Abstract: This research is aimed to find optimal values of parameters of acacia wood chips combustion in a bubbling fluidized bed for electrification within the area of the Royal Thai Navy in Sattahip, Chonburi province, Thailand. The size of wood chips falls in the range of 25 mm in diameter. The bed temperature is set within the range of 800±10 oC with the air flow rate of 2.1-3.1 m/min corresponding to the air-fuel ratio between 0.71 to 1.03. The resulting thermal efficiency is approximately 95% with a thermal output of 474.76 kWth, which produced the electricity 0.131 kW-hr.
Abstract: This experiment aims to demonstrate the efficacy of ceramic powder derived from various sources to inactivate avian influenza virus and its possibility to use in the environment. The ceramics used in the present experiment were derived from chicken feces (CF), scallop shell (SS), polyvinyl chloride (PVC) and soybean (SB). All ceramics were mixed with low pathogenic AIV (LPAIV) H7N1, and then kept at room temperature. The recovered virus was titrated onto Madin-Darby canine kidney (MDCK) cells. All ceramics were assessed the inactivation stability in the environment by keeping under sunlight and under wet-dry condition until reached 7 week or 7 resuspension times respectively. The results indicate that all ceramics have excellent efficacy to inactivate LPAIV. This efficacy can be maintained under the simulated condition. The ceramics are expected to be the good materials for application in the biosecurity system at farms.
Abstract: In order to determine the performance and key design parameters of rocket, the erosion of nozzle throat during solid rocket motor burning have to be calculated. This study aims to predict the nozzle throat erosion in solid rocket motors according to the thrust profile of motor in operating conditions and develop a model for optimum performance of rocket. We investigate the throat radius change in the static test programs. The standard method and thrust coefficient are used for adjusting into the ideal performance for conical nozzles. Pressure and thrust data acquired from the tests are analyzed to determine the instantaneous nozzle throat diameter variation throughout the test duration. The result shows good agreement of calculated correlation comparing with measured erosion rate data showing agreement within 1.6 mm/s. Nozzle thrust coefficient loss is found approximately 24% form nozzle throat erosion during burning.
Abstract: The objective of this study was to investigate the effect of tropical forage source and feeding system on fatty acid composition and antioxidant activity in meat goats. Twenty male crossbred goats (Boer x Saanen), were included in the current study and the study design was assigned to be a 2 x 3 factorial in completely randomized design. All goats were slaughtered after 120 days of experimental period. Dietary tropical roughage sources were grass (Mulata II) and legume (Verano stylo). Both types of roughage were offered to the experimental meat goat as 3 feeding regimes; cut-and-carry, silage and grazing. All goats were fed basal concentrate diet at 1.5% of body weight, and they were fed ad libitum the roughages.Chemical composition, fatty acid profile and antioxidation activity of dietary treatments in all feeding system and longissimus dorsi (LD) muscles in all groups were quantified. The results have shown that the fat content in both types of studied roughage sources ranged from about 2.0% to 4.0% of DM and the fatty acid composition of those was mainly C16:0, C18:2n6 and C18:3n3, with less proportion for C18:1n9. The free-radical scavenging activity of the Mulato II was lower than that of the Verano stylo. The free-radical scavenging activity of the Mulato II was lower than that of the Verano stylo. For LD muscle, the fatty acid composition was mainly C16:0, C18:0 and C18:1n9, with less proportion for C18:2n6. The LD muscle of the goats fed with Mulato II and the Verano stylo by grazing had highest free-radical scavenging activity, compared to those fed with cut-and-carry and silage regime, although there were rather high unsaturated fatty acids in LD muscle. Thus, feeding the meat goats with the Mulato II and Verano stylo by grazing would be beneficial effect for consumers to intake high unsaturated fatty acids and lower risk for oxidation from goat meat.
Abstract: According to biodiesel from microalgae is an attractive fuel for several reasons such as renewable, biodegradable and environmental friendly. Thus, this study, green microalgae Scenedesmus acutus PPNK1 isolated from natural water, was selected based on high growth rates, easy cultivation and high lipid content. The Nile red fluorescence method has been successfully applied to the determination of lipids in S. acutus PPNK1. The combination of the method to the lipid composition in algal cells showed the yellow fluorescence under fluorescent microscope. Interestingly, maximum cell numbers and biomass concentration were obtained at 5.44´107 cells/mL and 1.60 g/L when it was cultivated in BG-11 medium while in case of BG-11 with nitrogen deprivation (N 0.25 g/L), accumulated lipid content in cells (44.67%) was achieved that was higher than that found in case of BG-11 medium at about 2 times (22.63%).
