Abstract: Personnel protection devices are cardinal in safety hazard applications. They are widely used in home, office and in industry environments to reduce the risk of lethal shock to human being and equipment safety. This paper briefly reviews various personnel protection devices also describes the basic working principle of conventional ground fault circuit interrupter (GFCI) or ground fault isolator (GFI), its disadvantages and ways to overcome the disadvantages with solid-state relay (SSR) based GFI with ultrafast response up on fault implemented in printed circuit board. This solid state GFI comprises discrete MOSFET based alternating current (AC) switches, linear optical amplifier, photovoltaic isolator and sense resistor. In conventional GFI, current transformer is employed as a sensing element to detect the difference in current flow between live and neutral conductor. If there is no fault in equipment powered through GFI, due to insulation failure of internal wires and windings of motors, both live and neutral currents will be equal in magnitude and opposite in phase.
Abstract: Research has suggested that implicit learning tasks
may rely on episodic processing to generate above chance
performance on the standard classification tasks. The current
research examines the invariant features task (McGeorge and Burton,
1990) and argues that such episodic processing is indeed important.
The results of the experiment suggest that both rejection and
similarity strategies are used by participants in this task to
simultaneously reject unfamiliar items and to accept (falsely) familiar
items. Primarily these decisions are based on the presence of low or
high frequency goal based features of the stimuli presented in the
incidental learning phase. It is proposed that a goal based analysis of
the incidental learning task provides a simple step in understanding
which features of the episodic processing are most important for
explaining the match between incidental, implicit learning and test
performance.
Abstract: As there are also graph methods of circuit analysis in
addition to algebraic methods, it is, in theory, clearly possible to
carry out an analysis of a whole switched circuit in two-phase
switching exclusively by the graph method as well. This article deals
with two methods of full-graph solving of switched circuits: by
transformation graphs and by two-graphs. It deals with the circuit
switched capacitors and the switched current, too. All methods are
presented in an equally detailed steps to be able to compare.
Abstract: In this paper, the effect of addition the dune sand powder (DSP) on development of compressive strength and hydration of cement pastes was investigated as a function of water/binder ratio, was varied, on the one hand, the percentage of DSP and on the other, the fineness of DSP. In order to understand better the pozzolanic effect of dune sand powder in cement pastes, we followed the mixtures hydration (50% Pure Lime + 50% DSP) by X-ray diffraction. These mixtures the pastes present a hydraulic setting which is due to the formation of a C-S-H phase (calcium silicate hydrate). The latter is semi-crystallized. This study is a simplified approach to that of the mixtures (80% ordinary Portland cement + 20% DSP), in which the main reaction is the fixing of the lime coming from the cement hydration in the presence of DSP, to form calcium silicate hydrate semi-crystallized of second generation. The results proved that up to (20% DSP) as Portland cement replacement could be used with a fineness of 4000 cm²/g without affecting adversely the compressive strength. After 28 days, the compressive strength at 5, 10 and 15% DSP is superior to Portland cement, with an optimum effect for a percentage of the order of 5% to 10% irrespective of the w/b ratio and fineness of DSP.
Abstract: The paper focuses on the implementation phase of the
strategy of the European Union and the national strategy of the
Czech Republic to promote academic and research staff with the
potential to produce results that provide innovation useful for
economic growth. It deals with the use of financial resources of the
Operational Program Education for Competitiveness at the
University of West Bohemia in Pilsen. The author presents an
example of two strategic projects in the field of human resources –
Excellence in Human Resources as a Source of Competitiveness and
New Excellence of Human Resources. The subject of this paper is the
potential contribution of newly recruited postdoctoral within these
projects for the University of West Bohemia in Pilsen and its internal
environment.
Abstract: Copper based composites reinforced with WC and Ti
particles were prepared using planetary ball-mill. The experiment
was designed by using Taguchi technique and milling was carried out
in an air for several hours. The powder was characterized before and
after milling using the SEM, TEM and X-ray for microstructure and
for possible new phases. Microstructures show that milled particles
size and reduction in particle size depend on many parameters. The
distance d between planes of atoms estimated from X-ray powder
diffraction data and TEM image. X-ray diffraction patterns of the
milled powder did not show clearly any new peak or energy shift, but
the TEM images show a significant change in crystalline structure of
corporate on titanium in the composites.
