Abstract: This paper presents the voltage regulation scheme of
D-STATCOM under three-phase faults. It consists of the voltage
detection and voltage regulation schemes in the 0dq reference. The
proposed control strategy uses the proportional controller in which
the proportional gain, kp, is appropriately adjusted by using genetic
algorithms. To verify its use, a simplified 4-bus test system is situated
by assuming a three-phase fault at bus 4. As a result, the DSTATCOM
can resume the load voltage to the desired level within
1.8 ms. This confirms that the proposed voltage regulation scheme
performs well under three-phase fault events.
Abstract: The significance of environmental protection is wellknown in today's world. The execution of any program depends on sufficient knowledge and required familiarity with environment and its pollutants. Taking advantage of a systematic method, as a new science, in environmental planning can solve many problems. In this article, air pollution in Tehran and its relationship with health and population growth have been analyzed using dynamic systems. Firstly, by using casual loops, the relationship between the parameters effective on air pollution in Tehran were taken into consideration, then these casual loops were turned into flow diagrams [6], and finally, they were simulated using the software Vensim [16]in order to conclude what the effect of each parameter will be on air pollution in Tehran in the next 10 years, how changing of one or more parameters influences other parameters, and which parameter among all other parameters requires to be controlled more.
Abstract: Yogyakarta, as the capital city of Yogyakarta Province, has important roles in various sectors that require good provision of public transportation system. Ideally, a good transportation system should be able to accommodate the amount of travel demand. This research attempts to develop a trip generation model to predict the number of public transport passenger in Yogyakarta city. The model is built by using multiple linear regression analysis, which establishes relationship between trip number and socioeconomic attributes. The data consist of primary and secondary data. Primary data was collected by conducting household surveys which randomly selected. The resulted model is further applied to evaluate the existing TransJogja, a new Bus Rapid Transit system serves Yogyakarta and surrounding cities, shelters.
Abstract: To enhance installation security, a LNG storage in Rudong of Jiangsu province was adopted as a practical work, and it was analyzed by nonlinear finite element method to research overall and local stability performance, as well as the stress and deformation under the action of wind load and self-weight. Results indicate that deformation is tiny when steel mesh maintains as an overall ring, and stress caused by vertical bending moment and tension of bottom tie wire are also in the safe range. However, axial forces of lap reinforcement in adjacent steel mesh exceed the ultimate bearing capacity of tie wire. Hence, tie wires are ruptured; single mesh loses lateral connection and turns into monolithic status as the destruction of overall structure. Further more, monolithic steel mesh is led to collapse by the damage of bottom connection. So, in order to prevent connection failure and enhance installation security, the overlapping parts of steel mesh should be taken more reliable measures.
Abstract: This study aims to assess the potential of solar energy technology for improving access to water and hence the livelihood strategies of rural communities in Baja California Sur, Mexico. It focuses on livestock ranches and photovoltaic water-pumptechnology as well as other water extraction methods. The methodology used are the Sustainable Livelihoods and the Appropriate Technology approaches. A household survey was applied in June of 2006 to 32 ranches in the municipality, of which 22 used PV pumps; and semi-structured interviews were conducted. Findings indicate that solar pumps have in fact helped people improve their quality of life by allowing them to pursue a different livelihood strategy and that improved access to water -not necessarily as more water but as less effort to extract and collect it- does not automatically imply overexploitation of the resource; consumption is based on basic needs as well as on storage and pumping capacity. Justification for such systems lies in the avoidance of logistical problems associated to fossil fuels, PV pumps proved to be the most beneficial when substituting gasoline or diesel equipment but of dubious advantage if intended to replace wind or gravity systems. Solar water pumping technology-s main obstacle to dissemination are high investment and repairs costs and it is therefore not suitable for all cases even when insolation rates and water availability are adequate. In cases where affordability is not an obstacle it has become an important asset that contributes –by means of reduced expenses, less effort and saved time- to the improvement of livestock, the main livelihood provider for these ranches.
Abstract: Optimization of a microwave-assisted extraction of cherry laurel (Prunus laurocerasus) fruit using methanol was studied. The influence of process parameters (microwave power, plant material-to-solvent ratio and the extraction time) on the extraction efficiency were optimized by using response surface methodology. The predicted maximum yield of extractive substances (41.85 g/100 g fresh plant material) was obtained at microwave power of 600 W and plant material to solvent ratio of 0.2 g/cm3 after 26 minutes of extraction, while a mean value of 40.80±0.41 g/100 g fresh plant material was obtained from laboratory experiments. This proves applicability of the model in predicting optimal extraction conditions with minimal laborious and time consuming. The results indicated that all process parameters were effective on the extraction efficiency, while the most important factor was extraction time. In order to rationalize production the optimal economical condition which gave a large total extract yield with minimal energy and solvent consumption was found.