Abstract: This study was conducted to formulate diclofenac sodium-loaded chitosan nanoparticles and to study the effect of formulation compositions on particle size and zeta potential of chitosan nanoparticles (CSN) containing diclofenac sodium (DC) prepared by ionotropic gelation method. It was found that the formulations containing chitosan, DC and tripolyphosphate (TPP) at a weight ratio of 4:1:1, respectively, with various pH provided various systems. At pH 5.0 and 6.0, the obtained systems were turbid because of precipitation of DC and chitosan, respectively. However, the dispersed system of CSN possessing diameter of 108±1 nm and zeta potential of 19±1 mV could be obtained at pH 5.5. These CSN also showed spherical morphology observed via a transmission scanning electron microscope. Change in weight ratio of chitosan:DC:TPP i.e. 1:1:1, 2:1:1, 3:1:1 and 4:1:1 showed that these ratios led to precipitation of particles except for the ratio of 4:1:1 providing CSN properly. The effect of Tween 80 as a stabilizer was also determined. It suggested that increment of Tween 80 concentration to 0.02% w/v could stabilize CSN at least 48 hours. However, increment of Tween 80 to 0.03% w/v led to quick precipitation of particles. The study of effect of TPP suggested that increment of TPP concentration increased particle size but decreased zeta potential. The excess TPP caused precipitation of CSN. Therefore, the optimized CSN was the CSN containing chitosan, DC and TPP at the ratio of 4:1:1and 0.02% w/v Tween 80 prepared at pH 5.5. Their particle size, zeta potential and entrapment efficiency were 128±1 nm, 15±1 mV and 45.8±2.6%, respectively.
Abstract: Field study was conducted to determine the post field soil fertility status responses of pawpaw (Carica papaya L.) var. homestead selection and sunrise-solo orchards to organo-mineral fertilizer (OMF) rates applied at 10, 20 40 t/ha where both the zero t/ha OMF and NPK 15:15:15 at 50 g/plant/month served as control. The result showed that all pawpaw orchards treated with OMF rates recorded significantly (p≤0.01) higher % P, % K, Na and % organic matter in soil compared to applied NPK which recorded lower Na. However, while orchards plated with sole pawpaw were higher in soil bulk density (SBD), orchards with homestead mixture were lower in SBD and significantly lower % organic matter compared to obtainable under sunrise crop mixture which recorded lower Na and Mg. In conclusion, as a result of loosening effect on soil particles, the homestead pawpaw probably due to more rooting activities as well as the addition of organic fertilizer to soils both had significant influence leading to lower SBD.
Abstract: This paper reviewed the relationships between the Knowledge Management (KM) activities and its perceived benefits in the knowledge based organisations. KM activities include: knowledge identification, knowledge acquisition, knowledge application, knowledge sharing, knowledge creation and knowledge preservation. And the perceived benefits of KM are fast customer responsiveness, operation excellence and high innovative intensity. Based on the above review, a conceptual framework for KM implementation in retail business organisations has been proposed. Finally the paper forwarded some limitations of the framework and based on which, directions for future research had been suggested.
Abstract: The Automobile Braking System has a crucial role for safety of the passenger and riding quality of the vehicle. The braking force mainly depends on normal reaction on the wheel and the co-efficient of friction between the tire and the road surface. Whenever a vehicle is loaded, the normal reaction on the rear wheel is increased. Thus the amount of braking force required to halt the vehicle with minimum stopping distance, is based on the pillion load on the vehicle. In this work, in order to vary the braking force in two wheelers, the mechanical leverage which operates the master cylinder is varied based on the pillion load. Thus the amount of braking force developed between ground and tire is varied. This optimum braking force on the disc brake helps in attaining the minimum vehicle stopping distance. In addition to that, it also helps in preventing sliding. Thus the system results in reducing the stopping distance of the two wheelers and providing a better braking efficiency than the conventional braking system.
Abstract: In this paper, a robust decentralized congestion control strategy is developed for a large scale network with Differentiated Services (Diff-Serv) traffic. The network is modeled by a nonlinear fluid flow model corresponding to two classes of traffic, namely the premium traffic and the ordinary traffic. The proposed congestion controller does take into account the associated physical network resource limitations and is shown to be robust to the unknown and time-varying delays. Our proposed decentralized congestion control strategy is developed on the basis of Diff-Serv architecture by utilizing a robust adaptive technique. A Linear Matrix Inequality (LMI) condition is obtained to guarantee the ultimate boundedness of the closed-loop system. Numerical simulation implementations are presented by utilizing the QualNet and Matlab software tools to illustrate the effectiveness and capabilities of our proposed decentralized congestion control strategy.
