Abstract: In this paper, mathematical models for permutation flow shop scheduling and job shop scheduling problems are proposed. The first problem is based on a mixed integer programming model. As the problem is NP-complete, this model can only be used for smaller instances where an optimal solution can be computed. For large instances, another model is proposed which is suitable for solving the problem by stochastic heuristic methods. For the job shop scheduling problem, a mathematical model and its main representation schemes are presented.
Abstract: The present study deals with the modeling and simulation of flow through an annular reactor at different hydrodynamic conditions using computational fluid dynamics (CFD) to investigate the flow behavior. CFD modeling was utilized to predict velocity distribution and average velocity in the annular geometry. The results of CFD simulations were compared with the mathematically derived equations and already developed correlations for validation purposes. CFD modeling was found suitable for predicting the flow characteristics in annular geometry under laminar flow conditions. It was observed that CFD also provides local values of the parameters of interest in addition to the average values for the simulated geometry.
Abstract: The aim of this research is to develop a fast and
reliable surveillance system based on a personal digital assistant
(PDA) device. This is to extend the capability of the device to detect
moving objects which is already available in personal computers.
Secondly, to compare the performance between Background
subtraction (BS) and Temporal Frame Differencing (TFD) techniques
for PDA platform as to which is more suitable. In order to reduce
noise and to prepare frames for the moving object detection part,
each frame is first converted to a gray-scale representation and then
smoothed using a Gaussian low pass filter. Two moving object
detection schemes i.e., BS and TFD have been analyzed. The
background frame is updated by using Infinite Impulse Response
(IIR) filter so that the background frame is adapted to the varying
illuminate conditions and geometry settings. In order to reduce the
effect of noise pixels resulting from frame differencing
morphological filters erosion and dilation are applied. In this
research, it has been found that TFD technique is more suitable for
motion detection purpose than the BS in term of speed. On average
TFD is approximately 170 ms faster than the BS technique
Abstract: Building life cycle will never be excused from the existence of defects and deterioration. They are common problems in building, existed in newly build or in aged building. Buildings constructed from wood are indeed affected by its agent and serious defects and damages can reduce values to a building. In repair works, it is important to identify the causes and repair techniques that best suites with the condition. This paper reviews the conservation of traditional timber mosque in Malaysia comprises the concept, principles and approaches of mosque conservation in general. As in conservation practice, wood in historic building can be conserved by using various restoration and conservation techniques which this can be grouped as Fully and Partial Replacement, Mechanical Reinforcement, Consolidation by Impregnation and Reinforcement, Removing Paint and also Preservation of Wood and Control Insect Invasion, as to prolong and extended the function of a timber in a building. It resulted that the common techniques adopted in timber mosque conservation are from the conventional ways and the understanding of the repair technique requires the use of only preserve wood to prevent the future immature defects.
Abstract: With the aim of improving nutritional profile and antioxidant capacity of gluten-free cookies, blueberry pomace, by-product of juice production, was processed into a new food ingredient by drying and grinding and used for a gluten-free cookie formulation. Since the quality of a baked product is highly influenced by the baking conditions, the objective of this work was to optimize the baking time and thickness of dough pieces, by applying Response Surface Methodology (RSM) in order to obtain the best technological quality of the cookies. The experiments were carried out according to a Central Composite Design (CCD) by selecting the dough thickness and baking time as independent variables, while hardness, color parameters (L*, a* and b* values), water activity, diameter and short/long ratio were response variables. According to the results of RSM analysis, the baking time of 13.74min and dough thickness of 4.08mm was found to be the optimal for the baking temperature of 170°C. As similar optimal parameters were obtained by previously conducted experiment based on sensory analysis, response surface methodology (RSM) can be considered as a suitable approach to optimize the baking process.
Abstract: This paper focuses on operational risk measurement
techniques and on economic capital estimation methods. A data
sample of operational losses provided by an anonymous Central
European bank is analyzed using several approaches. Loss
Distribution Approach and scenario analysis method are considered.
