Abstract: This study presents a mathematical modeling approach to the planning of HIV therapies on an individual basis. The model replicates clinical data from typical-progressors to AIDS for all stages of the disease with good agreement. Clinical data from rapid-progressors and long-term non-progressors is also matched by estimation of immune system parameters only. The ability of the model to reproduce these phenomena validates the formulation, a fact which is exploited in the investigation of effective therapies. The therapy investigation suggests that, unlike continuous therapy, structured treatment interruptions (STIs) are able to control the increase in both the drug-sensitive and drug-resistant virus population and, hence, prevent the ultimate progression from HIV to AIDS. The optimization results further suggest that even patients characterised by the same progression type can respond very differently to the same treatment and that the latter should be designed on a case-by-case basis. Such a methodology is presented here.
Abstract: This paper describes the gain and noise performances
of discrete Raman amplifier as a function of fiber lengths and the
signal input powers for different pump configurations. Simulation has
been done by using optisystem 7.0 software simulation at signal
wavelength of 1550 nm and a pump wavelength of 1450nm. The
results showed that the gain is higher in bidirectional pumping than in
counter pumping, the gain changes with increasing the fiber length
while the noise figure remain the same for short fiber lengths and the
gain saturates differently for different pumping configuration at
different fiber lengths and power levels of the signal.
Abstract: In this study, an investigation over digestive diseases has been done in which the sound acts as a detector medium. Pursue to the preprocessing the extracted signal in cepstrum domain is registered. After classification of digestive diseases, the system selects random samples based on their features and generates the interest nonstationary, long-term signals via inverse transform in cepstral domain which is presented in digital and sonic form as the output. This structure is updatable or on the other word, by receiving a new signal the corresponding disease classification is updated in the feature domain.
Abstract: We propose a downlink multiple-input multipleoutput
(MIMO) multi-carrier code division multiple access (MCCDMA)
system with adaptive beamforming algorithm for smart
antennas. The algorithm used in this paper is based on the Least
Mean Square (LMS), with pilot channel estimation (PCE) and the
zero forcing equalizer (ZFE) in the receiver, requiring reference
signal and no knowledge channel. MC-CDMA is studied in a
multiple antenna context in order to efficiently exploit robustness
against multipath effects and multi-user flexibility of MC-CDMA and
channel diversity offered by MIMO systems for radio mobile
channels. Computer simulations, considering multi-path Rayleigh
Fading Channel, interference inter symbol and interference are
presented to verify the performance. Simulation results show that the
scheme achieves good performance in a multi-user system.
Abstract: In this paper, we investigate the appearance of the giant component in random subgraphs G(p) of a given large finite graph family Gn = (Vn, En) in which each edge is present independently with probability p. We show that if the graph Gn satisfies a weak isoperimetric inequality and has bounded degree, then the probability p under which G(p) has a giant component of linear order with some constant probability is bounded away from zero and one. In addition, we prove the probability of abnormally large order of the giant component decays exponentially. When a contact graph is modeled as Gn, our result is of special interest in the study of the spread of infectious diseases or the identification of community in various social networks.
Abstract: Much time series data is generally from continuous dynamic system. Firstly, this paper studies the detection of the nonlinearity of time series from continuous dynamics systems by applying the Phase-randomized surrogate algorithm. Then, the Delay Vector Variance (DVV) method is introduced into nonlinearity test. The results show that under the different sampling conditions, the opposite detection of nonlinearity is obtained via using traditional test statistics methods, which include the third-order autocovariance and the asymmetry due to time reversal. Whereas the DVV method can perform well on determining nonlinear of Lorenz signal. It indicates that the proposed method can describe the continuous dynamics signal effectively.
Abstract: Rapid advancement in computing technology brings
computers and humans to be seamlessly integrated in future. The
emergence of smartphone has driven computing era towards
ubiquitous and pervasive computing. Recognizing human activity has
garnered a lot of interest and has raised significant researches-
concerns in identifying contextual information useful to human
activity recognition. Not only unobtrusive to users in daily life,
smartphone has embedded built-in sensors that capable to sense
contextual information of its users supported with wide range
capability of network connections. In this paper, we will discuss the
classification algorithms used in smartphone-based human activity.
Existing technologies pertaining to smartphone-based researches in
human activity recognition will be highlighted and discussed. Our
paper will also present our findings and opinions to formulate
improvement ideas in current researches- trends. Understanding
research trends will enable researchers to have clearer research
direction and common vision on latest smartphone-based human
activity recognition area.
