Abstract: The Principal component regression (PCR) is a
combination of principal component analysis (PCA) and multiple linear regression (MLR). The objective of this paper is to revise the
use of PCR in shortwave near infrared (SWNIR) (750-1000nm) spectral analysis. The idea of PCR was explained mathematically and
implemented in the non-destructive assessment of the soluble solid
content (SSC) of pineapple based on SWNIR spectral data. PCR achieved satisfactory results in this application with root mean
squared error of calibration (RMSEC) of 0.7611 Brix°, coefficient of determination (R2) of 0.5865 and root mean squared error of crossvalidation
(RMSECV) of 0.8323 Brix° with principal components
(PCs) of 14.
Abstract: In this study three commercial semiconductor devices
were characterized in the laboratory for computed tomography
dosimetry: one photodiode and two phototransistors. It was evaluated
four responses to the irradiation: dose linearity, energy dependence,
angular dependence and loss of sensitivity after X ray exposure. The
results showed that the three devices have proportional response with
the air kerma; the energy dependence displayed for each device
suggests that some calibration factors would be applied for each one;
the angular dependence showed a similar pattern among the three
electronic components. In respect to the fourth parameter analyzed,
one phototransistor has the highest sensitivity however it also showed
the greatest loss of sensitivity with the accumulated dose. The
photodiode was the device with the smaller sensitivity to radiation,
on the other hand, the loss of sensitivity after irradiation is negligible.
Since high accuracy is a desired feature for a dosimeter, the
photodiode can be the most suitable of the three devices for
dosimetry in tomography. The phototransistors can also be used for
CT dosimetry, however it would be necessary a correction factor due
to loss of sensitivity with accumulated dose.
Abstract: Four different colors of cowpeas (Vigna unguiculata)
(black, white, red and black/white speckled) and red kidney bean
(Phaseolus vulgaris) were used to evaluate proximate compositions,
starch content, and pasting properties. There were no significant
differences of moisture, protein, ash, fat, and carbohydrate contents
of all bean types. The kidney bean had significantly lower amounts of
total starch and solubilized starch compared to those of other
cowpeas (p ≤ 0.05), whereas the red cowpea and red kidney bean had
highest content of resistant starch (9-10%). Decortication indicated
no significant effect on the proximate compositions of all samples,
but it significantly decreased the resistant starch content in cowpeas
and increased the solubilized starch and total starch content in all
types of cowpeas. The highest values of pasting properties, generally
observed in flours obtained from black and black/white speckled
cowpea.
Abstract: The aim of this paper is to investigate twodimensional unsteady flow of a viscous incompressible fluid about stagnation point on permeable stretching sheet in presence of time dependent free stream velocity. Fluid is considered in the influence of transverse magnetic field in the presence of radiation effect. Rosseland approximation is use to model the radiative heat transfer. Using time-dependent stream function, partial differential equations corresponding to the momentum and energy equations are converted into non-linear ordinary differential equations. Numerical solutions of these equations are obtained by using Runge-Kutta Fehlberg method with the help of Newton-Raphson shooting technique. In the present work the effect of unsteadiness parameter, magnetic field parameter, radiation parameter, stretching parameter and the Prandtl number on flow and heat transfer characteristics have been discussed. Skin-friction coefficient and Nusselt number at the sheet are computed and discussed. The results reported in the paper are in good agreement with published work in literature by other researchers.
Abstract: Tailor-welded Blanks (TWBs) are tailor made for
different complex component designs by welding multiple metal
sheets with different thicknesses, shapes, coatings or strengths prior
to forming. In this study the Hemispherical Die Stretching (HDS) test
(out-of-plane stretching) of TWBs were simulated via
ABAQUS/Explicit to obtain the Forming Limit Diagrams (FLDs) of
Stainless steel (AISI 304) laser welded blanks with different
thicknesses. Two criteria were used to detect the start of necking to
determine the FLD for TWBs and parent sheet metals. These two
criteria are the second derivatives of the major and thickness strains
that are given from the strain history of simulation. In the other word,
in these criteria necking starts when the second derivative of
thickness or major strain reaches its maximum. With having the time
of onset necking, one can measure the major and minor strains at the
critical area and determine the forming limit curve.
Abstract: An application framework provides a reusable
design and implementation for a family of software systems.