Custom plausible loss events defined in a particular scenario are
merged with the original data sample and their impact on capital
estimates and on the financial institution is evaluated. Two main
questions are assessed – What is the most appropriate statistical
method to measure and model operational loss data distribution? and
What is the impact of hypothetical plausible events on the financial
institution? The g&h distribution was evaluated to be the most
suitable one for operational risk modeling. The method based on the
combination of historical loss events modeling and scenario analysis
provides reasonable capital estimates and allows for the measurement
of the impact of extreme events on banking operations.
Abstract: To understand life as biological system, evolutionary
understanding is indispensable. Protein interactions data are rapidly
accumulating and are suitable for system-level evolutionary analysis.
We have analyzed yeast protein interaction network by both
mathematical and biological approaches. In this poster presentation,
we inferred the evolutionary birth periods of yeast proteins by
reconstructing phylogenetic profile. It has been thought that hub
proteins that have high connection degree are evolutionary old. But
our analysis showed that hub proteins are entirely evolutionary new.
We also examined evolutionary processes of protein complexes. It
showed that member proteins of complexes were tend to have
appeared in the same evolutionary period. Our results suggested that
protein interaction network evolved by modules that form the
functional unit. We also reconstructed standardized phylogenetic trees
and calculated evolutionary rates of yeast proteins. It showed that
there is no obvious correlation between evolutionary rates and
connection degrees of yeast proteins.
Abstract: We present a visualization technique for radial drawing of trees consisting of two slightly different algorithms. Both of them make use of node-link diagrams for visual encoding. This visualization creates clear drawings without edge crossing. One of the algorithms is suitable for real-time visualization of large trees, as it requires minimal recalculation of the layout if leaves are inserted or removed from the tree; while the other algorithm makes better utilization of the drawing space. The algorithms are very similar and follow almost the same procedure but with different parameters. Both algorithms assign angular coordinates for all nodes which are then converted into 2D Cartesian coordinates for visualization. We present both algorithms and discuss how they compare to each other.
Abstract: The object of this work is the probabilistic performance evaluation of safety instrumented systems (SIS), i.e. the average probability of dangerous failure on demand (PFDavg) and the average frequency of failure (PFH), taking into account the uncertainties related to the different parameters that come into play: failure rate (λ), common cause failure proportion (β), diagnostic coverage (DC)... This leads to an accurate and safe assessment of the safety integrity level (SIL) inherent to the safety function performed by such systems. This aim is in keeping with the requirement of the IEC 61508 standard with respect to handling uncertainty. To do this, we propose an approach that combines (1) Monte Carlo simulation and (2) fuzzy sets. Indeed, the first method is appropriate where representative statistical data are available (using pdf of the relating parameters), while the latter applies in the case characterized by vague and subjective information (using membership function). The proposed approach is fully supported with a suitable computer code.
Abstract: One of the important applications of gas turbines is
their utilization for heat recovery steam generator in combine-cycle technology. Exhaust flow and energy are two key parameters for
determining heat recovery steam generator performance which are mainly determined by the main gas turbine components performance
data. For this reason a method was developed for determining the
exhaust energy in the new edition of ASME PTC22. The result of this investigation shows that the method of standard has considerable
error. Therefore in this paper a new method is presented for modifying of the performance calculation. The modified method is
based on exhaust gas constituent analysis and combustion calculations. The case study presented here by two kind of General
Electric gas turbine design data for validation of methodologies. The
result shows that the modified method is more precise than the ASME PTC22 method. The exhaust flow calculation deviation from
design data is 1.5-2 % by ASME PTC22 method so that the deviation regarding with modified method is 0.3-0.5%. Based on precision of
analyzer instruments, the method can be suitable alternative for gas
turbine standard performance test. In advance two methods are
proposed based on known and unknown fuel in modified method procedure. The result of this paper shows that the difference between
the two methods is below than %0.02. In according to reasonable esult of the second procedure (unknown fuel composition), the
method can be applied to performance evaluation of gas turbine, so that the measuring cost and data gathering should be reduced.
Abstract: During the last decade Panicum virgatum, known as
Switchgrass, has been broadly studied because of its remarkable
attributes as a substitute pasture and as a functional biofuel source.