Abstract: Trace element speciation of an integrated soil
amendment matrix was studied with a modified BCR sequential
extraction procedure. The analysis included pseudo-total
concentration determinations according to USEPA 3051A and
relevant physicochemical properties by standardized methods. Based
on the results, the soil amendment matrix possessed neutralization
capacity comparable to commercial fertilizers. Additionally, the
pseudo-total concentrations of all trace elements included in the
Finnish regulation for agricultural fertilizers were lower than the
respective statutory limit values. According to chemical speciation,
the lability of trace elements increased in the following order: Hg <
Cr < Co < Cu < As < Zn < Ni < Pb < Cd < V < Mo < Ba. The
validity of the BCR approach as a tool for chemical speciation was
confirmed by the additional acid digestion phase. Recovery of trace
elements during the procedure assured the validity of the approach
and indicated good quality of the analytical work.
Abstract: Due to a high unemployment rate among local people
and a high reliance on expatriate workers, the governments in the
Gulf Co-operation Council (GCC) countries have been implementing
programmes of localisation (replacing foreign workers with GCC
nationals). These programmes have been successful in the public
sector but much less so in the private sector. However, there are now
insufficient jobs for locals in the public sector and the onus to provide
employment has fallen on the private sector. This paper is concerned
with a study, which is a work in progress (certain elements are
complete but not the whole study), investigating the effective
implementation of localisation policies in four- and five-star hotels in
the Kingdom of Saudi Arabia (KSA) and the United Arab Emirates
(UAE). The purpose of the paper is to identify the research gap, and
to present the need for the research. Further, it will explain how this
research was conducted.
Studies of localisation in the GCC countries are under-represented
in scholarly literature. Currently, the hotel sectors in KSA and UAE
play an important part in the countries’ economies. However, the
total proportion of Saudis working in the hotel sector in KSA is
slightly under 8%, and in the UAE, the hotel sector remains highly
reliant on expatriates. There is therefore a need for research on
strategies to enhance the implementation of the localisation policies
in general and in the hotel sector in particular.
Further, despite the importance of the hotel sector to their
economies, there remains a dearth of research into the
implementation of localisation policies in this sector. Indeed, as far as
the researchers are aware, there is no study examining localisation in
the hotel sector in KSA, and few in the UAE. This represents a
considerable research gap.
Regarding how the research was carried out, a multiple case study
strategy was used. The four- and five-star hotel sector in KSA is one
of the cases, while the four- and five-star hotel sector in the UAE is
the other case. Four- and five-star hotels in KSA and the UAE were
chosen as these countries have the longest established localisation
policies of all the GCC states and there are more hotels of these
classifications in these countries than in any of the other Gulf
countries. A literature review was carried out to underpin the
research. The empirical data were gathered in three phases. In order
to gain a pre-understanding of the issues pertaining to the research
context, Phase I involved eight unstructured interviews with officials
from the Saudi Commission for Tourism and Antiquities (three
interviewees); the Saudi Human Resources Development Fund (one);
the Abu Dhabi Tourism and Culture Authority (three); and the Abu
Dhabi Development Fund (one).
In Phase II, a questionnaire was administered to 24 managers and
24 employees in four- and five-star hotels in each country to obtain
their beliefs, attitudes, opinions, preferences and practices concerning
localisation.
Unstructured interviews were carried out in Phase III with six
managers in each country in order to allow them to express opinions
that may not have been explored in sufficient depth in the
questionnaire. The interviews in Phases I and III were analysed using
thematic analysis and SPSS will be used to analyse the questionnaire
data.
It is recommended that future research be undertaken on a larger
scale, with a larger sample taken from all over KSA and the UAE
rather than from only four cities (i.e., Riyadh and Jeddah in KSA and
Abu Dhabi and Sharjah in the UAE), as was the case in this research.
