Abstract: This paper introduces the effective speckle reduction of
synthetic aperture radar (SAR) images using inner product spaces in
undecimated wavelet domain. There are two major areas in projection
onto span algorithm where improvement can be made. First is the use
of undecimated wavelet transformation instead of discrete wavelet
transformation. And second area is the use of smoothing filter namely
directional smoothing filter which is an additional step. Proposed
method does not need any noise estimation and thresholding
technique. More over proposed method gives good results on both
single polarimetric and fully polarimetric SAR images.
Abstract: Internal combustion engines rejects 30-40% of the
energy supplied by fuel to the environment through exhaust gas. thus, there is a possibility for further significant improvement of efficiency with the utilization of exhaust gas energy and its conversion to mechanical energy or electrical energy. The Thermo-Electric
Generator (TEG) will be located in the exhaust system and will make use of an energy flow between the warmer exhaust gas and the external environment. Predict to th optimum position of temperature
distribution and the performance of TEG through numerical analysis.
The experimental results obtained show that the power output significantly increases with the temperature difference between cold
and hot sides of a thermoelectric generator.
Abstract: The steady state response of bond graphs representing
passive and active suspension is presented. A bond graph with
preferred derivative causality assignment to get the steady state
is proposed. A general junction structure of this bond graph
is proposed. The proposed methodology to passive and active
suspensions is applied.
Abstract: Crawling movement as a motive mode seen in nature
of some animals such as snakes possesses a specific syntactic and
dynamic analysis. Serpentine robot designed by inspiration from
nature and snake-s crawling motion, is regarded as a crawling robot.
In this paper, a serpentine robot with spiral motion model will be
analyzed. The purpose of this analysis is to calculate the vertical and
tangential forces along snake-s body and to determine the parameters
affecting on these forces. Two types of serpentine robots have been
designed in order to examine the achieved relations explained below.
Abstract: An experimental study of Reinforced Concrete, RC, columns strengthened using a steel jacketing technique was conducted. The jacketing technique consisted of four steel vertical angles installed at the corners of the column joined by horizontal steel straps confining the column externally. The effectiveness of the technique was evaluated by testing the RC column specimens under eccentric monotonic loading until failure occurred. Strain gauges were installed to monitor the strains in the internal reinforcement as well as the external jacketing system. The effectiveness of the jacketing technique was demonstrated, and the parameters affecting the technique were studied.
Abstract: Although the STL (stereo lithography) file format is
widely used as a de facto industry standard in the rapid prototyping
industry due to its simplicity and ability to tessellation of almost all
surfaces, but there are always some defects and shortcoming in their
usage, which many of them are difficult to correct manually. In
processing the complex models, size of the file and its defects grow
extremely, therefore, correcting STL files become difficult. In this
paper through optimizing the exiting algorithms, size of the files and
memory usage of computers to process them will be reduced. In spite
of type and extent of the errors in STL files, the tail-to-head
searching method and analysis of the nearest distance between tails
and heads techniques were used. As a result STL models sliced
rapidly, and fully closed contours produced effectively and errorless.
Abstract: In this paper, solution of fuzzy differential equation
under general differentiability is obtained by simulink. The simulink
solution is equivalent or very close to the exact solution of the
problem. Accuracy of the simulink solution to this problem is
qualitatively better. An illustrative numerical example is presented
for the proposed method.
Abstract: In industrial scale of Gas to Liquid (GTL) process in
Fischer-Tropsch (FT) synthesis, a part of reactor outlet gases such as
CO2 and CH4 as side reaction products, is usually recycled. In this
study, the influence of CO2 and CH4 on the performance and
selectivity of Co-Ru/Al2O3 catalyst is investigated by injection of
these gases (0-20 vol. % of feed) to the feed stream. The effect of
temperature and feed flow rate, are also inspected. The results show
that low amounts of CO2 in the feed stream, doesn`t change the
catalyst activity significantly but increasing the amount of CO2 (more
than 10 vol. %) cause the CO conversion to decrease and the
selectivity of heavy components to increase. Methane acts as an inert
gas and doesn`t affect the catalyst performance. Increasing feed flow
rate has negative effect on both CO conversion and heavy component
selectivity. By raising the temperature, CO conversion will increase
but there are more volatile components in the product. The effect of
CO2 on the catalyst deactivation is also investigated carefully and a
mechanism is suggested to explain the negative influence of CO2 on
catalyst deactivation.