The objective of this investigation was to establish soil suitability for
Switchgrass in the State of Mississippi. A linear weighted additive
model was developed to forecast soil suitability. Multicriteria
analysis and Sensitivity analysis were utilized to adjust and optimize
the model. The model was fit using seven years of field data
associated with soils characteristics collected from Natural Resources
Conservation System - United States Department of Agriculture
(NRCS-USDA). The best model was selected by correlating
calculated biomass yield with each model's soils-based output for
Switchgrass suitability. Coefficient of determination (r2) was the
decisive factor used to establish the 'best' soil suitability model.
Coefficients associated with the 'best' model were implemented
within a Geographic Information System (GIS) to create a map of
relative soil suitability for Switchgrass in Mississippi. A Geodatabase
associated with soil parameters was built and is available for future
Geographic Information System use.
Abstract: Starting from the basic pillars of the supportability
analysis this paper queries its characteristics in LCI (Life Cycle
Integration) environment. The research methodology contents a
review of modern logistics engineering literature with the objective to
collect and synthesize the knowledge relating to standards of
supportability design in e-logistics environment. The results show
that LCI framework has properties which are in fully compatibility
with the requirement of simultaneous logistics support and productservice
bundle design. The proposed approach is a contribution to the
more comprehensive and efficient supportability design process.
Also, contributions are reflected through a greater consistency of
collected data, automated creation of reports suitable for different
analysis, as well as the possibility of their customization according
with customer needs. In addition to this, convenience of this approach
is its practical use in real time. In a broader sense, LCI allows
integration of enterprises on a worldwide basis facilitating electronic
business.
Abstract: This research proposes the change of damping coefficient regarding minimum displacement. From the mass with external forced and damper problem, when is the constant external forced transmitted to the understructure in the difference angle between 30 and 60 degrees. This force generates the vibration as general known; however, the objective of this problem is to have minimum displacement. As the angle is changed and the goal is the same; therefore, the damper of the system must be varied while keeping constant spring stiffness. The problem is solved by using nonlinear programming and the suitable changing of the damping coefficient is provided.
Abstract: Recognizing human action from videos is an active
field of research in computer vision and pattern recognition. Human
activity recognition has many potential applications such as video
surveillance, human machine interaction, sport videos retrieval and
robot navigation. Actually, local descriptors and bag of visuals words
models achieve state-of-the-art performance for human action
recognition. The main challenge in features description is how to
represent efficiently the local motion information. Most of the
previous works focus on the extension of 2D local descriptors on 3D
ones to describe local information around every interest point. In this
paper, we propose a new spatio-temporal descriptor based on a spacetime
description of moving points. Our description is focused on an
Accordion representation of video which is well-suited to recognize
human action from 2D local descriptors without the need to 3D
extensions. We use the bag of words approach to represent videos.
We quantify 2D local descriptor describing both temporal and spatial
features with a good compromise between computational complexity
and action recognition rates. We have reached impressive results on
publicly available action data set
Abstract: Tehran, one of the heavily-populated capitals, is
severely suffering from increasing air pollution. To show a
documented trend of such pollutants during last years, plane tree
species (Platanus orientalis) were suited to be studied as indicators,
for the species have been planted throughout the city many years
ago. Two areas (Saadatabad and Narmak districts) allotting different
contents of crowed and highly-traffic routs but the same ecological
characteristics were selected. Twelve sample individuals were cored
twice perpendicularly in each area. Tree-rings of each core were
measured by a binocular microscope and separated annually for the
last 25 years. Two heavy metals including Cd and Pb accompanied
by a mineral element (Ca) were analyzed using Hatch method. Treerings
analysis of the two areas showed different groups in term of
physiologically ability as the growths were plunged during the last
10 years in Saadatabad district and showed a slight decrease in the
same period for another studying area. In direct contrast to
decreasing growth trend in Saadatabad, all three mentioned elements
increased sharply during last 25 years in the same area. When it came
to Narmak district, the trend was completely different with
Saadatabad. There were some fluctuations in absorbing trace
elements like tree-rings widths were, yet calcium showed an upward
trend all the last 25 years. The results of the study proved the
possibility of using tree species of each region to monitor its air
pollution trends of the past, hence to depict a pollution assessment of
a populated city for last years and then to make appropriate decisions
for the future as it is well-known what the trend is. On the other
hand, risen values of calcium (as the stress-indicator element)
accompanied by increased trace elements suggests non-sustainable
state of the trees.