Frameworks are introduced to reduce the cost of a product line
(i.e., family of products that share the common features). Software
testing is a time consuming and costly ongoing activity during the
application software development process. Generating reusable test
cases for the framework applications at the framework
development stage, and providing and using the test cases to test
part of the framework application whenever the framework is used
reduces the application development time and cost considerably.
Framework Interface Classes (FICs) are classes introduced by
the framework hooks to be implemented at the application
development stage. They can have reusable test cases generated at
the framework development stage and provided with the
framework to test the implementations of the FICs at the
application development stage. In this paper, we conduct a case
study using thirteen applications developed using three
frameworks; one domain oriented and two application oriented.
The results show that, in general, the percentage of the number of
FICs in the applications developed using domain frameworks is, on
average, greater than the percentage of the number of FICs in the
applications developed using application frameworks.
Consequently, the reduction of the application unit testing time
using the reusable test cases generated for domain frameworks is,
in general, greater than the reduction of the application unit testing
time using the reusable test cases generated for application
frameworks.
Abstract: In this paper, a near lossless image coding scheme
based on Orthogonal Polynomials Transform (OPT) has been
presented. The polynomial operators and polynomials basis operators
are obtained from set of orthogonal polynomials functions for the
proposed transform coding. The image is partitioned into a number of
distinct square blocks and the proposed transform coding is applied to
each of these individually. After applying the proposed transform
coding, the transformed coefficients are rearranged into a sub-band
structure. The Embedded Zerotree (EZ) coding algorithm is then
employed to quantize the coefficients. The proposed transform is
implemented for various block sizes and the performance is
compared with existing Discrete Cosine Transform (DCT) transform
coding scheme.
Abstract: One of the most important issues in multi-criteria decision analysis (MCDA) is to determine the weights of criteria so that all alternatives can be compared based on the collective performance of criteria. In this paper, one of popular methods in data envelopment analysis (DEA) known as common weights (CWs) is used to determine the weights in MCDA. Two frontiers named ideal and anti-ideal frontiers, instead of ideal and anti-ideal alternatives, are defined based on two new proposed CWs models. Ideal and antiideal frontiers are more flexible than that of alternatives. According to the optimal solutions of these two models, the distances of an alternative from the ideal and anti-ideal frontiers are derived. Then, a relative distance is introduced to measure the value of each alternative. The suggested models are linear and despite weight restrictions are feasible. An example is presented for explaining the method and for comparing to the existing literature.
Abstract: DNA microarray technology is widely used by
geneticists to diagnose or treat diseases through gene expression.
This technology is based on the hybridization of a tissue-s DNA
sequence into a substrate and the further analysis of the image
formed by the thousands of genes in the DNA as green, red or yellow
spots. The process of DNA microarray image analysis involves
finding the location of the spots and the quantification of the
expression level of these. In this paper, a tool to perform DNA
microarray image analysis is presented, including a spot addressing
method based on the image projections, the spot segmentation
through contour based segmentation and the extraction of relevant
information due to gene expression.
Abstract: New software protection product called “Obfuscation
Studio" is presented in the paper. Several obfuscating modules that
are already implemented are described. Some theoretical data is
presented, that shows the potency and effectiveness of described
obfuscation methods. “Obfuscation Studio" is being implemented for
protecting programs written for .NET platform, but the described
methods can also be interesting for other applications.
Abstract: The nanotechnology based on epitaxial systems
includes single or arranged misfit dislocations. In general, whatever
is the type of dislocation or the geometry of the array formed by the
dislocations; it is important for experimental studies to know exactly
the stress distribution for which there is no analytical expression [1,
2]. This work, using a numerical analysis, deals with relaxation of
epitaxial layers having at their interface a periodic network of edge
misfit dislocations. The stress distribution is estimated by using
isotropic elasticity. The results show that the thickness of the two
sheets is a crucial parameter in the stress distributions and then in the
profile of the two sheets.
A comparative study between the case of single dislocation and
the case of parallel network shows that the layers relaxed better when
the interface is covered by a parallel arrangement of misfit.
Consequently, a single dislocation at the interface produces an
important stress field which can be reduced by inserting a parallel
network of dislocations with suitable periodicity.
