Abstract: Recently, Genetic Algorithms (GA) and Differential
Evolution (DE) algorithm technique have attracted considerable
attention among various modern heuristic optimization techniques.
Since the two approaches are supposed to find a solution to a given
objective function but employ different strategies and computational
effort, it is appropriate to compare their performance. This paper
presents the application and performance comparison of DE and GA
optimization techniques, for flexible ac transmission system
(FACTS)-based controller design. The design objective is to enhance
the power system stability. The design problem of the FACTS-based
controller is formulated as an optimization problem and both the PSO
and GA optimization techniques are employed to search for optimal
controller parameters. The performance of both optimization
techniques has been compared. Further, the optimized controllers are
tested on a weekly connected power system subjected to different
disturbances, and their performance is compared with the
conventional power system stabilizer (CPSS). The eigenvalue
analysis and non-linear simulation results are presented and
compared to show the effectiveness of both the techniques in
designing a FACTS-based controller, to enhance power system
stability.
Abstract: The H.264/AVC standard uses an intra prediction, 9
directional modes for 4x4 luma blocks and 8x8 luma blocks, 4
directional modes for 16x16 macroblock and 8x8 chroma blocks,
respectively. It means that, for a macroblock, it has to perform 736
different RDO calculation before a best RDO modes is determined.
With this Multiple intra-mode prediction, intra coding of H.264/AVC
offers a considerably higher improvement in coding efficiency
compared to other compression standards, but computational
complexity is increased significantly. This paper presents a fast intra
prediction algorithm for H.264/AVC intra prediction based a
characteristic of homogeneity information. In this study, the gradient
prediction method used to predict the homogeneous area and the
quadratic prediction function used to predict the nonhomogeneous
area. Based on the correlation between the homogeneity and block
size, the smaller block is predicted by gradient prediction and
quadratic prediction, so the bigger block is predicted by gradient
prediction. Experimental results are presented to show that the
proposed method reduce the complexity by up to 76.07%
maintaining the similar PSNR quality with about 1.94%bit rate
increase in average.
Abstract: This study reports the preparation of soft magnetic ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213 mm and, with a thickness of approximately 22 μm 2 μm. The microstructure and magnetic properties of the ribbons were characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide ribbon, the magnetic responses are not uniformly distributed. To understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: METIS is the Multi Element Telescope for Imaging
and Spectroscopy, a Coronagraph aboard the European Space
Agency-s Solar Orbiter Mission aimed at the observation of the solar
corona via both VIS and UV/EUV narrow-band imaging and spectroscopy. METIS, with its multi-wavelength capabilities, will
study in detail the physical processes responsible for the corona heating and the origin and properties of the slow and fast solar wind.
METIS electronics will collect and process scientific data thanks to its detectors proximity electronics, the digital front-end subsystem
electronics and the MPPU, the Main Power and Processing Unit,
hosting a space-qualified processor, memories and some rad-hard
FPGAs acting as digital controllers.This paper reports on the overall
METIS electronics architecture and data processing capabilities
conceived to address all the scientific issues as a trade-off solution between requirements and allocated resources, just before the
Preliminary Design Review as an ESA milestone in April 2012.
Abstract: Segmentation is an important step in medical image
analysis and classification for radiological evaluation or computer
aided diagnosis. The CAD (Computer Aided Diagnosis ) of lung CT
generally first segment the area of interest (lung) and then analyze
the separately obtained area for nodule detection in order to
diagnosis the disease. For normal lung, segmentation can be
performed by making use of excellent contrast between air and
surrounding tissues. However this approach fails when lung is
affected by high density pathology. Dense pathologies are present in
approximately a fifth of clinical scans, and for computer analysis
such as detection and quantification of abnormal areas it is vital that
the entire and perfectly lung part of the image is provided and no
part, as present in the original image be eradicated. In this paper we
have proposed a lung segmentation technique which accurately
segment the lung parenchyma from lung CT Scan images. The
algorithm was tested against the 25 datasets of different patients
received from Ackron Univeristy, USA and AGA Khan Medical
University, Karachi, Pakistan.
