Abstract: In this paper we deal with using Lego Mindstorms in
simulation of robotic systems with respect to cost reduction. Lego
Mindstorms kit contains broad variety of hardware components
which are required to simulate, program and test the robotics systems
in practice. Algorithm programming went in development
environment supplied together with Lego kit as in programming
language C# as well. Algorithm following the line, which we dealt
with in this paper, uses theoretical findings from area of controlling
circuits. PID controller has been chosen as controlling circuit whose
individual components were experimentally adjusted for optimal
motion of robot tracking the line. Data which are determined to
process by algorithm are collected by sensors which scan the
interface between black and white surfaces followed by robot. Based
on discovered facts Lego Mindstorms can be considered for low-cost
and capable kit to simulate real robotics systems.
Abstract: A vehicle driving with an Adaptive Cruise Control
System (ACC) is usually controlled decentrally, based on the
information of radar systems and in some publications based on
C2X-Communication (CACC) to guarantee stable platoons. In this
paper we present a Model Predictive Control (MPC) design of a
centralized, server-based ACC-System, whereby the vehicular platoon
is modeled and controlled as a whole. It is then proven that the
proposed MPC design guarantees asymptotic stability and hence
string stability of the platoon. The Networked MPC design is
chosen to be able to integrate system constraints optimally as well
as to reduce the effects of communication delay and packet loss.
The performance of the proposed controller is then simulated and
analyzed in an LTE communication scenario using the LTE/EPC
Network Simulator LENA, which is based on the ns-3 network
simulator.
Abstract: Single-phase, high band gap energy Zn0.5Mg0.5O films were grown under oxygen pressure, using pulse laser deposition with a Zn0.5Mg0.5O target. Structural characterization studies revealed that the crystal structures of the ZnX-1MgXO films could be controlled via changes in the oxygen pressure. TEM analysis showed that the thickness of the deposited Zn1-xMgxO thin films was 50–75 nm. As the oxygen pressure increased, we found that one axis of the crystals did not show a very significant increase in the crystallization compared with that observed at low oxygen pressure. The X-ray diffraction peak intensity for the hexagonal-ZnMgO (002) plane increased relative to that for the cubic-ZnMgO (111) plane. The corresponding c-axis of the h-ZnMgO lattice constant increased from 5.141 to 5.148 Å, and the a-axis of the c-ZnMgO lattice constant decreased from 4.255 to 4.250 Å. EDX analysis showed that the Mg content in the mixed-phase ZnMgO films decreased significantly, from 54.25 to 46.96 at.%. As the oxygen pressure was increased from 100 to 150 mTorr, the absorption edge red-shifted from 3.96 to 3.81 eV; however, a film grown at the highest oxygen pressure tested here (200 mTorr).
Abstract: In this paper will be discussed two coin´s sides
of crisis scenarios dynamics. On the one's side is negative role
of subsidiary scenario branches in its compactness weakening
by means unduly chaotic atomizing, having many interactive
feedbacks cases, increasing a value of a complexity here.
This negative role reflects the complexity of use cases, weakening
leader compliancy, which brings something as a ´readiness
for controlling capabilities provision´. Leader´s dissatisfaction has
zero compliancy, but factual it is a ´crossbar´ (interface in fact)
between planning and executing use cases. On the other side of this
coin, an advantage of rich scenarios embranchment is possible to see
in a support of response awareness, readiness, preparedness,
adaptability, creativity and flexibility. Here rich scenarios
embranchment contributes to the steadiness and resistance of scenario
mission actors. These all will be presented in live power-points
´Blazons´, modelled via DYVELOP (Dynamic Vector Logistics
of Processes) on the Conference.
Abstract: The advent of Flexible AC Transmission Systems (FACTS) is giving rise to a new family of power electronic equipment emerging for controlling and optimizing the performance of power system, e.g. STATCOM. Static synchronous Compensator (STATCOM) is a commonly used FACTS device and has been successfully applied in power systems. In this sense, superconducting magnetic energy storage (SMES) in integration with a static synchronous compensator (STATCOM) is capable of supplying power systems with both active and reactive powers simultaneously and very rapidly, and thus is able to enhance the security dramatically. In this paper the structure and characteristics of the STATCOM/SMES is proposed. In addition, using a proper control scheme, STATCOM/ SMES is tested on an IEEE 3-bus system and more effective performance of the presented STATCOM/SMES compensator is evaluated with alone STATCOM through the dynamic simulation by using PSCAD/EMTDC software.