Abstract: An attempt has been made to beneficiate the Indian
coking coal fines by a combination of Spiral, flotation and Oleo
Flotation processes. Beneficiation studies were also carried out on -
0.5mm coal fines using flotation and oleo flotation by splitting at size
0.063mm.Size fraction of 0.5mm-0.063mm and -0.063mm size were
treated in flotation and Oleo flotation respectively. The washability
studies on the fraction 3-0.5 mm indicated that good separation may
be achieved when it is fed in a spiral. Combined product of Spiral,
Flotation and Oleo Flotation has given a significant yield at
acceptable ash%. Studies were also conducted to see the dewatering
of combined product by batch type centrifuge. It may further be
suggested that combination of different processes may be used to
treat the -3 mm fraction in an integrated manner to achieve the yield
at the desired ash level. The treatment of the 3/1 mm -0.5 mm size
fraction by spiral,-0.5-0.63 mm by conventional froth flotation and -
0.063 fractions by oleo flotation may provide a complete solution of
beneficiation and dewatering of coal fines, and can effectively
address the environmental problems caused by coal fines.
Abstract: The High Voltage (HV) transmission mains into the community necessitate earthing design to ensure safety compliance of the system. Concrete poles are widely used within HV transmission mains; which could have an impact on the earth grid impedance and input impedance of the system from the fault point of view. This paper provides information on concrete pole earthing to enhance the split factor of the system; further, it discusses the deployment of concrete structures in high soil resistivity area to reduce the earth grid system of the plant. This paper introduces the cut off soil resistivity SC ρ when replacing timber poles with concrete ones.
Abstract: After Apple's first introduction its smart phone, iPhone
in the end of 2009 in Korea, the number of Korean smarphone users
had been rapidly increasing so that the half of Korean population
became smart phone users as of February, 2012. Currently, smart
phones are positioned as a major digital media with powerful
influences in Korea. And, now, Koreans are leaning new information,
enjoying games and communicating other people every time and
everywhere. As smart phone devices' performances increased, the
number of usable services became more while adequate GUI
developments are required to implement various functions with smart
phones. The strategy to provide similar experiences on smart phones
through familiar features based on employment of existing media's
functions mostly contributed to smart phones' popularization in
connection with smart phone devices' iconic GUIs.
The spread of Smart phone increased mobile web accesses.
Therefore, the attempts to implement PC's web in the smart phone's
web are continuously made. The mobile web GUI provides familiar
experiences to users through designs adequately utilizing the smart
phone's GUIs. As the number of users familiarized to smart phones
and mobile web GUIs, opposite to reversed remediation from many
parts of PCs, PCs are starting to adapt smart phone GUIs.
This study defines this phenomenon as the reversed remediation,
and reviews the reversed remediation cases of Smart phone GUI'
characteristics of PCs. For this purpose, the established study issues
are as under:
· what is the reversed remediation?
· what are the smart phone GUI's characteristics?
· what kind of interrelationship exist s between the smart phone and
PC's web site?
It is meaningful in the forecast of the future GUI's change by
understanding of characteristics in the paradigm changes of PC and
smart phone's GUI designs. This also will be helpful to establish
strategies for digital devices' development and design.
Abstract: The study attempted to identify the dominant
intelligences of athletes by comparing the developmental differences
of multiple intelligences between athletes and non-athletes. The
weekly specialized training hours and years of specialized training
was examined to see how it can predict the dominant intelligence with
the age factor controlled. There were 355 participants in the research
(202 athletes and 153 non-athletes). Collected data were analyzed with
one-way MANOVA and multiple hierarchical regression. The results
suggested the dominant intelligences of athletes were Interpersonal
Intelligence, Bodily-Kinesthetic Intelligence, and Intrapersonal
Intelligence. The weekly specialized training hours and years of
specialized training could effectively predict the Interpersonal
Intelligence, Bodily-Kinesthetic Intelligence, and Intrapersonal
Intelligence of athletes. The author suggested the future studies could
focus on the theory construction of weekly specialized training and
years of specialized training. Also, the studies on using “Bridge
strategy" by the athletes to guide disadvantage intelligences with
dominant intelligences are highly valued.
