Abstract: This paper looks into detailed investigation of
thermal-hydraulic characteristics of the flow field in a fuel rod
model, especially near the spacer. The area investigate represents a
source of information on the velocity flow field, vortex, and on the
amount of heat transfer into the coolant all of which are critical for
the design and improvement of the fuel rod in nuclear power plants.
The flow field investigation uses three-dimensional Computational
Fluid Dynamics (CFD) with the Reynolds stresses turbulence model
(RSM). The fuel rod model incorporates a vertical annular channel
where three different shapes of spacers are used; each spacer shape is
addressed individually. These spacers are mutually compared in
consideration of heat transfer capabilities between the coolant and
the fuel rod model. The results are complemented with the calculated
heat transfer coefficient in the location of the spacer and along the
stainless-steel pipe.
Abstract: The major problem that wireless communication
systems undergo is multipath fading caused by scattering of the
transmitted signal. However, we can treat multipath propagation as
multiple channels between the transmitter and receiver to improve
the signal-to-scattering-noise ratio. While using Single Input
Multiple Output (SIMO) systems, the diversity receivers extract
multiple signal branches or copies of the same signal received from
different channels and apply gain combining schemes such as Root
Mean Square Gain Combining (RMSGC). RMSGC asymptotically
yields an identical performance to that of the theoretically optimal
Maximum Ratio Combining (MRC) for values of mean Signal-to-
Noise-Ratio (SNR) above a certain threshold value without the need
for SNR estimation. This paper introduces an improvement of
RMSGC using two different issues. We found that post-detection and
de-noising the received signals improve the performance of RMSGC
and lower the threshold SNR.
Abstract: This document details the process of developing a
wireless device that captures the basic movements of the foot (plantar
flexion, dorsal flexion, abduction, adduction.), and the knee
movement (flexion). It implements a motion capture system by using
a hardware based on optical fiber sensors, due to the advantages in
terms of scope, noise immunity and speed of data transmission and
reception. The operating principle used by this system is the detection
and transmission of joint movement by mechanical elements and
their respective measurement by optical ones (in this case infrared).
Likewise, Visual Basic software is used for reception, analysis and
signal processing of data acquired by the device, generating a 3D
graphical representation in real time of each movement. The result is
a boot in charge of capturing the movement, a transmission module
(Implementing Xbee Technology) and a receiver module for
receiving information and sending it to the PC for their respective
processing.
The main idea with this device is to help on topics such as
bioengineering and medicine, by helping to improve the quality of
life and movement analysis.
Abstract: Building intelligent traffic guide systems has been an
interesting subject recently. A good system should be able to observe
all important visual information to be able to analyze the context of
the scene. To do so, signs in general, and traffic signs in particular,
are usually taken into account as they contain rich information to
these systems. Therefore, many researchers have put an effort on
sign recognition field. Sign localization or sign detection is the most
important step in the sign recognition process. This step filters out
non informative area in the scene, and locates candidates in later
steps. In this paper, we apply a new approach in detecting sign
locations using a new color invariant model. Experiments are carried
out with different datasets introduced in other works where authors
claimed the difficulty in detecting signs under unfavorable imaging
conditions. Our method is simple, fast and most importantly it gives
a high detection rate in locating signs.
Abstract: Retention in the IT profession is critical for
organizations to stay competitive and operate reliably in the dynamic
business environment. Most organizations rely on compensation and
rewards as primary tools to enhance retention of employees. In this
quantitative survey-based study conducted at a large global bank, we
analyze the perceptions of 575 information technology (IT) software
professionals in India and Malaysia and find that fairness of rewards
has very little impact on retention likelihood. It is far more important
to actively involve employees in organizational activities. In
addition, our findings indicate that involvement is far more important
than information flow: the typical organizational communication to
keep employees informed.
Abstract: Electrical Discharge Machine (EDM) is especially
used for the manufacturing of 3-D complex geometry and hard
material parts that are extremely difficult-to-machine by conventional
machining processes. In this paper authors review the research work
carried out in the development of die-sinking EDM within the past
decades for the improvement of machining characteristics such as
Material Removal Rate, Surface Roughness and Tool Wear Ratio. In
this review various techniques reported by EDM researchers for
improving the machining characteristics have been categorized as
process parameters optimization, multi spark technique, powder
mixed EDM, servo control system and pulse discriminating. At the
end, flexible machine controller is suggested for Die Sinking EDM to
enhance the machining characteristics and to achieve high-level
automation. Thus, die sinking EDM can be integrated with Computer
Integrated Manufacturing environment as a need of agile
manufacturing systems.
