Abstract: This paper describes the design of a voltage based maximum power point tracker (MPPT) for photovoltaic (PV) applications. Of the various MPPT methods, the voltage based method is considered to be the simplest and cost effective. The major disadvantage of this method is that the PV array is disconnected from the load for the sampling of its open circuit voltage, which inevitably results in power loss. Another disadvantage, in case of rapid irradiance variation, is that if the duration between two successive samplings, called the sampling period, is too long there is a considerable loss. This is because the output voltage of the PV array follows the unchanged reference during one sampling period. Once a maximum power point (MPP) is tracked and a change in irradiation occurs between two successive samplings, then the new MPP is not tracked until the next sampling of the PV array voltage. This paper proposes an MPPT circuit in which the sampling interval of the PV array voltage, and the sampling period have been shortened. The sample and hold circuit has also been simplified. The proposed circuit does not utilize a microcontroller or a digital signal processor and is thus suitable for low cost and low power applications.
Abstract: This paper presents part of a research into the small
scale modelling of masonry. Small scale testing of masonry has been
carried out by many authors, but few have attempted a systematic
determination of the parameters that affect masonry at a small scale.
The effect of increasing mortar strength and different sand gradings
under compression were investigated. The results show masonry
strength at small scale is influenced by increasing mortar strength and
different sand gradings.
Abstract: Polymer melt compressibility and mold surface roughness, which are generally ignored during the filling stage of the conventional injection molding, may become increasingly significant in micro injection molding where the parts become smaller. By employing the 2.5D generalized Hele-Shaw model, we presented here the effects of polymer compressibility and mold surface roughness on mold-filling in a micro-thickness cavity. To elucidate the effects of surface roughness, numerical investigations were conducted using a cavity flat plate which has two halves with different surface roughness. This allows the comparison of flow field on two different halves under identical processing conditions but with different roughness. Results show that polymer compressibility and mold surface roughness have effects on mold filling in micro injection molding. There is in shrinkage reduction as the density is increased due to polymer melt compressibility during the filling stage.
Abstract: A study has been carried out to determine the effect of
coating two commercial glass-ionomer cements in either petroleum
jelly or wax. After coating, specimens were stored in water for 24 or
168 hours, then the coating removed and the surface examined.
Coating in wax was found to increase the surface hardness
significantly compared with the uncoated control, whereas coating
the specimens in petroleum jelly led to only a slight increase in
surface hardness. Coating in wax led to no detectable ion release
after either 24 or 168 hours, though there was some ion release after
the coating had been removed and the specimens exposed to water
for a further 24 hours. This shows that soluble species remained in
these specimens. Overall, this study confirms the idea that immature
glass-ionomers should be protected from early exposure to moisture,
and that the protection offered by petroleum jelly is only modest.
Abstract: Small signal stability causes small perturbations in the
generator that can cause instability in the power network. It is
generally known that small signal stability are directly related to the
generator and load properties. This paper examines the effects of
generator input variations on power system oscillations for a small
signal stability study. Eigenvaules and eigenvectors are used to
examine the stability of the power system. The dynamic power
system's mathematical model is constructed and thus calculated using
load flow and small signal stability toolbox on MATLAB. The power
system model is based on a 3-machine 9-bus system that was
modified to suit this study. In this paper, Participation Factors are a
means to gauge the effects of variation in generation with other
parameters on the network are also incorporated.
Abstract: In this paper we present a novel design of a wearable
electronic textile. After defining a special application, we used the
specifications of some low power, tiny elements including sensors,
microcontrollers, transceivers, and a fault tolerant special topology to
have the most reliability as well as low power consumption and
longer lifetime. We have considered two different conditions as
normal and bodily critical conditions and set priorities for using
different sensors in various conditions to have a longer effective
lifetime.
Abstract: Software testability is proposed to address the problem of increasing cost of test and the quality of software. Testability measure provides a quantified way to denote the testability of software. Since 1990s, many testability measure models are proposed to address the problem. By discussing the contradiction between domain testability and domain range ratio (DRR), a new testability measure, semantic fault distance, is proposed. Its validity is discussed.
Abstract: Due to the call of global warming effects, city planners aim at actions for reducing carbon emission. One of the approaches is to promote the usage of public transportation system toward the transit-oriented-development. For example, rapid transit system in Taipei city and Kaohsiung city are opening. However, until November 2008 the average daily patronage counted only 113,774 passengers at Kaohsiung MRT systems, much less than which was expected. Now the crucial questions: how the public transport competes with private transport? And more importantly, what factors would enhance the use of public transport? To give the answers to those questions, our study first applied regression to analyze the factors attracting people to use public transport around cities in the world. It is shown in our study that the number of MRT stations, city population, cost of living, transit fare, density, gasoline price, and scooter being a major mode of transport are the major factors. Subsequently, our study identified successful and unsuccessful cities in regard of the public transport usage based on the diagnosis of regression residuals. Finally, by comparing transportation strategies adopted by those successful cities, our conclusion stated that Kaohsiung City could apply strategies such as increasing parking fees, reducing parking spaces in downtown area, and reducing transfer time by providing more bus services and public bikes to promote the usage of public transport.