Abstract: The purpose of this study was to address and comparison of the attitudes towards the statistics course for undergraduate students. Data were collected from 120 students in Faculty of Sciences and Technology, Suan Sunandha Rajabhat University who enrolled in the statistics course. The quantitative approach was used to investigate the assessment and comparison of attitudes towards statistics course. It was revealed that the overall attitudes somewhat agree both in pre-test and post-test. In addition, the comparison of students’ attitudes towards the statistic course (Form A) has no difference in the overall attitudes. However, there is statistical significance in all dimensions and overall attitudes towards the statistics course (Form B).
Abstract: In this paper, a 2DOF (two degrees of freedom) PID (Proportional-Integral-Derivative) controller based on MPC (Model predictive control) algorithm fo slip suppression of EV (Electric Vehicle) under braking is proposed. The proposed method aims to improve the safety and the stability of EVs under braking by controlling the wheel slip ration. There also include numerical simulation results to demonstrate the effectiveness of the method.
Abstract: In industrial environments, the heat exchanger is a
necessary component to any strategy of energy conversion. Much of
thermal energy used in industrial processes passes at least one times
by a heat exchanger, and methods systems recovering thermal
energy.
This survey paper tries to presents in a systemic way an sample
control of a heat exchanger by comparison between three controllers
LQR (linear quadratic regulator), PID (proportional, integrator and
derivate) and Pole Placement. All of these controllers are used mainly
in industrial sectors (chemicals, petrochemicals, steel, food
processing, energy production, etc…) of transportation (automotive,
aeronautics), but also in the residential sector and tertiary (heating, air
conditioning, etc...) The choice of a heat exchanger, for a given
application depends on many parameters: field temperature and
pressure of fluids, and physical properties of aggressive fluids,
maintenance and space. It is clear that the fact of having an
exchanger appropriate, well-sized, well made and well used allows
gain efficiency and energy processes.
Abstract: The increasing penetration of Distributed Generation and storage connected to the distribution network via PWM converters increases the possibility of a DC-component (offset) in voltage or current flowing into the grid. This occurs when even harmonics are present in the network voltage. DC-components can affect the operation and safety of several grid components. Therefore, an investigation of the way they are produced is important in order to take appropriate measures for their elimination. Further research on DC-components that appear on output voltage of converters is performed for different parameters of PWM technique and characteristics of even harmonics.
Abstract: To avoid battery assisted tags with limited lifetime batteries, it is proposed here to replace them by energy harvesting
systems, able to feed from local environment. This would allow total
independence to RFID systems, very interesting for applications
where tag removal from its location is not possible. Example is here
described for luggage safety in airports, and is easily extendable to similar situation in terms of operation constraints. The idea is to fix
RFID tag with energy harvesting system not only to identify luggage
but also to supply an embedded microcontroller with a sensor
delivering luggage weight making it impossible to add or to remove
anything from the luggage during transit phases. The aim is to
optimize the harvested energy for such RFID applications, and to
study in which limits these applications are theoretically possible.
Proposed energy harvester is based on two energy sources:
piezoelectricity and electromagnetic waves, so that when the luggage
is moving on ground transportation to airline counters, the piezo
module supplies the tag and its microcontroller, while the RF module
operates during luggage transit thanks to readers located along the
way. Tag location on the luggage is analyzed to get best vibrations, as
well as harvester better choice for optimizing the energy supply
depending on applications and the amount of energy harvested during
a period of time. Effects of system parameters (RFID UHF
frequencies, limit distance between the tag and the antenna necessary
to harvest energy, produced voltage and voltage threshold) are
discussed and working conditions for such system are delimited.