Abstract: In this paper, in order to investigate the effects of
photovoltaic system introduction to detached houses in Japan, two
kinds of works were done. Firstly, the hourly generation amount of a
4.2kW photovoltaic system were simulated in 46 cities to investigate
the potential of the system in different regions in Japan using a
simulation model of photovoltaic system. Secondly, based on the
simulated electricity generation amount, the energy saving, the
environmental and the economic effect of the photovoltaic system
were examined from hourly to annual timescales, based upon
calculations of typical electricity, heating, cooling and hot water
supply load profiles for Japanese dwellings. The above analysis was
carried out using a standard year-s hourly weather data for the
different city provided by the Expanded AMeDAS Weather Data
issued by AIJ (Architectural Institute of Japan).
Abstract: To investigate the possible correlation between peer aggression and peer victimization, 148 sixth-graders were asked to respond to the Reduced Aggression and Victimization Scales (RAVS). RAVS measures the frequency of reporting aggressive behaviors or of being victimized during the previous week prior to the survey. The scales are composed of six items each. Each point represents one instance of aggression or victimization. Specifically, the Pearson Product-Moment Correlation Coefficient (PMCC) was used to determine the correlations between the scores of the sixthgraders in the two scales, both in individual items and total scores. Positive correlations were established and correlations were significant at the 0.01 levels.
Abstract: In quality control of freeze-dried durian, crispiness is
a key quality index of the product. Generally, crispy testing has to be
done by a destructive method. A nondestructive testing of the
crispiness is required because the samples can be reused for other
kinds of testing. This paper proposed a crispiness classification
method of freeze-dried durians using fuzzy logic for decision
making. The physical changes of a freeze-dried durian include the
pores appearing in the images. Three physical features including (1)
the diameters of pores, (2) the ratio of the pore area and the
remaining area, and (3) the distribution of the pores are considered to
contribute to the crispiness. The fuzzy logic is applied for making the
decision. The experimental results comparing with food expert
opinion showed that the accuracy of the proposed classification
method is 83.33 percent.
Abstract: Data mining is the process of sifting through large
volumes of data, analyzing data from different perspectives and
summarizing it into useful information. One of the widely used
desktop applications for data mining is the Weka tool which is
nothing but a collection of machine learning algorithms implemented
in Java and open sourced under the General Public License (GPL). A
web service is a software system designed to support interoperable
machine to machine interaction over a network using SOAP
messages. Unlike a desktop application, a web service is easy to
upgrade, deliver and access and does not occupy any memory on the
system. Keeping in mind the advantages of a web service over a
desktop application, in this paper we are demonstrating how this Java
based desktop data mining application can be implemented as a web
service to support data mining across the internet.
Abstract: This study was conducted Ismailoglu grape type (Vitis
vinifera L.) and its vine which was aged 15 was grown on its own
root in a vegetation period of 2013 in Nevşehir province in Turkey.
In this research, it was investigated whether the applications of
Control (C), 1/3 cluster tip reduction (1/3 CTR), shoot tip reduction
(STR), 1/3 CTR + STR, TKI-HUMAS (TKI-HM) (Soil) (S), TKIHM
(Foliar) (F), TKI-HM (S + F), 1/3 CTR + TKI-HM (S), 1/3 CTR
+ TKI-HM (F), 1/3 CTR + TKI-HM (S+F), STR + TKI-HM (S), STR
+ TKI-HM (F), STR + TKI-HM (S + F), 1/3 CTR + STR+TKI-HM
(S), 1/3 CTR + STR + TKI-HM (F), 1/3 CTR + STR + TKI-HM (S +
F) on yield and yield components of Ismailoglu grape type. The
results were obtained as the highest fresh grape yield (16.15 kg/vine)
with TKI-HM (S), as the highest cluster weight (652.39 g) with 1/3
CTR + STR, as the highest 100 berry weight (419.07 g) with 1/3
CTR + STR + TKI-HM (F), as the highest maturity index (44.06)
with 1/3 CTR, as the highest must yield (810.00 ml) with STR +
TKI-HM (F), as the highest intensity of L* color (42.04) with TKIHM
(S + F), as the highest intensity of a* color (2.60) with 1/3 CTR
+ TKI-HM (S), as the highest intensity of b* color (7.16) with 1/3
CTR + TKI-HM (S) applications. To increase the fresh grape yield of
Ismailoglu grape type can be recommended TKI-HM (S) application.