Abstract: The existing image coding standards generally degrades at low bit-rates because of the underlying block based Discrete Cosine Transform scheme. Over the past decade, the success of wavelets in solving many different problems has contributed to its unprecedented popularity. Due to implementation constraints scalar wavelets do not posses all the properties such as orthogonality, short support, linear phase symmetry, and a high order of approximation through vanishing moments simultaneously, which are very much essential for signal processing. New class of wavelets called 'Multiwavelets' which posses more than one scaling function overcomes this problem. This paper presents a new image coding scheme based on non linear approximation of multiwavelet coefficients along with multistage vector quantization. The performance of the proposed scheme is compared with the results obtained from scalar wavelets.
Abstract: This study deals with the experimental investigation
and theoretical modeling of Semi crystalline polymeric materials with
a rubbery amorphous phase (HDPE) subjected to a uniaxial cyclic
tests with various maximum strain levels, even at large deformation.
Each cycle is loaded in tension up to certain maximum strain and
then unloaded down to zero stress with N number of cycles. This
work is focuses on the measure of the volume strain due to the
phenomena of damage during this kind of tests. On the basis of
thermodynamics of relaxation processes, a constitutive model for
large strain deformation has been developed, taking into account the
damage effect, to predict the complex elasto-viscoelastic-viscoplastic
behavior of material. A direct comparison between the model
predictions and the experimental data show that the model accurately
captures the material response. The model is also capable of
predicting the influence damage causing volume variation.
Abstract: A new topology of unified power quality conditioner
(UPQC) is proposed for different power quality (PQ) improvement in
a three-phase four-wire (3P-4W) distribution system. For neutral
current mitigation, a star-hexagon transformer is connected in shunt
near the load along with three-leg voltage source inverters (VSIs)
based UPQC. For the mitigation of source neutral current, the uses of
passive elements are advantageous over the active compensation due
to ruggedness and less complexity of control. In addition to this, by
connecting a star-hexagon transformer for neutral current mitigation
the over all rating of the UPQC is reduced. The performance of the
proposed topology of 3P-4W UPQC is evaluated for power-factor
correction, load balancing, neutral current mitigation and mitigation
of voltage and currents harmonics. A simple control algorithm based
on Unit Vector Template (UVT) technique is used as a control
strategy of UPQC for mitigation of different PQ problems. In this
control scheme, the current/voltage control is applied over the
fundamental supply currents/voltages instead of fast changing APFs
currents/voltages, thereby reducing the computational delay.
Moreover, no extra control is required for neutral source current
compensation; hence the numbers of current sensors are reduced. The
performance of the proposed topology of UPQC is analyzed through
simulations results using MATLAB software with its Simulink and
Power System Block set toolboxes.
Abstract: Isobaric and cooling zone of iron ore reactor have been
simulated. In this paper, heat and mass transfer equation are
formulated to perform the temperature and concentration of gas and
solid phase respectively. Temperature profile for isobaric zone is
simulated on the range temperature of 873-1163K while cooling zone
is simulated on the range temperature of 733-1139K. The simulation
results have a good agreement with the plant data. Total carbon
formation in the isobaric zone is only 30% of total carbon contained in
the sponge iron product. The formation of Fe3C in isobaric zone
reduces metallization degree up to 0.58% whereas reduction of
metallization degree in cooling zone up to 1.139%. The decreasing of
sponge iron temperature in the isobaric and cooling zone is around 300
K and 600 K respectively.
Abstract: Globalization and therefore increasing tight competition among companies, have resulted to increase the importance of making well-timed decision. Devising and employing effective strategies, that are flexible and adaptive to changing market, stand a greater chance of being effective in the long-term. In other side, a clear focus on managing the entire product lifecycle has emerged as critical areas for investment. Therefore, applying wellorganized tools to employ past experience in new case, helps to make proper and managerial decisions. Case based reasoning (CBR) is based on a means of solving a new problem by using or adapting solutions to old problems. In this paper, an adapted CBR model with k-nearest neighbor (K-NN) is employed to provide suggestions for better decision making which are adopted for a given product in the middle of life phase. The set of solutions are weighted by CBR in the principle of group decision making. Wrapper approach of genetic algorithm is employed to generate optimal feature subsets. The dataset of the department store, including various products which are collected among two years, have been used. K-fold approach is used to evaluate the classification accuracy rate. Empirical results are compared with classical case based reasoning algorithm which has no special process for feature selection, CBR-PCA algorithm based on filter approach feature selection, and Artificial Neural Network. The results indicate that the predictive performance of the model, compare with two CBR algorithms, in specific case is more effective.