Abstract: In all industries which are related to heat, suitable
thermal ranges are defined for each device to operate well.
Consideration of these limits requires a thermal control unit beside
the main system. The Satellite Thermal Control Unit exploits from
different methods and facilities individually or mixed. For enhancing
heat transfer between primary surface and the environment,
utilization of radiating extended surfaces are common. Especially for
large temperature differences; variable thermal conductivity has a
strong effect on performance of such a surface .In most literatures,
thermo-physical properties, such as thermal conductivity, are
assumed as constant. However, in some recent researches the
variation of these parameters is considered. This may be helpful for
the evaluation of fin-s temperature distribution in relatively large
temperature differences. A new method is introduced to evaluate
temperature-dependent thermal conductivity values. The finite
volume method is employed to simulate numerically the temperature
distribution in a space radiating fin. The present modeling is carried
out for Aluminum as fin material and compared with previous
method. The present results are also compared with those of two
other analytical methods and good agreement is shown.
Abstract: In this work, sorption of nickel from aqueous solution on hypnea valentiae, red macro algae, was investigated. Batch experiments have been carried out to find the effect of various parameters such as pH, temperature, sorbent dosage, metal concentration and contact time on the sorption of nickel using hypnea valentiae. Response surface methodology (RSM) is employed to optimize the process parameters. Based on the central composite design, quadratic model was developed to correlate the process variables to the response. The most influential factor on each experimental design response was identified from the analysis of variance (ANOVA). The optimum conditions for the sorption of nickel were found to be: pH – 5.1, temperature – 36.8oC, sorbent dosage – 5.1 g/L, metal concentration – 100 mg/L and contact time – 30 min. At these optimized conditions the maximum removal of nickel was found to be 91.97%. A coefficient of determination R2 value 0.9548 shows the fitness of response surface methodology in this work.
Abstract: The stop watch is used to measure the time required
for a certain event. This is different from normal clocks in many
ways, one of which is the accuracy of time. The stop watch requires
much more accuracy than the normal clocks. In this paper, an
ATmega8535 microcontroller was used to control the stop watch, by
which perfect accuracy can be ensured. For compiling the C code and
for loading the compiled .hex file into the microcontroller, AVR
studio and PonyProg were used respectively. The stop watch is also
different from traditional stop watches, as it contains two different
timing modes namely 'Split timing' and 'Lap timing'.
Abstract: In recent years there has been a continuous increase of
axle loads, tonnage, train speed and train length which has increased
both the productivity in the rail sector and the risk of rail breaks and
derailments. On the other hand, the environmental requirements (e.g.
noise reduction) for railway operations will become tighter in the
future. In our research we developed a new composite material which
does not change braking properties, is capable of taking extremely
high pressure loads, reduces noise and is environmentally friendly.
Part of our research was also the development of technology which
will be able to apply this material to the rail. The result of our
research was the system which reduces the wear out significantly and
almost completely eliminates the squealing noise at the same time,
and by using only one special material.
Abstract: Electrical discharge machining (EDM) is well
established machining technique mainly used to machine complex
geometries on difficult-to-machine materials and high strength
temperature resistant alloys. In the present research, the objective is
to study the shape of the electrode and establish the application of
liquid nitrogen in reducing distortion of the electrode during
electrical discharge machining of M2 grade high speed steel using
copper electrodes. Study of roundness was performed on the
electrode to observe the shape of the electrode for both conventional
EDM and EDM with cryogenically cooled electrode. Scanning
Electron Microscope (SEM) has been used to study the shape of
electrode tip. The effect of various parameters such as discharge
current and pulse on time has been studied to understand the behavior
of distortion of electrode. It has been concluded that the shape
retention is better in case of liquid nitrogen cooled electrode.
Abstract: A numerical study has been conducted to investigate the influence of fin pitch and relative humidity on the heat transfer performance of the fin-and-tube heat exchangers having plain fin geometry under dehumidifying conditions. The analysis is done using the ratio between the heat transfer coefficients in totally wet conditions and those in totally dry conditions using the appropriate correlations for both dry and wet conditions. For a constant relative humidity, it is found that the heat transfer coefficient increases with the increase of the air frontal velocity. By contrast, the fin efficiency decreases when the face velocity is increased. Apparently, this phenomenon is attributed to the path of condensate drainage. For the influence of relative humidity, the results showed an increase in heat transfer performance and a decrease in wet fin efficiency when relative humidity increases. This is due to the higher amount of mass transfer encountered at higher relative humidity. However, it is found that the effect of fin pitch on the heat transfer performance depends strongly on the face velocity. At lower frontal velocity the heat transfer increases with fin pitch. Conversely, an increase in fin pitch gives lower heat transfer coefficients when air velocity is increased.