Abstract: Research on damage of gears and gear pairs using
vibration signals remains very attractive, because vibration signals
from a gear pair are complex in nature and not easy to interpret.
Predicting gear pair defects by analyzing changes in vibration signal
of gears pairs in operation is a very reliable method. Therefore, a
suitable vibration signal processing technique is necessary to extract
defect information generally obscured by the noise from dynamic
factors of other gear pairs.This article presents the value of cepstrum
analysis in vehicle gearbox fault diagnosis. Cepstrum represents the
overall power content of a whole family of harmonics and sidebands
when more than one family of sidebands is present at the same time.
The concept for the measurement and analysis involved in using the
technique are briefly outlined. Cepstrum analysis is used for detection
of an artificial pitting defect in a vehicle gearbox loaded with
different speeds and torques. The test stand is equipped with three
dynamometers; the input dynamometer serves asthe internal
combustion engine, the output dynamometers introduce the load on
the flanges of the output joint shafts. The pitting defect is
manufactured on the tooth side of a gear of the fifth speed on the
secondary shaft. Also, a method for fault diagnosis of gear faults is
presented based on order Cepstrum. The procedure is illustrated with
the experimental vibration data of the vehicle gearbox. The results
show the effectiveness of Cepstrum analysis in detection and
diagnosis of the gear condition.
Abstract: Project managers are the ultimate responsible for the
overall characteristics of a project, i.e. they should deliver the project
on time with minimum cost and with maximum quality. It is vital for
any manager to decide a trade-off between these conflicting
objectives and they will be benefited of any scientific decision
support tool. Our work will try to determine optimal solutions (rather
than a single optimal solution) from which the project manager will
select his desirable choice to run the project. In this paper, the
problem in project scheduling notated as
(1,T|cpm,disc,mu|curve:quality,time,cost) will be studied. The
problem is multi-objective and the purpose is finding the Pareto
optimal front of time, cost and quality of a project
(curve:quality,time,cost), whose activities belong to a start to finish
activity relationship network (cpm) and they can be done in different
possible modes (mu) which are non-continuous or discrete (disc), and
each mode has a different cost, time and quality . The project is
constrained to a non-renewable resource i.e. money (1,T). Because
the problem is NP-Hard, to solve the problem, a meta-heuristic is
developed based on a version of genetic algorithm specially adapted
to solve multi-objective problems namely FastPGA. A sample project
with 30 activities is generated and then solved by the proposed
method.
Abstract: In the Top Right Access point Minimum Length Corridor (TRA-MLC) problem [1], a rectangular boundary partitioned into rectilinear polygons is given and the problem is to find a corridor of least total length and it must include the top right corner of the outer rectangular boundary. A corridor is a tree containing a set of line segments lying along the outer rectangular boundary and/or on the boundary of the rectilinear polygons. The corridor must contain at least one point from the boundaries of the outer rectangle and also the rectilinear polygons. Gutierrez and Gonzalez [1] proved that the MLC problem, along with some of its restricted versions and variants, are NP-complete. In this paper, we give a shorter proof of NP-Completeness of TRA-MLC by findig the reduction in the following way.
Abstract: In this paper, a Biochemical Methane Potential (BMP)
test provides a measure of the energy production potential from codigestion
between the frozen seafood wastewater and the decanter
cake. The experiments were conducted in laboratory-scale. The
suitable ratio of the frozen seafood wastewater and the decanter cake
was observed in the BMP test. The ratio of the co-digestion between
the frozen seafood wastewater and the decanter cake has impacts on
the biogas production and energy production potential. The best
performance for energy production potential using BMP test
observed from the 180 ml of the frozen seafood wastewater and 10 g
of the decanter cake ratio. This ratio provided the maximum methane
production at 0.351 l CH4/g TCODremoval. The removal efficiencies
are 76.18%, 83.55%, 43.16% and 56.76% at TCOD, SCOD, TS and
VS, respectively. The result can be concluded that the decanter cake
can improve the energy production potential of the frozen seafood
wastewater. The energy provides from co-digestion between frozen
seafood wastewater and decanter cake approximately 19x109
MJ/year in Thailand.
Abstract: Negation is useful in the majority of the real world applications. However, its introduction leads to semantic and canonical problems. SEPN nets are well adapted extension of predicate nets for the definition and manipulation of stratified programs. This formalism is characterized by two main contributions. The first concerns the management of the whole class of stratified programs. The second contribution is related to usual operations optimization (maximal stratification, incremental updates ...). We propose, in this paper, useful algorithms for manipulating stratified programs using SEPN. These algorithms were implemented and validated with STRPRO tool.
