via approximation
techniques. We propose a hybrid approach to tackle the data stream
analysis problem. The data stream has been both statistically
transformed to a smaller size and computationally approximated its
characteristics. We adopt a Monte Carlo method in the approximation
step. The data reduction has been performed horizontally and
vertically through our EMR sampling method. The proposed method
is analyzed by a series of experiments. We apply our algorithm on
clustering and classification tasks to evaluate the utility of our
approach.
Abstract: The main mission of Ezilla is to provide a friendly
interface to access the virtual machine and quickly deploy the high
performance computing environment. Ezilla has been developed by
Pervasive Computing Team at National Center for High-performance
Computing (NCHC). Ezilla integrates the Cloud middleware,
virtualization technology, and Web-based Operating System (WebOS)
to form a virtual computer in distributed computing environment. In
order to upgrade the dataset and speedup, we proposed the sensor
observation system to deal with a huge amount of data in the
Cassandra database. The sensor observation system is based on the
Ezilla to store sensor raw data into distributed database. We adopt the
Ezilla Cloud service to create virtual machines and login into virtual
machine to deploy the sensor observation system. Integrating the
sensor observation system with Ezilla is to quickly deploy experiment
environment and access a huge amount of data with distributed
database that support the replication mechanism to protect the data
security.
Abstract: Random Oracle Model (ROM) is an effective method
for measuring the practical security of cryptograph. In this paper, we
try to use it into information hiding system (IHS). Because IHS has its
own properties, the ROM must be modified if it is used into IHS.
Firstly, we fully discuss why and how to modify each part of ROM
respectively. The main changes include: 1) Divide the attacks that IHS
may be suffered into two phases and divide the attacks of each phase
into several kinds. 2) Distinguish Oracles and Black-boxes clearly. 3)
Define Oracle and four Black-boxes that IHS used. 4) Propose the
formalized adversary model. And 5) Give the definition of judge.
Secondly, based on ROM of IHS, the security against known original
cover attack (KOCA-KOCA-security) is defined. Then, we give an
actual information hiding scheme and prove that it is
KOCA-KOCA-secure. Finally, we conclude the paper and propose the
open problems of further research.
Abstract: Scatter behavior of fatigue life in die-cast AM60B
alloy was investigated. For comparison, those in rolled AM60B alloy
and die-cast A365-T5 aluminum alloy were also studied. Scatter
behavior of pore size was also investigated to discuss dominant
factors for fatigue life scatter in die-cast materials. Three-parameter
Weibull function was suitable to explain the scatter behavior of both
fatigue life and pore size. The scatter of fatigue life in die-cast
AM60B alloy was almost comparable to that in die-cast A365-T5
alloy, while it was significantly large compared to that in the rolled
AM60B alloy. Scatter behavior of pore size observed at fracture
nucleation site on the fracture surface was comparable to that
observed on the specimen cross-section and also to that of fatigue
life. Therefore, the dominant factor for large scatter of fatigue life in
die-cast alloys would be the large scatter of pore size. This
speculation was confirmed by the fracture mechanics fatigue life
prediction, where the pore observed at fatigue crack nucleation site
was assumed as the pre-existing crack.
Abstract: This paper aims to argue that religion and Faith-based
Organizations (FBOs) contribute to building democratic process
through the provision of education in Sierra Leone. Sierra Leone
experienced a civil war from 1991 to 2002 and about 70 percent of the
population lives in poverty. While the government has been in the
process of rebuilding the nation, many forms of Civil Society
Organizations (CSOs), including FBOs, have played a significant role
in promoting social development. Education plays an important role in
supporting people-s democratic movements through knowledge
acquisition, spiritual enlightenment and empowerment. This paper
discusses religious tolerance in Sierra Leone and how FBOs have
contributed to the provision of primary education in Sierra Leone. This
study is based on the author-s field research, which involved
interviews with teachers and development stakeholders, notably
government officials, Non-governmental Organizations (NGOs) and
FBOs, as well as questionnaires completed by pupils, parents and
teachers.
Abstract: In this paper first, Two buildings have been modeled
and then analyzed using nonlinear static analysis method under two
different conditions in Nonlinear SAP 2000 software. In the first
condition the interaction of soil adjacent to the walls of basement are
ignored while in the second case this interaction have been modeled
using Gap elements of nonlinear SAP2000 software. Finally,
comparing the results of two models, the effects of soil-structure on
period, target point displacement, internal forces, shape deformations
and base shears have been studied. According to the results, this
interaction has always increased the base shear of buildings,
decreased the period of structure and target point displacement, and
often decreased the internal forces and displacements.
Abstract: The draw solute separation process in Forward
Osmosis desalination was simulated in Aspen Plus chemical process
modeling software, to estimate the energy consumption and compare
it with other desalination processes, mainly the Reverse Osmosis
process which is currently most prevalent. The electrolytic chemistry
for the system was retrieved using the Elec – NRTL property method
in the Aspen Plus database. Electrical equivalent of energy required
in the Forward Osmosis desalination technique was estimated and
compared with the prevalent desalination techniques.