Abstract: Internet is largely composed of textual contents and a
huge volume of digital contents gets floated over the Internet daily.
The ease of information sharing and re-production has made it
difficult to preserve author-s copyright. Digital watermarking came
up as a solution for copyright protection of plain text problem after
1993. In this paper, we propose a zero text watermarking algorithm
based on occurrence frequency of non-vowel ASCII characters and
words for copyright protection of plain text. The embedding
algorithm makes use of frequency non-vowel ASCII characters and
words to generate a specialized author key. The extraction algorithm
uses this key to extract watermark, hence identify the original
copyright owner. Experimental results illustrate the effectiveness of
the proposed algorithm on text encountering meaning preserving
attacks performed by five independent attackers.
Abstract: This paper presents a studyof the impact of reference
node locations on the accuracy of the indoor positioning systems. In
particular, we analyze the localization accuracy of the RSSI database
mapping techniques, deploying on the IEEE 802.15.4 wireless
networks. The results show that the locations of the reference nodes
used in the positioning systems affect the signal propagation
characteristics in the service area. Thisin turn affects the accuracy of the wireless indoor positioning system. We found that suitable
location of reference nodes could reduce the positioning error upto 35 %.
Abstract: In this paper we intend to ascertain the state of the art on multifingered end-effectors, also known as robotic hands or dexterous robot hands, and propose an experimental setup for an innovative task based design approach, involving cutting edge technologies in motion capture. After an initial description of the capabilities and complexity of a human hand when grasping objects, in order to point out the importance of replicating it, we analyze the mechanical and kinematical structure of some important works carried out all around the world in the last three decades and also review the actuators and sensing technologies used. Finally we describe a new design philosophy proposing an experimental setup for the first stage using recent developments in human body motion capture systems that might lead to lighter and always more dexterous robotic hands.
Abstract: The design of high-rise building is more often dictated
by its serviceability rather than strength. Structural Engineers are
always striving to overcome challenge of controlling lateral
deflection and storey drifts as well as self weight of structure
imposed on foundation.
One of the most effective techniques is the use of outrigger and
belt truss system in Composite structures that can astutely solve the
above two issues in High-rise constructions.
This paper investigates deflection control by effective utilisation
of belt truss and outrigger system on a 60-storey composite building
subjected to wind loads. A three dimensional Finite Element Analysis
is performed with one, two and three outrigger levels. The reductions
in lateral deflection are 34%, 42% and 51% respectively as compared
to a model without any outrigger system. There is an appreciable
decline in the storey drifts with the introduction of these stiffer
arrangements.
Abstract: The accuracy of estimated stability and control
derivatives of a light aircraft from flight test data were evaluated. The light aircraft, named ChangGong-91, is the first certified aircraft from
the Korean government. The output error method, which is a maximum likelihood estimation technique and considers measurement
noise only, was used to analyze the aircraft responses measures. The
multi-step control inputs were applied in order to excite the short period mode for the longitudinal and Dutch-roll mode for the lateral-directional motion. The estimated stability/control derivatives of Chan Gong-91 were analyzed for the assessment of handling
qualities comparing them with those of similar aircraft. The accuracy of the flight derivative estimates derived from flight test measurement
was examined in engineering judgment, scatter and Cramer-Rao bound, which turned out to be satisfactory with minor defects..
Abstract: In hypersonic environments, the aerothermal effect
makes it difficult for the optical side windows of optical guided
missiles to withstand high heat. This produces cracking or breaking,
resulting in an inability to function. This study used computational
fluid mechanics to investigate the external cooling jet conditions of
optical side windows. The turbulent models k-ε and k-ω were
simulated. To be in better accord with actual aerothermal
environments, a thermal radiation model was added to examine
suitable amounts of external coolants and the optical window
problems of aero-thermodynamics. The simulation results indicate that
when there are no external cooling jets, because airflow on the optical
window and the tail groove produce vortices, the temperatures in these
two locations reach a peak of approximately 1600 K. When the
external cooling jets worked at 0.15 kg/s, the surface temperature of
the optical windows dropped to approximately 280 K. When adding
thermal radiation conditions, because heat flux dissipation was faster,
the surface temperature of the optical windows fell from 280 K to
approximately 260 K. The difference in influence of the different
turbulence models k-ε and k-ω on optical window surface temperature
was not significant.
Abstract: Expression and secretion of inflammation markers are
disturbed in obesity. Interleukin-6 reduces body fat mass. The
common G-174C polymorphism in the promoter of IL-6 gene has
been reported that effects on transcriptional regulation. The objective
was to investigate association of the common polymorphism G-174C
with obesity in Iranian population. The present study is cross
sectional association study that included 242 individuals (110 men
and 132 women). Serum IL-6 levels, C-reactive protein, fasting
blood glucose and blood lipids profile were measured .BMI and
WHR were calculated. Genotyping is carried out by PCR and RFLP.
The frequencies of G and C allele were 64.5% and 35.5%,
respectively. The G-174C polymorphism was not associated with
BMI and WHR. However in obese individual, fasting blood glucose
was significantly higher in carrier of C allele compared with the noncarrier.
