Abstract: The fault detection and diagnosis of complicated
production processes is one of essential tasks needed to run the process
safely with good final product quality. Unexpected events occurred in
the process may have a serious impact on the process. In this work,
triangular representation of process measurement data obtained in an
on-line basis is evaluated using simulation process. The effect of using
linear and nonlinear reduced spaces is also tested. Their diagnosis
performance was demonstrated using multivariate fault data. It has
shown that the nonlinear technique based diagnosis method produced
more reliable results and outperforms linear method. The use of
appropriate reduced space yielded better diagnosis performance. The
presented diagnosis framework is different from existing ones in that it
attempts to extract the fault pattern in the reduced space, not in the
original process variable space. The use of reduced model space helps
to mitigate the sensitivity of the fault pattern to noise.
Abstract: In present work, prediction the effect of nose radius, rz (mm) on the equivalent strain (PEEQ) and surface finish during the machining of titanium alloy (Ti-6Al-4V) through orthogonal cutting process. The results were performed at several of the nose radiuses, rz (mm) while the cutting speed, vc (m/min), feed rate, f (mm/tooth) and depth of cut, d (mm) were remained constant. The equivalent plastic strain (PEEQ) was estimated by using finite element modeling (FEM) and applied through ABAQUS/EXPLICIT software. The simulation results led to conclude that the equivalent plastic strain (PEEQ) was increased and surface roughness (Ra) decreased when increasing nose radius, rz (mm) during the machining of titanium alloy (Ti–6Al–4V) in dry cutting conditions.
Abstract: MultiProtocol Label Switching (MPLS) is an
emerging technology that aims to address many of the existing issues
associated with packet forwarding in today-s Internetworking
environment. It provides a method of forwarding packets at a high
rate of speed by combining the speed and performance of Layer 2
with the scalability and IP intelligence of Layer 3. In a traditional IP
(Internet Protocol) routing network, a router analyzes the destination
IP address contained in the packet header. The router independently
determines the next hop for the packet using the destination IP
address and the interior gateway protocol. This process is repeated at
each hop to deliver the packet to its final destination. In contrast, in
the MPLS forwarding paradigm routers on the edge of the network
(label edge routers) attach labels to packets based on the forwarding
Equivalence class (FEC). Packets are then forwarded through the
MPLS domain, based on their associated FECs , through swapping
the labels by routers in the core of the network called label switch
routers. The act of simply swapping the label instead of referencing
the IP header of the packet in the routing table at each hop provides
a more efficient manner of forwarding packets, which in turn allows
the opportunity for traffic to be forwarded at tremendous speeds and
to have granular control over the path taken by a packet. This paper
deals with the process of MPLS forwarding mechanism,
implementation of MPLS datapath , and test results showing the
performance comparison of MPLS and IP routing. The discussion
will focus primarily on MPLS IP packet networks – by far the
most common application of MPLS today.
Abstract: A thin layer on the component surface can be found
with high tensile residual stresses, due to turning operations, which
can dangerously affect the fatigue performance of the component. In
this paper an analytical approach is presented to reconstruct the
residual stress field from a limited incomplete set of measurements.
Airy stress function is used as the primary unknown to directly solve
the equilibrium equations and satisfying the boundary conditions. In
this new method there exists the flexibility to impose the physical
conditions that govern the behavior of residual stress to achieve a
meaningful complete stress field. The analysis is also coupled to a
least squares approximation and a regularization method to provide
stability of the inverse problem. The power of this new method is
then demonstrated by analyzing some experimental measurements
and achieving a good agreement between the model prediction and
the results obtained from residual stress measurement.
Abstract: Hydroxymethylfurfural (HMF) is formed by thermally
treating products rich in carbohydrates. HMF and other furan
derivatives are toxic.
The aim of the research was to establish the content of HMF in
gingerbread biscuits with honey and sugar syrup additives by using
three leavening agents— ammonium carbonate (NH4HCO3 and
(NH4)2CO3), baking powder, and baking soda (NaHCO3).
The content of HMF is significantly affected by the leavening
agent used. The content of HMF with honey where ammonium
carbonate was used as additive range from 5.7 to 27.3mg 100g-1, but
when sugar syrup is used the content varies from 2.3 to 7.4mg 100g-1.
