Abstract: Design concepts of real-time embedded system can be
realized initially by introducing novel design approaches. In this
literature, model based design approach and in-the-loop testing were
employed early in the conceptual and preliminary phase to formulate
design requirements and perform quick real-time verification. The
design and analysis methodology includes simulation analysis, model
based testing, and in-the-loop testing. The design of conceptual driveby-
wire, or DBW, algorithm for electronic control unit, or ECU, was
presented to demonstrate the conceptual design process, analysis, and
functionality evaluation. The concepts of DBW ECU function can be
implemented in the vehicle system to improve electric vehicle, or EV,
conversion drivability. However, within a new development process,
conceptual ECU functions and parameters are needed to be evaluated.
As a result, the testing system was employed to support conceptual
DBW ECU functions evaluation. For the current setup, the system
components were consisted of actual DBW ECU hardware, electric
vehicle models, and control area network or CAN protocol. The
vehicle models and CAN bus interface were both implemented as
real-time applications where ECU and CAN protocol functionality
were verified according to the design requirements. The proposed
system could potentially benefit in performing rapid real-time
analysis of design parameters for conceptual system or software
algorithm development.
Abstract: Agro-industry is one of major industries that have
strong impacts on national economic incomes, growth, stability, and
sustainable development. Moreover, this industry also has strong
influences on social, cultural and political issues. Furthermore, this
industry, as producing primary and secondary products, is facing
challenges from such diverse factors such as demand inconsistency,
intense international competition, technological advancements and
new competitors. In order to maintain and to improve industry’s
competitiveness in both domestics and international markets, science
and technology are key factors. Besides hard sciences and
technologies, modern industrial engineering concepts such as Just in
Time (JIT) Total Quality Management (TQM), Quick Response
(QR), Supply Chain Management (SCM) and Lean can be very
effective to support to increase efficiency and effectiveness of these
agricultural products on world stage. Onion is one of Thailand’s
major export products which bring back national incomes. But, it is
also facing challenges in many ways. This paper focused its interests
in onion packing process and its related activities such as storage and
shipment from one of major packing plant and storage in Mae Wang
District, Chiang Mai, Thailand, by applying Toyota Production
System (TPS) or Lean concepts, to improve process capability
throughout the entire packing and distribution process which will be
profitable for the whole onion supply chain. And it will be beneficial
to other related agricultural products in Thailand and other ASEAN
countries.
Abstract: This paper investigates the benefits of deliberately
unbalancing both operation time means (MTs) and unreliability
(failure and repair rates) for non-automated production lines. The
lines were simulated with various line lengths, buffer capacities,
degrees of imbalance and patterns of MT and unreliability imbalance.
Data on two performance measures, namely throughput (TR) and
average buffer level (ABL) were gathered, analyzed and compared to
a balanced line counterpart. A number of conclusions were made
with respect to the ranking of configurations, as well as to the
relationships among the independent design parameters and the
dependent variables. It was found that the best configurations are a
balanced line arrangement and a monotone decreasing MT order,
coupled with either a decreasing or a bowl unreliability configuration,
with the first generally resulting in a reduced TR and the second
leading to a lower ABL than those of a balanced line.
Abstract: Big Data and analytics have gained a huge momentum
in recent years. Big Data feeds into the field of Learning Analytics
(LA) that may allow academic institutions to better understand the
learners’ needs and proactively address them. Hence, it is important
to have an understanding of Big Data and its applications. The
purpose of this descriptive paper is to provide an overview of Big
Data, the technologies used in Big Data, and some of the applications
of Big Data in education. Additionally, it discusses some of the
concerns related to Big Data and current research trends. While Big
Data can provide big benefits, it is important that institutions
understand their own needs, infrastructure, resources, and limitation
before jumping on the Big Data bandwagon.
Abstract: This study presented to reduce earthquake damage and
emergency rehabilitation of critical structures such as schools, hightech
factories, and hospitals due to strong ground motions associated
with climate changes. Regarding recent trend, a strong earthquake
causes serious damage to critical structures and then the critical
structure might be influenced by sequence aftershocks (or tsunami)
due to fault plane adjustments. Therefore, in order to improve seismic
performance of critical structures, retrofitted or strengthening study
of the structures under aftershocks sequence after emergency
rehabilitation of the structures subjected to strong earthquakes is
widely carried out. Consequently, this study used composite material
for emergency rehabilitation of the structure rather than concrete and
steel materials because of high strength and stiffness, lightweight,
rapid manufacturing, and dynamic performance. Also, this study was
to develop or improve the seismic performance or seismic retrofit of
critical structures subjected to strong ground motions and earthquake
aftershocks, by utilizing GFRP-Corrugated Infill Panels (GCIP).