Abstract: Aim. We have introduced the notion of order to multinormed spaces and countable union spaces and their duals. The topology of bounded convergence is assigned to the dual spaces. The aim of this paper is to develop the theory of ordered topological linear
spaces La,b, L(w, z), the dual spaces of ordered multinormed spaces
La,b, ordered countable union spaces L(w, z), with the topology of bounded convergence assigned to the dual spaces. We apply Laplace transformation to the ordered linear space of Laplace transformable
generalized functions. We ultimately aim at finding solutions to nonhomogeneous
nth order linear differential equations with constant
coefficients in terms of generalized functions and comparing different
solutions evolved out of different initial conditions.
Method. The above aim is achieved by
• Defining the spaces La,b, L(w, z).
• Assigning an order relation on these spaces by identifying a
positive cone on them and studying the properties of the cone.
• Defining an order relation on the dual spaces La,b, L(w, z) of La,b, L(w, z) and assigning a topology to these dual spaces which makes the order dual and the topological dual the same. • Defining the adjoint of a continuous map on these spaces
and studying its behaviour when the topology of bounded
convergence is assigned to the dual spaces.
• Applying the two-sided Laplace Transformation on the ordered
linear space of generalized functions W and studying some
properties of the transformation which are used in solving
differential equations.
Result. The above techniques are applied to solve non-homogeneous
n-th order linear differential equations with constant coefficients in
terms of generalized functions and to compare different solutions of the differential equation.
Abstract: Research in e-Business has been growing
tremendously covering all related aspects such as adoption issues, e-
Business models, strategies, etc. This research aims to explore the
potential of adopting e-Business for a micro size business operating
from home called home-based businesses (HBBs). In Malaysia, the
HBB industry started many years ago and were mostly monopolized
by women or housewives managed as a part-time job to support their
family economy. Today, things have changed. The availability of the
Internet technology and the emergence of e-Business concept
promote the evolution of HBBs, which have been adopted as another
alternative as a professional career for women without neglecting
their family needs especially the children. Although this study is
confined to a limited sample size and within geographical biasness,
the findings show that it concurs with previous large scale studies. In
this study, both qualitative and quantitative methods were used and
data were gathered using triangulation methods via interview, direct
observation, document analysis and survey questionnaires. This paper
discusses the literature review, research methods and findings
pertaining to e-Business adoption factors that influence the HBBs in
Malaysia.
Abstract: In this paper we introduce a new unit test technique
called déjà-vu object. Déjà-vu objects replace real objects used by
classes under test, allowing the execution of isolated unit tests. A
déjà-vu object is able to observe and record the behaviour of a real
object during real sessions, and to replace it during unit tests,
returning previously recorded results. Consequently déjà-vu object
technique can be useful when a bottom-up development and testing
strategy is adopted. In this case déjà-vu objects can increase test
portability and test source code readability. At the same time they
can reduce the time spent by programmers to develop test code and
the risk of incompatibility during the switching between déjà-vu and
production code.
Abstract: In order to consider the effects of the higher modes in
the pushover analysis, during the recent years several multi-modal
pushover procedures have been presented. In these methods the
response of the considered modes are combined by the square-rootof-
sum-of-squares (SRSS) rule while application of the elastic modal
combination rules in the inelastic phases is no longer valid. In this
research the feasibility of defining an efficient alternative
combination method is investigated. Two steel moment-frame
buildings denoted SAC-9 and SAC-20 under ten earthquake records
are considered. The nonlinear responses of the structures are
estimated by the directed algebraic combination of the weighted
responses of the separate modes. The weight of the each mode is
defined so that the resulted response of the combination has a
minimum error to the nonlinear time history analysis. The genetic
algorithm (GA) is used to minimize the error and optimize the weight
factors. The obtained optimal factors for each mode in different cases
are compared together to find unique appropriate weight factors for
each mode in all cases.
Abstract: Liveable city is referred to as the quality of life in an
area that contributes towards a safe, healthy and enjoyable place. This
paper discusses the role of the streets- activities in making Kuala
Lumpur a liveable city and the happiness level of the residents
towards the city-s street activities. The study was conducted using the
residents of Kuala Lumpur. A mixed method technique is used with
the quantitative data as a main data and supported by the qualitative
data. Data were collected using questionnaires, observation and also
an interview session with a sample of residents of Kuala Lumpur.
The sampling technique is based on multistage cluster data sampling.
The findings revealed that, there is still no significant relationship
between the length of stay of the resident in Kuala Lumpur with the
happiness level towards the street activities that occurred in the city.