Abstract: The objective of this study is to investigate the performance of the electrocoagulation process for color and COD removal in palm oil wastewater using a 10 L batch reactor. Iron was used as electrodes and the distance between electrodes was 2 cm. The effects of operating parameters: current voltage (6, 12 and 18 volt), reaction time (5, 15, 30, 45 and 60 min) and initial pH (4 and 9) of treatment efficiency were examine. The result showed that decolorization and COD removal efficiency increased with the increase in current voltage and reaction time. The proper condition for decolorization achieved at initial pH 4 and 9 were current voltage of 12 volt, reaction time 30 min. The decolorization efficiency reached 90.4% and 88.9%, respectively. COD removal was achiveved at current voltage 12 volt, reaction time 15 min. COD removal efficiency was 89.2 % and 83.0%, respectively. From the results, to show electrocoagulation process can treat palm oil mill wastewater in both acidic and basic condition at high efficiency for color and COD removal. Consequently, electrocoagulation process can be used or applied as a post-treatment step to improve the quality of the final discharge in term of color and residual COD removal.
Abstract: In this paper, a low-power digital controller for DC-DC power conversion was presented. The controller generates the pulse-width modulated (PWM) signal from digital inputs provided by analog-to-digital converter (ADC). An efficient and simple design scheme to develop the control unit was discussed. This method allows minimization of the consumed resources of the chip and it is based on direct digital design approach. In this application, with the proposed scheme, nearly half area and two-third of the power consumption was saved compared to the conventional schemes. This work illustrates the possibility of implementing low-power and area-efficient power management circuit using direct digital design based approach.
Abstract: This paper presents the finite difference scheme and the numerical simulation of suspended string. The vibration solutions when the various external forces are taken into account are obtained and compared with the solutions without external force. In addition, we also investigate how the external forces and their powers and coefficients affect the amplitude of vibration.
Abstract: Plenty researches have reported techniques to harvest energy from piezoelectric transducer. In the earlier years, the researches mainly report linear energy harvesting techniques whereby interface circuitry is designed to have input impedance that match with the impedance of the piezoelectric transducer. In recent years non-linear techniques become more popular. The non-linear technique employs voltage waveform manipulation to boost the available-for-extraction energy at the time of energy transfer. The fact that non-linear energy extraction provides larger available-for-extraction energy doesn’t mean the linear energy extraction is completely obsolete. In some scenarios, such as where initial power is not available, linear energy extraction is still preferred. A modified Buck Boost circuit which is capable of harvesting piezoelectric energy using both linear and non-linear techniques is reported in this paper. Efficiency of at least 64% can be achieved using this circuit. For linear extraction, the modified Buck Boost circuit is controlled using a fix frequency and duty cycle clock. A voltage sensor and a pulse generator are added as the controller for the non-linear extraction technique.
Abstract: A silicon photomultiplier (SiPM) was designed, fabricated and characterized. The SiPM was based on SACM (Separation of Absorption, Charge and Multiplication) structure, which was optimized for blue light detection in application of positron emission tomography (PET). The achieved SiPM array has a high geometric fill factor of 64% and a low breakdown voltage of about 22V, while the temperature dependence of breakdown voltage is only 17mV/°C. The gain and photon detection efficiency of the device achieved were also measured under illumination of light at 405nm and 460nm wavelengths. The gain of the device is in the order of 106. The photon detection efficiency up to 60% has been observed under 1.8V overvoltage.
Abstract: The performance of state of the art worldwide telecommunication networks strongly depends on the efficiency of the applied routing mechanism. Game theoretical approaches to this problem offer new solutions. In this paper a new continuous network routing model is defined to describe data transfer in fixed telecommunication networks of multiple hosts. The nodes of the network correspond to routers whose latency is assumed to be traffic dependent. We propose that the whole traffic of the network can be decomposed to a finite number of tasks, which belong to various hosts. To describe the different latency-sensitivity, utility functions are defined for each task. The model is used to compare router and host intelligent types of routing methods, corresponding to various data transfer protocols. We analyze host intelligent routing as a transferable utility cooperative game with externalities. The main aim of the paper is to provide a framework in which the efficiency of various routing algorithms can be compared and the transferable utility game arising in the cooperative case can be analyzed.
Abstract: In this paper a genetic algorithm (GA) with dual-fitness function is proposed and applied to solve the deterministic identical machine scheduling problem. The mating fitness function value was used to determine the mating for chromosomes, while the selection fitness function value was used to determine their survivals. The performance of this algorithm was tested on deterministic identical machine scheduling using simulated data. The results obtained from the proposed GA were compared with classical GA and integer programming (IP). Results showed that dual-fitness function GA outperformed the classical single-fitness function GA with statistical significance for large problems and was competitive to IP, particularly when large size problems were used.
