Abstract: SAD (Sum of Absolute Difference) algorithm is
heavily used in motion estimation which is computationally highly
demanding process in motion picture encoding. To enhance the
performance of motion picture encoding on a VLIW processor, an
efficient implementation of SAD algorithm on the VLIW processor is
essential. SAD algorithm is programmed as a nested loop with a
conditional branch. In VLIW processors, loop is usually optimized by
software pipelining, but researches on optimal scheduling of software
pipelining for nested loops, especially nested loops with conditional
branches are rare. In this paper, we propose an optimal scheduling and
implementation of SAD algorithm with conditional branch on a VLIW
DSP processor. The proposed optimal scheduling first transforms the
nested loop with conditional branch into a single loop with conditional
branch with consideration of full utilization of ILP capability of the
VLIW processor and realization of earlier escape from the loop. Next,
the proposed optimal scheduling applies a modulo scheduling
technique developed for single loop. Based on this optimal scheduling
strategy, optimal implementation of SAD algorithm on TMS320C67x,
a VLIW DSP is presented. Through experiments on TMS320C6713
DSK, it is shown that H.263 encoder with the proposed SAD
implementation performs better than other H.263 encoder with other
SAD implementations, and that the code size of the optimal SAD
implementation is small enough to be appropriate for embedded
environments.
Abstract: A numerical investigation has carried out to understand the melting characteristics of phase change material (PCM) in a fin type latent heat storage with the addition of embedded aluminum spiral fillers. It is known that melting performance of PCM can be significantly improved by increasing the number of embedded metallic fins in the latent heat storage system but to certain values where only lead to small improvement in heat transfer rate. Hence, adding aluminum spiral fillers within the fin gap can be an option to improve heat transfer internally. This paper presents extensive computational visualizations on the PCM melting patterns of the proposed fin-spiral fillers configuration. The aim of this investigation is to understand the PCM-s melting behaviors by observing the natural convection currents movement and melting fronts formation. Fluent 6.3 simulation software was utilized in producing twodimensional visualizations of melting fractions, temperature distributions and flow fields to illustrate the melting process internally. The results show that adding aluminum spiral fillers in Fin type latent heat storage can promoted small but more active natural convection currents and improve melting of PCM.
Abstract: The aim of this research is to develop a fast and
reliable surveillance system based on a personal digital assistant
(PDA) device. This is to extend the capability of the device to detect
moving objects which is already available in personal computers.
Secondly, to compare the performance between Background
subtraction (BS) and Temporal Frame Differencing (TFD) techniques
for PDA platform as to which is more suitable. In order to reduce
noise and to prepare frames for the moving object detection part,
each frame is first converted to a gray-scale representation and then
smoothed using a Gaussian low pass filter. Two moving object
detection schemes i.e., BS and TFD have been analyzed. The
background frame is updated by using Infinite Impulse Response
(IIR) filter so that the background frame is adapted to the varying
illuminate conditions and geometry settings. In order to reduce the
effect of noise pixels resulting from frame differencing
morphological filters erosion and dilation are applied. In this
research, it has been found that TFD technique is more suitable for
motion detection purpose than the BS in term of speed. On average
TFD is approximately 170 ms faster than the BS technique
Abstract: The purpose of this paper is to investigate the
influence of a number of variables on the conditional mean and
conditional variance of credit spread changes. The empirical analysis
in this paper is conducted within the context of bivariate GARCH-in-
Mean models, using the so-called BEKK parameterization. We show
that credit spread changes are determined by interest-rate and equityreturn
variables, which is in line with theory as provided by the
structural models of default. We also identify the credit spread
change volatility as an important determinant of credit spread
changes, and provide evidence on the transmission of volatility
between the variables under study.
Abstract: Brain Computer Interface (BCI) has been recently
increased in research. Functional Near Infrared Spectroscope (fNIRs)
is one the latest technologies which utilize light in the near-infrared
range to determine brain activities. Because near infrared technology
allows design of safe, portable, wearable, non-invasive and wireless
qualities monitoring systems, fNIRs monitoring of brain
hemodynamics can be value in helping to understand brain tasks. In
this paper, we present results of fNIRs signal analysis indicating that
there exist distinct patterns of hemodynamic responses which
recognize brain tasks toward developing a BCI. We applied two
different mathematics tools separately, Wavelets analysis for
preprocessing as signal filters and feature extractions and Neural
networks for cognition brain tasks as a classification module. We
also discuss and compare with other methods while our proposals
perform better with an average accuracy of 99.9% for classification.