Abstract: According to the independence, accuracy and controllability of the driving/braking torque of the distributed drive electric vehicle, a control strategy of differential drive assisted steering was designed. Firstly, the assisted curve under different speed and steering wheel torque was developed and the differential torques were distributed to the right and left front wheels. Then the steering return ability assisted control algorithm was designed. At last, the joint simulation was conducted by CarSim/Simulink. The result indicated: the differential drive assisted steering algorithm could provide enough steering drive-assisted under low speed and improve the steering portability. Along with the increase of the speed, the provided steering drive-assisted decreased. With the control algorithm, the steering stiffness of the steering system increased along with the increase of the speed, which ensures the driver’s road feeling. The control algorithm of differential drive assisted steering could avoid the understeer under low speed effectively.
Abstract: In this paper, a sliding mode control method based on the passivity approach is proposed to control the position of surface-mounted permanent magnet synchronous motors (PMSMs). Firstly, the dynamics of a PMSM was proved to be strictly passive. The position controller with an adaptive law was used to estimate the load torque to eliminate the chattering effects associated with the conventional sliding mode controller. The stability analysis of the overall position control system was carried out by adopting the passivity theorem instead of Lyapunov-type arguments. Finally, experimental results were provided to show that the good position tracking can be obtained, and exhibit robustness in the variations of the motor parameters and load torque disturbances.
Abstract: Historically, actuators’ redundancy was used to deal
with faults occurring suddenly in flight systems. This technique was
generally expensive, time consuming and involves increased weight
and space in the system. Therefore, nowadays, the on-line fault
diagnosis of actuators and accommodation plays a major role in the
design of avionic systems. These approaches, known as Fault
Tolerant Flight Control systems (FTFCs) are able to adapt to such
sudden faults while keeping avionics systems lighter and less
expensive. In this paper, a (FTFC) system based on the Geometric
Approach and a Reconfigurable Flight Control (RFC) are presented.
The Geometric approach is used for cosmic ray fault reconstruction,
while Sliding Mode Control (SMC) based on Lyapunov stability
theory is designed for the reconfiguration of the controller in order to
compensate the fault effect. Matlab®/Simulink® simulations are
performed to illustrate the effectiveness and robustness of the
proposed flight control system against actuators’ faulty signal caused
by cosmic rays. The results demonstrate the successful real-time
implementation of the proposed FTFC system on a non-linear 6 DOF
aircraft model.
Abstract: This paper presents the design and implementation of a sliding-mod controller for tracking servo of optical disk drives. The tracking servo is majorly subject to two disturbance sources: radial run-out and shock. The lateral run-out disturbance is mostly repeatable, and a model of such disturbance is incorporated into the controller design to effectively compensate for it. Meanwhile, as a shock disturbance is usually non-repeatable and unpredictable, the sliding-mode controller is employed for its robustness to abrupt perturbations. As a result, a sliding-mode controller design based on the internal model principle is tailored for tracking servo of optical disk drives in order to deal with these two major disturbances. Experimental comparative studies are conducted to investigate the effectiveness of the specially designed controller.
Abstract: It is well known that photovoltaic (PV) cells are an attractive source of energy. Abundant and ubiquitous, this source is one of the important renewable energy sources that have been increasing worldwide year by year. However, in the V-P characteristic curve of GPV, there is a maximum point called the maximum power point (MPP) which depends closely on the variation of atmospheric conditions and the rotation of the earth. In fact, such characteristics outputs are nonlinear and change with variations of temperature and irradiation, so we need a controller named maximum power point tracker MPPT to extract the maximum power at the terminals of photovoltaic generator. In this context, the authors propose here to study the modeling of a photovoltaic system and to find an appropriate method for optimizing the operation of the PV generator using two intelligent controllers respectively to track this point. The first one is based on artificial neural networks and the second on fuzzy logic. After the conception and the integration of each controller in the global process, the performances are examined and compared through a series of simulation. These two controller have prove by their results good tracking of the MPPT compare with the other method which are proposed up to now.