Abstract: Organizational tendencies towards computer-based
information processing have been observed noticeably in the
third-world countries. Many enterprises are taking major initiatives
towards computerized working environment because of massive
benefits of computer-based information processing. However,
designing and developing information resource management software
for small and mid-size enterprises under budget costs and strict
deadline is always challenging for software engineers. Therefore, we
introduced an approach to design mid-size enterprise software by
using the Waterfall model, which is one of the SDLC (Software
Development Life Cycles), in a cost effective way. To fulfill research
objectives, in this study, we developed mid-sized enterprise software
named “BSK Management System” that assists enterprise software
clients with information resource management and perform complex
organizational tasks. Waterfall model phases have been applied to
ensure that all functions, user requirements, strategic goals, and
objectives are met. In addition, Rich Picture, Structured English, and
Data Dictionary have been implemented and investigated properly in
engineering manner. Furthermore, an assessment survey with 20
participants has been conducted to investigate the usability and
performance of the proposed software. The survey results indicated
that our system featured simple interfaces, easy operation and
maintenance, quick processing, and reliable and accurate transactions.
Abstract: Moringa oleifera is a nutritious vegetable tree with
varieties of potential uses, as almost every part of the Moringa
oleifera tree can be used for food. This study was conducted in Oyo
State, Nigeria, to find out the level of acceptability of Moringa
oleifera diversified products among rural and urban dwellers.
Purposive sampling was used to select two local governments’ areas.
Stratified sampling technique was also used to select one community
each from rural and urban areas while snowball sampling technique
was used to select ten respondents each from the two communities,
making a total number of forty respondents. Data were analyzed
using frequencies, percentages, Chi-square, Pearson Product Moment
Correlation and regression analysis. Result from the study revealed
that majority of the respondents (80%) fell within the age range of
20-49 years and 55% of them were male, 55% were married, 70% of
them were Christians, 80% of them had tertiary education. The result
also showed that 85% were aware of the Moringa plant and (65%) of
them have consumed Moringa oleifera and the perception statements
on the benefits of Moringa oleifera indicated that (52.5%) of the
respondents rated Moringa oleifera to be favorable, most of them had
high acceptability for Moringa egusi soup, Moringa tea, Moringa pap
and yam pottage with Moringa. The result of the hypotheses testing
showed that there is a significant relationship between sex of the
respondents and acceptability of the diversified Moringa oleifera
products (x2=6.465, p = 0.011). There is also a significant
relationship between family size of the respondents level of
acceptability of the Moringa oleifera products (r = 0.327, p = 0.040).
Based on the level of acceptability of Moringa oleifera diversified
products; the plant is of great economic importance to the populace.
Therefore, there should be more public awareness through the media
to enlighten people on the beneficial effects of Moringa oleifera.
Abstract: The advent of social networking technologies has been
met with mixed reactions in academic and corporate circles around
the world. This study explored the influence of social network in
current era, the relation being maintained between the Social
networking site and its user by the extent of use, benefits and latest
technologies. The study followed a descriptive research design
wherein a questionnaire was used as the main research tool. The data
collected was analyzed using SPSS 16. Data was gathered from 1205
users and analyzed in accordance with the objectives of the study.
The analysis of the results seem to suggest that the majority of users
were mainly using Facebook, despite of concerns raised about the
disclosure of personal information on social network sites, users
continue to disclose huge quantity of personal information, they find
that reading privacy policy is time consuming and changes made can
result into improper settings.
Abstract: One of the crucial parameters of digital cryptographic
systems is the selection of the keys used and their distribution. The
randomness of the keys has a strong impact on the system’s security
strength being difficult to be predicted, guessed, reproduced, or
discovered by a cryptanalyst. Therefore, adequate key randomness
generation is still sought for the benefit of stronger cryptosystems.
This paper suggests an algorithm designed to generate and test
pseudo random number sequences intended for cryptographic
applications. This algorithm is based on mathematically manipulating
a publically agreed upon information between sender and receiver
over a public channel. This information is used as a seed for
performing some mathematical functions in order to generate a
sequence of pseudorandom numbers that will be used for
encryption/decryption purposes. This manipulation involves
permutations and substitutions that fulfill Shannon’s principle of
“confusion and diffusion”. ASCII code characters were utilized in the
generation process instead of using bit strings initially, which adds
more flexibility in testing different seed values. Finally, the obtained
results would indicate sound difficulty of guessing keys by attackers.