Abstract: Local Linear Neuro-Fuzzy Models (LLNFM) like other neuro- fuzzy systems are adaptive networks and provide robust learning capabilities and are widely utilized in various applications such as pattern recognition, system identification, image processing and prediction. Local linear model tree (LOLIMOT) is a type of Takagi-Sugeno-Kang neuro fuzzy algorithm which has proven its efficiency compared with other neuro fuzzy networks in learning the nonlinear systems and pattern recognition. In this paper, a dedicated reconfigurable and parallel processing hardware for LOLIMOT algorithm and its applications are presented. This hardware realizes on-chip learning which gives it the capability to work as a standalone device in a system. The synthesis results on FPGA platforms show its potential to improve the speed at least 250 of times faster than software implemented algorithms.
Abstract: This paper highlights the importance of integrating social and technical approach (which is so called a “hybrid socio-technical approach") as one innovative and strategic program to support the social development in geodisaster prone area in Indonesia. Such program mainly based on public education and community participation as a partnership program by the University, local government and may also with the private company and/ or local NGO. The indigenous, simple and low cost technology has also been introduced and developed as a part of the hybrid sociotechnical system, in order to ensure the life and environmental protection, with respect to the sustainable human and social development.
Abstract: The purpose of the study reported here was designing Information Dissemination System (IDS) based E-learning in agricultural of Iran. A questionnaire was developed to designing Information Dissemination System. The questionnaire was distributed to 96 extension agents who work for Management of Extension and Farming System of Khuzestan province of Iran. Data collected were analyzed using the Statistical Package for the Social Sciences (SPSS). Appropriate statistical procedures for description (frequencies, percent, means, and standard deviations) were used. In this study there was a significant relationship between the age , IT skill and knowledge, years of extension work, the extend of information seeking motivation, level of job satisfaction and level of education with use of information technology by extension agent. According to extension agents five factors were ranked respectively as five top essential items to designing Information Dissemination System (IDS) based E-learning in agricultural of Iran. These factors include: 1) Establish communication between farmers, coordinators (extension agents), agricultural experts, research centers, and community by information technology. 2) The communication between all should be mutual. 3) The information must be based farmers need. 4) Internet used as a facility to transfer the advanced agricultural information to the farming community. 5) Farmers can be illiterate and speak a local and they are not expected to use the system directly. Knowledge produced by the agricultural scientist must be transformed in to computer understandable presentation. To designing Information Dissemination System, electronic communication, in the agricultural society and rural areas must be developed. This communication must be mutual between all factors.
Abstract: Teachers form the backbone of any educational system, hence selecting qualified candidates is very crucial. In Malaysia, the decision making in the selection process involves a few stages: Initial filtering through academic achievement, taking entry examination and going through an interview session. The last stage is the most challenging since it highly depends on human judgment. Therefore, this study sought to identify the selection criteria for teacher candidates that form the basis for an efficient multi-criteria teacher-candidate selection model for that last stage. The relevant criteria were determined from the literature and also based on expert input that is those who were involved in interviewing teacher candidates from a public university offering the formal training program. There are three main competency criteria that were identified which are content of knowledge, communication skills and personality. Further, each main criterion was divided into a few subcriteria. The Analytical Hierarchy Process (AHP) technique was employed to allocate weights for the criteria and later, integrated a Simple Weighted Average (SWA) scoring approach to develop the selection model. Subsequently, a web-based Decision Support System was developed to assist in the process of selecting the qualified teacher candidates. The Teacher-Candidate Selection (TeCaS) system is able to assist the panel of interviewers during the selection process which involves a large amount of complex qualitative judgments.
Abstract: The aim of research project is to evaluate quantity and
quality for conjunctive use of groundwater and surface water in lower
in the Lower Nam Kam area, Thailand, even though there have been
hints of saline soil and water. The mathematical model named
WUSMO and MIKE Basin were applied for the calculation of crop
water utilization. Results of the study showed that, in irrigation
command area, water consumption rely on various sources; rain water
21.56%, irrigation water 78.29%, groundwater and some small surface
storage 0.15%. Meanwhile, for non-irrigation command area, water
consumption depends on the Nam Kam and Nambang stream 42%,
rain water 36.75% and groundwater and some small surface storage
19.18%. Samples of surface water and groundwater were collected for
2 seasons. The criterion was determined for the assessment of suitable
water for irrigation. It was found that this area has very limited sources
of suitable water for irrigation.
Abstract: The Boundary Representation of a 3D manifold contains
FACES (connected subsets of a parametric surface S : R2 -!