Abstract: Identification of cancer genes that might anticipate
the clinical behaviors from different types of cancer disease is
challenging due to the huge number of genes and small number of
patients samples. The new method is being proposed based on
supervised learning of classification like support vector machines
(SVMs).A new solution is described by the introduction of the
Maximized Margin (MM) in the subset criterion, which permits to
get near the least generalization error rate. In class prediction
problem, gene selection is essential to improve the accuracy and to
identify genes for cancer disease. The performance of the new
method was evaluated with real-world data experiment. It can give
the better accuracy for classification.
Abstract: This paper examines the available experiment data for a copper bromide vapor laser (CuBr laser), emitting at two wavelengths - 510.6 and 578.2nm. Laser output power is estimated based on 10 independent input physical parameters. A classification and regression tree (CART) model is obtained which describes 97% of data. The resulting binary CART tree specifies which input parameters influence considerably each of the classification groups. This allows for a technical assessment that indicates which of these are the most significant for the manufacture and operation of the type of laser under consideration. The predicted values of the laser output power are also obtained depending on classification. This aids the design and development processes considerably.
Abstract: Total weighted tardiness is a measure of customer
satisfaction. Minimizing it represents satisfying the general
requirement of on-time delivery. In this research, we consider an ant
colony optimization (ACO) algorithm to solve the problem of
scheduling unrelated parallel machines to minimize total weighted
tardiness. The problem is NP-hard in the strong sense. Computational
results show that the proposed ACO algorithm is giving promising
results compared to other existing algorithms.
Abstract: Mammalian genomes contain large number of
retroelements (SINEs, LINEs and LTRs) which could affect
expression of protein coding genes through associated transcription
factor binding sites (TFBS). Activity of the retroelement-associated
TFBS in many genes is confirmed experimentally but their global
functional impact remains unclear. Human SINEs (Alu repeats) and
mouse SINEs (B1 and B2 repeats) are known to be clustered in GCrich
gene rich genome segments consistent with the view that they
can contribute to regulation of gene expression. We have shown
earlier that Alu are involved in formation of cis-regulatory modules
(clusters of TFBS) in human promoters, and other authors reported
that Alu located near promoter CpG islands have an increased
frequency of CpG dinucleotides suggesting that these Alu are
undermethylated. Human Alu and mouse B1/B2 elements have an
internal bipartite promoter for RNA polymerase III containing
conserved sequence motif called B-box which can bind basal
transcription complex TFIIIC. It has been recently shown that TFIIIC
binding to B-box leads to formation of a boundary which limits
spread of repressive chromatin modifications in S. pombe. SINEassociated
B-boxes may have similar function but conservation of
TFIIIC binding sites in SINEs located near mammalian promoters
has not been studied earlier. Here we analysed abundance and
distribution of retroelements (SINEs, LINEs and LTRs) in annotated
sequences of the Database of mammalian transcription start sites
(DBTSS). Fractions of SINEs in human and mouse promoters are
slightly lower than in all genome but >40% of human and mouse
promoters contain Alu or B1/B2 elements within -1000 to +200 bp
interval relative to transcription start site (TSS). Most of these SINEs
is associated with distal segments of promoters (-1000 to -200 bp
relative to TSS) indicating that their insertion at distances >200 bp
upstream of TSS is tolerated during evolution. Distribution of SINEs
in promoters correlates negatively with the distribution of CpG
sequences. Using analysis of abundance of 12-mer motifs from the
B1 and Alu consensus sequences in genome and DBTSS it has been
confirmed that some subsegments of Alu and B1 elements are poorly
conserved which depends in part on the presence of CpG
dinucleotides. One of these CpG-containing subsegments in B1
elements overlaps with SINE-associated B-box and it shows better
conservation in DBTSS compared to genomic sequences. It has been
also studied conservation in DBTSS and genome of the B-box
containing segments of old (AluJ, AluS) and young (AluY) Alu
repeats and found that CpG sequence of the B-box of old Alu is
better conserved in DBTSS than in genome. This indicates that Bbox-
associated CpGs in promoters are better protected from
methylation and mutation than B-box-associated CpGs in genomic
SINEs. These results are consistent with the view that potential
TFIIIC binding motifs in SINEs associated with human and mouse
promoters may be functionally important. These motifs may protect
promoters from repressive histone modifications which spread from
adjacent sequences. This can potentially explain well known
clustering of SINEs in GC-rich gene rich genome compartments and
existence of unmethylated CpG islands.
Abstract: A graph G is fractional k-covered if for each edge e of
G, there exists a fractional k-factor h, such that h(e) = 1. If k = 2,
then a fractional k-covered graph is called a fractional 2-covered
graph. The binding number bind(G) is defined as follows,
bind(G) = min{|NG(X)|
|X|
: ├ÿ = X Ôèå V (G),NG(X) = V (G)}.