When baking powder and baking soda are used as leavening agents,
the content of HMF exceeds 4mg 100g-1 in the event honey had been
added and the baking time had been longer (10 minutes at 180°C or
9 minutes at 200°C).
Abstract: To investigates the effect of fiberglass clamping
process improvement on drape simulation prediction. This has
great effect on the mould and the fiber during manufacturing
process. This also, improves the fiber strain, the quality of the
fiber orientation in the area of folding and wrinkles formation
during the press-forming process. Drape simulation software
tool was used to digitalize the process, noting the formation
problems on the contour sensitive part. This was compared
with the real life clamping processes using single and double
frame set-ups to observe the effects. Also, restrains are
introduced by using clips, and the G-clamps with predetermine
revolution to; restrain the fabric deformation during the
forming process.The incorporation of clamping and fabric
restrain deformation improved on the prediction of the
simulation tool. Therefore, for effective forming process,
incorporation of clamping process into the drape simulation
process will assist in the development of fiberglass application
in manufacturing process.
Abstract: Image coding based on clustering provides immediate
access to targeted features of interest in a high quality decoded
image. This approach is useful for intelligent devices, as well as for
multimedia content-based description standards. The result of image
clustering cannot be precise in some positions especially on pixels
with edge information which produce ambiguity among the clusters.
Even with a good enhancement operator based on PDE, the quality of
the decoded image will highly depend on the clustering process. In
this paper, we introduce an ambiguity cluster in image coding to
represent pixels with vagueness properties. The presence of such
cluster allows preserving some details inherent to edges as well for
uncertain pixels. It will also be very useful during the decoding phase
in which an anisotropic diffusion operator, such as Perona-Malik,
enhances the quality of the restored image. This work also offers a
comparative study to demonstrate the effectiveness of a fuzzy
clustering technique in detecting the ambiguity cluster without losing
lot of the essential image information. Several experiments have been
carried out to demonstrate the usefulness of ambiguity concept in
image compression. The coding results and the performance of the
proposed algorithms are discussed in terms of the peak signal-tonoise
ratio and the quantity of ambiguous pixels.
Abstract: This paper presents the results of enhancing images from a left and right stereo pair in order to increase the resolution of a 3D representation of a scene generated from that same pair. A new neural network structure known as a Self Delaying Dynamic Network (SDN) has been used to perform the enhancement. The advantage of SDNs over existing techniques such as bicubic interpolation is their ability to cope with motion and noise effects. SDNs are used to generate two high resolution images, one based on frames taken from the left view of the subject, and one based on the frames from the right. This new high resolution stereo pair is then processed by a disparity map generator. The disparity map generated is compared to two other disparity maps generated from the same scene. The first is a map generated from an original high resolution stereo pair and the second is a map generated using a stereo pair which has been enhanced using bicubic interpolation. The maps generated using the SDN enhanced pairs match more closely the target maps. The addition of extra noise into the input images is less problematic for the SDN system which is still able to out perform bicubic interpolation.
Abstract: In this paper, the feasibility study of using a hybrid
system of ground heat exchangers (GHE) and direct evaporative
cooling system in arid weather condition has been performed. The
model is applied for Yazd and Kerman, two cities with arid weather
condition in Iran. The system composed of three sections: Ground-
Coupled-Circuit (GCC), Direct Evaporative Cooler (DEC) and
Cooling Coil Unite (CCU). The GCC provides the necessary precooling
for DEC. The GCC includes four vertical GHE which are
designed in series configuration. Simulation results show that
hybridization of GCC and DEC could provide comfort condition
whereas DEC alone did not. Based on the results the cooling
effectiveness of a hybrid system is more than unity. Thus, this novel
hybrid system could decrease the air temperature below the ambient
wet-bulb temperature. This environmentally clean and energy
efficient system can be considered as an alternative to the mechanical
vapor compression systems.
Abstract: The sand production problem has led researchers into making various attempts to understand the phenomenon. The generally accepted concept is that the occurrence of sanding is due to the in-situ stress conditions and the induced changes in stress that results in the failure of the reservoir sandstone during hydrocarbon production from wellbores. By using a hypothetical cased (perforated) well, an approach to the problem is presented here by using Finite Element numerical modelling techniques. In addition to the examination of the erosion problem, the influence of certain key parameters is studied in order to ascertain their effect on the failure and subsequent erosion process. The major variables investigated include: drawdown, perforation depth, and the erosion criterion. Also included is the determination of the optimal mud pressure for given operational and reservoir conditions. The improved understanding between parameters enables the choice of optimal values to minimize sanding during oil production.