R3). In many science and engineering applications it is cumbersome
and algebraically difficult to deal with the polynomial set and
constraints (LOOPs) representing the FACE. Because of this reason, a
Piecewise Linear (PL) approximation of the FACE is needed, which is
usually represented in terms of triangles (i.e. 2-simplices). Solving the
problem of FACE triangulation requires producing quality triangles
which are: (i) independent of the arguments of S, (ii) sensitive to the
local curvatures, and (iii) compliant with the boundaries of the FACE
and (iv) topologically compatible with the triangles of the neighboring
FACEs. In the existing literature there are no guarantees for the point
(iii). This article contributes to the topic of triangulations conforming
to the boundaries of the FACE by applying the concept of parameterindependent
Gabriel complex, which improves the correctness of the
triangulation regarding aspects (iii) and (iv). In addition, the article
applies the geometric concept of tangent ball to a surface at a point to
address points (i) and (ii). Additional research is needed in algorithms
that (i) take advantage of the concepts presented in the heuristic
algorithm proposed and (ii) can be proved correct.
Abstract: In this paper, a two factor scheme is proposed to
generate cryptographic keys directly from biometric data, which
unlike passwords, are strongly bound to the user. Hash value of the
reference iris code is used as a cryptographic key and its length
depends only on the hash function, being independent of any other
parameter. The entropy of such keys is 94 bits, which is much higher
than any other comparable system. The most important and distinct
feature of this scheme is that it regenerates the reference iris code by
providing a genuine iris sample and the correct user password. Since
iris codes obtained from two images of the same eye are not exactly
the same, error correcting codes (Hadamard code and Reed-Solomon
code) are used to deal with the variability. The scheme proposed here
can be used to provide keys for a cryptographic system and/or for
user authentication. The performance of this system is evaluated on
two publicly available databases for iris biometrics namely CBS and
ICE databases. The operating point of the system (values of False
Acceptance Rate (FAR) and False Rejection Rate (FRR)) can be set
by properly selecting the error correction capacity (ts) of the Reed-
Solomon codes, e.g., on the ICE database, at ts = 15, FAR is 0.096%
and FRR is 0.76%.
Abstract: Video watermarking is usually considered as watermarking of a set of still images. In frame-by-frame watermarking approach, each video frame is seen as a single watermarked image, so collusion attack is more critical in video watermarking. If the same or redundant watermark is used for embedding in every frame of video, the watermark can be estimated and then removed by watermark estimate remodolulation (WER) attack. Also if uncorrelated watermarks are used for every frame, these watermarks can be washed out with frame temporal filtering (FTF). Switching watermark system or so-called SS-N system has better performance against WER and FTF attacks. In this system, for each frame, the watermark is randomly picked up from a finite pool of watermark patterns. At first SS-N system will be surveyed and then a new collusion attack for SS-N system will be proposed using a new algorithm for separating video frame based on watermark pattern. So N sets will be built in which every set contains frames carrying the same watermark. After that, using WER attack in every set, N different watermark patterns will be estimated and removed later.
Abstract: Until recently, energy security and climate change
were considered separate issues to be dealt with by policymakers.
The two issues are now converging, challenging the security and
climate communities to develop a better understanding of how to deal
with both issues simultaneously. Although Egypt is not a major
contributor to the world's total GHG emissions, it is particularly
vulnerable to the potential effects of global climate change such as
rising sea levels and changed patterns of rainfall in the Nile Basin.
Climate change is a major threat to sustainable growth and
development in Egypt, and the achievement of the Millennium
Development Goals. Egypt-s capacity to respond to the challenges of
climate instability will be expanded by improving overall resilience,
integrating climate change goals into sustainable development
strategies, increasing the use of modern energy systems with reduced
carbon intensity, and strengthening international initiatives. This
study seeks to establish a framework for considering the complex and
evolving links between energy security and climate change,
applicable to Egypt.
Abstract: This paper proposes a new algebraic scheme to design a PID controller for higher order linear time invariant continuous systems. Modified PSO (MPSO) based model order formulation techniques have applied to obtain the effective formulated second order system. A controller is tuned to meet the desired performance specification by using pole-zero cancellation method. Proposed PID controller is attached with both higher order system and formulated second order system. The closed loop response is observed for stabilization process and compared with general PSO based formulated second order system. The proposed method is illustrated through numerical example from literature.