Abstract: Geosynthetics have proved to be suitable for
reinforced soil retaining walls. Based on the increasing uses of
geosynthetic reinforced soil systems in the regions, which bear
frequent earthquakes, the study of dynamic behavior of structures
seems necessary. Determining the reinforcement forces is; therefore,
one of the most important and main points of discussions in
designing retaining walls, by which we prevent from conservative
planning. Thus, this paper intended to investigate the effects of such
parameters as wall height, acceleration type, vertical spacing of
reinforcement, type of reinforcement and soil type on forces and
deformation through numerical modeling of the geosynthetic
reinforced soil retaining walls (GRSRW) under dynamic loading with
finite difference method by using FLAC. The findings indicate rather
positive results with each parameter.
Abstract: Based on the combined shape feature and texture
feature, a fast object detection method with rotation invariant features
is proposed in this paper. A quick template matching scheme based
online learning designed for online applications is also introduced in
this paper. The experimental results have shown that the proposed
approach has the features of lower computation complexity and
higher detection rate, while keeping almost the same performance
compared to the HOG-based method, and can be more suitable for
run time applications.
Abstract: Many commercial processes are available for the
removal of H2S from gaseous streams. The desulfurization of gas
streams using aqueous ferric sulfate solution as washing liquor is
studied. Apart from sulfur, only H2O is generated in the process, and
consequently, no waste treatment facilities are required. A distinct
advantage of the process is that the reaction of H2S with is so rapid
and complete that there remains no danger of discharging toxic waste
gas. In this study, the reactive absorption of hydrogen sulfide into
aqueous ferric sulfate solution has been studied and design
calculations for equipments have been done and effective operation
parameters on this process considered. Results show that high
temperature and low pressure are suitable for absorption reaction.
Variation of hydrogen sulfide concentration and Fe3+ concentration
with time in absorption reaction shown that the reaction of ferric
sulfate and hydrogen sulfide is first order with respect to the both
reactant. At low Fe2(SO4)3 concentration the absorption rate of H2S
increase with increasing the Fe2(SO4)3 concentration. At higher
concentration a decrease in the absorption rate was found. At higher
concentration of Fe2(SO4)3, the ionic strength and viscosity of
solution increase remarkably resulting in a decrease of solubility,
diffusivity and hence absorption rate.
Abstract: This study mainly aims at assessing the level of
microbial pollution of the water used in the chair system in dental
clinics. For this purpose 36 samples have been randomly collected
from a number of dental surgeries in the city of Tripoli in Libya.
However, 32 of the samples have tested positive to microbial
pollution including 13 of the samples, which have tested positives to
Pseudomonas aeruginosa. Based on the results of the test a further
investigation of the biofilms incorporated within the dental chair
system has been conducted. The laboratory tests of biofilms with
similar design to those found in dental chairs have proved that
bacterial pollution takes place through saliva of the patients who use
the chairs, and that this saliva is rich with nutrients which provides a
suitable breeding ground for all types of bacteria.
Abstract: Industrial robots become useless without end-effectors
that for many instances are in the form of friction grippers.
Commonly friction grippers apply frictional forces to different
objects on the basis of programmers- experiences. This puts a
limitation on the effectiveness of gripping force that may result in
damaging the object. This paper describes various stages of design
and development of a low cost sensor-based robotic gripper that
would facilitate the task of applying right gripping forces to different
objects. The gripper is also equipped with range sensors in order to
avoid collisions of the gripper with objects. It is a fully functional
automated pick and place gripper which can be used in many
industrial applications. Yet it can also be altered or further developed
in order to suit a larger number of industrial activities. The current
design of gripper could lead to designing completely automated robot
grippers able to improve the efficiency and productivity of industrial
robots.