Abstract: The localized corrosion behavior of laser surface
melted 304L austenitic stainless steel was studied by
potentiodynamic polarization test. The extent of improvement in
corrosion resistance was governed by the preferred orientation and
the percentage of delta ferrite present on the surface of the laser
melted sample. It was established by orientation imaging microscopy
that the highest pitting potential value was obtained when grains were
oriented in the most close- packed [101] direction compared to the
random distribution of the base metal and other laser surface melted
samples oriented in [001] direction. The sample with lower
percentage of ferrite had good pitting resistance.
Abstract: We here propose improved version of elastic graph matching (EGM) as a face detector, called the multi-scale EGM (MS-EGM). In this improvement, Gabor wavelet-based pyramid reduces computational complexity for the feature representation often used in the conventional EGM, but preserving a critical amount of information about an image. The MS-EGM gives us higher detection performance than Viola-Jones object detection algorithm of the AdaBoost Haar-like feature cascade. We also show rapid detection speeds of the MS-EGM, comparable to the Viola-Jones method. We find fruitful benefits in the MS-EGM, in terms of topological feature representation for a face.
Abstract: This work focuses on the remediation of polycyclic
aromatic hydrocarbons (PAHs)-contaminated soil via Fenton
treatment coupled with novel chelating agent (CA). The feasibility of
chelated modified Fenton (MF) treatment to promote PAH oxidation
in artificially contaminated soils was investigated in laboratory scale
batch experiments at natural pH. The effects of adding inorganic and
organic CA are discussed. Experiments using different iron catalyst
to CA ratios were conducted, resulting in hydrogen peroxide: soil:
iron: CA weight ratios that varied from 0.049: 1: 0.072: 0.008 to
0.049: 1: 0.072: 0.067. The results revealed that (1) inorganic CA
could provide much higher PAH removal efficiency and (2) most of
the proposed CAs were more efficient than commonly utilised CAs
even at mild ratio. This work highlights the potential of novel
chelating agents in maintaining a suitable environment throughout
the Fenton treatment, particularly in soils with high buffer capacity.
Abstract: This paper proposes new hybrid approaches for face
recognition. Gabor wavelets representation of face images is an
effective approach for both facial action recognition and face
identification. Perform dimensionality reduction and linear
discriminate analysis on the down sampled Gabor wavelet faces can
increase the discriminate ability. Nearest feature space is extended to
various similarity measures. In our experiments, proposed Gabor
wavelet faces combined with extended neural net feature space
classifier shows very good performance, which can achieve 93 %
maximum correct recognition rate on ORL data set without any preprocessing
step.
Abstract: The feasibility of employing solar radiation for
enhanced Fenton process in degradation of combined chlorpyrifos,
cypermethrin and chlorothalonil pesticides was examined. The effect
of various operating conditions of the process on biodegradability
improvement and mineralization of the pesticides were also
evaluated. The optimum operating conditions for treatment of
aqueous solution containing 100, 50 and 250 mg L-1 chlorpyrifos
cypermethrin and chlorothalonil, respectively were observed to be
H2O2/COD molar ratio 2, H2O2/Fe2+ molar ratio 25 and pH 3. Under
the optimum operating conditions, complete degradation of the
pesticides occurred in 1 min. Biodegradability (BOD5/COD)
increased from zero to 0.36 in 60 min, and COD and TOC removal
were 74.19 and 58.32%, respectively in 60 min. Due to
mineralization of organic carbon, decrease in ammonia-nitrogen from
22 to 4.3 mg L-1 and increase in nitrate from 0.7 to 18.1 mg L-1 in
60 min were recorded. The study indicated that solar photo-Fenton
process can be used for pretreatment of chlorpyrifos, cypermethrin
and chlorothalonil pesticides in aqueous solution for further
biological treatment.