Abstract: It is observed that the Weighted least-square (WLS)
technique, including the modifications, results in equiripple error
curve. The resultant error as a percent of the ideal value is highly
non-uniformly distributed over the range of frequencies for which the
differentiator is designed. The present paper proposes a modification
to the technique so that the optimization procedure results in lower
maximum relative error compared to the ideal values. Simulation
results for first order as well as higher order differentiators are given
to illustrate the excellent performance of the proposed method.
Abstract: A concern that researchers usually face in different
applications of Artificial Neural Network (ANN) is determination of
the size of effective domain in time series. In this paper, trial and
error method was used on groundwater depth time series to determine
the size of effective domain in the series in an observation well in
Union County, New Jersey, U.S. different domains of 20, 40, 60, 80,
100, and 120 preceding day were examined and the 80 days was
considered as effective length of the domain. Data sets in different
domains were fed to a Feed Forward Back Propagation ANN with
one hidden layer and the groundwater depths were forecasted. Root
Mean Square Error (RMSE) and the correlation factor (R2) of
estimated and observed groundwater depths for all domains were
determined. In general, groundwater depth forecast improved, as
evidenced by lower RMSEs and higher R2s, when the domain length
increased from 20 to 120. However, 80 days was selected as the
effective domain because the improvement was less than 1% beyond
that. Forecasted ground water depths utilizing measured daily data
(set #1) and data averaged over the effective domain (set #2) were
compared. It was postulated that more accurate nature of measured
daily data was the reason for a better forecast with lower RMSE
(0.1027 m compared to 0.255 m) in set #1. However, the size of input
data in this set was 80 times the size of input data in set #2; a factor
that may increase the computational effort unpredictably. It was
concluded that 80 daily data may be successfully utilized to lower the
size of input data sets considerably, while maintaining the effective
information in the data set.
Abstract: This study examines perception of environmental
approach in small and medium-sized enterprises (SMEs) – the
process by which firms integrate environmental concern into
business. Based on a review of the literature, the paper synthesizes
focus on environmental issues with the reflection in a case study in
the Czech Republic. Two themes of corporate environmentalism are
discussed – corporate environmental orientation and corporate
stances toward environmental concerns. It provides theoretical
material on greening organizational culture that is helpful in
understanding the response of contemporary business to
environmental problems. We integrate theoretical predictions with
empirical findings confronted with reality. Scales to measure these
themes are tested in a survey of managers in 229 Czech firms. We
used the process of in-depth questioning. The research question was
derived and answered in the context of the corresponding literature
and conducted research. A case study showed us that environmental
approach is variety different (depending on the size of the firm) in
SMEs sector. The results of the empirical mapping demonstrate
Czech company’s approach to environment and define the problem
areas and pinpoint the main limitation in the expansion of
environmental aspects. We contribute to the debate for recognition of
the particular role of environmental issues in business reality.
Abstract: The presence of toxic heavy metals in industrial
effluents is one of the serious threats to the environment. Heavy
metals such as Cadmium, Chromium, Lead, Nickel, Zinc, Mercury,
Copper, Arsenic are found in the effluents of industries such as
foundries, electroplating, petrochemical, battery manufacturing,
tanneries, fertilizer, dying, textiles, metallurgical and metal finishing.
Tremendous increase of industrial copper usage and its presence in
industrial effluents has lead to a growing concern about the fate and
effects of Copper in the environment. Percolation of industrial
effluents through soils leads to contamination of ground water and
soils. The transport of heavy metals and their diffusion into the soils
has therefore, drawn the attention of the researchers.
In this study, an attempt has been made to delineate the
mechanisms of transport and fate of copper in terrestrial
environment. Column studies were conducted using perplex glass
square column of dimension side 15 cm and 1.35 m long. The soil
samples were collected from a natural drain near Mohali (India). The
soil was characterized to be poorly graded sandy loam. The soil was
compacted to the field dry density level of about 1.6 g/cm3. Break
through curves for different depths of the column were plotted. The
results of the column study indicated that the copper has high
tendency to flow in the soils and fewer tendencies to get absorbed on
the soil particles. The t1/2 estimates obtained from the studies can be
used for design copper laden wastewater disposal systems.