Abstract: The purpose of the study was to examine the
relationships between objectively measured physical activity levels
(PALs), enjoyment of physical activity (EPA), and body mass index
(BMI) among adolescents. A total of 188 12-14-year-old Bruneian
secondary school adolescents (88 boys and 100 girls) voluntarily took
part in this study. Subjects wore the RT3 accelerometer for seven
consecutive days in order to measure their PALs. Times of students’
engagement in total (TPA), light (LPA), moderate (MPV), and
vigorous PA (VPA) were obtained from the accelerometer. Their
BMIs were calculated from their body height and weight. Physical
Activity Enjoyment Scale (PACES) was administrated to obtain their
EPA levels. Four key enjoyment factors including fun factors,
positive perceptions, unexciting in doing activities, and negative
perceptions were identified. Subjects’ social economic status (SES)
was provided by school administration. Results show that all the
adolescents did not meet the recommended PA guidelines even
though boys were engaged in more MVPA than girls. No
relationships were found between BMI and all PALs in both boys and
girls. BMI was significantly related to the PACES scores (r = -.22, p
= 0.01), fun factors (r = -.20, p = 0.05) and positive perceptions (r =-
.21, p < 0.05). The PACES scores were significantly related to LPA
(r = .18, p = 0.01) but not related to MVPA (r = .04, p > 0.05). After
controlling for age and SES, BMI was only significantly related to
the PACES scores in girls (r = -.27, p < .01) but boys (r = -.06, p >
0.05). Fun factors were significantly related to LPA and MVPA (p
Abstract: One of the main features of the Maghreb is its linguistic richness. The multilingualism is a fact which always marked the Maghreb since the beginning of the history up to know. Since the arrival of the Phoenicians, followed by the Carthaginians, Romans, and Arabs, etc, there was a social group in the Maghreb which controlled two kinds of idioms. The libyc one remained, despite everything, the local language used by the major part of the population. This language had a support of written transmission attested by many inscriptions. Among all the forms of the Maghreb writing, this alphabet, however, continues to cause a certain number of questions about the origin and the date of its appearance. The archaeological, linguistic and historical data remain insufficient to answer these questions. This did not prevent the researchers from giving an opinion. In order to answer these questions we will expose here the various assumptions adopted by various authors who are founded on more or less explicit arguments. We will also speak about the various forms taken by the libyc writing during antiquity.
Abstract: In this paper, the stability analysis of a GA-Based adaptive fuzzy sliding model controller for a nonlinear system is discussed. First, a nonlinear plant is well-approximated and described with a reference model and a fuzzy model, both involving FLC rules. Then, FLC rules and the consequent parameter are decided on via an Evolved Bat Algorithm (EBA). After this, we guarantee a new tracking performance inequality for the control system. The tracking problem is characterized to solve an eigenvalue problem (EVP). Next, an adaptive fuzzy sliding model controller (AFSMC) is proposed to stabilize the system so as to achieve good control performance. Lyapunov’s direct method can be used to ensure the stability of the nonlinear system. It is shown that the stability analysis can reduce nonlinear systems into a linear matrix inequality (LMI) problem. Finally, a numerical simulation is provided to demonstrate the control methodology.
Abstract: Systems running these days are huge, complex and exist in many versions. Controlling these versions and tracking their changes became a very hard process as some versions are created using meaningless names or specifications. Many versions of a system are created with no clear difference between them. This leads to mismatching between a user’s request and the version he gets. In this paper, we present a system versions meta-modeling approach that produces versions based on system’s features. This model reduced the number of steps needed to configure a release and gave each version its unique specifications. This approach is applicable for systems that use features in its specification.
Abstract: Nitrogen is among the main nutrients encouraging the growth of organic matter and algae which cause eutrophication in water bodies. Therefore, its removal from wastewater has become a worldwide emerging concern. In this research, an innovative Membrane Bioreactor (MBR) system named “moving bed membrane bioreactor (MBMBR)” was developed and investigated under intermittently-aerated mode for simultaneous removal of organic carbon and nitrogen.
Results indicated that the variation of the intermittently aerated duration did not have an apparent impact on COD and NH4+–N removal rate, yielding the effluent with average COD and NH4+–N removal efficiency of more than 92 and 91% respectively. However, in the intermittently aerated cycle of (continuously aeration/0s mix), (aeration 90s/mix 90s) and (aeration 90s/mix 180s); the average TN removal efficiency was 67.6%, 69.5% and 87.8% respectively. At the same time, their nitrite accumulation rate was 4.5%, 49.1% and 79.4% respectively. These results indicate that the intermittently aerated mode is an efficient way to controlling the nitrification to stop at nitrition; and also the length of anoxic duration is a key factor in improving TN removal.