In this paper, it is proved that G is fractional 2-covered if δ(G) ≥ 4
and bind(G) > 5
3 .
Abstract: We present a preliminary x-ray study on human-hair
microstructures for a health-state indicator, in particular a cancer
case. As an uncomplicated and low-cost method of x-ray technique,
the human-hair microstructure was analyzed by wide-angle x-ray
diffractions (XRD) and small-angle x-ray scattering (SAXS). The
XRD measurements exhibited the simply reflections at the d-spacing
of 28 Å, 9.4 Å and 4.4 Å representing to the periodic distance of the
protein matrix of the human-hair macrofibrous and the diameter and
the repeated spacing of the polypeptide alpha helixes of the
photofibrils of the human-hair microfibrous, respectively. When
compared to the normal cases, the unhealthy cases including to the
breast- and ovarian-cancer cases obtained higher normalized ratios of
the x-ray diffracting peaks of 9.4 Å and 4.4 Å. This likely resulted
from the varied distributions of microstructures by a molecular
alteration. As an elemental analysis by x-ray fluorescence (XRF), the
normalized quantitative ratios of zinc(Zn)/calcium(Ca) and
iron(Fe)/calcium(Ca) were determined. Analogously, both Zn/Ca and
Fe/Ca ratios of the unhealthy cases were obtained higher than both of
the normal cases were. Combining the structural analysis by XRD
measurements and the elemental analysis by XRF measurements
exhibited that the modified fibrous microstructures of hair samples
were in relation to their altered elemental compositions. Therefore,
these microstructural and elemental analyses of hair samples will be
benefit to associate with a diagnosis of cancer and genetic diseases.
This functional method would lower a risk of such diseases by the
early diagnosis. However, the high-intensity x-ray source, the highresolution
x-ray detector, and more hair samples are necessarily
desired to develop this x-ray technique and the efficiency would be
enhanced by including the skin and fingernail samples with the
human-hair analysis.
Abstract: In mammalian reproductive tract, the oviduct secretes
huge number of growth factors and cytokines that create an optimal
micro-environment for the initial stages of preimplantation embryos.
Secretion of these growth factors is stage-specific. Among them,
VEGF is a potent mitogen for vascular endothelium and stimulates
vascular permeability. Apart from angiogenesis, VEGF in the oviduct
may be involved in regulating the oocyte maturation and subsequent
developmental process during embryo production in vitro. In
experiment 1, to evaluate the effect of VEGF during IVM of porcine
COC and subsequent developmental ability after PA and SCNT. The
results from these experiments indicated that maturation rates among
the different VEGF concentrations were not significant different. In
experiment 2, total intracellular GSH concentrations of oocytes
matured with VEGF (5-50 ng/ml) were increased significantly
compared to a control and VEGF group (500 ng/ml). In experiment 3,
the blastocyst formation rates and total cell number per blastocyst
after parthenogenesis of oocytes matured with VEGF (5-50 ng/ml)
were increased significantly compared to a control and VEGF group
(500 ng/ml). Similarly, in experiment 4, the blastocyst formation rate
and total cell number per blastocyst after SCNT and IVF of oocytes
matured with VEGF (5 ng/ml) were significantly higher than that of
oocytes matured without VEGF group. In experiment 5, at 10 hour
after the onset of IVF, pronuclear formation rate was evaluated.
Monospermy was significantly higher in VEGF-matured oocytes than
in the control, and polyspermy and sperm penetration per oocyte
were significantly higher in the control group than in the VEGFmatured
oocytes. Supplementation with VEGF during IVM
significantly improved male pronuclear formation as compared with
the control. In experiment 6, type III cortical granule distribution in
oocytes was more common in VEGF-matured oocytes than in the
control. In conclusion, the present study suggested that
supplementation of VEGF during IVM may enhance the
developmental potential of porcine in vitro embryos through increase
of the intracellular GSH level, higher MPN formation and increased
fertilization rate as a consequence of an improved cytoplasmic
maturation.
Abstract: The unanticipated destruct of more of the steel moment frames in Northridge earthquake, altered class of regard to the beamto- column connections in moment frames. Panel zone is one the significant part of joints which, it-s stiffness and rigidity has an important effect on the behavior and ductility of the frame. Specifically that behavior of panel zone has a very significant effect on the special moment frames. In this paper , meanwhile the relations for modeling of panel zone in frames are expressed , special moment frames with different spans and stories were studied in the way of performance-based design. The frames designed in according with Iranian steel building code. The effect of panel zone is also considered and in the case of non-existence of performance level, by changing in intimacies and parameter of panel zone, performance level is considered.