Abstract: Residue Number System (RNS) is a modular representation and is proved to be an instrumental tool in many digital signal processing (DSP) applications which require high-speed computations. RNS is an integer and non weighted number system; it can support parallel, carry-free, high-speed and low power arithmetic. A very interesting correspondence exists between the concepts of Multiple Valued Logic (MVL) and Residue Number Arithmetic. If the number of levels used to represent MVL signals is chosen to be consistent with the moduli which create the finite rings in the RNS, MVL becomes a very natural representation for the RNS. There are two concerns related to the application of this Number System: reaching the most possible speed and the largest dynamic range. There is a conflict when one wants to resolve both these problem. That is augmenting the dynamic range results in reducing the speed in the same time. For achieving the most performance a method is considere named “One-Hot Residue Number System" in this implementation the propagation is only equal to one transistor delay. The problem with this method is the huge increase in the number of transistors they are increased in order m2 . In real application this is practically impossible. In this paper combining the Multiple Valued Logic and One-Hot Residue Number System we represent a new method to resolve both of these two problems. In this paper we represent a novel design of an OHRNS-based adder circuit. This circuit is useable for Multiple Valued Logic moduli, in comparison to other RNS design; this circuit has considerably improved the number of transistors and power consumption.
Abstract: The effects of divers carbon substrates were
investigated for the tabtoxin production of an isolated pathogenic
Pseudomonas syringae pv. tabaci, the causal agent of wildfire of
tobacco and are discussed in relation to the bacterium growth. The
isolated organism was grown in batch culture on Woolley's
medium (28°C, 200 rpm, during 5 days). The growth has been
measured by the optical density (OD) at 620 nm and the tabtoxin
production quantified by Escherichia coli (K-12) bioassay
technique. The growth and the tabtoxin production were both
influenced by the substrates (sugars, amino acids, organic acids)
used, each, as a sole carbon source and as a supplement for the
same amino acids. The most significant quantities of tabtoxin were
obtained in presence of some amino acids used as sole carbon
source and/or as supplement.
Abstract: This paper will discuss about an active power generator scheduling method in order to increase the limit level of steady state systems. Some power generator optimization methods such as Langrange, PLN (Indonesian electricity company) Operation, and the proposed Z-Thevenin-based method will be studied and compared in respect of their steady state aspects. A method proposed in this paper is built upon the thevenin equivalent impedance values between each load respected to each generator. The steady state stability index obtained with the REI DIMO method. This research will review the 500kV-Jawa-Bali interconnection system. The simulation results show that the proposed method has the highest limit level of steady state stability compared to other optimization techniques such as Lagrange, and PLN operation. Thus, the proposed method can be used to create the steady state stability limit of the system especially in the peak load condition.
Abstract: Although backpropagation ANNs generally predict
better than decision trees do for pattern classification problems, they
are often regarded as black boxes, i.e., their predictions cannot be
explained as those of decision trees. In many applications, it is
desirable to extract knowledge from trained ANNs for the users to
gain a better understanding of how the networks solve the problems.
A new rule extraction algorithm, called rule extraction from artificial
neural networks (REANN) is proposed and implemented to extract
symbolic rules from ANNs. A standard three-layer feedforward ANN
is the basis of the algorithm. A four-phase training algorithm is
proposed for backpropagation learning. Explicitness of the extracted
rules is supported by comparing them to the symbolic rules generated
by other methods. Extracted rules are comparable with other methods
in terms of number of rules, average number of conditions for a rule,
and predictive accuracy. Extensive experimental studies on several
benchmarks classification problems, such as breast cancer, iris,
diabetes, and season classification problems, demonstrate the
effectiveness of the proposed approach with good generalization
ability.
Abstract: The removal of hydrogen sulphide is required for reasons of health, odour problems, safety and corrosivity problems. The means of removing hydrogen sulphide mainly depend on its concentration and kind of medium to be purified. The paper deals with a method of hydrogen sulphide removal from the air by its catalytic oxidation to elemental sulphur with the use of Fe-EDTA complex. The possibility of obtaining fibrous filtering materials able to remove small concentrations of H2S from the air were described. The base of these materials is fibrous ion exchanger with Fe(III)- EDTA complex immobilized on their functional groups. The complex of trivalent iron converts hydrogen sulphide to elemental sulphur. Bivalent iron formed in the reaction is oxidized by the atmospheric oxygen, so complex of trivalent iron is continuously regenerated and the overall process can be accounted as pseudocatalytic. In the present paper properties of several fibrous catalysts based on ion exchangers with different chemical nature (weak acid,weak base and strong base) were described. It was shown that the main parameters affecting the process of catalytic oxidation are:concentration of hydrogen sulphide in the air, relative humidity of the purified air, the process time and the content of Fe-EDTA complex in the fibres. The data presented show that the filtering layers with anion exchange package are much more active in the catalytic processes of hydrogen sulphide removal than cation exchanger and inert materials. In the addition to the nature of the fibres relative air humidity is a critical factor determining efficiency of the material in the air purification from H2S. It was proved that the most promising carrier of the Fe-EDTA catalyst for hydrogen sulphide oxidation are Fiban A-6 and Fiban AK-22 fibres.