Abstract: Let Gα ,β (γ ,δ ) denote the class of function
f (z), f (0) = f ′(0)−1= 0 which satisfied e δ {αf ′(z)+ βzf ′′(z)}> γ i Re
in the open unit disk D = {z ∈ı : z < 1} for some α ∈ı (α ≠ 0) ,
β ∈ı and γ ∈ı (0 ≤γ 0 . In
this paper, we determine some extremal properties including
distortion theorem and argument of f ′( z ) .
Abstract: This paper represents an investigation on how exploiting multiple transmit antennas by OFDM based wireless LAN subscribers can mitigate physical layer error rate. Then by comparing the Wireless LANs that utilize spatial diversity techniques with the conventional ones it will reveal how PHY and TCP throughputs behaviors are ameliorated. In the next step it will assess the same issues based on a cellular context operation which is mainly introduced as an innovated solution that beside a multi cell operation scenario benefits spatio-temporal signaling schemes as well. Presented simulations will shed light on the improved performance of the wide range and high quality wireless LAN services provided by the proposed approach.
Abstract: Building life cycle will never be excused from the existence of defects and deterioration. They are common problems in building, existed in newly build or in aged building. Buildings constructed from wood are indeed affected by its agent and serious defects and damages can reduce values to a building. In repair works, it is important to identify the causes and repair techniques that best suites with the condition. This paper reviews the conservation of traditional timber mosque in Malaysia comprises the concept, principles and approaches of mosque conservation in general. As in conservation practice, wood in historic building can be conserved by using various restoration and conservation techniques which this can be grouped as Fully and Partial Replacement, Mechanical Reinforcement, Consolidation by Impregnation and Reinforcement, Removing Paint and also Preservation of Wood and Control Insect Invasion, as to prolong and extended the function of a timber in a building. It resulted that the common techniques adopted in timber mosque conservation are from the conventional ways and the understanding of the repair technique requires the use of only preserve wood to prevent the future immature defects.
Abstract: Building maintenance plays an important role among other activities in building operation. Building defect and damages are part of the building maintenance 'bread and butter' as their input indicated in the building inspection is very much justified, particularly as to determine the building performance. There will be no escape route or short cut from building maintenance work. This study attempts to identify a competitive performance that translates the Critical Success Factor achievements and satisfactorily meet the university-s expectation. The quality and efficiency of maintenance management operation of building depends, to some extent, on the building condition information, the expectation from the university sector and the works carried out for each maintenance activity. This paper reviews the critical success factor in building maintenance management practice for university sectors from four (4) perspectives which include (1) customer (2) internal processes (3) financial and (4) learning and growth perspective. The enhancement of these perspectives is capable to reach the maintenance management goal for a better living environment in university campus.
Abstract: Traditional wind tunnel models are meticulously machined from metal in a process that can take several months. While very precise, the manufacturing process is too slow to assess a new design's feasibility quickly. Rapid prototyping technology makes this concurrent study of air vehicle concepts via computer simulation and in the wind tunnel possible. This paper described the Affects layer thickness models product with rapid prototyping on Aerodynamic Coefficients for Constructed wind tunnel testing models. Three models were evaluated. The first model was a 0.05mm layer thickness and Horizontal plane 0.1μm (Ra) second model was a 0.125mm layer thickness and Horizontal plane 0.22μm (Ra) third model was a 0.15mm layer thickness and Horizontal plane 4.6μm (Ra). These models were fabricated from somos 18420 by a stereolithography (SLA). A wing-body-tail configuration was chosen for the actual study. Testing covered the Mach range of Mach 0.3 to Mach 0.9 at an angle-of-attack range of -2° to +12° at zero sideslip. Coefficients of normal force, axial force, pitching moment, and lift over drag are shown at each of these Mach numbers. Results from this study show that layer thickness does have an effect on the aerodynamic characteristics in general; the data differ between the three models by fewer than 5%. The layer thickness does have more effect on the aerodynamic characteristics when Mach number is decreased and had most effect on the aerodynamic characteristics of axial force and its derivative coefficients.
Abstract: The results from experimental research of deformation
by upsetting and die forging of lead specimens wit controlled impact
are presented. Laboratory setup for conducting the investigations,
which uses cold rocket engine operated with compressed air, is
described. The results show that when using controlled impact is
achieving greater plastic deformation and consumes less impact
energy than at ordinary impact deformation process.