Abstract: This work aims to explore the factors that have an incidence in reading comprehension process, with different type of texts. In a recent study with 2nd, 3rd and 4th grade children, it was observed that reading comprehension of narrative texts was better than comprehension of expository texts. Nevertheless it seems that not only the type of text but also other textual factors would account for comprehension depending on the cognitive processing demands posed by the text. In order to explore this assumption, three narrative and three expository texts were elaborated with different degree of complexity. A group of 40 fourth grade Spanish-speaking children took part in the study. Children were asked to read the texts and answer orally three literal and three inferential questions for each text. The quantitative and qualitative analysis of children responses showed that children had difficulties in both, narrative and expository texts. The problem was to answer those questions that involved establishing complex relationships among information units that were present in the text or that should be activated from children’s previous knowledge to make an inference. Considering the data analysis, it could be concluded that there is some interaction between the type of text and the cognitive processing load of a specific text.
Abstract: Using a set of confidence intervals, we develop a
common approach, to construct a fuzzy set as an estimator for
unknown parameters in statistical models. We investigate a method
to derive the explicit and unique membership function of such fuzzy
estimators. The proposed method has been used to derive the fuzzy
estimators of the parameters of a Normal distribution and some
functions of parameters of two Normal distributions, as well as the
parameters of the Exponential and Poisson distributions.
Abstract: Aquatic and semi aquatic birds as a group are suited to
feed and breed in environments in which water forms a fundamental
part. These birds are biological indicator in aquatic environment,
because these birds belong to the top level of food chain in aquatic
ecosystems. There are 61 species in 14 families of aquatic and semi
aquatic birds in Iran. The birds of the Sattarkhan Lake belong to 16
species in 8 families which include 26.2 percent of total Aquatic and
semi aquatic bird species and 57% of Aquatic and semi aquatic bird's
family of Iran. Study was carried out monthly at Sattarkhan Lake
show the existence of Phalacrocorax carbo, Ardea cinerea, Egretta
alba, Egretta garzetta, Bubulcus ibis, Botaurus stellaris, Sterna
hirundo, Chlidonias leucopterus, Larus minutus, Larus argentatus,
Larus ridibunbus, Alcedo atthis, Ciconia ciconia, Plegadis
falcinellus, Circus aeruginosus, Corvus frugilegus
Abstract: Nowadays, consumption of whole flours and flours
with high extraction rate is recommended, because of their high
amount of fibers, vitamins and minerals. Despite nutritional benefits
of whole flour, concentration of some undesirable components such
as phytic acid is higher than white flour. In this study, effect of
several lactic acid bacteria sourdough on Toast bread is investigated.
Sourdough from lactic acid bacteria (Lb. plantarum, Lb. reuteri) with
different dough yield (250 and 300) is made and incubated at 30°C
for 20 hour, then added to dough in the ratio of 10, 20 and 30%
replacement. Breads that supplemented with Lb. plantarum
sourdough had lower phytic acid. Higher replacement of sourdough
and higher DY cause higher decrease in phytic acid content.
Sourdough from Lb. plantarum, DY = 300 and 30% replacement
cause the highest decrease in phytic acid content (49.63 mg/100g).
As indicated by panelists, Lb. reuteri sourdough can present the
greatest effect on overall quality score of the breads. DY reduction
cause a decrease in bread quality score. Sensory score of Toast bread
is 81.71 in the samples that treated with Lb. reuteri sourdough with
DY = 250 and 20% replacement.
Abstract: The hybridization of artificial immune system with
cellular automata (CA-AIS) is a novel method. In this hybrid model,
the cellular automaton within each cell deploys the artificial immune
system algorithm under optimization context in order to increase its
fitness by using its neighbor-s efforts. The hybrid model CA-AIS is
introduced to fix the standard artificial immune system-s weaknesses.
The credibility of the proposed approach is evaluated by simulations
and it shows that the proposed approach achieves better results
compared to standard artificial immune system.
Abstract: A total of twenty tensile biopsies were collected from
children undergoing tonsillectomy from teaching hospital ENT
department and Kurdistan private hospital in sulaimani city. All
biopsies were homogenized and cultured; the obtained bacterial
isolates were purified and identified by biochemical tests and VITEK
2 compact system. Among the twenty studied samples, only one
Pseudomonas putida with probability of 99% was isolated.
Antimicrobial susceptibility was carried out by disk diffusion
method, Pseudomonas putida showed resistance to all antibiotics
used except vancomycin. The isolate further subjected to PCR and
DNA sequence analysis of blaVIM gene using different set of primers
for different regions of VIM gene. The results were found to be PCR
positive for the blaVIM gene. To determine the sequence of blaVIM
gene, DNA sequencing performed. Sequence alignment of blaVIM
gene with previously recorded blaVIM gene in NCBI- database showed
that P. putida isolate have different blaVIM gene.