Abstract: The characterization of κ-carrageenan could provide a
better understanding of its functions in biological, medical and
industrial applications. Chemical and physical analyses of
carrageenan from seaweeds, Euchema cottonii L., were done to offer
information on its properties and the effects of Co-60 γ-irradiation on
its thermochemical characteristics. The structural and morphological
characteristics of κ-carrageenan were determined using scanning
electron microscopy (SEM) while the composition, molecular weight
and thermal properties were determined using attenuated total
reflectance Fourier transform infrared spectroscopy (ATR-FTIR), gel
permeation chromatography (GPC), thermal gravimetric analysis
(TGA) and differential scanning calorimetry (DSC). Further chemical
analysis was done using hydrogen-1 nuclear magnetic resonance (1H
NMR) and functional characteristics in terms of biocompatibility
were evaluated using cytotoxicity test.
Abstract: We propose a decoy-pulse protocol for frequency-coded implementation of B92 quantum key distribution protocol. A direct extension of decoy-pulse method to frequency-coding scheme results in security loss as an eavesdropper can distinguish between signal and decoy pulses by measuring the carrier photon number without affecting other statistics. We overcome this problem by optimizing the ratio of carrier photon number of decoy-to-signal pulse to be as close to unity as possible. In our method the switching between signal and decoy pulses is achieved by changing the amplitude of RF signal as opposed to modulating the intensity of optical signal thus reducing system cost. We find an improvement by a factor of 100 approximately in the key generation rate using decoy-state protocol. We also study the effect of source fluctuation on key rate. Our simulation results show a key generation rate of 1.5×10-4/pulse for link lengths up to 70km. Finally, we discuss the optimum value of average photon number of signal pulse for a given key rate while also optimizing the carrier ratio.
Abstract: As the Computed Tomography(CT) requires normally
hundreds of projections to reconstruct the image, patients are exposed
to more X-ray energy, which may cause side effects such as cancer.
Even when the variability of the particles in the object is very less,
Computed Tomography requires many projections for good quality
reconstruction. In this paper, less variability of the particles in an
object has been exploited to obtain good quality reconstruction.
Though the reconstructed image and the original image have same
projections, in general, they need not be the same. In addition
to projections, if a priori information about the image is known,
it is possible to obtain good quality reconstructed image. In this
paper, it has been shown by experimental results why conventional
algorithms fail to reconstruct from a few projections, and an efficient
polynomial time algorithm has been given to reconstruct a bi-level
image from its projections along row and column, and a known sub
image of unknown image with smoothness constraints by reducing the
reconstruction problem to integral max flow problem. This paper also
discusses the necessary and sufficient conditions for uniqueness and
extension of 2D-bi-level image reconstruction to 3D-bi-level image
reconstruction.
Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: Environment both endowed and built are essential for
tourism. However tourism and environment maintains a complex
relationship, where in most cases environment is at the receiving end.
Many tourism development activities have adverse environmental
effects, mainly emanating from construction of general infrastructure
and tourism facilities. These negative impacts of tourism can lead to
the destruction of precious natural resources on which it depends.
These effects vary between locations; and its effect on a hill
destination is highly critical. This study aims at developing a
Sustainable Tourism Planning Model for an environmentally
sensitive tourism destination in Kerala, India. Being part of the
Nilgiri mountain ranges, Munnar falls in the Western Ghats, one of
the biological hotspots in the world. Endowed with a unique high
altitude environment Munnar inherits highly significant ecological
wealth. Giving prime importance to the protection of this ecological
heritage, the study proposes a tourism planning model with resource
conservation and sustainability as the paramount focus. Conceiving a
novel approach towards sustainable tourism planning, the study
proposes to assess tourism attractions using Ecological Sensitivity
Index (ESI) and Tourism Attractiveness Index (TAI). Integration of
these two indices will form the Ecology – Tourism Matrix (ETM),
outlining the base for tourism planning in an environmentally
sensitive destination. The ETM Matrix leads to a classification of
tourism nodes according to its Conservation Significance and
Tourism Significance. The spatial integration of such nodes based on
the Hub & Spoke Principle constitutes sub – regions within the STZ.
Ensuing analyses lead to specific guidelines for the STZ as a whole,
specific tourism nodes, hubs and sub-regions. The study results in a
multi – dimensional output, viz., (1) Classification system for tourism
nodes in an environmentally sensitive region/ destination (2)
Conservation / Tourism Development Strategies and Guidelines for
the micro and macro regions and (3) A Sustainable Tourism Planning
Tool particularly for Ecologically Sensitive Destinations, which can
be adapted for other destinations as well.