Abstract: We proposed a Hyperbolic Gompertz Growth Model
(HGGM), which was developed by introducing a shape parameter
(allometric). This was achieved by convoluting hyperbolic sine
function on the intrinsic rate of growth in the classical gompertz
growth equation. The resulting integral solution obtained
deterministically was reprogrammed into a statistical model and used
in modeling the height and diameter of Pines (Pinus caribaea). Its
ability in model prediction was compared with the classical gompertz
growth model, an approach which mimicked the natural variability of
height/diameter increment with respect to age and therefore provides
a more realistic height/diameter predictions using goodness of fit
tests and model selection criteria. The Kolmogorov Smirnov test and
Shapiro-Wilk test was also used to test the compliance of the error
term to normality assumptions while the independence of the error
term was confirmed using the runs test. The mean function of top
height/Dbh over age using the two models under study predicted
closely the observed values of top height/Dbh in the hyperbolic
gompertz growth models better than the source model (classical
gompertz growth model) while the results of R2, Adj. R2, MSE and
AIC confirmed the predictive power of the Hyperbolic Gompertz
growth models over its source model.
Abstract: This paper presents dynamic models of distributed
generators (DG) and investigates dynamic behavior of the DG units
in the micro grid system. The DG units include photovoltaic and fuel
cell sources. The voltage source inverter is adopted since the
electronic interface which can be equipped with its controller to keep
stability of the micro grid during small signal dynamics. This paper
also introduces power management strategies and implements the DG
load sharing concept to keep the micro grid operation in gridconnected
and islanding modes of operation. The results demonstrate
the operation and performance of the photovoltaic and fuel cell as
distributed generators in a micro grid. The entire control system in
the micro grid is developed by combining the benefits of the power
control and the voltage control strategies. Simulation results are all
reported, confirming the validity of the proposed control technique.
Abstract: In emerging economies, recycling is an opportunity
for the cities to increase the lifespan of sanitary landfills, reduce the
costs of the solid waste management, decrease the environmental
problems of the waste treatment through reincorporate waste in the
productive cycle and protect and develop people’s livelihoods of
informal waste pickers. However, few studies have analysed the
possibilities and strategies to integrate formal and informal sectors in
the solid waste management for the benefit of both. This study seek
to make a strength, weakness, opportunity, and threat (SWOT)
analysis in three recycling associations of Bogotá with the aim to
understand and determine the situation of recycling from perspective
of informal sector in its transition to enter as authorized waste
providers. Data used in the analysis are derived from multiple
strategies such as literature review, the Bogota’s recycling database,
focus group meetings, governmental reports, national laws and
regulations and specific interviews with key stakeholders. Results of
this study show as the main stakeholders of formal and informal
sector of waste management can identify the internal and internal
conditions of recycling in Bogotá. Several strategies were designed
based on the SWOTs determined, could be useful for Bogotá to
advance and promote recycling as a key strategy for integrated
sustainable waste management in the city.
Abstract: All the software engineering researches and best
industry practices aim at providing software products with high
degree of quality and functionality at low cost and less time. These
requirements are addressed by the Component Based Software
Engineering (CBSE) as well. CBSE, which deals with the software
construction by components’ assembly, is a revolutionary extension
of Software Engineering. CBSE must define and describe processes
to assure timely completion of high quality software systems that are
composed of a variety of pre built software components. Though
these features provide distinct and visible benefits in software design
and programming, they also raise some challenging problems. The
aim of this work is to summarize the pertinent issues and
considerations in CBSE to make an understanding in forms of
concepts and observations that may lead to development of newer
ways of dealing with the problems and challenges in CBSE.
Abstract: The main objective of this paper is to provide a new
methodology for road safety assessment in Oman through the
development of suitable accident prediction models. GLM technique
with Poisson or NBR using SAS package was carried out to develop
these models. The paper utilized the accidents data of 31 un-signalized
T-intersections during three years. Five goodness-of-fit
measures were used to assess the overall quality of the developed
models. Two types of models were developed separately; the flow-based
models including only traffic exposure functions, and the full
models containing both exposure functions and other significant
geometry and traffic variables.
The results show that, traffic exposure functions produced much
better fit to the accident data. The most effective geometric variables
were major-road mean speed, minor-road 85th percentile speed,
major-road lane width, distance to the nearest junction, and right-turn
curb radius.
The developed models can be used for intersection treatment or
upgrading and specify the appropriate design parameters of T-intersections.
Finally, the models presented in this thesis reflect the intersection
conditions in Oman and could represent the typical conditions in
several countries in the middle east area, especially gulf countries.
Abstract: This study examined how individuals in their
respective teams contributed to innovation performance besides
defining the term of innovation in their own respective views. This
study also identified factors that motivated University staff to
contribute to the innovation products. In addition, it examined
whether there is a significant relationship between professional
training level and the length of service among university staff
towards innovation and to what extent do the two variables
contributed towards innovative products. The significance of this
study is that it revealed the strengths and weaknesses of the
university staff when contributing to innovation performance.