Abstract: During the last couple of years, the degree of dependence on IT systems has reached a dimension nobody imagined to be possible 10 years ago. The increased usage of mobile devices (e.g., smart phones), wireless sensor networks and embedded devices (Internet of Things) are only some examples of the dependency of modern societies on cyber space. At the same time, the complexity of IT applications, e.g., because of the increasing use of cloud computing, is rising continuously. Along with this, the threats to IT security have increased both quantitatively and qualitatively, as recent examples like STUXNET or the supposed cyber attack on Illinois water system are proofing impressively. Once isolated control systems are nowadays often publicly available - a fact that has never been intended by the developers. Threats to IT systems don’t care about areas of responsibility. Especially with regard to Cyber Warfare, IT threats are no longer limited to company or industry boundaries, administrative jurisdictions or state boundaries. One of the important countermeasures is increased cooperation among the participants especially in the field of Cyber Defence. Besides political and legal challenges, there are technical ones as well. A better, at least partially automated exchange of information is essential to (i) enable sophisticated situational awareness and to (ii) counter the attacker in a coordinated way. Therefore, this publication performs an evaluation of state of the art Intrusion Detection Message Exchange protocols in order to guarantee a secure information exchange between different entities.
Abstract: Inter-organizational Workflow (IOW) is commonly
used to support the collaboration between heterogeneous and
distributed business processes of different autonomous organizations
in order to achieve a common goal. E-government is considered as an
application field of IOW. The coordination of the different
organizations is the fundamental problem in IOW and remains the
major cause of failure in e-government projects. In this paper, we
introduce a new coordination model for IOW that improves the
collaboration between government administrations and that respects
IOW requirements applied to e-government. For this purpose, we
adopt a Multi-Agent approach, which deals more easily with interorganizational
digital government characteristics: distribution,
heterogeneity and autonomy. Our model integrates also different
technologies to deal with the semantic and technologic
interoperability. Moreover, it conserves the existing systems of
government administrations by offering a distributed coordination
based on interfaces communication. This is especially applied in
developing countries, where administrations are not necessary
equipped with workflow systems. The use of our coordination
techniques allows an easier migration for an e-government solution
and with a lower cost. To illustrate the applicability of the proposed
model, we present a case study of an identity card creation in Tunisia.
Abstract: Due to the high percentage of induction motors in industrial market, there exist a large opportunity for energy savings. Replacement of working induction motors with more efficient ones can be an important resource for energy savings. A calculation of energy savings and payback periods, as a result of such a replacement, based on nameplate motor efficiency or manufacture-s data can lead to large errors [1]. Efficiency of induction motors (IMs) can be extracted using some procedures that use the no-load test results. In the cases that we must estimate the efficiency on-line, some of these procedures can-t be efficient. In some cases the efficiency estimates using the rating values of the motor, but these procedures can have errors due to the different working condition of the motor. In this paper the efficiency of an IM estimated by using the genetic algorithm. The results are compared with the measured values of the torque and power. The results show smaller errors for this procedure compared with the conventional classical procedures, hence the cost of the equipments is reduced and on-line estimation of the efficiency can be made.
Abstract: The use of radar in Quantitative Precipitation Estimation (QPE) for radar-rainfall measurement is significantly beneficial. Radar has advantages in terms of high spatial and temporal condition in rainfall measurement and also forecasting. In Malaysia, radar application in QPE is still new and needs to be explored. This paper focuses on the Z/R derivation works of radarrainfall estimation based on rainfall classification. The works developed new Z/R relationships for Klang River Basin in Selangor area for three different general classes of rain events, namely low (10mm/hr, 30mm/hr) and also on more specific rain types during monsoon seasons. Looking at the high potential of Doppler radar in QPE, the newly formulated Z/R equations will be useful in improving the measurement of rainfall for any hydrological application, especially for flood forecasting.