Abstract: The simulation of extrusion process is studied widely
in order to both increase products and improve quality, with broad
application in wire coating. The annular tube-tooling extrusion was
set up by a model that is termed as Navier-Stokes equation in
addition to a rheological model of differential form based on singlemode
exponential Phan-Thien/Tanner constitutive equation in a twodimensional
cylindrical coordinate system for predicting the
contraction point of the polymer melt beyond the die. Numerical
solutions are sought through semi-implicit Taylor-Galerkin pressurecorrection
finite element scheme. The investigation was focused on
incompressible creeping flow with long relaxation time in terms of
Weissenberg numbers up to 200. The isothermal case was considered
with surface tension effect on free surface in extrudate flow and no
slip at die wall. The Stream Line Upwind Petrov-Galerkin has been
proposed to stabilize solution. The structure of mesh after die exit
was adjusted following prediction of both top and bottom free
surfaces so as to keep the location of contraction point around one
unit length which is close to experimental results. The simulation of
extrusion process is studied widely in order to both increase products
and improve quality, with broad application in wire coating. The
annular tube-tooling extrusion was set up by a model that is termed
as Navier-Stokes equation in addition to a rheological model of
differential form based on single-mode exponential Phan-
Thien/Tanner constitutive equation in a two-dimensional cylindrical
coordinate system for predicting the contraction point of the polymer
melt beyond the die. Numerical solutions are sought through semiimplicit
Taylor-Galerkin pressure-correction finite element scheme.
The investigation was focused on incompressible creeping flow with
long relaxation time in terms of Weissenberg numbers up to 200. The
isothermal case was considered with surface tension effect on free
surface in extrudate flow and no slip at die wall. The Stream Line
Upwind Petrov-Galerkin has been proposed to stabilize solution. The
structure of mesh after die exit was adjusted following prediction of
both top and bottom free surfaces so as to keep the location of
contraction point around one unit length which is close to
experimental results.
Abstract: This paper studies the optimum design for reducing
optical loss of an 8x8 mechanical type optical switch due to the
temperature change. The 8x8 optical switch is composed of a base, 8
input fibers, 8 output fibers, 3 fixed mirrors and 17 movable mirrors.
First, an innovative switch configuration is proposed with
thermal-compensated design. Most mechanical type optical switches
have a disadvantage that their precision and accuracy are influenced
by the ambient temperature. Therefore, the thermal-compensated
design is to deal with this situation by using materials with different
thermal expansion coefficients (α). Second, a parametric modeling
program is developed to generate solid models for finite element
analysis, and the thermal and structural behaviors of the switch are
analyzed. Finally, an integrated optimum design program, combining
Autodesk Inventor Professional software, finite element analysis
software, and genetic algorithms, is developed for improving the
thermal behaviors that the optical loss of the switch is reduced. By
changing design parameters of the switch in the integrated design
program, the final optimum design that satisfies the design constraints
and specifications can be found.
Abstract: Place is a where dimension formed by people-s
relationship with physical settings, individual and group activities,
and meanings. 'Place Attachment', 'Place Identity'and 'Sense of
Place' are some concepts that could describe the quality of people-s
relationships with a place. The concept of Sense of place is used in
studying human-place bonding, attachment and place meaning. Sense
of Place usually is defined as an overarching impression
encompassing the general ways in which people feel about places,
senses it, and assign concepts and values to it. Sense of place is
highlighted in this article as one of the prevailing concepts among
place-based researches. Considering dimensions of sense of place has
always been beneficial for investigating public place attachment and
pro-environmental attitudes towards these places. The creation or
preservation of Sense of place is important in maintaining the quality
of the environment as well as the integrity of human life within it.
While many scholars argued that sense of place is a vague concept,
this paper will summarize and analyze the existing seminal literature.
Therefore, in this paper first the concept of Sense of place and its
characteristics will be examined afterward the scales of Sense of
place will be reviewed and the factors that contribute to form Sense
of place will be evaluated and finally Place Attachment as an
objective dimension for measuring the sense of place will be
described.
Abstract: In this paper we have suggested a new system for egovernment.
In this method a government can design a precise and
perfect system to control people and organizations by using five
major documents. These documents contain the important
information of each member of a society and help all organizations to
do their informatics tasks through them. This information would be
available by only a national code and a secure program would
support it. The suggested system can give a good awareness to the
society and help it be managed correctly.