Stratified-random sampling was employed to determine the samples
representing the population of lecturers in the study, involving 123
lecturers in one of the local universities in Malaysia. The method
employed to analyze the data is through categorizing into themes for
the open-ended questions besides using descriptive and inferential
statistics for the quantitative data. This study revealed that two types
of definition for the term “innovation” exist among the university
staff, namely, creation of new product or new approach to do things
as well as value-added creative way to upgrade or improve existing
process and service to be more efficient. This study found that the
most prominent factor that propels them towards innovation is to
improve the product in order to benefit users, followed by selfsatisfaction
and recognition. This implies that the staff in the
organization viewed the creation of innovative products as a process
of growth to fulfill the needs of others and also to realize their
personal potential. This study also found that there was only a
significant relationship between the professional training level and
the length of service of 4 - 6 years among the university staff. The
rest of the groups based on the length of service showed that there
was no significant relationship with the professional training level
towards innovation. Moreover, results of the study on directional
measures depicted that the relationship for the length of service of 4-
6 years with professional training level among the university staff is
quite weak. This implies that good organization management lies on
the shoulders of the key leaders who enlighten the path to be
followed by the staff.
Abstract: After the internet explosion in the 90’s, technology
was immediately integrated into the school system. Technology
which symbolizes advancement in human knowledge was seen as a
setback by many educators. Efforts have been made to help stem this
erroneous believes and help educators realize the benefits of
technology and ways of implementing it in the classrooms especially
in the sciences. This advancement created a constantly expanding gap
between the pupil’s perception on the use of technology within the
learning atmosphere and the teacher’s perception and limitations
hence, the focus of this paper is on the need to refocus on the use of
Science and Technology in enhancing children’s potentials in
learning at school especially in Science for sustainable development
in Nigeria. The paper recommended measures for facilitating the
sustenance of science and technology in Nigerian schools so as to
enhance the potentials of our children in Science and Technology for
a better tomorrow.
Abstract: There are several possibilities of reducing the required
amount of cement in concrete production. Natural zeolite is one of
the raw materials which can partly substitute Portland cement. The
effort to reduce the amount of Portland cement used in concrete
production is brings both economical as well as ecological benefits.
The paper presents the properties of concrete containing natural
zeolite as an active admixture in the concrete which partly substitutes
Portland cement. The properties discussed here bring information
about the basic mechanical properties and frost resistance of concrete
containing zeolite. The properties of concretes with the admixture of
zeolite are compared with a reference concrete with no content of
zeolite. The properties of the individual concretes are observed for
360 days.
Abstract: The construction industry has been demonstrating
increased growth and importance in Brazil’s national economic
development. This study aims to evaluate the financial performance
of the leading companies in the construction sector in Brazil in the
period from 2009 to 2012. An analysis is made of the capital
structure, liquidity, and profitability of the six largest companies in
the construction sector in Brazil: Brookfield, Cyrela, Gafisa, MRV,
PDG and Rossi. The results are then compared with standard industry
ratios. It was found that among the companies analyzed, MRV and
Cyrela showed the best relative performance in the period under
consideration.
Abstract: This exploratory study gives an overview of the
evolution of the main financial and performance indicators of the
Academic Spin-Off’s and High Growth Academic Spin-Off’s in year
3 and year 6 after its creation in the region of Catalonia in Spain. The
study compares and evaluates results of these different measures of
performance and the degree of success of these companies for each
University.
We found that the average Catalonian Academic Spin-Off is small
and have not achieved the sustainability stage at year 6. On the
contrary, a small group of High Growth Academic Spin-Off’s
exhibits robust performance with high profits in year 6. Our results
support the need to increase selectivity and support for these
companies especially near year 3, because are the ones that will bring
wealth and employment. University role as an investor has rigid
norms and habits that impede an efficient economic return from their
ASO investment.
Universities with high performance on sales and employment in
year 3 not always could sustain this growth in year 6 because their
ASO’s are not profitable. On the contrary, profitable ASO exhibit
superior performance in all measurement indicators in year 6. We
advocate the need of a balanced growth (with profits) as a way to
obtain subsequent continuous growth.
Abstract: The aim of this paper is to understand emerging
learning conditions, when a visual analytics is implemented and used
in K 12 (education). To date, little attention has been paid to the role
visual analytics (digital media and technology that highlight visual
data communication in order to support analytical tasks) can play in
education, and to the extent to which these tools can process
actionable data for young students. This study was conducted in three
public K 12 schools, in four social science classes with students aged
10 to 13 years, over a period of two to four weeks at each school.
Empirical data were generated using video observations and analyzed
with help of metaphors within Actor-network theory (ANT). The
learning conditions are found to be distinguished by broad
complexity, characterized by four dimensions. These emerge from
the actors’ deeply intertwined relations in the activities. The paper
argues in relation to the found dimensions that novel approaches to
teaching and learning could benefit students’ knowledge building as
they work with visual analytics, analyzing visualized data.