Abstract: This study was to investigate the performance of
hybrid solvents blended between primary, secondary, or tertiary
amines and piperazine (PZ) for CO2 removal from flue gas in terms
of CO2 absorption capacity and regeneration efficiency at 90 oC.
Alkanolamines used in this work were monoethanolamine (MEA),
diethanolamine (DEA), and triethanolamine (TEA). The CO2
absorption was experimentally examined under atmospheric pressure
and room temperature. The results show that MEA blend with PZ
provided the maximum CO2 absorption capacity of 0.50 mol
CO2/mol amine while TEA provided the minimum CO2 absorption
capacity of 0.30 mol CO2/mol amine. TEA was easier to regenerate
for both first cycle and second cycle with less loss of absorption
capacity. The regeneration efficiency of TEA was 95.09 and 92.89 %,
for the first and second generation cycles, respectively.
Abstract: Superplastic deformation and high temperature load
relaxation behavior of coarse-grained iron aluminides with the
composition of Fe-28 at.% Al have been investigated. A series of load
relaxation and tensile tests were conducted at temperatures ranging
from 600 to 850oC. The flow curves obtained from load relaxation
tests were found to have a sigmoidal shape and to exhibit stress vs.
strain rate data in a very wide strain rate range from 10-7/s to 10-2/s.
Tensile tests have been conducted at various initial strain rates ranging
from 3×10-5/s to 1×10-2/s. Maximum elongation of ~500 % was
obtained at the initial strain rate of 3×10-5/s and the maximum strain
rate sensitivity was found to be 0.68 at 850oC in binary Fe-28Al alloy.
Microstructure observation through the optical microscopy (OM) and
the electron back-scattered diffraction (EBSD) technique has been
carried out on the deformed specimens and it has revealed the
evidences for grain boundary migration and grain refinement to occur
during superplastic deformation, suggesting the dynamic
recrystallization mechanism. The addition of Cr by the amount of 5
at.% appeared to deteriorate the superplasticity of the binary iron
aluminide. By applying the internal variable theory of structural
superplasticity, the addition of Cr has been revealed to lower the
contribution of the frictional resistance to dislocation glide during high
temperature deformation of the Fe3Al alloy.
Abstract: Researches related to standard product model and
development of neutral manufacturing interfaces for numerical
control machines becomes a significant topic since the last 25 years.
In this paper, a detail description of STEP implementation on turnmill
manufacturing has been discussed. It shows requirements of
information contents from ISO14649 data model. It covers to
describe the design of STEP-NC framework applicable to turn-mill
manufacturing. In the framework, EXPRESS-G and UML modeling
tools are used to depict the information contents of the system and
established the bases of information model requirement. A product
and manufacturing data model applicable for STEP compliant
manufacturing. The next generation turn-mill operations
requirements have been represented by a UML diagram. An object
oriented classes of ISO1449 has been developed on Visual Basic dot
NET platform for binding the static information model represented
by the UML diagram. An architect of the proposed system
implementation has been given on the bases of the design and
manufacturing module of STEP-NC interface established. Finally, a
part 21 file process plan generated for an illustration of turn-mill
components.
Abstract: The study was designed to develop a measurement of
the positive emotion regulation questionnaire (PERQ) that assesses
positive emotion regulation strategies through self-report. The 14
items developed for the surveying instrument of the study were based
upon literatures regarding elements of positive regulation strategies.
319 elementary students (age ranging from 12 to14) were recruited
among three public elementary schools to survey on their use of
positive emotion regulation strategies. Of 319 subjects, 20 invalid
questionnaire s yielded a response rate of 92%. The data collected
wasanalyzed through methods such as item analysis, factor analysis,
and structural equation models. In reference to the results from item
analysis, the formal survey instrument was reduced to 11 items. A
principal axis factor analysis with varimax was performed on
responses, resulting in a 2-factor equation (savoring strategy and
neutralizing strategy), which accounted for 55.5% of the total
variance. Then, the two-factor structure of scale was also identified by
structural equation models. Finally, the reliability coefficients of the
two factors were Cronbach-s α .92 and .74. Gender difference was
only found in savoring strategy. In conclusion, the positive emotion
regulation strategies questionnaire offers a brief, internally consistent,
and valid self-report measure for understanding the emotional
regulation strategies of children that may be useful to researchers and
applied professionals.