Abstract: Cybercrime is now becoming a big challenge in Nigeria apart from the traditional crime. Inability to identify perpetrators is one of the reasons for the growing menace. This paper proposes a design for monitoring internet users’ activities in order to curbing cybercrime. It requires redefining the operations of Internet Service Providers (ISPs) which will now mandate users to be authenticated before accessing the internet. In implementing this work which can be adapted to a larger scale, a virtual router application is developed and configured to mimic a real router device. A sign-up portal is developed to allow users to register with the ISP. The portal asks for identification information which will include bio-data and government issued identification data like National Identity Card number, et cetera. A unique username and password are chosen by the user to enable access to the internet which will be used to reference him to an Internet Protocol Address (IP Address) of any system he uses on the internet and thereby associating him to any criminal act related to that IP address at that particular time. Questions such as “What happen when another user knows the password and uses it to commit crime?” and other pertinent issues are addressed.
Abstract: Nowadays wireless technology plays an important
role in public and personal communication. However, the growth of
wireless networking has confused the traditional boundaries between
trusted and untrusted networks. Wireless networks are subject to a
variety of threats and attacks at present. An attacker has the ability to
listen to all network traffic which becoming a potential intrusion.
Intrusion of any kind may lead to a chaotic condition. In addition,
improperly configured access points also contribute the risk to
wireless network. To overcome this issue, a security solution that
includes an intrusion detection and prevention system need to be
implemented. In this paper, first the security drawbacks of wireless
network will be analyzed then investigate the characteristics and also
the limitations on current wireless intrusion detection and prevention
system. Finally, the requirement of next wireless intrusion prevention
system will be identified including some key issues which should be
focused on in the future to overcomes those limitations.
Abstract: The optimal bisection width of r-dimensional N×
· · ·× N grid is known to be Nr-1 when N is even, but when
N is odd, only approximate values are available. This paper
shows that the exact bisection width of grid is Nr
-1
N-1 when N is odd.
Abstract: Automatic reading of handwritten cheque is a computationally
complex process and it plays an important role in financial
risk management. Machine vision and learning provide a viable
solution to this problem. Research effort has mostly been focused
on recognizing diverse pitches of cheques and demand drafts with an
identical outline. However most of these methods employ templatematching
to localize the pitches and such schemes could potentially
fail when applied to different types of outline maintained by the
bank. In this paper, the so-called outline problem is resolved by
a cheque information tree (CIT), which generalizes the localizing
method to extract active-region-of-entities. In addition, the weight
based density plot (WBDP) is performed to isolate text entities and
read complete pitches. Recognition is based on texture features using
neural classifiers. Legal amount is subsequently recognized by both
texture and perceptual features. A post-processing phase is invoked
to detect the incorrect readings by Type-2 grammar using the Turing
machine. The performance of the proposed system was evaluated
using cheque and demand drafts of 22 different banks. The test data
consists of a collection of 1540 leafs obtained from 10 different
account holders from each bank. Results show that this approach
can easily be deployed without significant design amendments.
Abstract: Analytical seismic response of multi-story building
supported on base isolation system is investigated under real
earthquake motion. The superstructure is idealized as a shear type
flexible building with lateral degree-of-freedom at each floor. The
force-deformation behaviour of the isolation system is modelled by
the bi-linear behaviour which can be effectively used to model all
isolation systems in practice. The governing equations of motion of
the isolated structural system are derived. The response of the system
is obtained numerically by step-by-method under three real recorded
earthquake motions and pulse motions associated in the near-fault
earthquake motion. The variation of the top floor acceleration, interstory
drift, base shear and bearing displacement of the isolated
building is studied under different initial stiffness of the bi-linear
isolation system. It was observed that the high initial stiffness of the
isolation system excites higher modes in base-isolated structure and
generate floor accelerations and story drift. Such behaviour of the
base-isolated building especially supported on sliding type of
isolation systems can be detrimental to sensitive equipment installed
in the building. On the other hand, the bearing displacement and base
shear found to reduce marginally with the increase of the initial
stiffness of the initial stiffness of the isolation system. Further, the
above behaviour of the base-isolated building was observed for
different parameters of the bearing (i.e. post-yield stiffness and
characteristic strength) and earthquake motions (i.e. real time history
as well as pulse type motion).