The IL-6 G-174C polymorphism is not a risk factor for
obesity in Iranian population.
Abstract: The mobile users with Laptops need to have an
efficient access to i.e. their home personal data or to the Internet from
any place in the world, regardless of their location or point of
attachment, especially while roaming outside the home subnet. An
efficient interpretation of packet losses problem that is encountered
from this roaming is to the centric of all aspects in this work, to be
over-highlighted. The main previous works, such as BER-systems,
Amigos, and ns-2 implementation that are considered to be in
conjunction with that problem under study are reviewed and
discussed. Their drawbacks and limitations, of stopping only at
monitoring, and not to provide an actual solution for eliminating or
even restricting these losses, are mentioned. Besides that, the
framework around which we built a Triple-R sequence as a costeffective
solution to eliminate the packet losses and bridge the gap
between subnets, an area that until now has been largely neglected, is
presented. The results show that, in addition to the high bit error rate
of wireless mobile networks, mainly the low efficiency of mobile-IP
registration procedure is a direct cause of these packet losses.
Furthermore, the output of packet losses interpretation resulted an
illustrated triangle of the registration process. This triangle should be
further researched and analyzed in our future work.
Abstract: The effect of the blade tip geometry of a high pressure
gas turbine is studied experimentally and computationally for high
speed leakage flows. For this purpose two simplified models are
constructed, one models a flat tip of the blade and the second models
a cavity tip of the blade. Experimental results are obtained from a
transonic wind tunnel to show the static pressure distribution along
the tip wall and provide flow visualization. RANS computations
were carried to provide further insight into the mean flow behavior
and to calculate the discharge coefficient which is a measure of the
flow leaking over the tip. It is shown that in both geometries of tip
the flow separates over the tip to form a separation bubble. The
bubble is higher for the cavity tip while a complete shock wave
system of oblique waves ending with a normal wave can be seen for
the flat tip. The discharge coefficient for the flat tip shows less
dependence on the pressure ratio over the blade tip than the cavity
tip. However, the discharge coefficient for the cavity tip is lower than
that of the flat tip, showing a better ability to reduce the leakage flow
and thus increase the turbine efficiency.
Abstract: This paper presents an adaptive feedback linearization approach to derive helicopter. Ideal feedback linearization is defined for the cases when the system model is known. Adaptive feedback linearization is employed to get asymptotically exact cancellation for the inherent uncertainty in the knowledge of the given parameters of system. The control algorithm is implemented using the feedback linearization technique and adaptive method. The controller parameters are unknown where an adaptive control law aims to drive them towards their ideal values for providing perfect model matching between the reference model and the closed-loop plant model. The converged parameters of controller would then provide good estimates for the unknown plant parameters.
Abstract: This experiment discusses the effects of fracture
parameters such as depth, length, width, angle and the number of the
fracture to the conductance properties of laterite using the DUK-2B
digital electrical measurement system combined with the method of
simulating the fractures. The results of experiment show that the
changes of fracture parameters produce effects to the conductance
properties of laterite. There is a clear degressive period of the
conductivity of laterite during increasing the depth, length, width, or
the angle and the quantity of fracture gradually. When the depth of
fracture exceeds the half thickness of the soil body, the conductivity of
laterite shows evidently non-linear diminishing pattern and the
amplitude of decrease tends to increase. The length of fracture has
fewer effects than the depth to the conductivity. When the width of
fracture reaches some fixed values, the change of the conductivity is
less sensitive to the change of the width, and at this time, the
conductivity of laterite maintains at a stable level. When the angle of
fracture is less than 45°, the decrease of the conductivity is more
clearly as the angle increases. But when angle is more than 45°,
change of the conductivity is relatively gentle as the angle increases.
The increasing quantity of the fracture causes the other fracture
parameters having great impact on the change of conductivity. When
moisture content and temperature were unchanged, depth and angle of
fractures are the major factors affecting the conductivity of laterite
soil; quantity, length, and width are minor influencing factors. The
sensitivity of fracture parameters affect conductivity of laterite soil is:
depth >angles >quantity >length >width.
Abstract: In the current Grid environment, efficient workload
management presents a significant challenge, for which there are
exorbitant de facto standards encompassing resource discovery,
brokerage, and data transfer, among others. In addition, the real-time
resource status, essential for an optimal resource allocation strategy,
is often not readily accessible. To address these issues and provide a
cleaner abstraction of the Grid with the potential of generalizing into
arbitrary resource-sharing environment, this paper proposes a new
Condor-based pilot mechanism applied in the PanDA architecture,
PanDA-PF WMS, with the goal of providing a more generic yet
efficient resource allocating strategy. In this architecture, the PanDA
server primarily acts as a repository of user jobs, responding to pilot
requests from distributed, remote resources. Scheduling decisions are
subsequently made according to the real-time resource information
reported by pilots. Pilot Factory is a Condor-inspired solution for a
scalable pilot dissemination and effectively functions as a resource
provisioning mechanism through which the user-job server, PanDA,
reaches out to the candidate resources only on demand.