Abstract: This research contribution propels the idea of collaborating environment for the execution of student satellite projects in the backdrop of project management principles. The recent past has witnessed a technological shift in the aerospace industry from the big satellite projects to the small spacecrafts especially for the earth observation and communication purposes. This vibrant shift has vitalized the academia and industry to share their resources and to create a win-win paradigm of mutual success and technological development along with the human resource development in the field of aerospace. Small student satellites are the latest jargon of academia and more than 100 CUBESAT projects have been executed successfully all over the globe and many new student satellite projects are in the development phase. The small satellite project management requires the application of specific knowledge, skills, tools and techniques to achieve the defined mission requirements. The Authors have presented the detailed outline for the project management of student satellites and presented the role of industry to collaborate with the academia to get the optimized results in academic environment.
Abstract: Speckled images arise when coherent microwave,
optical, and acoustic imaging techniques are used to image an object, surface or scene. Examples of coherent imaging systems include synthetic aperture radar, laser imaging systems, imaging sonar
systems, and medical ultrasound systems. Speckle noise is a form of object or target induced noise that results when the surface of the object is Rayleigh rough compared to the wavelength of the illuminating radiation. Detection and estimation in images corrupted
by speckle noise is complicated by the nature of the noise and is not
as straightforward as detection and estimation in additive noise. In
this work, we derive stochastic models for speckle noise, with an emphasis on speckle as it arises in medical ultrasound images. The
motivation for this work is the problem of segmentation and tissue classification using ultrasound imaging. Modeling of speckle in this
context involves partially developed speckle model where an underlying Poisson point process modulates a Gram-Charlier series
of Laguerre weighted exponential functions, resulting in a doubly
stochastic filtered Poisson point process. The statistical distribution of partially developed speckle is derived in a closed canonical form.
It is observed that as the mean number of scatterers in a resolution cell is increased, the probability density function approaches an
exponential distribution. This is consistent with fully developed speckle noise as demonstrated by the Central Limit theorem.
Abstract: Wireless sensor networks (WSN) consists of many
sensor nodes that are placed on unattended environments such as
military sites in order to collect important information.
Implementing a secure protocol that can prevent forwarding forged
data and modifying content of aggregated data and has low delay
and overhead of communication, computing and storage is very
important. This paper presents a new protocol for concealed data
aggregation (CDA). In this protocol, the network is divided to
virtual cells, nodes within each cell produce a shared key to send
and receive of concealed data with each other. Considering to data
aggregation in each cell is locally and implementing a secure
authentication mechanism, data aggregation delay is very low and
producing false data in the network by malicious nodes is not
possible. To evaluate the performance of our proposed protocol, we
have presented computational models that show the performance
and low overhead in our protocol.
Abstract: Knowledge-based e-mail systems focus on
incorporating knowledge management approach in order to enhance
the traditional e-mail systems. In this paper, we present a knowledgebased
e-mail system called KS-Mail where people do not only send
and receive e-mail conventionally but are also able to create a sense
of knowledge flow. We introduce semantic processing on the e-mail
contents by automatically assigning categories and providing links to
semantically related e-mails. This is done to enrich the knowledge
value of each e-mail as well as to ease the organization of the e-mails
and their contents. At the application level, we have also built
components like the service manager, evaluation engine and search
engine to handle the e-mail processes efficiently by providing the
means to share and reuse knowledge. For this purpose, we present the
KS-Mail architecture, and elaborate on the details of the e-mail
server and the application server. We present the ontology mapping
technique used to achieve the e-mail content-s categorization as well
as the protocols that we have developed to handle the transactions in
the e-mail system. Finally, we discuss further on the implementation
of the modules presented in the KS-Mail architecture.
Abstract: The Object of this paper is to design and analyze a
Hysteresis modulation based sliding mode control (HMSMC) for
positive output elementary super lift Luo converter (POESLLC),
which is the start-of-the-art DC-DC converter. The positive output
elementary super lift Luo converter performs the voltage
conversion from positive source voltage to positive load voltage.
This paper proposes a HMSMC capable of providing the good
steady state and dynamic performance compared to conventional
controllers. Dynamic equations describing the positive output
elementary super lift luo converter are derived by using state space
average method. The simulation model of the positive output
elementary super lift Luo converter with its control circuit is
implemented in Matlab/Simulink. The HMSMC for positive
output elementary super lift Luo converter is tested for line
changes, load changes and also for components variations.