Abstract: The purpose of the research is to investigate the energetic feature of the backpack load on soldier’s gait with variation of the trunk flexion angle. It is believed that the trunk flexion variation of the loaded gait may cause a significant difference in the energy cost which is often in practice in daily life. To this end, seven healthy Korea military personnel participated in the experiment and are tested under three different walking postures comprised of the small, natural and large trunk flexion. There are around 5 degree differences of waist angle between each trunk flexion. The ground reaction forces were collected from the force plates and motion kinematic data are measured by the motion capture system. Based on these data, the impulses, momentums and mechanical works done on the center of body mass (COM) during the double support phase were computed. The result shows that the push-off and heel strike impulse are not relevant to the trunk flexion change, however the mechanical work by the push-off and heel strike were changed by the trunk flexion variation. It is because the vertical velocity of the COM during the double support phase is increased significantly with an increase in the trunk flexion. Therefore, we can know that the gait efficiency of the loaded gait depends on the trunk flexion angle. Also, even though the gravitational impulse and pre-collision momentum are changed by the trunk flexion variation, the after-collision momentum is almost constant regardless of the trunk flexion variation.
Abstract: Microorganisms can be removed, inhibited or killed by physical agents, physical processes or chemical agents but they have their inherent disadvantages such as increased resistance against antibiotics etc. Since, plants have endless ability to synthesize aromatic substances which act as the master agents for plant defense mechanisms against microorganisms, insects and herbivores. Thus, secondary metabolites or phytochemicals obtained from plants can be used as agents of disease control nowadays. In the present study effect of different concentrations of acetone fraction of leaves and alcohol fraction of inflorescence of Euphorbia pulcherrima on various cytomorphological parameters i.e. cell number, mycelium width, conidial size, conidiophore size etc. of Aspergillus fumigatus has been studied. Change in mycelium/ hyphal cell width, conidium size, conidiophore size etc. was measured with the help of a previously calibrated oculometer. To study effect on morphology, fungal mycelium along with conidiophore and conidia were stained with cotton blue and mounted in lactophenol and observed microscopically. Inhibitory action of the acetone extract of Euphorbia pulcherrima leaf on growth of Aspergillus fumigatus was investigated. Control containing extract free medium supported profuse growth of the fungus. Although decrease in growth was observed even at 3.95μg/ml but significant inhibition of growth was started at7.81μg/ml concentration of the extract. Complete inhibition was observed at 15.62μg/ml and above. Microscopic examination revealed that at 3.95, 7.81 and 15.62μg/ml extract concentration hyphal cell width was found to be increased from 1.44μm in control to 3.86, 5.24 and 8.98 μm respectively giving a beaded appearance to the mycelium. Vesicle size was reduced from 24.78x20.08μm (control) to 11.34x10.06μm at 3.95μg/ml concentration. At 7.81 and 15.62μg/ml concentration no phialides and sterigmata were observed. Inhibitory action of the alcohol extract of inflorescence on the growth of Aspergillus fumigatus was also studied. Control containing extract free medium supported profuse growth of the fungus. Although decrease in growth was observed even at 3.95μg/ml but complete inhibition was observed at 62.5μg/ml and above. Microscopic examination revealed that hyphal cell width of Aspergillus fumigatus was found to be increased from 1.67μm in control to 5.84μm at MIC i.e. at 62.5μg/ml. Vesicle size was reduced from 44.76x 24.22μm (control) to 11.36x 6.80μm at 15.62μg/ml concentrations. At 31.25 μg/ml and 62.5μg/ml concentration no phialides and sterigmata was found. Spore germination was completely found to be inhibited at 3.95μg/ml concentration. Similarly 92.87% reduction in vesicle size was observed at 15.62μg/ml concentration. It is evident from the results that plant extracts inhibit fungal growth and this inhibition is concentration dependent.
Abstract: Intercalation imparts interesting features to the host graphite material. Two different types of intercalated compounds called (GIC-bisulphate or Nyex 1000 and GIC-nitrate or Nyex 3000) were tested for their adsorption capacity and ability to undergo electrochemical regeneration. It was found that Nyex 3000 showed comparatively slow kinetics along with reduced adsorption capacity to one half for acid violet 17 as adsorbate. Acid violet 17 was selected as model organic pollutant for evaluating comparative performance of said adsorbents. Both adsorbent materials showed 100% regeneration efficiency as achieved by passing a charge of 36 C g-1 at a current density of 12 mA cm-2 and a treatment time of 60 min.