Abstract: Macrophomina phaseolina is a devastating soil-borne
fungal plant pathogen that causes charcoal rot disease in many
economically important crops worldwide. So far, no registered
fungicide is available against this plant pathogen. This study was
planned to examine the antifungal activity of an allelopathic grass
Cenchrus pennisetiformis (Hochst. & Steud.) Wipff. for the
management of M. phaseolina isolated from cowpea [Vigna
unguiculata (L.) Walp.] plants suffering from charcoal rot disease.
Different parts of the plants viz. inflorescence, shoot and root were
extracted in methanol. Laboratory bioassays were carried out using
different concentrations (0, 0.5, 1.0, …, 3.0 g mL-1) of methanolic
extracts of the test allelopathic grass species to assess the antifungal
activity against the pathogen. In general, extracts of all parts of the
grass exhibited antifungal activity. All the concentrations of
methanolic extracts of shoot and root significantly reduced fungal
biomass by 20–73% and 40–80%, respectively. Methanolic shoot
extract was fractionated using n-hexane, chloroform, ethyl acetate
and n-butanol. Different concentrations of these fractions (3.125,
6.25, …, 200 mg mL-1) were analyzed for their antifungal activity.
All the concentrations of n-hexane fraction significantly reduced
fungal biomass by 15–96% over corresponding control treatments.
Higher concentrations (12.5–200 mg mL-1) of chloroform, ethyl
acetate and n-butanol also reduced the fungal biomass significantly
by 29–100%, 46–100% and 24–100%, respectively.
Abstract: A cart-ball system is a challenging system from the
control engineering point of view. This is due to the nonlinearities,
multivariable, and non-minimum phase behavior present in this
system. This paper is concerned with the problem of modeling and
control of such system. The objective of control strategy is to place
the cart at a desired position while balancing the ball on the top of the
arc-shaped track fixed on the cart. A State-Feedback Controller
(SFC) with a pole-placement method will be designed in order to
control the system. At first, the mathematical model of a cart-ball
system in the state-space form is developed. Then, the linearization of
a model will be established in order to design a SFC. The integral
control strategy will be performed as to control the cart position of a
system. Simulation work is then performed using
MATLAB/SIMULINK software in order to study the performance of
SFC when applied to the system.
Abstract: A predictive clustering hybrid regression (pCHR)
approach was developed and evaluated using dataset from H2-
producing sucrose-based bioreactor operated for 15 months. The aim
was to model and predict the H2-production rate using information
available about envirome and metabolome of the bioprocess. Selforganizing
maps (SOM) and Sammon map were used to visualize the
dataset and to identify main metabolic patterns and clusters in
bioprocess data. Three metabolic clusters: acetate coupled with other
metabolites, butyrate only, and transition phases were detected. The
developed pCHR model combines principles of k-means clustering,
kNN classification and regression techniques. The model performed
well in modeling and predicting the H2-production rate with mean
square error values of 0.0014 and 0.0032, respectively.