Abstract: In this paper, a method to detect multiple ellipses is presented. The technique is efficient and robust against incomplete ellipses due to partial occlusion, noise or missing edges and outliers. It is an iterative technique that finds and removes the best ellipse until no reasonable ellipse is found. At each run, the best ellipse is extracted from randomly selected edge patches, its fitness calculated and compared to a fitness threshold. RANSAC algorithm is applied as a sampling process together with the Direct Least Square fitting of ellipses (DLS) as the fitting algorithm. In our experiment, the method performs very well and is robust against noise and spurious edges on both synthetic and real-world image data.
Abstract: The efficient knowledge management system (KMS)
is one of the important strategies to help firms to achieve sustainable
competitive advantages, but little research has been conducted to
understand what contributes to the KMS success. This study thus set
to investigate the determinants of KMS success in the context of Thai
banking industry. A questionnaire survey was conducted in four
major Thai Banks to test the proposed KMS Success model.
The result of this study shows that KMS use and user satisfaction
relate significantly to the success of KMS, and knowledge quality,
service quality and trust lead to system use, and knowledge quality,
system quality and trust lead to user satisfaction. However, this
research focuses only on system and user-related factors. Future
research thus can extend to study factors such as management support
and organization readiness.
Abstract: The growing outsourcing of logistics services
resulting from the ongoing current in firms of costs
reduction/increased efficiency means that it is becoming more and
more important for the companies doing the outsourcing to carry out
a proper evaluation.
The multiple definitions and measures of logistics service
performance found in research on the topic create a certain degree of
confusion and do not clear the way towards the proper measurement
of their performance. Do a model and a specific set of indicators exist
that can be considered appropriate for measuring the performance of
logistics services outsourcing in industrial environments? Are said
indicators in keeping with the objectives pursued by outsourcing? We
aim to answer these and other research questions in the study we have
initiated in the field within the framework of the international High
Performance Manufacturing (HPM) project of which this paper
forms part.
As the first stage of this research, this paper reviews articles
dealing with the topic published in the last 15 years with the aim of
detecting the models most used to make this measurement and
determining which performance indicators are proposed as part of
said models and which are most used. The first steps are also taken in
determining whether these indicators, financial and operational, cover
the aims that are being pursued when outsourcing logistics services.
The findings show there is a wide variety of both models and
indicators used. This would seem to testify to the need to continue
with our research in order to try to propose a model and a set of
indicators for measuring the performance of logistics services
outsourcing in industrial environments.
Abstract: This paper describes a 3D modeling system in
Augmented Reality environment, named 3DARModeler. It can be
considered a simple version of 3D Studio Max with necessary
functions for a modeling system such as creating objects, applying
texture, adding animation, estimating real light sources and casting
shadows. The 3DARModeler introduces convenient, and effective
human-computer interaction to build 3D models by combining both
the traditional input method (mouse/keyboard) and the tangible input
method (markers). It has the ability to align a new virtual object with
the existing parts of a model. The 3DARModeler targets nontechnical
users. As such, they do not need much knowledge of
computer graphics and modeling techniques. All they have to do is
select basic objects, customize their attributes, and put them together
to build a 3D model in a simple and intuitive way as if they were
doing in the real world. Using the hierarchical modeling technique,
the users are able to group several basic objects to manage them as a
unified, complex object. The system can also connect with other 3D
systems by importing and exporting VRML/3Ds Max files. A
module of speech recognition is included in the system to provide
flexible user interfaces.
Abstract: Recent financial international scandals around the world have led to a number of investigations into the effectiveness of corporate governance practices and audit quality. Although evidence of corporate governance practices and audit quality exists from developed economies, very scanty studies have been conducted in Egypt where corporate governance is just evolving. Therefore, this study provides evidence on the effectiveness of corporate governance practices and audit quality from a developing country. The data for analysis are gathered from the top 50 most active companies in the Egyptian Stock Exchange, covering the three year period 2007-2009. Logistic regression was used in investigating the questions that were raised in the study. Findings from the study show that board independence; CEO duality and audit committees significantly have relationship with audit quality. The results also, indicate that institutional investor and managerial ownership have no significantly relationship with audit quality. Evidence also exist that size of the company; complexity and business leverage are important factors in audit quality for companies quoted on the Egypt Stock Exchange.
Abstract: Scale defects are common surface defects in hot steel rolling. The modelling of such defects is problematic and their causes are not straightforward. In this study, we investigated genetic algorithms in search for a mathematical solution to scale formation. For this research, a high-dimensional data set from hot steel rolling process was gathered. The synchronisation of the variables as well as the allocation of the measurements made on the steel strip were solved before the modelling phase.