Abstract: Study of fire and explosion is very important mainly
in oil and gas industries due to several accidents which have been
reported in the past and present. In this work, we have investigated
the flammability of bio oil vapour mixtures. This mixture may
contribute to fire during the storage and transportation process. Bio
oil sample derived from Palm Kernell shell was analysed using Gas
Chromatography Mass Spectrometry (GC-MS) to examine the
composition of the sample. Mole fractions of 12 selected
components in the liquid phase were obtained from the GC-FID data
and used to calculate mole fractions of components in the gas phase
via modified Raoult-s law. Lower Flammability Limits (LFLs) and
Upper Flammability Limits (UFLs) for individual components were
obtained from published literature. However, stoichiometric
concentration method was used to calculate the flammability limits
of some components which their flammability limit values are not
available in the literature. The LFL and UFL values for the mixture
were calculated using the Le Chatelier equation. The LFLmix and
UFLmix values were used to construct a flammability diagram and
subsequently used to determine the flammability of the mixture. The
findings of this study can be used to propose suitable inherently
safer method to prevent the flammable mixture from occurring and
to minimizing the loss of properties, business, and life due to fire
accidents in bio oil productions.
Abstract: Through inward perceptions, we intuitively expect
distributed software development to increase the risks associated with
achieving cost, schedule, and quality goals. To compound this
problem, agile software development (ASD) insists one of the main
ingredients of its success is cohesive communication attributed to
collocation of the development team. The following study identified
the degree of communication richness needed to achieve comparable
software quality (reduce pre-release defects) between distributed and
collocated teams. This paper explores the relevancy of
communication richness in various development phases and its
impact on quality. Through examination of a large distributed agile
development project, this investigation seeks to understand the levels
of communication required within each ASD phase to produce
comparable quality results achieved by collocated teams. Obviously,
a multitude of factors affects the outcome of software projects.
However, within distributed agile software development teams, the
mode of communication is one of the critical components required to
achieve team cohesiveness and effectiveness. As such, this study
constructs a distributed agile communication model (DAC-M) for
potential application to similar distributed agile development efforts
using the measurement of the suitable level of communication. The
results of the study show that less rich communication methods, in
the appropriate phase, might be satisfactory to achieve equivalent
quality in distributed ASD efforts.
Abstract: The storage of thermal energy as a latent heat of phase
change material (PCM) has created considerable interest among
researchers in recent times. Here, an attempt is made to carry out
numerical investigations to analyze the performance of latent heat
storage units (LHSU) employing phase change material. The
mathematical model developed is based on an enthalpy formulation.
Freezing time of PCM packed in three different shaped containers
viz. rectangular, cylindrical and cylindrical shell is compared. The
model is validated with the results available in the literature. Results
show that for the same mass of PCM and surface area of heat
transfer, cylindrical shell container takes the least time for freezing
the PCM and this geometric effect is more pronounced with an
increase in the thickness of the shell than that of length of the shell.
Abstract: Saturated hydraulic conductivity is one of the soil
hydraulic properties which is widely used in environmental studies
especially subsurface ground water. Since, its direct measurement is
time consuming and therefore costly, indirect methods such as
pedotransfer functions have been developed based on multiple linear
regression equations and neural networks model in order to estimate
saturated hydraulic conductivity from readily available soil
properties e.g. sand, silt, and clay contents, bulk density, and organic
matter. The objective of this study was to develop neural networks
(NNs) model to estimate saturated hydraulic conductivity from
available parameters such as sand and clay contents, bulk density,
van Genuchten retention model parameters (i.e. r
θ , α , and n) as well
as effective porosity. We used two methods to calculate effective
porosity: : (1) eff s FC φ =θ -θ , and (2) inf φ =θ -θ eff s , in which s
θ is
saturated water content, FC θ is water content retained at -33 kPa
matric potential, and inf θ is water content at the inflection point.
Total of 311 soil samples from the UNSODA database was divided
into three groups as 187 for the training, 62 for the validation (to
avoid over training), and 62 for the test of NNs model. A commercial
neural network toolbox of MATLAB software with a multi-layer
perceptron model and back propagation algorithm were used for the
training procedure. The statistical parameters such as correlation
coefficient (R2), and mean square error (MSE) were also used to
evaluate the developed NNs model. The best number of neurons in
the middle layer of NNs model for methods (1) and (2) were
calculated 44 and 6, respectively. The R2 and MSE values of the test
phase were determined for method (1), 0.94 and 0.0016, and for
method (2), 0.98 and 0.00065, respectively, which shows that method
(2) estimates saturated hydraulic conductivity better than method (1).